--- /dev/null
+/*
+ * Tehuti Networks(R) Network Driver
+ * ethtool interface implementation
+ * Copyright (C) 2007 Tehuti Networks Ltd. All rights reserved
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+/*
+ * RX HW/SW interaction overview
+ * ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+ * There are 2 types of RX communication channels between driver and NIC.
+ * 1) RX Free Fifo - RXF - holds descriptors of empty buffers to accept incoming
+ * traffic. This Fifo is filled by SW and is readen by HW. Each descriptor holds
+ * info about buffer's location, size and ID. An ID field is used to identify a
+ * buffer when it's returned with data via RXD Fifo (see below)
+ * 2) RX Data Fifo - RXD - holds descriptors of full buffers. This Fifo is
+ * filled by HW and is readen by SW. Each descriptor holds status and ID.
+ * HW pops descriptor from RXF Fifo, stores ID, fills buffer with incoming data,
+ * via dma moves it into host memory, builds new RXD descriptor with same ID,
+ * pushes it into RXD Fifo and raises interrupt to indicate new RX data.
+ *
+ * Current NIC configuration (registers + firmware) makes NIC use 2 RXF Fifos.
+ * One holds 1.5K packets and another - 26K packets. Depending on incoming
+ * packet size, HW desides on a RXF Fifo to pop buffer from. When packet is
+ * filled with data, HW builds new RXD descriptor for it and push it into single
+ * RXD Fifo.
+ *
+ * RX SW Data Structures
+ * ~~~~~~~~~~~~~~~~~~~~~
+ * skb db - used to keep track of all skbs owned by SW and their dma addresses.
+ * For RX case, ownership lasts from allocating new empty skb for RXF until
+ * accepting full skb from RXD and passing it to OS. Each RXF Fifo has its own
+ * skb db. Implemented as array with bitmask.
+ * fifo - keeps info about fifo's size and location, relevant HW registers,
+ * usage and skb db. Each RXD and RXF Fifo has its own fifo structure.
+ * Implemented as simple struct.
+ *
+ * RX SW Execution Flow
+ * ~~~~~~~~~~~~~~~~~~~~
+ * Upon initialization (ifconfig up) driver creates RX fifos and initializes
+ * relevant registers. At the end of init phase, driver enables interrupts.
+ * NIC sees that there is no RXF buffers and raises
+ * RD_INTR interrupt, isr fills skbs and Rx begins.
+ * Driver has two receive operation modes:
+ * NAPI - interrupt-driven mixed with polling
+ * interrupt-driven only
+ *
+ * Interrupt-driven only flow is following. When buffer is ready, HW raises
+ * interrupt and isr is called. isr collects all available packets
+ * (bdx_rx_receive), refills skbs (bdx_rx_alloc_skbs) and exit.
+
+ * Rx buffer allocation note
+ * ~~~~~~~~~~~~~~~~~~~~~~~~~
+ * Driver cares to feed such amount of RxF descriptors that respective amount of
+ * RxD descriptors can not fill entire RxD fifo. The main reason is lack of
+ * overflow check in Bordeaux for RxD fifo free/used size.
+ * FIXME: this is NOT fully implemented, more work should be done
+ *
+ */
+
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
+#include "tehuti.h"
+
+static const struct pci_device_id bdx_pci_tbl[] = {
+ { PCI_VDEVICE(TEHUTI, 0x3009), },
+ { PCI_VDEVICE(TEHUTI, 0x3010), },
+ { PCI_VDEVICE(TEHUTI, 0x3014), },
+ { 0 }
+};
+
+MODULE_DEVICE_TABLE(pci, bdx_pci_tbl);
+
+/* Definitions needed by ISR or NAPI functions */
+static void bdx_rx_alloc_skbs(struct bdx_priv *priv, struct rxf_fifo *f);
+static void bdx_tx_cleanup(struct bdx_priv *priv);
+static int bdx_rx_receive(struct bdx_priv *priv, struct rxd_fifo *f, int budget);
+
+/* Definitions needed by FW loading */
+static void bdx_tx_push_desc_safe(struct bdx_priv *priv, void *data, int size);
+
+/* Definitions needed by hw_start */
+static int bdx_tx_init(struct bdx_priv *priv);
+static int bdx_rx_init(struct bdx_priv *priv);
+
+/* Definitions needed by bdx_close */
+static void bdx_rx_free(struct bdx_priv *priv);
+static void bdx_tx_free(struct bdx_priv *priv);
+
+/* Definitions needed by bdx_probe */
+static void bdx_set_ethtool_ops(struct net_device *netdev);
+
+/*************************************************************************
+ * Print Info *
+ *************************************************************************/
+
+static void print_hw_id(struct pci_dev *pdev)
+{
+ struct pci_nic *nic = pci_get_drvdata(pdev);
+ u16 pci_link_status = 0;
+ u16 pci_ctrl = 0;
+
+ pci_read_config_word(pdev, PCI_LINK_STATUS_REG, &pci_link_status);
+ pci_read_config_word(pdev, PCI_DEV_CTRL_REG, &pci_ctrl);
+
+ pr_info("%s%s\n", BDX_NIC_NAME,
+ nic->port_num == 1 ? "" : ", 2-Port");
+ pr_info("srom 0x%x fpga %d build %u lane# %d max_pl 0x%x mrrs 0x%x\n",
+ readl(nic->regs + SROM_VER), readl(nic->regs + FPGA_VER) & 0xFFF,
+ readl(nic->regs + FPGA_SEED),
+ GET_LINK_STATUS_LANES(pci_link_status),
+ GET_DEV_CTRL_MAXPL(pci_ctrl), GET_DEV_CTRL_MRRS(pci_ctrl));
+}
+
+static void print_fw_id(struct pci_nic *nic)
+{
+ pr_info("fw 0x%x\n", readl(nic->regs + FW_VER));
+}
+
+static void print_eth_id(struct net_device *ndev)
+{
+ netdev_info(ndev, "%s, Port %c\n",
+ BDX_NIC_NAME, (ndev->if_port == 0) ? 'A' : 'B');
+
+}
+
+/*************************************************************************
+ * Code *
+ *************************************************************************/
+
+#define bdx_enable_interrupts(priv) \
+ do { WRITE_REG(priv, regIMR, IR_RUN); } while (0)
+#define bdx_disable_interrupts(priv) \
+ do { WRITE_REG(priv, regIMR, 0); } while (0)
+
+/**
+ * bdx_fifo_init - create TX/RX descriptor fifo for host-NIC communication.
+ * @priv: NIC private structure
+ * @f: fifo to initialize
+ * @fsz_type: fifo size type: 0-4KB, 1-8KB, 2-16KB, 3-32KB
+ * @reg_XXX: offsets of registers relative to base address
+ *
+ * 1K extra space is allocated at the end of the fifo to simplify
+ * processing of descriptors that wraps around fifo's end
+ *
+ * Returns 0 on success, negative value on failure
+ *
+ */
+static int
+bdx_fifo_init(struct bdx_priv *priv, struct fifo *f, int fsz_type,
+ u16 reg_CFG0, u16 reg_CFG1, u16 reg_RPTR, u16 reg_WPTR)
+{
+ u16 memsz = FIFO_SIZE * (1 << fsz_type);
+
+ memset(f, 0, sizeof(struct fifo));
+ /* pci_alloc_consistent gives us 4k-aligned memory */
+ f->va = pci_alloc_consistent(priv->pdev,
+ memsz + FIFO_EXTRA_SPACE, &f->da);
+ if (!f->va) {
+ pr_err("pci_alloc_consistent failed\n");
+ RET(-ENOMEM);
+ }
+ f->reg_CFG0 = reg_CFG0;
+ f->reg_CFG1 = reg_CFG1;
+ f->reg_RPTR = reg_RPTR;
+ f->reg_WPTR = reg_WPTR;
+ f->rptr = 0;
+ f->wptr = 0;
+ f->memsz = memsz;
+ f->size_mask = memsz - 1;
+ WRITE_REG(priv, reg_CFG0, (u32) ((f->da & TX_RX_CFG0_BASE) | fsz_type));
+ WRITE_REG(priv, reg_CFG1, H32_64(f->da));
+
+ RET(0);
+}
+
+/**
+ * bdx_fifo_free - free all resources used by fifo
+ * @priv: NIC private structure
+ * @f: fifo to release
+ */
+static void bdx_fifo_free(struct bdx_priv *priv, struct fifo *f)
+{
+ ENTER;
+ if (f->va) {
+ pci_free_consistent(priv->pdev,
+ f->memsz + FIFO_EXTRA_SPACE, f->va, f->da);
+ f->va = NULL;
+ }
+ RET();
+}
+
+/**
+ * bdx_link_changed - notifies OS about hw link state.
+ * @priv: hw adapter structure
+ */
+static void bdx_link_changed(struct bdx_priv *priv)
+{
+ u32 link = READ_REG(priv, regMAC_LNK_STAT) & MAC_LINK_STAT;
+
+ if (!link) {
+ if (netif_carrier_ok(priv->ndev)) {
+ netif_stop_queue(priv->ndev);
+ netif_carrier_off(priv->ndev);
+ netdev_err(priv->ndev, "Link Down\n");
+ }
+ } else {
+ if (!netif_carrier_ok(priv->ndev)) {
+ netif_wake_queue(priv->ndev);
+ netif_carrier_on(priv->ndev);
+ netdev_err(priv->ndev, "Link Up\n");
+ }
+ }
+}
+
+static void bdx_isr_extra(struct bdx_priv *priv, u32 isr)
+{
+ if (isr & IR_RX_FREE_0) {
+ bdx_rx_alloc_skbs(priv, &priv->rxf_fifo0);
+ DBG("RX_FREE_0\n");
+ }
+
+ if (isr & IR_LNKCHG0)
+ bdx_link_changed(priv);
+
+ if (isr & IR_PCIE_LINK)
+ netdev_err(priv->ndev, "PCI-E Link Fault\n");
+
+ if (isr & IR_PCIE_TOUT)
+ netdev_err(priv->ndev, "PCI-E Time Out\n");
+
+}
+
+/**
+ * bdx_isr_napi - Interrupt Service Routine for Bordeaux NIC
+ * @irq: interrupt number
+ * @dev: network device
+ *
+ * Return IRQ_NONE if it was not our interrupt, IRQ_HANDLED - otherwise
+ *
+ * It reads ISR register to know interrupt reasons, and proceed them one by one.
+ * Reasons of interest are:
+ * RX_DESC - new packet has arrived and RXD fifo holds its descriptor
+ * RX_FREE - number of free Rx buffers in RXF fifo gets low
+ * TX_FREE - packet was transmited and RXF fifo holds its descriptor
+ */
+
+static irqreturn_t bdx_isr_napi(int irq, void *dev)
+{
+ struct net_device *ndev = dev;
+ struct bdx_priv *priv = netdev_priv(ndev);
+ u32 isr;
+
+ ENTER;
+ isr = (READ_REG(priv, regISR) & IR_RUN);
+ if (unlikely(!isr)) {
+ bdx_enable_interrupts(priv);
+ return IRQ_NONE; /* Not our interrupt */
+ }
+
+ if (isr & IR_EXTRA)
+ bdx_isr_extra(priv, isr);
+
+ if (isr & (IR_RX_DESC_0 | IR_TX_FREE_0)) {
+ if (likely(napi_schedule_prep(&priv->napi))) {
+ __napi_schedule(&priv->napi);
+ RET(IRQ_HANDLED);
+ } else {
+ /* NOTE: we get here if intr has slipped into window
+ * between these lines in bdx_poll:
+ * bdx_enable_interrupts(priv);
+ * return 0;
+ * currently intrs are disabled (since we read ISR),
+ * and we have failed to register next poll.
+ * so we read the regs to trigger chip
+ * and allow further interupts. */
+ READ_REG(priv, regTXF_WPTR_0);
+ READ_REG(priv, regRXD_WPTR_0);
+ }
+ }
+
+ bdx_enable_interrupts(priv);
+ RET(IRQ_HANDLED);
+}
+
+static int bdx_poll(struct napi_struct *napi, int budget)
+{
+ struct bdx_priv *priv = container_of(napi, struct bdx_priv, napi);
+ int work_done;
+
+ ENTER;
+ bdx_tx_cleanup(priv);
+ work_done = bdx_rx_receive(priv, &priv->rxd_fifo0, budget);
+ if ((work_done < budget) ||
+ (priv->napi_stop++ >= 30)) {
+ DBG("rx poll is done. backing to isr-driven\n");
+
+ /* from time to time we exit to let NAPI layer release
+ * device lock and allow waiting tasks (eg rmmod) to advance) */
+ priv->napi_stop = 0;
+
+ napi_complete(napi);
+ bdx_enable_interrupts(priv);
+ }
+ return work_done;
+}
+
+/**
+ * bdx_fw_load - loads firmware to NIC
+ * @priv: NIC private structure
+ *
+ * Firmware is loaded via TXD fifo, so it must be initialized first.
+ * Firware must be loaded once per NIC not per PCI device provided by NIC (NIC
+ * can have few of them). So all drivers use semaphore register to choose one
+ * that will actually load FW to NIC.
+ */
+
+static int bdx_fw_load(struct bdx_priv *priv)
+{
+ const struct firmware *fw = NULL;
+ int master, i;
+ int rc;
+
+ ENTER;
+ master = READ_REG(priv, regINIT_SEMAPHORE);
+ if (!READ_REG(priv, regINIT_STATUS) && master) {
+ rc = request_firmware(&fw, "tehuti/bdx.bin", &priv->pdev->dev);
+ if (rc)
+ goto out;
+ bdx_tx_push_desc_safe(priv, (char *)fw->data, fw->size);
+ mdelay(100);
+ }
+ for (i = 0; i < 200; i++) {
+ if (READ_REG(priv, regINIT_STATUS)) {
+ rc = 0;
+ goto out;
+ }
+ mdelay(2);
+ }
+ rc = -EIO;
+out:
+ if (master)
+ WRITE_REG(priv, regINIT_SEMAPHORE, 1);
+
+ release_firmware(fw);
+
+ if (rc) {
+ netdev_err(priv->ndev, "firmware loading failed\n");
+ if (rc == -EIO)
+ DBG("VPC = 0x%x VIC = 0x%x INIT_STATUS = 0x%x i=%d\n",
+ READ_REG(priv, regVPC),
+ READ_REG(priv, regVIC),
+ READ_REG(priv, regINIT_STATUS), i);
+ RET(rc);
+ } else {
+ DBG("%s: firmware loading success\n", priv->ndev->name);
+ RET(0);
+ }
+}
+
+static void bdx_restore_mac(struct net_device *ndev, struct bdx_priv *priv)
+{
+ u32 val;
+
+ ENTER;
+ DBG("mac0=%x mac1=%x mac2=%x\n",
+ READ_REG(priv, regUNC_MAC0_A),
+ READ_REG(priv, regUNC_MAC1_A), READ_REG(priv, regUNC_MAC2_A));
+
+ val = (ndev->dev_addr[0] << 8) | (ndev->dev_addr[1]);
+ WRITE_REG(priv, regUNC_MAC2_A, val);
+ val = (ndev->dev_addr[2] << 8) | (ndev->dev_addr[3]);
+ WRITE_REG(priv, regUNC_MAC1_A, val);
+ val = (ndev->dev_addr[4] << 8) | (ndev->dev_addr[5]);
+ WRITE_REG(priv, regUNC_MAC0_A, val);
+
+ DBG("mac0=%x mac1=%x mac2=%x\n",
+ READ_REG(priv, regUNC_MAC0_A),
+ READ_REG(priv, regUNC_MAC1_A), READ_REG(priv, regUNC_MAC2_A));
+ RET();
+}
+
+/**
+ * bdx_hw_start - inits registers and starts HW's Rx and Tx engines
+ * @priv: NIC private structure
+ */
+static int bdx_hw_start(struct bdx_priv *priv)
+{
+ int rc = -EIO;
+ struct net_device *ndev = priv->ndev;
+
+ ENTER;
+ bdx_link_changed(priv);
+
+ /* 10G overall max length (vlan, eth&ip header, ip payload, crc) */
+ WRITE_REG(priv, regFRM_LENGTH, 0X3FE0);
+ WRITE_REG(priv, regPAUSE_QUANT, 0x96);
+ WRITE_REG(priv, regRX_FIFO_SECTION, 0x800010);
+ WRITE_REG(priv, regTX_FIFO_SECTION, 0xE00010);
+ WRITE_REG(priv, regRX_FULLNESS, 0);
+ WRITE_REG(priv, regTX_FULLNESS, 0);
+ WRITE_REG(priv, regCTRLST,
+ regCTRLST_BASE | regCTRLST_RX_ENA | regCTRLST_TX_ENA);
+
+ WRITE_REG(priv, regVGLB, 0);
+ WRITE_REG(priv, regMAX_FRAME_A,
+ priv->rxf_fifo0.m.pktsz & MAX_FRAME_AB_VAL);
+
+ DBG("RDINTCM=%08x\n", priv->rdintcm); /*NOTE: test script uses this */
+ WRITE_REG(priv, regRDINTCM0, priv->rdintcm);
+ WRITE_REG(priv, regRDINTCM2, 0); /*cpu_to_le32(rcm.val)); */
+
+ DBG("TDINTCM=%08x\n", priv->tdintcm); /*NOTE: test script uses this */
+ WRITE_REG(priv, regTDINTCM0, priv->tdintcm); /* old val = 0x300064 */
+
+ /* Enable timer interrupt once in 2 secs. */
+ /*WRITE_REG(priv, regGTMR0, ((GTMR_SEC * 2) & GTMR_DATA)); */
+ bdx_restore_mac(priv->ndev, priv);
+
+ WRITE_REG(priv, regGMAC_RXF_A, GMAC_RX_FILTER_OSEN |
+ GMAC_RX_FILTER_AM | GMAC_RX_FILTER_AB);
+
+#define BDX_IRQ_TYPE ((priv->nic->irq_type == IRQ_MSI) ? 0 : IRQF_SHARED)
+
+ rc = request_irq(priv->pdev->irq, bdx_isr_napi, BDX_IRQ_TYPE,
+ ndev->name, ndev);
+ if (rc)
+ goto err_irq;
+ bdx_enable_interrupts(priv);
+
+ RET(0);
+
+err_irq:
+ RET(rc);
+}
+
+static void bdx_hw_stop(struct bdx_priv *priv)
+{
+ ENTER;
+ bdx_disable_interrupts(priv);
+ free_irq(priv->pdev->irq, priv->ndev);
+
+ netif_carrier_off(priv->ndev);
+ netif_stop_queue(priv->ndev);
+
+ RET();
+}
+
+static int bdx_hw_reset_direct(void __iomem *regs)
+{
+ u32 val, i;
+ ENTER;
+
+ /* reset sequences: read, write 1, read, write 0 */
+ val = readl(regs + regCLKPLL);
+ writel((val | CLKPLL_SFTRST) + 0x8, regs + regCLKPLL);
+ udelay(50);
+ val = readl(regs + regCLKPLL);
+ writel(val & ~CLKPLL_SFTRST, regs + regCLKPLL);
+
+ /* check that the PLLs are locked and reset ended */
+ for (i = 0; i < 70; i++, mdelay(10))
+ if ((readl(regs + regCLKPLL) & CLKPLL_LKD) == CLKPLL_LKD) {
+ /* do any PCI-E read transaction */
+ readl(regs + regRXD_CFG0_0);
+ return 0;
+ }
+ pr_err("HW reset failed\n");
+ return 1; /* failure */
+}
+
+static int bdx_hw_reset(struct bdx_priv *priv)
+{
+ u32 val, i;
+ ENTER;
+
+ if (priv->port == 0) {
+ /* reset sequences: read, write 1, read, write 0 */
+ val = READ_REG(priv, regCLKPLL);
+ WRITE_REG(priv, regCLKPLL, (val | CLKPLL_SFTRST) + 0x8);
+ udelay(50);
+ val = READ_REG(priv, regCLKPLL);
+ WRITE_REG(priv, regCLKPLL, val & ~CLKPLL_SFTRST);
+ }
+ /* check that the PLLs are locked and reset ended */
+ for (i = 0; i < 70; i++, mdelay(10))
+ if ((READ_REG(priv, regCLKPLL) & CLKPLL_LKD) == CLKPLL_LKD) {
+ /* do any PCI-E read transaction */
+ READ_REG(priv, regRXD_CFG0_0);
+ return 0;
+ }
+ pr_err("HW reset failed\n");
+ return 1; /* failure */
+}
+
+static int bdx_sw_reset(struct bdx_priv *priv)
+{
+ int i;
+
+ ENTER;
+ /* 1. load MAC (obsolete) */
+ /* 2. disable Rx (and Tx) */
+ WRITE_REG(priv, regGMAC_RXF_A, 0);
+ mdelay(100);
+ /* 3. disable port */
+ WRITE_REG(priv, regDIS_PORT, 1);
+ /* 4. disable queue */
+ WRITE_REG(priv, regDIS_QU, 1);
+ /* 5. wait until hw is disabled */
+ for (i = 0; i < 50; i++) {
+ if (READ_REG(priv, regRST_PORT) & 1)
+ break;
+ mdelay(10);
+ }
+ if (i == 50)
+ netdev_err(priv->ndev, "SW reset timeout. continuing anyway\n");
+
+ /* 6. disable intrs */
+ WRITE_REG(priv, regRDINTCM0, 0);
+ WRITE_REG(priv, regTDINTCM0, 0);
+ WRITE_REG(priv, regIMR, 0);
+ READ_REG(priv, regISR);
+
+ /* 7. reset queue */
+ WRITE_REG(priv, regRST_QU, 1);
+ /* 8. reset port */
+ WRITE_REG(priv, regRST_PORT, 1);
+ /* 9. zero all read and write pointers */
+ for (i = regTXD_WPTR_0; i <= regTXF_RPTR_3; i += 0x10)
+ DBG("%x = %x\n", i, READ_REG(priv, i) & TXF_WPTR_WR_PTR);
+ for (i = regTXD_WPTR_0; i <= regTXF_RPTR_3; i += 0x10)
+ WRITE_REG(priv, i, 0);
+ /* 10. unseet port disable */
+ WRITE_REG(priv, regDIS_PORT, 0);
+ /* 11. unset queue disable */
+ WRITE_REG(priv, regDIS_QU, 0);
+ /* 12. unset queue reset */
+ WRITE_REG(priv, regRST_QU, 0);
+ /* 13. unset port reset */
+ WRITE_REG(priv, regRST_PORT, 0);
+ /* 14. enable Rx */
+ /* skiped. will be done later */
+ /* 15. save MAC (obsolete) */
+ for (i = regTXD_WPTR_0; i <= regTXF_RPTR_3; i += 0x10)
+ DBG("%x = %x\n", i, READ_REG(priv, i) & TXF_WPTR_WR_PTR);
+
+ RET(0);
+}
+
+/* bdx_reset - performs right type of reset depending on hw type */
+static int bdx_reset(struct bdx_priv *priv)
+{
+ ENTER;
+ RET((priv->pdev->device == 0x3009)
+ ? bdx_hw_reset(priv)
+ : bdx_sw_reset(priv));
+}
+
+/**
+ * bdx_close - Disables a network interface
+ * @netdev: network interface device structure
+ *
+ * Returns 0, this is not allowed to fail
+ *
+ * The close entry point is called when an interface is de-activated
+ * by the OS. The hardware is still under the drivers control, but
+ * needs to be disabled. A global MAC reset is issued to stop the
+ * hardware, and all transmit and receive resources are freed.
+ **/
+static int bdx_close(struct net_device *ndev)
+{
+ struct bdx_priv *priv = NULL;
+
+ ENTER;
+ priv = netdev_priv(ndev);
+
+ napi_disable(&priv->napi);
+
+ bdx_reset(priv);
+ bdx_hw_stop(priv);
+ bdx_rx_free(priv);
+ bdx_tx_free(priv);
+ RET(0);
+}
+
+/**
+ * bdx_open - Called when a network interface is made active
+ * @netdev: network interface device structure
+ *
+ * Returns 0 on success, negative value on failure
+ *
+ * The open entry point is called when a network interface is made
+ * active by the system (IFF_UP). At this point all resources needed
+ * for transmit and receive operations are allocated, the interrupt
+ * handler is registered with the OS, the watchdog timer is started,
+ * and the stack is notified that the interface is ready.
+ **/
+static int bdx_open(struct net_device *ndev)
+{
+ struct bdx_priv *priv;
+ int rc;
+
+ ENTER;
+ priv = netdev_priv(ndev);
+ bdx_reset(priv);
+ if (netif_running(ndev))
+ netif_stop_queue(priv->ndev);
+
+ if ((rc = bdx_tx_init(priv)) ||
+ (rc = bdx_rx_init(priv)) ||
+ (rc = bdx_fw_load(priv)))
+ goto err;
+
+ bdx_rx_alloc_skbs(priv, &priv->rxf_fifo0);
+
+ rc = bdx_hw_start(priv);
+ if (rc)
+ goto err;
+
+ napi_enable(&priv->napi);
+
+ print_fw_id(priv->nic);
+
+ RET(0);
+
+err:
+ bdx_close(ndev);
+ RET(rc);
+}
+
+static int bdx_range_check(struct bdx_priv *priv, u32 offset)
+{
+ return (offset > (u32) (BDX_REGS_SIZE / priv->nic->port_num)) ?
+ -EINVAL : 0;
+}
+
+static int bdx_ioctl_priv(struct net_device *ndev, struct ifreq *ifr, int cmd)
+{
+ struct bdx_priv *priv = netdev_priv(ndev);
+ u32 data[3];
+ int error;
+
+ ENTER;
+
+ DBG("jiffies=%ld cmd=%d\n", jiffies, cmd);
+ if (cmd != SIOCDEVPRIVATE) {
+ error = copy_from_user(data, ifr->ifr_data, sizeof(data));
+ if (error) {
+ pr_err("can't copy from user\n");
+ RET(-EFAULT);
+ }
+ DBG("%d 0x%x 0x%x\n", data[0], data[1], data[2]);
+ }
+
+ if (!capable(CAP_SYS_RAWIO))
+ return -EPERM;
+
+ switch (data[0]) {
+
+ case BDX_OP_READ:
+ error = bdx_range_check(priv, data[1]);
+ if (error < 0)
+ return error;
+ data[2] = READ_REG(priv, data[1]);
+ DBG("read_reg(0x%x)=0x%x (dec %d)\n", data[1], data[2],
+ data[2]);
+ error = copy_to_user(ifr->ifr_data, data, sizeof(data));
+ if (error)
+ RET(-EFAULT);
+ break;
+
+ case BDX_OP_WRITE:
+ error = bdx_range_check(priv, data[1]);
+ if (error < 0)
+ return error;
+ WRITE_REG(priv, data[1], data[2]);
+ DBG("write_reg(0x%x, 0x%x)\n", data[1], data[2]);
+ break;
+
+ default:
+ RET(-EOPNOTSUPP);
+ }
+ return 0;
+}
+
+static int bdx_ioctl(struct net_device *ndev, struct ifreq *ifr, int cmd)
+{
+ ENTER;
+ if (cmd >= SIOCDEVPRIVATE && cmd <= (SIOCDEVPRIVATE + 15))
+ RET(bdx_ioctl_priv(ndev, ifr, cmd));
+ else
+ RET(-EOPNOTSUPP);
+}
+
+/**
+ * __bdx_vlan_rx_vid - private helper for adding/killing VLAN vid
+ * @ndev: network device
+ * @vid: VLAN vid
+ * @op: add or kill operation
+ *
+ * Passes VLAN filter table to hardware
+ */
+static void __bdx_vlan_rx_vid(struct net_device *ndev, uint16_t vid, int enable)
+{
+ struct bdx_priv *priv = netdev_priv(ndev);
+ u32 reg, bit, val;
+
+ ENTER;
+ DBG2("vid=%d value=%d\n", (int)vid, enable);
+ if (unlikely(vid >= 4096)) {
+ pr_err("invalid VID: %u (> 4096)\n", vid);
+ RET();
+ }
+ reg = regVLAN_0 + (vid / 32) * 4;
+ bit = 1 << vid % 32;
+ val = READ_REG(priv, reg);
+ DBG2("reg=%x, val=%x, bit=%d\n", reg, val, bit);
+ if (enable)
+ val |= bit;
+ else
+ val &= ~bit;
+ DBG2("new val %x\n", val);
+ WRITE_REG(priv, reg, val);
+ RET();
+}
+
+/**
+ * bdx_vlan_rx_add_vid - kernel hook for adding VLAN vid to hw filtering table
+ * @ndev: network device
+ * @vid: VLAN vid to add
+ */
+static int bdx_vlan_rx_add_vid(struct net_device *ndev, __be16 proto, u16 vid)
+{
+ __bdx_vlan_rx_vid(ndev, vid, 1);
+ return 0;
+}
+
+/**
+ * bdx_vlan_rx_kill_vid - kernel hook for killing VLAN vid in hw filtering table
+ * @ndev: network device
+ * @vid: VLAN vid to kill
+ */
+static int bdx_vlan_rx_kill_vid(struct net_device *ndev, __be16 proto, u16 vid)
+{
+ __bdx_vlan_rx_vid(ndev, vid, 0);
+ return 0;
+}
+
+/**
+ * bdx_change_mtu - Change the Maximum Transfer Unit
+ * @netdev: network interface device structure
+ * @new_mtu: new value for maximum frame size
+ *
+ * Returns 0 on success, negative on failure
+ */
+static int bdx_change_mtu(struct net_device *ndev, int new_mtu)
+{
+ ENTER;
+
+ if (new_mtu == ndev->mtu)
+ RET(0);
+
+ /* enforce minimum frame size */
+ if (new_mtu < ETH_ZLEN) {
+ netdev_err(ndev, "mtu %d is less then minimal %d\n",
+ new_mtu, ETH_ZLEN);
+ RET(-EINVAL);
+ }
+
+ ndev->mtu = new_mtu;
+ if (netif_running(ndev)) {
+ bdx_close(ndev);
+ bdx_open(ndev);
+ }
+ RET(0);
+}
+
+static void bdx_setmulti(struct net_device *ndev)
+{
+ struct bdx_priv *priv = netdev_priv(ndev);
+
+ u32 rxf_val =
+ GMAC_RX_FILTER_AM | GMAC_RX_FILTER_AB | GMAC_RX_FILTER_OSEN;
+ int i;
+
+ ENTER;
+ /* IMF - imperfect (hash) rx multicat filter */
+ /* PMF - perfect rx multicat filter */
+
+ /* FIXME: RXE(OFF) */
+ if (ndev->flags & IFF_PROMISC) {
+ rxf_val |= GMAC_RX_FILTER_PRM;
+ } else if (ndev->flags & IFF_ALLMULTI) {
+ /* set IMF to accept all multicast frmaes */
+ for (i = 0; i < MAC_MCST_HASH_NUM; i++)
+ WRITE_REG(priv, regRX_MCST_HASH0 + i * 4, ~0);
+ } else if (!netdev_mc_empty(ndev)) {
+ u8 hash;
+ struct netdev_hw_addr *ha;
+ u32 reg, val;
+
+ /* set IMF to deny all multicast frames */
+ for (i = 0; i < MAC_MCST_HASH_NUM; i++)
+ WRITE_REG(priv, regRX_MCST_HASH0 + i * 4, 0);
+ /* set PMF to deny all multicast frames */
+ for (i = 0; i < MAC_MCST_NUM; i++) {
+ WRITE_REG(priv, regRX_MAC_MCST0 + i * 8, 0);
+ WRITE_REG(priv, regRX_MAC_MCST1 + i * 8, 0);
+ }
+
+ /* use PMF to accept first MAC_MCST_NUM (15) addresses */
+ /* TBD: sort addresses and write them in ascending order
+ * into RX_MAC_MCST regs. we skip this phase now and accept ALL
+ * multicast frames throu IMF */
+ /* accept the rest of addresses throu IMF */
+ netdev_for_each_mc_addr(ha, ndev) {
+ hash = 0;
+ for (i = 0; i < ETH_ALEN; i++)
+ hash ^= ha->addr[i];
+ reg = regRX_MCST_HASH0 + ((hash >> 5) << 2);
+ val = READ_REG(priv, reg);
+ val |= (1 << (hash % 32));
+ WRITE_REG(priv, reg, val);
+ }
+
+ } else {
+ DBG("only own mac %d\n", netdev_mc_count(ndev));
+ rxf_val |= GMAC_RX_FILTER_AB;
+ }
+ WRITE_REG(priv, regGMAC_RXF_A, rxf_val);
+ /* enable RX */
+ /* FIXME: RXE(ON) */
+ RET();
+}
+
+static int bdx_set_mac(struct net_device *ndev, void *p)
+{
+ struct bdx_priv *priv = netdev_priv(ndev);
+ struct sockaddr *addr = p;
+
+ ENTER;
+ /*
+ if (netif_running(dev))
+ return -EBUSY
+ */
+ memcpy(ndev->dev_addr, addr->sa_data, ndev->addr_len);
+ bdx_restore_mac(ndev, priv);
+ RET(0);
+}
+
+static int bdx_read_mac(struct bdx_priv *priv)
+{
+ u16 macAddress[3], i;
+ ENTER;
+
+ macAddress[2] = READ_REG(priv, regUNC_MAC0_A);
+ macAddress[2] = READ_REG(priv, regUNC_MAC0_A);
+ macAddress[1] = READ_REG(priv, regUNC_MAC1_A);
+ macAddress[1] = READ_REG(priv, regUNC_MAC1_A);
+ macAddress[0] = READ_REG(priv, regUNC_MAC2_A);
+ macAddress[0] = READ_REG(priv, regUNC_MAC2_A);
+ for (i = 0; i < 3; i++) {
+ priv->ndev->dev_addr[i * 2 + 1] = macAddress[i];
+ priv->ndev->dev_addr[i * 2] = macAddress[i] >> 8;
+ }
+ RET(0);
+}
+
+static u64 bdx_read_l2stat(struct bdx_priv *priv, int reg)
+{
+ u64 val;
+
+ val = READ_REG(priv, reg);
+ val |= ((u64) READ_REG(priv, reg + 8)) << 32;
+ return val;
+}
+
+/*Do the statistics-update work*/
+static void bdx_update_stats(struct bdx_priv *priv)
+{
+ struct bdx_stats *stats = &priv->hw_stats;
+ u64 *stats_vector = (u64 *) stats;
+ int i;
+ int addr;
+
+ /*Fill HW structure */
+ addr = 0x7200;
+ /*First 12 statistics - 0x7200 - 0x72B0 */
+ for (i = 0; i < 12; i++) {
+ stats_vector[i] = bdx_read_l2stat(priv, addr);
+ addr += 0x10;
+ }
+ BDX_ASSERT(addr != 0x72C0);
+ /* 0x72C0-0x72E0 RSRV */
+ addr = 0x72F0;
+ for (; i < 16; i++) {
+ stats_vector[i] = bdx_read_l2stat(priv, addr);
+ addr += 0x10;
+ }
+ BDX_ASSERT(addr != 0x7330);
+ /* 0x7330-0x7360 RSRV */
+ addr = 0x7370;
+ for (; i < 19; i++) {
+ stats_vector[i] = bdx_read_l2stat(priv, addr);
+ addr += 0x10;
+ }
+ BDX_ASSERT(addr != 0x73A0);
+ /* 0x73A0-0x73B0 RSRV */
+ addr = 0x73C0;
+ for (; i < 23; i++) {
+ stats_vector[i] = bdx_read_l2stat(priv, addr);
+ addr += 0x10;
+ }
+ BDX_ASSERT(addr != 0x7400);
+ BDX_ASSERT((sizeof(struct bdx_stats) / sizeof(u64)) != i);
+}
+
+static void print_rxdd(struct rxd_desc *rxdd, u32 rxd_val1, u16 len,
+ u16 rxd_vlan);
+static void print_rxfd(struct rxf_desc *rxfd);
+
+/*************************************************************************
+ * Rx DB *
+ *************************************************************************/
+
+static void bdx_rxdb_destroy(struct rxdb *db)
+{
+ vfree(db);
+}
+
+static struct rxdb *bdx_rxdb_create(int nelem)
+{
+ struct rxdb *db;
+ int i;
+
+ db = vmalloc(sizeof(struct rxdb)
+ + (nelem * sizeof(int))
+ + (nelem * sizeof(struct rx_map)));
+ if (likely(db != NULL)) {
+ db->stack = (int *)(db + 1);
+ db->elems = (void *)(db->stack + nelem);
+ db->nelem = nelem;
+ db->top = nelem;
+ for (i = 0; i < nelem; i++)
+ db->stack[i] = nelem - i - 1; /* to make first allocs
+ close to db struct*/
+ }
+
+ return db;
+}
+
+static inline int bdx_rxdb_alloc_elem(struct rxdb *db)
+{
+ BDX_ASSERT(db->top <= 0);
+ return db->stack[--(db->top)];
+}
+
+static inline void *bdx_rxdb_addr_elem(struct rxdb *db, int n)
+{
+ BDX_ASSERT((n < 0) || (n >= db->nelem));
+ return db->elems + n;
+}
+
+static inline int bdx_rxdb_available(struct rxdb *db)
+{
+ return db->top;
+}
+
+static inline void bdx_rxdb_free_elem(struct rxdb *db, int n)
+{
+ BDX_ASSERT((n >= db->nelem) || (n < 0));
+ db->stack[(db->top)++] = n;
+}
+
+/*************************************************************************
+ * Rx Init *
+ *************************************************************************/
+
+/**
+ * bdx_rx_init - initialize RX all related HW and SW resources
+ * @priv: NIC private structure
+ *
+ * Returns 0 on success, negative value on failure
+ *
+ * It creates rxf and rxd fifos, update relevant HW registers, preallocate
+ * skb for rx. It assumes that Rx is desabled in HW
+ * funcs are grouped for better cache usage
+ *
+ * RxD fifo is smaller than RxF fifo by design. Upon high load, RxD will be
+ * filled and packets will be dropped by nic without getting into host or
+ * cousing interrupt. Anyway, in that condition, host has no chance to process
+ * all packets, but dropping in nic is cheaper, since it takes 0 cpu cycles
+ */
+
+/* TBD: ensure proper packet size */
+
+static int bdx_rx_init(struct bdx_priv *priv)
+{
+ ENTER;
+
+ if (bdx_fifo_init(priv, &priv->rxd_fifo0.m, priv->rxd_size,
+ regRXD_CFG0_0, regRXD_CFG1_0,
+ regRXD_RPTR_0, regRXD_WPTR_0))
+ goto err_mem;
+ if (bdx_fifo_init(priv, &priv->rxf_fifo0.m, priv->rxf_size,
+ regRXF_CFG0_0, regRXF_CFG1_0,
+ regRXF_RPTR_0, regRXF_WPTR_0))
+ goto err_mem;
+ priv->rxdb = bdx_rxdb_create(priv->rxf_fifo0.m.memsz /
+ sizeof(struct rxf_desc));
+ if (!priv->rxdb)
+ goto err_mem;
+
+ priv->rxf_fifo0.m.pktsz = priv->ndev->mtu + VLAN_ETH_HLEN;
+ return 0;
+
+err_mem:
+ netdev_err(priv->ndev, "Rx init failed\n");
+ return -ENOMEM;
+}
+
+/**
+ * bdx_rx_free_skbs - frees and unmaps all skbs allocated for the fifo
+ * @priv: NIC private structure
+ * @f: RXF fifo
+ */
+static void bdx_rx_free_skbs(struct bdx_priv *priv, struct rxf_fifo *f)
+{
+ struct rx_map *dm;
+ struct rxdb *db = priv->rxdb;
+ u16 i;
+
+ ENTER;
+ DBG("total=%d free=%d busy=%d\n", db->nelem, bdx_rxdb_available(db),
+ db->nelem - bdx_rxdb_available(db));
+ while (bdx_rxdb_available(db) > 0) {
+ i = bdx_rxdb_alloc_elem(db);
+ dm = bdx_rxdb_addr_elem(db, i);
+ dm->dma = 0;
+ }
+ for (i = 0; i < db->nelem; i++) {
+ dm = bdx_rxdb_addr_elem(db, i);
+ if (dm->dma) {
+ pci_unmap_single(priv->pdev,
+ dm->dma, f->m.pktsz,
+ PCI_DMA_FROMDEVICE);
+ dev_kfree_skb(dm->skb);
+ }
+ }
+}
+
+/**
+ * bdx_rx_free - release all Rx resources
+ * @priv: NIC private structure
+ *
+ * It assumes that Rx is desabled in HW
+ */
+static void bdx_rx_free(struct bdx_priv *priv)
+{
+ ENTER;
+ if (priv->rxdb) {
+ bdx_rx_free_skbs(priv, &priv->rxf_fifo0);
+ bdx_rxdb_destroy(priv->rxdb);
+ priv->rxdb = NULL;
+ }
+ bdx_fifo_free(priv, &priv->rxf_fifo0.m);
+ bdx_fifo_free(priv, &priv->rxd_fifo0.m);
+
+ RET();
+}
+
+/*************************************************************************
+ * Rx Engine *
+ *************************************************************************/
+
+/**
+ * bdx_rx_alloc_skbs - fill rxf fifo with new skbs
+ * @priv: nic's private structure
+ * @f: RXF fifo that needs skbs
+ *
+ * It allocates skbs, build rxf descs and push it (rxf descr) into rxf fifo.
+ * skb's virtual and physical addresses are stored in skb db.
+ * To calculate free space, func uses cached values of RPTR and WPTR
+ * When needed, it also updates RPTR and WPTR.
+ */
+
+/* TBD: do not update WPTR if no desc were written */
+
+static void bdx_rx_alloc_skbs(struct bdx_priv *priv, struct rxf_fifo *f)
+{
+ struct sk_buff *skb;
+ struct rxf_desc *rxfd;
+ struct rx_map *dm;
+ int dno, delta, idx;
+ struct rxdb *db = priv->rxdb;
+
+ ENTER;
+ dno = bdx_rxdb_available(db) - 1;
+ while (dno > 0) {
+ skb = netdev_alloc_skb(priv->ndev, f->m.pktsz + NET_IP_ALIGN);
+ if (!skb)
+ break;
+
+ skb_reserve(skb, NET_IP_ALIGN);
+
+ idx = bdx_rxdb_alloc_elem(db);
+ dm = bdx_rxdb_addr_elem(db, idx);
+ dm->dma = pci_map_single(priv->pdev,
+ skb->data, f->m.pktsz,
+ PCI_DMA_FROMDEVICE);
+ dm->skb = skb;
+ rxfd = (struct rxf_desc *)(f->m.va + f->m.wptr);
+ rxfd->info = CPU_CHIP_SWAP32(0x10003); /* INFO=1 BC=3 */
+ rxfd->va_lo = idx;
+ rxfd->pa_lo = CPU_CHIP_SWAP32(L32_64(dm->dma));
+ rxfd->pa_hi = CPU_CHIP_SWAP32(H32_64(dm->dma));
+ rxfd->len = CPU_CHIP_SWAP32(f->m.pktsz);
+ print_rxfd(rxfd);
+
+ f->m.wptr += sizeof(struct rxf_desc);
+ delta = f->m.wptr - f->m.memsz;
+ if (unlikely(delta >= 0)) {
+ f->m.wptr = delta;
+ if (delta > 0) {
+ memcpy(f->m.va, f->m.va + f->m.memsz, delta);
+ DBG("wrapped descriptor\n");
+ }
+ }
+ dno--;
+ }
+ /*TBD: to do - delayed rxf wptr like in txd */
+ WRITE_REG(priv, f->m.reg_WPTR, f->m.wptr & TXF_WPTR_WR_PTR);
+ RET();
+}
+
+static inline void
+NETIF_RX_MUX(struct bdx_priv *priv, u32 rxd_val1, u16 rxd_vlan,
+ struct sk_buff *skb)
+{
+ ENTER;
+ DBG("rxdd->flags.bits.vtag=%d\n", GET_RXD_VTAG(rxd_val1));
+ if (GET_RXD_VTAG(rxd_val1)) {
+ DBG("%s: vlan rcv vlan '%x' vtag '%x'\n",
+ priv->ndev->name,
+ GET_RXD_VLAN_ID(rxd_vlan),
+ GET_RXD_VTAG(rxd_val1));
+ __vlan_hwaccel_put_tag(skb, htons(ETH_P_8021Q), GET_RXD_VLAN_TCI(rxd_vlan));
+ }
+ netif_receive_skb(skb);
+}
+
+static void bdx_recycle_skb(struct bdx_priv *priv, struct rxd_desc *rxdd)
+{
+ struct rxf_desc *rxfd;
+ struct rx_map *dm;
+ struct rxf_fifo *f;
+ struct rxdb *db;
+ struct sk_buff *skb;
+ int delta;
+
+ ENTER;
+ DBG("priv=%p rxdd=%p\n", priv, rxdd);
+ f = &priv->rxf_fifo0;
+ db = priv->rxdb;
+ DBG("db=%p f=%p\n", db, f);
+ dm = bdx_rxdb_addr_elem(db, rxdd->va_lo);
+ DBG("dm=%p\n", dm);
+ skb = dm->skb;
+ rxfd = (struct rxf_desc *)(f->m.va + f->m.wptr);
+ rxfd->info = CPU_CHIP_SWAP32(0x10003); /* INFO=1 BC=3 */
+ rxfd->va_lo = rxdd->va_lo;
+ rxfd->pa_lo = CPU_CHIP_SWAP32(L32_64(dm->dma));
+ rxfd->pa_hi = CPU_CHIP_SWAP32(H32_64(dm->dma));
+ rxfd->len = CPU_CHIP_SWAP32(f->m.pktsz);
+ print_rxfd(rxfd);
+
+ f->m.wptr += sizeof(struct rxf_desc);
+ delta = f->m.wptr - f->m.memsz;
+ if (unlikely(delta >= 0)) {
+ f->m.wptr = delta;
+ if (delta > 0) {
+ memcpy(f->m.va, f->m.va + f->m.memsz, delta);
+ DBG("wrapped descriptor\n");
+ }
+ }
+ RET();
+}
+
+/**
+ * bdx_rx_receive - receives full packets from RXD fifo and pass them to OS
+ * NOTE: a special treatment is given to non-continuous descriptors
+ * that start near the end, wraps around and continue at the beginning. a second
+ * part is copied right after the first, and then descriptor is interpreted as
+ * normal. fifo has an extra space to allow such operations
+ * @priv: nic's private structure
+ * @f: RXF fifo that needs skbs
+ * @budget: maximum number of packets to receive
+ */
+
+/* TBD: replace memcpy func call by explicite inline asm */
+
+static int bdx_rx_receive(struct bdx_priv *priv, struct rxd_fifo *f, int budget)
+{
+ struct net_device *ndev = priv->ndev;
+ struct sk_buff *skb, *skb2;
+ struct rxd_desc *rxdd;
+ struct rx_map *dm;
+ struct rxf_fifo *rxf_fifo;
+ int tmp_len, size;
+ int done = 0;
+ int max_done = BDX_MAX_RX_DONE;
+ struct rxdb *db = NULL;
+ /* Unmarshalled descriptor - copy of descriptor in host order */
+ u32 rxd_val1;
+ u16 len;
+ u16 rxd_vlan;
+
+ ENTER;
+ max_done = budget;
+
+ f->m.wptr = READ_REG(priv, f->m.reg_WPTR) & TXF_WPTR_WR_PTR;
+
+ size = f->m.wptr - f->m.rptr;
+ if (size < 0)
+ size = f->m.memsz + size; /* size is negative :-) */
+
+ while (size > 0) {
+
+ rxdd = (struct rxd_desc *)(f->m.va + f->m.rptr);
+ rxd_val1 = CPU_CHIP_SWAP32(rxdd->rxd_val1);
+
+ len = CPU_CHIP_SWAP16(rxdd->len);
+
+ rxd_vlan = CPU_CHIP_SWAP16(rxdd->rxd_vlan);
+
+ print_rxdd(rxdd, rxd_val1, len, rxd_vlan);
+
+ tmp_len = GET_RXD_BC(rxd_val1) << 3;
+ BDX_ASSERT(tmp_len <= 0);
+ size -= tmp_len;
+ if (size < 0) /* test for partially arrived descriptor */
+ break;
+
+ f->m.rptr += tmp_len;
+
+ tmp_len = f->m.rptr - f->m.memsz;
+ if (unlikely(tmp_len >= 0)) {
+ f->m.rptr = tmp_len;
+ if (tmp_len > 0) {
+ DBG("wrapped desc rptr=%d tmp_len=%d\n",
+ f->m.rptr, tmp_len);
+ memcpy(f->m.va + f->m.memsz, f->m.va, tmp_len);
+ }
+ }
+
+ if (unlikely(GET_RXD_ERR(rxd_val1))) {
+ DBG("rxd_err = 0x%x\n", GET_RXD_ERR(rxd_val1));
+ ndev->stats.rx_errors++;
+ bdx_recycle_skb(priv, rxdd);
+ continue;
+ }
+
+ rxf_fifo = &priv->rxf_fifo0;
+ db = priv->rxdb;
+ dm = bdx_rxdb_addr_elem(db, rxdd->va_lo);
+ skb = dm->skb;
+
+ if (len < BDX_COPYBREAK &&
+ (skb2 = netdev_alloc_skb(priv->ndev, len + NET_IP_ALIGN))) {
+ skb_reserve(skb2, NET_IP_ALIGN);
+ /*skb_put(skb2, len); */
+ pci_dma_sync_single_for_cpu(priv->pdev,
+ dm->dma, rxf_fifo->m.pktsz,
+ PCI_DMA_FROMDEVICE);
+ memcpy(skb2->data, skb->data, len);
+ bdx_recycle_skb(priv, rxdd);
+ skb = skb2;
+ } else {
+ pci_unmap_single(priv->pdev,
+ dm->dma, rxf_fifo->m.pktsz,
+ PCI_DMA_FROMDEVICE);
+ bdx_rxdb_free_elem(db, rxdd->va_lo);
+ }
+
+ ndev->stats.rx_bytes += len;
+
+ skb_put(skb, len);
+ skb->protocol = eth_type_trans(skb, ndev);
+
+ /* Non-IP packets aren't checksum-offloaded */
+ if (GET_RXD_PKT_ID(rxd_val1) == 0)
+ skb_checksum_none_assert(skb);
+ else
+ skb->ip_summed = CHECKSUM_UNNECESSARY;
+
+ NETIF_RX_MUX(priv, rxd_val1, rxd_vlan, skb);
+
+ if (++done >= max_done)
+ break;
+ }
+
+ ndev->stats.rx_packets += done;
+
+ /* FIXME: do smth to minimize pci accesses */
+ WRITE_REG(priv, f->m.reg_RPTR, f->m.rptr & TXF_WPTR_WR_PTR);
+
+ bdx_rx_alloc_skbs(priv, &priv->rxf_fifo0);
+
+ RET(done);
+}
+
+/*************************************************************************
+ * Debug / Temprorary Code *
+ *************************************************************************/
+static void print_rxdd(struct rxd_desc *rxdd, u32 rxd_val1, u16 len,
+ u16 rxd_vlan)
+{
+ DBG("ERROR: rxdd bc %d rxfq %d to %d type %d err %d rxp %d pkt_id %d vtag %d len %d vlan_id %d cfi %d prio %d va_lo %d va_hi %d\n",
+ GET_RXD_BC(rxd_val1), GET_RXD_RXFQ(rxd_val1), GET_RXD_TO(rxd_val1),
+ GET_RXD_TYPE(rxd_val1), GET_RXD_ERR(rxd_val1),
+ GET_RXD_RXP(rxd_val1), GET_RXD_PKT_ID(rxd_val1),
+ GET_RXD_VTAG(rxd_val1), len, GET_RXD_VLAN_ID(rxd_vlan),
+ GET_RXD_CFI(rxd_vlan), GET_RXD_PRIO(rxd_vlan), rxdd->va_lo,
+ rxdd->va_hi);
+}
+
+static void print_rxfd(struct rxf_desc *rxfd)
+{
+ DBG("=== RxF desc CHIP ORDER/ENDIANNESS =============\n"
+ "info 0x%x va_lo %u pa_lo 0x%x pa_hi 0x%x len 0x%x\n",
+ rxfd->info, rxfd->va_lo, rxfd->pa_lo, rxfd->pa_hi, rxfd->len);
+}
+
+/*
+ * TX HW/SW interaction overview
+ * ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+ * There are 2 types of TX communication channels between driver and NIC.
+ * 1) TX Free Fifo - TXF - holds ack descriptors for sent packets
+ * 2) TX Data Fifo - TXD - holds descriptors of full buffers.
+ *
+ * Currently NIC supports TSO, checksuming and gather DMA
+ * UFO and IP fragmentation is on the way
+ *
+ * RX SW Data Structures
+ * ~~~~~~~~~~~~~~~~~~~~~
+ * txdb - used to keep track of all skbs owned by SW and their dma addresses.
+ * For TX case, ownership lasts from geting packet via hard_xmit and until HW
+ * acknowledges sent by TXF descriptors.
+ * Implemented as cyclic buffer.
+ * fifo - keeps info about fifo's size and location, relevant HW registers,
+ * usage and skb db. Each RXD and RXF Fifo has its own fifo structure.
+ * Implemented as simple struct.
+ *
+ * TX SW Execution Flow
+ * ~~~~~~~~~~~~~~~~~~~~
+ * OS calls driver's hard_xmit method with packet to sent.
+ * Driver creates DMA mappings, builds TXD descriptors and kicks HW
+ * by updating TXD WPTR.
+ * When packet is sent, HW write us TXF descriptor and SW frees original skb.
+ * To prevent TXD fifo overflow without reading HW registers every time,
+ * SW deploys "tx level" technique.
+ * Upon strart up, tx level is initialized to TXD fifo length.
+ * For every sent packet, SW gets its TXD descriptor sizei
+ * (from precalculated array) and substructs it from tx level.
+ * The size is also stored in txdb. When TXF ack arrives, SW fetch size of
+ * original TXD descriptor from txdb and adds it to tx level.
+ * When Tx level drops under some predefined treshhold, the driver
+ * stops the TX queue. When TX level rises above that level,
+ * the tx queue is enabled again.
+ *
+ * This technique avoids eccessive reading of RPTR and WPTR registers.
+ * As our benchmarks shows, it adds 1.5 Gbit/sec to NIS's throuput.
+ */
+
+/*************************************************************************
+ * Tx DB *
+ *************************************************************************/
+static inline int bdx_tx_db_size(struct txdb *db)
+{
+ int taken = db->wptr - db->rptr;
+ if (taken < 0)
+ taken = db->size + 1 + taken; /* (size + 1) equals memsz */
+
+ return db->size - taken;
+}
+
+/**
+ * __bdx_tx_db_ptr_next - helper function, increment read/write pointer + wrap
+ * @db: tx data base
+ * @pptr: read or write pointer
+ */
+static inline void __bdx_tx_db_ptr_next(struct txdb *db, struct tx_map **pptr)
+{
+ BDX_ASSERT(db == NULL || pptr == NULL); /* sanity */
+
+ BDX_ASSERT(*pptr != db->rptr && /* expect either read */
+ *pptr != db->wptr); /* or write pointer */
+
+ BDX_ASSERT(*pptr < db->start || /* pointer has to be */
+ *pptr >= db->end); /* in range */
+
+ ++*pptr;
+ if (unlikely(*pptr == db->end))
+ *pptr = db->start;
+}
+
+/**
+ * bdx_tx_db_inc_rptr - increment read pointer
+ * @db: tx data base
+ */
+static inline void bdx_tx_db_inc_rptr(struct txdb *db)
+{
+ BDX_ASSERT(db->rptr == db->wptr); /* can't read from empty db */
+ __bdx_tx_db_ptr_next(db, &db->rptr);
+}
+
+/**
+ * bdx_tx_db_inc_wptr - increment write pointer
+ * @db: tx data base
+ */
+static inline void bdx_tx_db_inc_wptr(struct txdb *db)
+{
+ __bdx_tx_db_ptr_next(db, &db->wptr);
+ BDX_ASSERT(db->rptr == db->wptr); /* we can not get empty db as
+ a result of write */
+}
+
+/**
+ * bdx_tx_db_init - creates and initializes tx db
+ * @d: tx data base
+ * @sz_type: size of tx fifo
+ *
+ * Returns 0 on success, error code otherwise
+ */
+static int bdx_tx_db_init(struct txdb *d, int sz_type)
+{
+ int memsz = FIFO_SIZE * (1 << (sz_type + 1));
+
+ d->start = vmalloc(memsz);
+ if (!d->start)
+ return -ENOMEM;
+
+ /*
+ * In order to differentiate between db is empty and db is full
+ * states at least one element should always be empty in order to
+ * avoid rptr == wptr which means db is empty
+ */
+ d->size = memsz / sizeof(struct tx_map) - 1;
+ d->end = d->start + d->size + 1; /* just after last element */
+
+ /* all dbs are created equally empty */
+ d->rptr = d->start;
+ d->wptr = d->start;
+
+ return 0;
+}
+
+/**
+ * bdx_tx_db_close - closes tx db and frees all memory
+ * @d: tx data base
+ */
+static void bdx_tx_db_close(struct txdb *d)
+{
+ BDX_ASSERT(d == NULL);
+
+ vfree(d->start);
+ d->start = NULL;
+}
+
+/*************************************************************************
+ * Tx Engine *
+ *************************************************************************/
+
+/* sizes of tx desc (including padding if needed) as function
+ * of skb's frag number */
+static struct {
+ u16 bytes;
+ u16 qwords; /* qword = 64 bit */
+} txd_sizes[MAX_SKB_FRAGS + 1];
+
+/**
+ * bdx_tx_map_skb - creates and stores dma mappings for skb's data blocks
+ * @priv: NIC private structure
+ * @skb: socket buffer to map
+ * @txdd: TX descriptor to use
+ *
+ * It makes dma mappings for skb's data blocks and writes them to PBL of
+ * new tx descriptor. It also stores them in the tx db, so they could be
+ * unmaped after data was sent. It is reponsibility of a caller to make
+ * sure that there is enough space in the tx db. Last element holds pointer
+ * to skb itself and marked with zero length
+ */
+static inline void
+bdx_tx_map_skb(struct bdx_priv *priv, struct sk_buff *skb,
+ struct txd_desc *txdd)
+{
+ struct txdb *db = &priv->txdb;
+ struct pbl *pbl = &txdd->pbl[0];
+ int nr_frags = skb_shinfo(skb)->nr_frags;
+ int i;
+
+ db->wptr->len = skb_headlen(skb);
+ db->wptr->addr.dma = pci_map_single(priv->pdev, skb->data,
+ db->wptr->len, PCI_DMA_TODEVICE);
+ pbl->len = CPU_CHIP_SWAP32(db->wptr->len);
+ pbl->pa_lo = CPU_CHIP_SWAP32(L32_64(db->wptr->addr.dma));
+ pbl->pa_hi = CPU_CHIP_SWAP32(H32_64(db->wptr->addr.dma));
+ DBG("=== pbl len: 0x%x ================\n", pbl->len);
+ DBG("=== pbl pa_lo: 0x%x ================\n", pbl->pa_lo);
+ DBG("=== pbl pa_hi: 0x%x ================\n", pbl->pa_hi);
+ bdx_tx_db_inc_wptr(db);
+
+ for (i = 0; i < nr_frags; i++) {
+ const struct skb_frag_struct *frag;
+
+ frag = &skb_shinfo(skb)->frags[i];
+ db->wptr->len = skb_frag_size(frag);
+ db->wptr->addr.dma = skb_frag_dma_map(&priv->pdev->dev, frag,
+ 0, skb_frag_size(frag),
+ DMA_TO_DEVICE);
+
+ pbl++;
+ pbl->len = CPU_CHIP_SWAP32(db->wptr->len);
+ pbl->pa_lo = CPU_CHIP_SWAP32(L32_64(db->wptr->addr.dma));
+ pbl->pa_hi = CPU_CHIP_SWAP32(H32_64(db->wptr->addr.dma));
+ bdx_tx_db_inc_wptr(db);
+ }
+
+ /* add skb clean up info. */
+ db->wptr->len = -txd_sizes[nr_frags].bytes;
+ db->wptr->addr.skb = skb;
+ bdx_tx_db_inc_wptr(db);
+}
+
+/* init_txd_sizes - precalculate sizes of descriptors for skbs up to 16 frags
+ * number of frags is used as index to fetch correct descriptors size,
+ * instead of calculating it each time */
+static void __init init_txd_sizes(void)
+{
+ int i, lwords;
+
+ /* 7 - is number of lwords in txd with one phys buffer
+ * 3 - is number of lwords used for every additional phys buffer */
+ for (i = 0; i < MAX_SKB_FRAGS + 1; i++) {
+ lwords = 7 + (i * 3);
+ if (lwords & 1)
+ lwords++; /* pad it with 1 lword */
+ txd_sizes[i].qwords = lwords >> 1;
+ txd_sizes[i].bytes = lwords << 2;
+ }
+}
+
+/* bdx_tx_init - initialize all Tx related stuff.
+ * Namely, TXD and TXF fifos, database etc */
+static int bdx_tx_init(struct bdx_priv *priv)
+{
+ if (bdx_fifo_init(priv, &priv->txd_fifo0.m, priv->txd_size,
+ regTXD_CFG0_0,
+ regTXD_CFG1_0, regTXD_RPTR_0, regTXD_WPTR_0))
+ goto err_mem;
+ if (bdx_fifo_init(priv, &priv->txf_fifo0.m, priv->txf_size,
+ regTXF_CFG0_0,
+ regTXF_CFG1_0, regTXF_RPTR_0, regTXF_WPTR_0))
+ goto err_mem;
+
+ /* The TX db has to keep mappings for all packets sent (on TxD)
+ * and not yet reclaimed (on TxF) */
+ if (bdx_tx_db_init(&priv->txdb, max(priv->txd_size, priv->txf_size)))
+ goto err_mem;
+
+ priv->tx_level = BDX_MAX_TX_LEVEL;
+#ifdef BDX_DELAY_WPTR
+ priv->tx_update_mark = priv->tx_level - 1024;
+#endif
+ return 0;
+
+err_mem:
+ netdev_err(priv->ndev, "Tx init failed\n");
+ return -ENOMEM;
+}
+
+/**
+ * bdx_tx_space - calculates available space in TX fifo
+ * @priv: NIC private structure
+ *
+ * Returns available space in TX fifo in bytes
+ */
+static inline int bdx_tx_space(struct bdx_priv *priv)
+{
+ struct txd_fifo *f = &priv->txd_fifo0;
+ int fsize;
+
+ f->m.rptr = READ_REG(priv, f->m.reg_RPTR) & TXF_WPTR_WR_PTR;
+ fsize = f->m.rptr - f->m.wptr;
+ if (fsize <= 0)
+ fsize = f->m.memsz + fsize;
+ return fsize;
+}
+
+/**
+ * bdx_tx_transmit - send packet to NIC
+ * @skb: packet to send
+ * @ndev: network device assigned to NIC
+ * Return codes:
+ * o NETDEV_TX_OK everything ok.
+ * o NETDEV_TX_BUSY Cannot transmit packet, try later
+ * Usually a bug, means queue start/stop flow control is broken in
+ * the driver. Note: the driver must NOT put the skb in its DMA ring.
+ * o NETDEV_TX_LOCKED Locking failed, please retry quickly.
+ */
+static netdev_tx_t bdx_tx_transmit(struct sk_buff *skb,
+ struct net_device *ndev)
+{
+ struct bdx_priv *priv = netdev_priv(ndev);
+ struct txd_fifo *f = &priv->txd_fifo0;
+ int txd_checksum = 7; /* full checksum */
+ int txd_lgsnd = 0;
+ int txd_vlan_id = 0;
+ int txd_vtag = 0;
+ int txd_mss = 0;
+
+ int nr_frags = skb_shinfo(skb)->nr_frags;
+ struct txd_desc *txdd;
+ int len;
+ unsigned long flags;
+
+ ENTER;
+
+ spin_lock_irqsave(&priv->tx_lock, flags);
+
+ /* build tx descriptor */
+ BDX_ASSERT(f->m.wptr >= f->m.memsz); /* started with valid wptr */
+ txdd = (struct txd_desc *)(f->m.va + f->m.wptr);
+ if (unlikely(skb->ip_summed != CHECKSUM_PARTIAL))
+ txd_checksum = 0;
+
+ if (skb_shinfo(skb)->gso_size) {
+ txd_mss = skb_shinfo(skb)->gso_size;
+ txd_lgsnd = 1;
+ DBG("skb %p skb len %d gso size = %d\n", skb, skb->len,
+ txd_mss);
+ }
+
+ if (skb_vlan_tag_present(skb)) {
+ /*Cut VLAN ID to 12 bits */
+ txd_vlan_id = skb_vlan_tag_get(skb) & BITS_MASK(12);
+ txd_vtag = 1;
+ }
+
+ txdd->length = CPU_CHIP_SWAP16(skb->len);
+ txdd->mss = CPU_CHIP_SWAP16(txd_mss);
+ txdd->txd_val1 =
+ CPU_CHIP_SWAP32(TXD_W1_VAL
+ (txd_sizes[nr_frags].qwords, txd_checksum, txd_vtag,
+ txd_lgsnd, txd_vlan_id));
+ DBG("=== TxD desc =====================\n");
+ DBG("=== w1: 0x%x ================\n", txdd->txd_val1);
+ DBG("=== w2: mss 0x%x len 0x%x\n", txdd->mss, txdd->length);
+
+ bdx_tx_map_skb(priv, skb, txdd);
+
+ /* increment TXD write pointer. In case of
+ fifo wrapping copy reminder of the descriptor
+ to the beginning */
+ f->m.wptr += txd_sizes[nr_frags].bytes;
+ len = f->m.wptr - f->m.memsz;
+ if (unlikely(len >= 0)) {
+ f->m.wptr = len;
+ if (len > 0) {
+ BDX_ASSERT(len > f->m.memsz);
+ memcpy(f->m.va, f->m.va + f->m.memsz, len);
+ }
+ }
+ BDX_ASSERT(f->m.wptr >= f->m.memsz); /* finished with valid wptr */
+
+ priv->tx_level -= txd_sizes[nr_frags].bytes;
+ BDX_ASSERT(priv->tx_level <= 0 || priv->tx_level > BDX_MAX_TX_LEVEL);
+#ifdef BDX_DELAY_WPTR
+ if (priv->tx_level > priv->tx_update_mark) {
+ /* Force memory writes to complete before letting h/w
+ know there are new descriptors to fetch.
+ (might be needed on platforms like IA64)
+ wmb(); */
+ WRITE_REG(priv, f->m.reg_WPTR, f->m.wptr & TXF_WPTR_WR_PTR);
+ } else {
+ if (priv->tx_noupd++ > BDX_NO_UPD_PACKETS) {
+ priv->tx_noupd = 0;
+ WRITE_REG(priv, f->m.reg_WPTR,
+ f->m.wptr & TXF_WPTR_WR_PTR);
+ }
+ }
+#else
+ /* Force memory writes to complete before letting h/w
+ know there are new descriptors to fetch.
+ (might be needed on platforms like IA64)
+ wmb(); */
+ WRITE_REG(priv, f->m.reg_WPTR, f->m.wptr & TXF_WPTR_WR_PTR);
+
+#endif
+#ifdef BDX_LLTX
+ ndev->trans_start = jiffies; /* NETIF_F_LLTX driver :( */
+#endif
+ ndev->stats.tx_packets++;
+ ndev->stats.tx_bytes += skb->len;
+
+ if (priv->tx_level < BDX_MIN_TX_LEVEL) {
+ DBG("%s: %s: TX Q STOP level %d\n",
+ BDX_DRV_NAME, ndev->name, priv->tx_level);
+ netif_stop_queue(ndev);
+ }
+
+ spin_unlock_irqrestore(&priv->tx_lock, flags);
+ return NETDEV_TX_OK;
+}
+
+/**
+ * bdx_tx_cleanup - clean TXF fifo, run in the context of IRQ.
+ * @priv: bdx adapter
+ *
+ * It scans TXF fifo for descriptors, frees DMA mappings and reports to OS
+ * that those packets were sent
+ */
+static void bdx_tx_cleanup(struct bdx_priv *priv)
+{
+ struct txf_fifo *f = &priv->txf_fifo0;
+ struct txdb *db = &priv->txdb;
+ int tx_level = 0;
+
+ ENTER;
+ f->m.wptr = READ_REG(priv, f->m.reg_WPTR) & TXF_WPTR_MASK;
+ BDX_ASSERT(f->m.rptr >= f->m.memsz); /* started with valid rptr */
+
+ while (f->m.wptr != f->m.rptr) {
+ f->m.rptr += BDX_TXF_DESC_SZ;
+ f->m.rptr &= f->m.size_mask;
+
+ /* unmap all the fragments */
+ /* first has to come tx_maps containing dma */
+ BDX_ASSERT(db->rptr->len == 0);
+ do {
+ BDX_ASSERT(db->rptr->addr.dma == 0);
+ pci_unmap_page(priv->pdev, db->rptr->addr.dma,
+ db->rptr->len, PCI_DMA_TODEVICE);
+ bdx_tx_db_inc_rptr(db);
+ } while (db->rptr->len > 0);
+ tx_level -= db->rptr->len; /* '-' koz len is negative */
+
+ /* now should come skb pointer - free it */
+ dev_kfree_skb_irq(db->rptr->addr.skb);
+ bdx_tx_db_inc_rptr(db);
+ }
+
+ /* let h/w know which TXF descriptors were cleaned */
+ BDX_ASSERT((f->m.wptr & TXF_WPTR_WR_PTR) >= f->m.memsz);
+ WRITE_REG(priv, f->m.reg_RPTR, f->m.rptr & TXF_WPTR_WR_PTR);
+
+ /* We reclaimed resources, so in case the Q is stopped by xmit callback,
+ * we resume the transmission and use tx_lock to synchronize with xmit.*/
+ spin_lock(&priv->tx_lock);
+ priv->tx_level += tx_level;
+ BDX_ASSERT(priv->tx_level <= 0 || priv->tx_level > BDX_MAX_TX_LEVEL);
+#ifdef BDX_DELAY_WPTR
+ if (priv->tx_noupd) {
+ priv->tx_noupd = 0;
+ WRITE_REG(priv, priv->txd_fifo0.m.reg_WPTR,
+ priv->txd_fifo0.m.wptr & TXF_WPTR_WR_PTR);
+ }
+#endif
+
+ if (unlikely(netif_queue_stopped(priv->ndev) &&
+ netif_carrier_ok(priv->ndev) &&
+ (priv->tx_level >= BDX_MIN_TX_LEVEL))) {
+ DBG("%s: %s: TX Q WAKE level %d\n",
+ BDX_DRV_NAME, priv->ndev->name, priv->tx_level);
+ netif_wake_queue(priv->ndev);
+ }
+ spin_unlock(&priv->tx_lock);
+}
+
+/**
+ * bdx_tx_free_skbs - frees all skbs from TXD fifo.
+ * It gets called when OS stops this dev, eg upon "ifconfig down" or rmmod
+ */
+static void bdx_tx_free_skbs(struct bdx_priv *priv)
+{
+ struct txdb *db = &priv->txdb;
+
+ ENTER;
+ while (db->rptr != db->wptr) {
+ if (likely(db->rptr->len))
+ pci_unmap_page(priv->pdev, db->rptr->addr.dma,
+ db->rptr->len, PCI_DMA_TODEVICE);
+ else
+ dev_kfree_skb(db->rptr->addr.skb);
+ bdx_tx_db_inc_rptr(db);
+ }
+ RET();
+}
+
+/* bdx_tx_free - frees all Tx resources */
+static void bdx_tx_free(struct bdx_priv *priv)
+{
+ ENTER;
+ bdx_tx_free_skbs(priv);
+ bdx_fifo_free(priv, &priv->txd_fifo0.m);
+ bdx_fifo_free(priv, &priv->txf_fifo0.m);
+ bdx_tx_db_close(&priv->txdb);
+}
+
+/**
+ * bdx_tx_push_desc - push descriptor to TxD fifo
+ * @priv: NIC private structure
+ * @data: desc's data
+ * @size: desc's size
+ *
+ * Pushes desc to TxD fifo and overlaps it if needed.
+ * NOTE: this func does not check for available space. this is responsibility
+ * of the caller. Neither does it check that data size is smaller than
+ * fifo size.
+ */
+static void bdx_tx_push_desc(struct bdx_priv *priv, void *data, int size)
+{
+ struct txd_fifo *f = &priv->txd_fifo0;
+ int i = f->m.memsz - f->m.wptr;
+
+ if (size == 0)
+ return;
+
+ if (i > size) {
+ memcpy(f->m.va + f->m.wptr, data, size);
+ f->m.wptr += size;
+ } else {
+ memcpy(f->m.va + f->m.wptr, data, i);
+ f->m.wptr = size - i;
+ memcpy(f->m.va, data + i, f->m.wptr);
+ }
+ WRITE_REG(priv, f->m.reg_WPTR, f->m.wptr & TXF_WPTR_WR_PTR);
+}
+
+/**
+ * bdx_tx_push_desc_safe - push descriptor to TxD fifo in a safe way
+ * @priv: NIC private structure
+ * @data: desc's data
+ * @size: desc's size
+ *
+ * NOTE: this func does check for available space and, if necessary, waits for
+ * NIC to read existing data before writing new one.
+ */
+static void bdx_tx_push_desc_safe(struct bdx_priv *priv, void *data, int size)
+{
+ int timer = 0;
+ ENTER;
+
+ while (size > 0) {
+ /* we substruct 8 because when fifo is full rptr == wptr
+ which also means that fifo is empty, we can understand
+ the difference, but could hw do the same ??? :) */
+ int avail = bdx_tx_space(priv) - 8;
+ if (avail <= 0) {
+ if (timer++ > 300) { /* prevent endless loop */
+ DBG("timeout while writing desc to TxD fifo\n");
+ break;
+ }
+ udelay(50); /* give hw a chance to clean fifo */
+ continue;
+ }
+ avail = min(avail, size);
+ DBG("about to push %d bytes starting %p size %d\n", avail,
+ data, size);
+ bdx_tx_push_desc(priv, data, avail);
+ size -= avail;
+ data += avail;
+ }
+ RET();
+}
+
+static const struct net_device_ops bdx_netdev_ops = {
+ .ndo_open = bdx_open,
+ .ndo_stop = bdx_close,
+ .ndo_start_xmit = bdx_tx_transmit,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_do_ioctl = bdx_ioctl,
+ .ndo_set_rx_mode = bdx_setmulti,
+ .ndo_change_mtu = bdx_change_mtu,
+ .ndo_set_mac_address = bdx_set_mac,
+ .ndo_vlan_rx_add_vid = bdx_vlan_rx_add_vid,
+ .ndo_vlan_rx_kill_vid = bdx_vlan_rx_kill_vid,
+};
+
+/**
+ * bdx_probe - Device Initialization Routine
+ * @pdev: PCI device information struct
+ * @ent: entry in bdx_pci_tbl
+ *
+ * Returns 0 on success, negative on failure
+ *
+ * bdx_probe initializes an adapter identified by a pci_dev structure.
+ * The OS initialization, configuring of the adapter private structure,
+ * and a hardware reset occur.
+ *
+ * functions and their order used as explained in
+ * /usr/src/linux/Documentation/DMA-{API,mapping}.txt
+ *
+ */
+
+/* TBD: netif_msg should be checked and implemented. I disable it for now */
+static int
+bdx_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
+{
+ struct net_device *ndev;
+ struct bdx_priv *priv;
+ int err, pci_using_dac, port;
+ unsigned long pciaddr;
+ u32 regionSize;
+ struct pci_nic *nic;
+
+ ENTER;
+
+ nic = vmalloc(sizeof(*nic));
+ if (!nic)
+ RET(-ENOMEM);
+
+ /************** pci *****************/
+ err = pci_enable_device(pdev);
+ if (err) /* it triggers interrupt, dunno why. */
+ goto err_pci; /* it's not a problem though */
+
+ if (!(err = pci_set_dma_mask(pdev, DMA_BIT_MASK(64))) &&
+ !(err = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(64)))) {
+ pci_using_dac = 1;
+ } else {
+ if ((err = pci_set_dma_mask(pdev, DMA_BIT_MASK(32))) ||
+ (err = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32)))) {
+ pr_err("No usable DMA configuration, aborting\n");
+ goto err_dma;
+ }
+ pci_using_dac = 0;
+ }
+
+ err = pci_request_regions(pdev, BDX_DRV_NAME);
+ if (err)
+ goto err_dma;
+
+ pci_set_master(pdev);
+
+ pciaddr = pci_resource_start(pdev, 0);
+ if (!pciaddr) {
+ err = -EIO;
+ pr_err("no MMIO resource\n");
+ goto err_out_res;
+ }
+ regionSize = pci_resource_len(pdev, 0);
+ if (regionSize < BDX_REGS_SIZE) {
+ err = -EIO;
+ pr_err("MMIO resource (%x) too small\n", regionSize);
+ goto err_out_res;
+ }
+
+ nic->regs = ioremap(pciaddr, regionSize);
+ if (!nic->regs) {
+ err = -EIO;
+ pr_err("ioremap failed\n");
+ goto err_out_res;
+ }
+
+ if (pdev->irq < 2) {
+ err = -EIO;
+ pr_err("invalid irq (%d)\n", pdev->irq);
+ goto err_out_iomap;
+ }
+ pci_set_drvdata(pdev, nic);
+
+ if (pdev->device == 0x3014)
+ nic->port_num = 2;
+ else
+ nic->port_num = 1;
+
+ print_hw_id(pdev);
+
+ bdx_hw_reset_direct(nic->regs);
+
+ nic->irq_type = IRQ_INTX;
+#ifdef BDX_MSI
+ if ((readl(nic->regs + FPGA_VER) & 0xFFF) >= 378) {
+ err = pci_enable_msi(pdev);
+ if (err)
+ pr_err("Can't eneble msi. error is %d\n", err);
+ else
+ nic->irq_type = IRQ_MSI;
+ } else
+ DBG("HW does not support MSI\n");
+#endif
+
+ /************** netdev **************/
+ for (port = 0; port < nic->port_num; port++) {
+ ndev = alloc_etherdev(sizeof(struct bdx_priv));
+ if (!ndev) {
+ err = -ENOMEM;
+ goto err_out_iomap;
+ }
+
+ ndev->netdev_ops = &bdx_netdev_ops;
+ ndev->tx_queue_len = BDX_NDEV_TXQ_LEN;
+
+ bdx_set_ethtool_ops(ndev); /* ethtool interface */
+
+ /* these fields are used for info purposes only
+ * so we can have them same for all ports of the board */
+ ndev->if_port = port;
+ ndev->features = NETIF_F_IP_CSUM | NETIF_F_SG | NETIF_F_TSO
+ | NETIF_F_HW_VLAN_CTAG_TX | NETIF_F_HW_VLAN_CTAG_RX |
+ NETIF_F_HW_VLAN_CTAG_FILTER | NETIF_F_RXCSUM
+ ;
+ ndev->hw_features = NETIF_F_IP_CSUM | NETIF_F_SG |
+ NETIF_F_TSO | NETIF_F_HW_VLAN_CTAG_TX;
+
+ if (pci_using_dac)
+ ndev->features |= NETIF_F_HIGHDMA;
+
+ /************** priv ****************/
+ priv = nic->priv[port] = netdev_priv(ndev);
+
+ priv->pBdxRegs = nic->regs + port * 0x8000;
+ priv->port = port;
+ priv->pdev = pdev;
+ priv->ndev = ndev;
+ priv->nic = nic;
+ priv->msg_enable = BDX_DEF_MSG_ENABLE;
+
+ netif_napi_add(ndev, &priv->napi, bdx_poll, 64);
+
+ if ((readl(nic->regs + FPGA_VER) & 0xFFF) == 308) {
+ DBG("HW statistics not supported\n");
+ priv->stats_flag = 0;
+ } else {
+ priv->stats_flag = 1;
+ }
+
+ /* Initialize fifo sizes. */
+ priv->txd_size = 2;
+ priv->txf_size = 2;
+ priv->rxd_size = 2;
+ priv->rxf_size = 3;
+
+ /* Initialize the initial coalescing registers. */
+ priv->rdintcm = INT_REG_VAL(0x20, 1, 4, 12);
+ priv->tdintcm = INT_REG_VAL(0x20, 1, 0, 12);
+
+ /* ndev->xmit_lock spinlock is not used.
+ * Private priv->tx_lock is used for synchronization
+ * between transmit and TX irq cleanup. In addition
+ * set multicast list callback has to use priv->tx_lock.
+ */
+#ifdef BDX_LLTX
+ ndev->features |= NETIF_F_LLTX;
+#endif
+ spin_lock_init(&priv->tx_lock);
+
+ /*bdx_hw_reset(priv); */
+ if (bdx_read_mac(priv)) {
+ pr_err("load MAC address failed\n");
+ goto err_out_iomap;
+ }
+ SET_NETDEV_DEV(ndev, &pdev->dev);
+ err = register_netdev(ndev);
+ if (err) {
+ pr_err("register_netdev failed\n");
+ goto err_out_free;
+ }
+ netif_carrier_off(ndev);
+ netif_stop_queue(ndev);
+
+ print_eth_id(ndev);
+ }
+ RET(0);
+
+err_out_free:
+ free_netdev(ndev);
+err_out_iomap:
+ iounmap(nic->regs);
+err_out_res:
+ pci_release_regions(pdev);
+err_dma:
+ pci_disable_device(pdev);
+err_pci:
+ vfree(nic);
+
+ RET(err);
+}
+
+/****************** Ethtool interface *********************/
+/* get strings for statistics counters */
+static const char
+ bdx_stat_names[][ETH_GSTRING_LEN] = {
+ "InUCast", /* 0x7200 */
+ "InMCast", /* 0x7210 */
+ "InBCast", /* 0x7220 */
+ "InPkts", /* 0x7230 */
+ "InErrors", /* 0x7240 */
+ "InDropped", /* 0x7250 */
+ "FrameTooLong", /* 0x7260 */
+ "FrameSequenceErrors", /* 0x7270 */
+ "InVLAN", /* 0x7280 */
+ "InDroppedDFE", /* 0x7290 */
+ "InDroppedIntFull", /* 0x72A0 */
+ "InFrameAlignErrors", /* 0x72B0 */
+
+ /* 0x72C0-0x72E0 RSRV */
+
+ "OutUCast", /* 0x72F0 */
+ "OutMCast", /* 0x7300 */
+ "OutBCast", /* 0x7310 */
+ "OutPkts", /* 0x7320 */
+
+ /* 0x7330-0x7360 RSRV */
+
+ "OutVLAN", /* 0x7370 */
+ "InUCastOctects", /* 0x7380 */
+ "OutUCastOctects", /* 0x7390 */
+
+ /* 0x73A0-0x73B0 RSRV */
+
+ "InBCastOctects", /* 0x73C0 */
+ "OutBCastOctects", /* 0x73D0 */
+ "InOctects", /* 0x73E0 */
+ "OutOctects", /* 0x73F0 */
+};
+
+/*
+ * bdx_get_settings - get device-specific settings
+ * @netdev
+ * @ecmd
+ */
+static int bdx_get_settings(struct net_device *netdev, struct ethtool_cmd *ecmd)
+{
+ u32 rdintcm;
+ u32 tdintcm;
+ struct bdx_priv *priv = netdev_priv(netdev);
+
+ rdintcm = priv->rdintcm;
+ tdintcm = priv->tdintcm;
+
+ ecmd->supported = (SUPPORTED_10000baseT_Full | SUPPORTED_FIBRE);
+ ecmd->advertising = (ADVERTISED_10000baseT_Full | ADVERTISED_FIBRE);
+ ethtool_cmd_speed_set(ecmd, SPEED_10000);
+ ecmd->duplex = DUPLEX_FULL;
+ ecmd->port = PORT_FIBRE;
+ ecmd->transceiver = XCVR_EXTERNAL; /* what does it mean? */
+ ecmd->autoneg = AUTONEG_DISABLE;
+
+ /* PCK_TH measures in multiples of FIFO bytes
+ We translate to packets */
+ ecmd->maxtxpkt =
+ ((GET_PCK_TH(tdintcm) * PCK_TH_MULT) / BDX_TXF_DESC_SZ);
+ ecmd->maxrxpkt =
+ ((GET_PCK_TH(rdintcm) * PCK_TH_MULT) / sizeof(struct rxf_desc));
+
+ return 0;
+}
+
+/*
+ * bdx_get_drvinfo - report driver information
+ * @netdev
+ * @drvinfo
+ */
+static void
+bdx_get_drvinfo(struct net_device *netdev, struct ethtool_drvinfo *drvinfo)
+{
+ struct bdx_priv *priv = netdev_priv(netdev);
+
+ strlcpy(drvinfo->driver, BDX_DRV_NAME, sizeof(drvinfo->driver));
+ strlcpy(drvinfo->version, BDX_DRV_VERSION, sizeof(drvinfo->version));
+ strlcpy(drvinfo->fw_version, "N/A", sizeof(drvinfo->fw_version));
+ strlcpy(drvinfo->bus_info, pci_name(priv->pdev),
+ sizeof(drvinfo->bus_info));
+
+ drvinfo->n_stats = ((priv->stats_flag) ? ARRAY_SIZE(bdx_stat_names) : 0);
+ drvinfo->testinfo_len = 0;
+ drvinfo->regdump_len = 0;
+ drvinfo->eedump_len = 0;
+}
+
+/*
+ * bdx_get_coalesce - get interrupt coalescing parameters
+ * @netdev
+ * @ecoal
+ */
+static int
+bdx_get_coalesce(struct net_device *netdev, struct ethtool_coalesce *ecoal)
+{
+ u32 rdintcm;
+ u32 tdintcm;
+ struct bdx_priv *priv = netdev_priv(netdev);
+
+ rdintcm = priv->rdintcm;
+ tdintcm = priv->tdintcm;
+
+ /* PCK_TH measures in multiples of FIFO bytes
+ We translate to packets */
+ ecoal->rx_coalesce_usecs = GET_INT_COAL(rdintcm) * INT_COAL_MULT;
+ ecoal->rx_max_coalesced_frames =
+ ((GET_PCK_TH(rdintcm) * PCK_TH_MULT) / sizeof(struct rxf_desc));
+
+ ecoal->tx_coalesce_usecs = GET_INT_COAL(tdintcm) * INT_COAL_MULT;
+ ecoal->tx_max_coalesced_frames =
+ ((GET_PCK_TH(tdintcm) * PCK_TH_MULT) / BDX_TXF_DESC_SZ);
+
+ /* adaptive parameters ignored */
+ return 0;
+}
+
+/*
+ * bdx_set_coalesce - set interrupt coalescing parameters
+ * @netdev
+ * @ecoal
+ */
+static int
+bdx_set_coalesce(struct net_device *netdev, struct ethtool_coalesce *ecoal)
+{
+ u32 rdintcm;
+ u32 tdintcm;
+ struct bdx_priv *priv = netdev_priv(netdev);
+ int rx_coal;
+ int tx_coal;
+ int rx_max_coal;
+ int tx_max_coal;
+
+ /* Check for valid input */
+ rx_coal = ecoal->rx_coalesce_usecs / INT_COAL_MULT;
+ tx_coal = ecoal->tx_coalesce_usecs / INT_COAL_MULT;
+ rx_max_coal = ecoal->rx_max_coalesced_frames;
+ tx_max_coal = ecoal->tx_max_coalesced_frames;
+
+ /* Translate from packets to multiples of FIFO bytes */
+ rx_max_coal =
+ (((rx_max_coal * sizeof(struct rxf_desc)) + PCK_TH_MULT - 1)
+ / PCK_TH_MULT);
+ tx_max_coal =
+ (((tx_max_coal * BDX_TXF_DESC_SZ) + PCK_TH_MULT - 1)
+ / PCK_TH_MULT);
+
+ if ((rx_coal > 0x7FFF) || (tx_coal > 0x7FFF) ||
+ (rx_max_coal > 0xF) || (tx_max_coal > 0xF))
+ return -EINVAL;
+
+ rdintcm = INT_REG_VAL(rx_coal, GET_INT_COAL_RC(priv->rdintcm),
+ GET_RXF_TH(priv->rdintcm), rx_max_coal);
+ tdintcm = INT_REG_VAL(tx_coal, GET_INT_COAL_RC(priv->tdintcm), 0,
+ tx_max_coal);
+
+ priv->rdintcm = rdintcm;
+ priv->tdintcm = tdintcm;
+
+ WRITE_REG(priv, regRDINTCM0, rdintcm);
+ WRITE_REG(priv, regTDINTCM0, tdintcm);
+
+ return 0;
+}
+
+/* Convert RX fifo size to number of pending packets */
+static inline int bdx_rx_fifo_size_to_packets(int rx_size)
+{
+ return (FIFO_SIZE * (1 << rx_size)) / sizeof(struct rxf_desc);
+}
+
+/* Convert TX fifo size to number of pending packets */
+static inline int bdx_tx_fifo_size_to_packets(int tx_size)
+{
+ return (FIFO_SIZE * (1 << tx_size)) / BDX_TXF_DESC_SZ;
+}
+
+/*
+ * bdx_get_ringparam - report ring sizes
+ * @netdev
+ * @ring
+ */
+static void
+bdx_get_ringparam(struct net_device *netdev, struct ethtool_ringparam *ring)
+{
+ struct bdx_priv *priv = netdev_priv(netdev);
+
+ /*max_pending - the maximum-sized FIFO we allow */
+ ring->rx_max_pending = bdx_rx_fifo_size_to_packets(3);
+ ring->tx_max_pending = bdx_tx_fifo_size_to_packets(3);
+ ring->rx_pending = bdx_rx_fifo_size_to_packets(priv->rxf_size);
+ ring->tx_pending = bdx_tx_fifo_size_to_packets(priv->txd_size);
+}
+
+/*
+ * bdx_set_ringparam - set ring sizes
+ * @netdev
+ * @ring
+ */
+static int
+bdx_set_ringparam(struct net_device *netdev, struct ethtool_ringparam *ring)
+{
+ struct bdx_priv *priv = netdev_priv(netdev);
+ int rx_size = 0;
+ int tx_size = 0;
+
+ for (; rx_size < 4; rx_size++) {
+ if (bdx_rx_fifo_size_to_packets(rx_size) >= ring->rx_pending)
+ break;
+ }
+ if (rx_size == 4)
+ rx_size = 3;
+
+ for (; tx_size < 4; tx_size++) {
+ if (bdx_tx_fifo_size_to_packets(tx_size) >= ring->tx_pending)
+ break;
+ }
+ if (tx_size == 4)
+ tx_size = 3;
+
+ /*Is there anything to do? */
+ if ((rx_size == priv->rxf_size) &&
+ (tx_size == priv->txd_size))
+ return 0;
+
+ priv->rxf_size = rx_size;
+ if (rx_size > 1)
+ priv->rxd_size = rx_size - 1;
+ else
+ priv->rxd_size = rx_size;
+
+ priv->txf_size = priv->txd_size = tx_size;
+
+ if (netif_running(netdev)) {
+ bdx_close(netdev);
+ bdx_open(netdev);
+ }
+ return 0;
+}
+
+/*
+ * bdx_get_strings - return a set of strings that describe the requested objects
+ * @netdev
+ * @data
+ */
+static void bdx_get_strings(struct net_device *netdev, u32 stringset, u8 *data)
+{
+ switch (stringset) {
+ case ETH_SS_STATS:
+ memcpy(data, *bdx_stat_names, sizeof(bdx_stat_names));
+ break;
+ }
+}
+
+/*
+ * bdx_get_sset_count - return number of statistics or tests
+ * @netdev
+ */
+static int bdx_get_sset_count(struct net_device *netdev, int stringset)
+{
+ struct bdx_priv *priv = netdev_priv(netdev);
+
+ switch (stringset) {
+ case ETH_SS_STATS:
+ BDX_ASSERT(ARRAY_SIZE(bdx_stat_names)
+ != sizeof(struct bdx_stats) / sizeof(u64));
+ return (priv->stats_flag) ? ARRAY_SIZE(bdx_stat_names) : 0;
+ }
+
+ return -EINVAL;
+}
+
+/*
+ * bdx_get_ethtool_stats - return device's hardware L2 statistics
+ * @netdev
+ * @stats
+ * @data
+ */
+static void bdx_get_ethtool_stats(struct net_device *netdev,
+ struct ethtool_stats *stats, u64 *data)
+{
+ struct bdx_priv *priv = netdev_priv(netdev);
+
+ if (priv->stats_flag) {
+
+ /* Update stats from HW */
+ bdx_update_stats(priv);
+
+ /* Copy data to user buffer */
+ memcpy(data, &priv->hw_stats, sizeof(priv->hw_stats));
+ }
+}
+
+/*
+ * bdx_set_ethtool_ops - ethtool interface implementation
+ * @netdev
+ */
+static void bdx_set_ethtool_ops(struct net_device *netdev)
+{
+ static const struct ethtool_ops bdx_ethtool_ops = {
+ .get_settings = bdx_get_settings,
+ .get_drvinfo = bdx_get_drvinfo,
+ .get_link = ethtool_op_get_link,
+ .get_coalesce = bdx_get_coalesce,
+ .set_coalesce = bdx_set_coalesce,
+ .get_ringparam = bdx_get_ringparam,
+ .set_ringparam = bdx_set_ringparam,
+ .get_strings = bdx_get_strings,
+ .get_sset_count = bdx_get_sset_count,
+ .get_ethtool_stats = bdx_get_ethtool_stats,
+ };
+
+ netdev->ethtool_ops = &bdx_ethtool_ops;
+}
+
+/**
+ * bdx_remove - Device Removal Routine
+ * @pdev: PCI device information struct
+ *
+ * bdx_remove is called by the PCI subsystem to alert the driver
+ * that it should release a PCI device. The could be caused by a
+ * Hot-Plug event, or because the driver is going to be removed from
+ * memory.
+ **/
+static void bdx_remove(struct pci_dev *pdev)
+{
+ struct pci_nic *nic = pci_get_drvdata(pdev);
+ struct net_device *ndev;
+ int port;
+
+ for (port = 0; port < nic->port_num; port++) {
+ ndev = nic->priv[port]->ndev;
+ unregister_netdev(ndev);
+ free_netdev(ndev);
+ }
+
+ /*bdx_hw_reset_direct(nic->regs); */
+#ifdef BDX_MSI
+ if (nic->irq_type == IRQ_MSI)
+ pci_disable_msi(pdev);
+#endif
+
+ iounmap(nic->regs);
+ pci_release_regions(pdev);
+ pci_disable_device(pdev);
+ vfree(nic);
+
+ RET();
+}
+
+static struct pci_driver bdx_pci_driver = {
+ .name = BDX_DRV_NAME,
+ .id_table = bdx_pci_tbl,
+ .probe = bdx_probe,
+ .remove = bdx_remove,
+};
+
+/*
+ * print_driver_id - print parameters of the driver build
+ */
+static void __init print_driver_id(void)
+{
+ pr_info("%s, %s\n", BDX_DRV_DESC, BDX_DRV_VERSION);
+ pr_info("Options: hw_csum %s\n", BDX_MSI_STRING);
+}
+
+static int __init bdx_module_init(void)
+{
+ ENTER;
+ init_txd_sizes();
+ print_driver_id();
+ RET(pci_register_driver(&bdx_pci_driver));
+}
+
+module_init(bdx_module_init);
+
+static void __exit bdx_module_exit(void)
+{
+ ENTER;
+ pci_unregister_driver(&bdx_pci_driver);
+ RET();
+}
+
+module_exit(bdx_module_exit);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR(DRIVER_AUTHOR);
+MODULE_DESCRIPTION(BDX_DRV_DESC);
+MODULE_FIRMWARE("tehuti/bdx.bin");
Code Review / kvmfornfv.git / blobdiff