--- /dev/null
+/*
+ * New driver for Marvell Yukon chipset and SysKonnect Gigabit
+ * Ethernet adapters. Based on earlier sk98lin, e100 and
+ * FreeBSD if_sk drivers.
+ *
+ * This driver intentionally does not support all the features
+ * of the original driver such as link fail-over and link management because
+ * those should be done at higher levels.
+ *
+ * Copyright (C) 2004, 2005 Stephen Hemminger <shemminger@osdl.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
+#include <linux/in.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/ethtool.h>
+#include <linux/pci.h>
+#include <linux/if_vlan.h>
+#include <linux/ip.h>
+#include <linux/delay.h>
+#include <linux/crc32.h>
+#include <linux/dma-mapping.h>
+#include <linux/debugfs.h>
+#include <linux/sched.h>
+#include <linux/seq_file.h>
+#include <linux/mii.h>
+#include <linux/slab.h>
+#include <linux/dmi.h>
+#include <linux/prefetch.h>
+#include <asm/irq.h>
+
+#include "skge.h"
+
+#define DRV_NAME "skge"
+#define DRV_VERSION "1.14"
+
+#define DEFAULT_TX_RING_SIZE 128
+#define DEFAULT_RX_RING_SIZE 512
+#define MAX_TX_RING_SIZE 1024
+#define TX_LOW_WATER (MAX_SKB_FRAGS + 1)
+#define MAX_RX_RING_SIZE 4096
+#define RX_COPY_THRESHOLD 128
+#define RX_BUF_SIZE 1536
+#define PHY_RETRIES 1000
+#define ETH_JUMBO_MTU 9000
+#define TX_WATCHDOG (5 * HZ)
+#define NAPI_WEIGHT 64
+#define BLINK_MS 250
+#define LINK_HZ HZ
+
+#define SKGE_EEPROM_MAGIC 0x9933aabb
+
+
+MODULE_DESCRIPTION("SysKonnect Gigabit Ethernet driver");
+MODULE_AUTHOR("Stephen Hemminger <shemminger@linux-foundation.org>");
+MODULE_LICENSE("GPL");
+MODULE_VERSION(DRV_VERSION);
+
+static const u32 default_msg = (NETIF_MSG_DRV | NETIF_MSG_PROBE |
+ NETIF_MSG_LINK | NETIF_MSG_IFUP |
+ NETIF_MSG_IFDOWN);
+
+static int debug = -1; /* defaults above */
+module_param(debug, int, 0);
+MODULE_PARM_DESC(debug, "Debug level (0=none,...,16=all)");
+
+static const struct pci_device_id skge_id_table[] = {
+ { PCI_DEVICE(PCI_VENDOR_ID_3COM, 0x1700) }, /* 3Com 3C940 */
+ { PCI_DEVICE(PCI_VENDOR_ID_3COM, 0x80EB) }, /* 3Com 3C940B */
+#ifdef CONFIG_SKGE_GENESIS
+ { PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, 0x4300) }, /* SK-9xx */
+#endif
+ { PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, 0x4320) }, /* SK-98xx V2.0 */
+ { PCI_DEVICE(PCI_VENDOR_ID_DLINK, 0x4b01) }, /* D-Link DGE-530T (rev.B) */
+ { PCI_DEVICE(PCI_VENDOR_ID_DLINK, 0x4c00) }, /* D-Link DGE-530T */
+ { PCI_DEVICE(PCI_VENDOR_ID_DLINK, 0x4302) }, /* D-Link DGE-530T Rev C1 */
+ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4320) }, /* Marvell Yukon 88E8001/8003/8010 */
+ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x5005) }, /* Belkin */
+ { PCI_DEVICE(PCI_VENDOR_ID_CNET, 0x434E) }, /* CNet PowerG-2000 */
+ { PCI_DEVICE(PCI_VENDOR_ID_LINKSYS, 0x1064) }, /* Linksys EG1064 v2 */
+ { PCI_VENDOR_ID_LINKSYS, 0x1032, PCI_ANY_ID, 0x0015 }, /* Linksys EG1032 v2 */
+ { 0 }
+};
+MODULE_DEVICE_TABLE(pci, skge_id_table);
+
+static int skge_up(struct net_device *dev);
+static int skge_down(struct net_device *dev);
+static void skge_phy_reset(struct skge_port *skge);
+static void skge_tx_clean(struct net_device *dev);
+static int xm_phy_write(struct skge_hw *hw, int port, u16 reg, u16 val);
+static int gm_phy_write(struct skge_hw *hw, int port, u16 reg, u16 val);
+static void genesis_get_stats(struct skge_port *skge, u64 *data);
+static void yukon_get_stats(struct skge_port *skge, u64 *data);
+static void yukon_init(struct skge_hw *hw, int port);
+static void genesis_mac_init(struct skge_hw *hw, int port);
+static void genesis_link_up(struct skge_port *skge);
+static void skge_set_multicast(struct net_device *dev);
+static irqreturn_t skge_intr(int irq, void *dev_id);
+
+/* Avoid conditionals by using array */
+static const int txqaddr[] = { Q_XA1, Q_XA2 };
+static const int rxqaddr[] = { Q_R1, Q_R2 };
+static const u32 rxirqmask[] = { IS_R1_F, IS_R2_F };
+static const u32 txirqmask[] = { IS_XA1_F, IS_XA2_F };
+static const u32 napimask[] = { IS_R1_F|IS_XA1_F, IS_R2_F|IS_XA2_F };
+static const u32 portmask[] = { IS_PORT_1, IS_PORT_2 };
+
+static inline bool is_genesis(const struct skge_hw *hw)
+{
+#ifdef CONFIG_SKGE_GENESIS
+ return hw->chip_id == CHIP_ID_GENESIS;
+#else
+ return false;
+#endif
+}
+
+static int skge_get_regs_len(struct net_device *dev)
+{
+ return 0x4000;
+}
+
+/*
+ * Returns copy of whole control register region
+ * Note: skip RAM address register because accessing it will
+ * cause bus hangs!
+ */
+static void skge_get_regs(struct net_device *dev, struct ethtool_regs *regs,
+ void *p)
+{
+ const struct skge_port *skge = netdev_priv(dev);
+ const void __iomem *io = skge->hw->regs;
+
+ regs->version = 1;
+ memset(p, 0, regs->len);
+ memcpy_fromio(p, io, B3_RAM_ADDR);
+
+ memcpy_fromio(p + B3_RI_WTO_R1, io + B3_RI_WTO_R1,
+ regs->len - B3_RI_WTO_R1);
+}
+
+/* Wake on Lan only supported on Yukon chips with rev 1 or above */
+static u32 wol_supported(const struct skge_hw *hw)
+{
+ if (is_genesis(hw))
+ return 0;
+
+ if (hw->chip_id == CHIP_ID_YUKON && hw->chip_rev == 0)
+ return 0;
+
+ return WAKE_MAGIC | WAKE_PHY;
+}
+
+static void skge_wol_init(struct skge_port *skge)
+{
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+ u16 ctrl;
+
+ skge_write16(hw, B0_CTST, CS_RST_CLR);
+ skge_write16(hw, SK_REG(port, GMAC_LINK_CTRL), GMLC_RST_CLR);
+
+ /* Turn on Vaux */
+ skge_write8(hw, B0_POWER_CTRL,
+ PC_VAUX_ENA | PC_VCC_ENA | PC_VAUX_ON | PC_VCC_OFF);
+
+ /* WA code for COMA mode -- clear PHY reset */
+ if (hw->chip_id == CHIP_ID_YUKON_LITE &&
+ hw->chip_rev >= CHIP_REV_YU_LITE_A3) {
+ u32 reg = skge_read32(hw, B2_GP_IO);
+ reg |= GP_DIR_9;
+ reg &= ~GP_IO_9;
+ skge_write32(hw, B2_GP_IO, reg);
+ }
+
+ skge_write32(hw, SK_REG(port, GPHY_CTRL),
+ GPC_DIS_SLEEP |
+ GPC_HWCFG_M_3 | GPC_HWCFG_M_2 | GPC_HWCFG_M_1 | GPC_HWCFG_M_0 |
+ GPC_ANEG_1 | GPC_RST_SET);
+
+ skge_write32(hw, SK_REG(port, GPHY_CTRL),
+ GPC_DIS_SLEEP |
+ GPC_HWCFG_M_3 | GPC_HWCFG_M_2 | GPC_HWCFG_M_1 | GPC_HWCFG_M_0 |
+ GPC_ANEG_1 | GPC_RST_CLR);
+
+ skge_write32(hw, SK_REG(port, GMAC_CTRL), GMC_RST_CLR);
+
+ /* Force to 10/100 skge_reset will re-enable on resume */
+ gm_phy_write(hw, port, PHY_MARV_AUNE_ADV,
+ (PHY_AN_100FULL | PHY_AN_100HALF |
+ PHY_AN_10FULL | PHY_AN_10HALF | PHY_AN_CSMA));
+ /* no 1000 HD/FD */
+ gm_phy_write(hw, port, PHY_MARV_1000T_CTRL, 0);
+ gm_phy_write(hw, port, PHY_MARV_CTRL,
+ PHY_CT_RESET | PHY_CT_SPS_LSB | PHY_CT_ANE |
+ PHY_CT_RE_CFG | PHY_CT_DUP_MD);
+
+
+ /* Set GMAC to no flow control and auto update for speed/duplex */
+ gma_write16(hw, port, GM_GP_CTRL,
+ GM_GPCR_FC_TX_DIS|GM_GPCR_TX_ENA|GM_GPCR_RX_ENA|
+ GM_GPCR_DUP_FULL|GM_GPCR_FC_RX_DIS|GM_GPCR_AU_FCT_DIS);
+
+ /* Set WOL address */
+ memcpy_toio(hw->regs + WOL_REGS(port, WOL_MAC_ADDR),
+ skge->netdev->dev_addr, ETH_ALEN);
+
+ /* Turn on appropriate WOL control bits */
+ skge_write16(hw, WOL_REGS(port, WOL_CTRL_STAT), WOL_CTL_CLEAR_RESULT);
+ ctrl = 0;
+ if (skge->wol & WAKE_PHY)
+ ctrl |= WOL_CTL_ENA_PME_ON_LINK_CHG|WOL_CTL_ENA_LINK_CHG_UNIT;
+ else
+ ctrl |= WOL_CTL_DIS_PME_ON_LINK_CHG|WOL_CTL_DIS_LINK_CHG_UNIT;
+
+ if (skge->wol & WAKE_MAGIC)
+ ctrl |= WOL_CTL_ENA_PME_ON_MAGIC_PKT|WOL_CTL_ENA_MAGIC_PKT_UNIT;
+ else
+ ctrl |= WOL_CTL_DIS_PME_ON_MAGIC_PKT|WOL_CTL_DIS_MAGIC_PKT_UNIT;
+
+ ctrl |= WOL_CTL_DIS_PME_ON_PATTERN|WOL_CTL_DIS_PATTERN_UNIT;
+ skge_write16(hw, WOL_REGS(port, WOL_CTRL_STAT), ctrl);
+
+ /* block receiver */
+ skge_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RST_SET);
+}
+
+static void skge_get_wol(struct net_device *dev, struct ethtool_wolinfo *wol)
+{
+ struct skge_port *skge = netdev_priv(dev);
+
+ wol->supported = wol_supported(skge->hw);
+ wol->wolopts = skge->wol;
+}
+
+static int skge_set_wol(struct net_device *dev, struct ethtool_wolinfo *wol)
+{
+ struct skge_port *skge = netdev_priv(dev);
+ struct skge_hw *hw = skge->hw;
+
+ if ((wol->wolopts & ~wol_supported(hw)) ||
+ !device_can_wakeup(&hw->pdev->dev))
+ return -EOPNOTSUPP;
+
+ skge->wol = wol->wolopts;
+
+ device_set_wakeup_enable(&hw->pdev->dev, skge->wol);
+
+ return 0;
+}
+
+/* Determine supported/advertised modes based on hardware.
+ * Note: ethtool ADVERTISED_xxx == SUPPORTED_xxx
+ */
+static u32 skge_supported_modes(const struct skge_hw *hw)
+{
+ u32 supported;
+
+ if (hw->copper) {
+ supported = (SUPPORTED_10baseT_Half |
+ SUPPORTED_10baseT_Full |
+ SUPPORTED_100baseT_Half |
+ SUPPORTED_100baseT_Full |
+ SUPPORTED_1000baseT_Half |
+ SUPPORTED_1000baseT_Full |
+ SUPPORTED_Autoneg |
+ SUPPORTED_TP);
+
+ if (is_genesis(hw))
+ supported &= ~(SUPPORTED_10baseT_Half |
+ SUPPORTED_10baseT_Full |
+ SUPPORTED_100baseT_Half |
+ SUPPORTED_100baseT_Full);
+
+ else if (hw->chip_id == CHIP_ID_YUKON)
+ supported &= ~SUPPORTED_1000baseT_Half;
+ } else
+ supported = (SUPPORTED_1000baseT_Full |
+ SUPPORTED_1000baseT_Half |
+ SUPPORTED_FIBRE |
+ SUPPORTED_Autoneg);
+
+ return supported;
+}
+
+static int skge_get_settings(struct net_device *dev,
+ struct ethtool_cmd *ecmd)
+{
+ struct skge_port *skge = netdev_priv(dev);
+ struct skge_hw *hw = skge->hw;
+
+ ecmd->transceiver = XCVR_INTERNAL;
+ ecmd->supported = skge_supported_modes(hw);
+
+ if (hw->copper) {
+ ecmd->port = PORT_TP;
+ ecmd->phy_address = hw->phy_addr;
+ } else
+ ecmd->port = PORT_FIBRE;
+
+ ecmd->advertising = skge->advertising;
+ ecmd->autoneg = skge->autoneg;
+ ethtool_cmd_speed_set(ecmd, skge->speed);
+ ecmd->duplex = skge->duplex;
+ return 0;
+}
+
+static int skge_set_settings(struct net_device *dev, struct ethtool_cmd *ecmd)
+{
+ struct skge_port *skge = netdev_priv(dev);
+ const struct skge_hw *hw = skge->hw;
+ u32 supported = skge_supported_modes(hw);
+ int err = 0;
+
+ if (ecmd->autoneg == AUTONEG_ENABLE) {
+ ecmd->advertising = supported;
+ skge->duplex = -1;
+ skge->speed = -1;
+ } else {
+ u32 setting;
+ u32 speed = ethtool_cmd_speed(ecmd);
+
+ switch (speed) {
+ case SPEED_1000:
+ if (ecmd->duplex == DUPLEX_FULL)
+ setting = SUPPORTED_1000baseT_Full;
+ else if (ecmd->duplex == DUPLEX_HALF)
+ setting = SUPPORTED_1000baseT_Half;
+ else
+ return -EINVAL;
+ break;
+ case SPEED_100:
+ if (ecmd->duplex == DUPLEX_FULL)
+ setting = SUPPORTED_100baseT_Full;
+ else if (ecmd->duplex == DUPLEX_HALF)
+ setting = SUPPORTED_100baseT_Half;
+ else
+ return -EINVAL;
+ break;
+
+ case SPEED_10:
+ if (ecmd->duplex == DUPLEX_FULL)
+ setting = SUPPORTED_10baseT_Full;
+ else if (ecmd->duplex == DUPLEX_HALF)
+ setting = SUPPORTED_10baseT_Half;
+ else
+ return -EINVAL;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ if ((setting & supported) == 0)
+ return -EINVAL;
+
+ skge->speed = speed;
+ skge->duplex = ecmd->duplex;
+ }
+
+ skge->autoneg = ecmd->autoneg;
+ skge->advertising = ecmd->advertising;
+
+ if (netif_running(dev)) {
+ skge_down(dev);
+ err = skge_up(dev);
+ if (err) {
+ dev_close(dev);
+ return err;
+ }
+ }
+
+ return 0;
+}
+
+static void skge_get_drvinfo(struct net_device *dev,
+ struct ethtool_drvinfo *info)
+{
+ struct skge_port *skge = netdev_priv(dev);
+
+ strlcpy(info->driver, DRV_NAME, sizeof(info->driver));
+ strlcpy(info->version, DRV_VERSION, sizeof(info->version));
+ strlcpy(info->bus_info, pci_name(skge->hw->pdev),
+ sizeof(info->bus_info));
+}
+
+static const struct skge_stat {
+ char name[ETH_GSTRING_LEN];
+ u16 xmac_offset;
+ u16 gma_offset;
+} skge_stats[] = {
+ { "tx_bytes", XM_TXO_OK_HI, GM_TXO_OK_HI },
+ { "rx_bytes", XM_RXO_OK_HI, GM_RXO_OK_HI },
+
+ { "tx_broadcast", XM_TXF_BC_OK, GM_TXF_BC_OK },
+ { "rx_broadcast", XM_RXF_BC_OK, GM_RXF_BC_OK },
+ { "tx_multicast", XM_TXF_MC_OK, GM_TXF_MC_OK },
+ { "rx_multicast", XM_RXF_MC_OK, GM_RXF_MC_OK },
+ { "tx_unicast", XM_TXF_UC_OK, GM_TXF_UC_OK },
+ { "rx_unicast", XM_RXF_UC_OK, GM_RXF_UC_OK },
+ { "tx_mac_pause", XM_TXF_MPAUSE, GM_TXF_MPAUSE },
+ { "rx_mac_pause", XM_RXF_MPAUSE, GM_RXF_MPAUSE },
+
+ { "collisions", XM_TXF_SNG_COL, GM_TXF_SNG_COL },
+ { "multi_collisions", XM_TXF_MUL_COL, GM_TXF_MUL_COL },
+ { "aborted", XM_TXF_ABO_COL, GM_TXF_ABO_COL },
+ { "late_collision", XM_TXF_LAT_COL, GM_TXF_LAT_COL },
+ { "fifo_underrun", XM_TXE_FIFO_UR, GM_TXE_FIFO_UR },
+ { "fifo_overflow", XM_RXE_FIFO_OV, GM_RXE_FIFO_OV },
+
+ { "rx_toolong", XM_RXF_LNG_ERR, GM_RXF_LNG_ERR },
+ { "rx_jabber", XM_RXF_JAB_PKT, GM_RXF_JAB_PKT },
+ { "rx_runt", XM_RXE_RUNT, GM_RXE_FRAG },
+ { "rx_too_long", XM_RXF_LNG_ERR, GM_RXF_LNG_ERR },
+ { "rx_fcs_error", XM_RXF_FCS_ERR, GM_RXF_FCS_ERR },
+};
+
+static int skge_get_sset_count(struct net_device *dev, int sset)
+{
+ switch (sset) {
+ case ETH_SS_STATS:
+ return ARRAY_SIZE(skge_stats);
+ default:
+ return -EOPNOTSUPP;
+ }
+}
+
+static void skge_get_ethtool_stats(struct net_device *dev,
+ struct ethtool_stats *stats, u64 *data)
+{
+ struct skge_port *skge = netdev_priv(dev);
+
+ if (is_genesis(skge->hw))
+ genesis_get_stats(skge, data);
+ else
+ yukon_get_stats(skge, data);
+}
+
+/* Use hardware MIB variables for critical path statistics and
+ * transmit feedback not reported at interrupt.
+ * Other errors are accounted for in interrupt handler.
+ */
+static struct net_device_stats *skge_get_stats(struct net_device *dev)
+{
+ struct skge_port *skge = netdev_priv(dev);
+ u64 data[ARRAY_SIZE(skge_stats)];
+
+ if (is_genesis(skge->hw))
+ genesis_get_stats(skge, data);
+ else
+ yukon_get_stats(skge, data);
+
+ dev->stats.tx_bytes = data[0];
+ dev->stats.rx_bytes = data[1];
+ dev->stats.tx_packets = data[2] + data[4] + data[6];
+ dev->stats.rx_packets = data[3] + data[5] + data[7];
+ dev->stats.multicast = data[3] + data[5];
+ dev->stats.collisions = data[10];
+ dev->stats.tx_aborted_errors = data[12];
+
+ return &dev->stats;
+}
+
+static void skge_get_strings(struct net_device *dev, u32 stringset, u8 *data)
+{
+ int i;
+
+ switch (stringset) {
+ case ETH_SS_STATS:
+ for (i = 0; i < ARRAY_SIZE(skge_stats); i++)
+ memcpy(data + i * ETH_GSTRING_LEN,
+ skge_stats[i].name, ETH_GSTRING_LEN);
+ break;
+ }
+}
+
+static void skge_get_ring_param(struct net_device *dev,
+ struct ethtool_ringparam *p)
+{
+ struct skge_port *skge = netdev_priv(dev);
+
+ p->rx_max_pending = MAX_RX_RING_SIZE;
+ p->tx_max_pending = MAX_TX_RING_SIZE;
+
+ p->rx_pending = skge->rx_ring.count;
+ p->tx_pending = skge->tx_ring.count;
+}
+
+static int skge_set_ring_param(struct net_device *dev,
+ struct ethtool_ringparam *p)
+{
+ struct skge_port *skge = netdev_priv(dev);
+ int err = 0;
+
+ if (p->rx_pending == 0 || p->rx_pending > MAX_RX_RING_SIZE ||
+ p->tx_pending < TX_LOW_WATER || p->tx_pending > MAX_TX_RING_SIZE)
+ return -EINVAL;
+
+ skge->rx_ring.count = p->rx_pending;
+ skge->tx_ring.count = p->tx_pending;
+
+ if (netif_running(dev)) {
+ skge_down(dev);
+ err = skge_up(dev);
+ if (err)
+ dev_close(dev);
+ }
+
+ return err;
+}
+
+static u32 skge_get_msglevel(struct net_device *netdev)
+{
+ struct skge_port *skge = netdev_priv(netdev);
+ return skge->msg_enable;
+}
+
+static void skge_set_msglevel(struct net_device *netdev, u32 value)
+{
+ struct skge_port *skge = netdev_priv(netdev);
+ skge->msg_enable = value;
+}
+
+static int skge_nway_reset(struct net_device *dev)
+{
+ struct skge_port *skge = netdev_priv(dev);
+
+ if (skge->autoneg != AUTONEG_ENABLE || !netif_running(dev))
+ return -EINVAL;
+
+ skge_phy_reset(skge);
+ return 0;
+}
+
+static void skge_get_pauseparam(struct net_device *dev,
+ struct ethtool_pauseparam *ecmd)
+{
+ struct skge_port *skge = netdev_priv(dev);
+
+ ecmd->rx_pause = ((skge->flow_control == FLOW_MODE_SYMMETRIC) ||
+ (skge->flow_control == FLOW_MODE_SYM_OR_REM));
+ ecmd->tx_pause = (ecmd->rx_pause ||
+ (skge->flow_control == FLOW_MODE_LOC_SEND));
+
+ ecmd->autoneg = ecmd->rx_pause || ecmd->tx_pause;
+}
+
+static int skge_set_pauseparam(struct net_device *dev,
+ struct ethtool_pauseparam *ecmd)
+{
+ struct skge_port *skge = netdev_priv(dev);
+ struct ethtool_pauseparam old;
+ int err = 0;
+
+ skge_get_pauseparam(dev, &old);
+
+ if (ecmd->autoneg != old.autoneg)
+ skge->flow_control = ecmd->autoneg ? FLOW_MODE_NONE : FLOW_MODE_SYMMETRIC;
+ else {
+ if (ecmd->rx_pause && ecmd->tx_pause)
+ skge->flow_control = FLOW_MODE_SYMMETRIC;
+ else if (ecmd->rx_pause && !ecmd->tx_pause)
+ skge->flow_control = FLOW_MODE_SYM_OR_REM;
+ else if (!ecmd->rx_pause && ecmd->tx_pause)
+ skge->flow_control = FLOW_MODE_LOC_SEND;
+ else
+ skge->flow_control = FLOW_MODE_NONE;
+ }
+
+ if (netif_running(dev)) {
+ skge_down(dev);
+ err = skge_up(dev);
+ if (err) {
+ dev_close(dev);
+ return err;
+ }
+ }
+
+ return 0;
+}
+
+/* Chip internal frequency for clock calculations */
+static inline u32 hwkhz(const struct skge_hw *hw)
+{
+ return is_genesis(hw) ? 53125 : 78125;
+}
+
+/* Chip HZ to microseconds */
+static inline u32 skge_clk2usec(const struct skge_hw *hw, u32 ticks)
+{
+ return (ticks * 1000) / hwkhz(hw);
+}
+
+/* Microseconds to chip HZ */
+static inline u32 skge_usecs2clk(const struct skge_hw *hw, u32 usec)
+{
+ return hwkhz(hw) * usec / 1000;
+}
+
+static int skge_get_coalesce(struct net_device *dev,
+ struct ethtool_coalesce *ecmd)
+{
+ struct skge_port *skge = netdev_priv(dev);
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+
+ ecmd->rx_coalesce_usecs = 0;
+ ecmd->tx_coalesce_usecs = 0;
+
+ if (skge_read32(hw, B2_IRQM_CTRL) & TIM_START) {
+ u32 delay = skge_clk2usec(hw, skge_read32(hw, B2_IRQM_INI));
+ u32 msk = skge_read32(hw, B2_IRQM_MSK);
+
+ if (msk & rxirqmask[port])
+ ecmd->rx_coalesce_usecs = delay;
+ if (msk & txirqmask[port])
+ ecmd->tx_coalesce_usecs = delay;
+ }
+
+ return 0;
+}
+
+/* Note: interrupt timer is per board, but can turn on/off per port */
+static int skge_set_coalesce(struct net_device *dev,
+ struct ethtool_coalesce *ecmd)
+{
+ struct skge_port *skge = netdev_priv(dev);
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+ u32 msk = skge_read32(hw, B2_IRQM_MSK);
+ u32 delay = 25;
+
+ if (ecmd->rx_coalesce_usecs == 0)
+ msk &= ~rxirqmask[port];
+ else if (ecmd->rx_coalesce_usecs < 25 ||
+ ecmd->rx_coalesce_usecs > 33333)
+ return -EINVAL;
+ else {
+ msk |= rxirqmask[port];
+ delay = ecmd->rx_coalesce_usecs;
+ }
+
+ if (ecmd->tx_coalesce_usecs == 0)
+ msk &= ~txirqmask[port];
+ else if (ecmd->tx_coalesce_usecs < 25 ||
+ ecmd->tx_coalesce_usecs > 33333)
+ return -EINVAL;
+ else {
+ msk |= txirqmask[port];
+ delay = min(delay, ecmd->rx_coalesce_usecs);
+ }
+
+ skge_write32(hw, B2_IRQM_MSK, msk);
+ if (msk == 0)
+ skge_write32(hw, B2_IRQM_CTRL, TIM_STOP);
+ else {
+ skge_write32(hw, B2_IRQM_INI, skge_usecs2clk(hw, delay));
+ skge_write32(hw, B2_IRQM_CTRL, TIM_START);
+ }
+ return 0;
+}
+
+enum led_mode { LED_MODE_OFF, LED_MODE_ON, LED_MODE_TST };
+static void skge_led(struct skge_port *skge, enum led_mode mode)
+{
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+
+ spin_lock_bh(&hw->phy_lock);
+ if (is_genesis(hw)) {
+ switch (mode) {
+ case LED_MODE_OFF:
+ if (hw->phy_type == SK_PHY_BCOM)
+ xm_phy_write(hw, port, PHY_BCOM_P_EXT_CTRL, PHY_B_PEC_LED_OFF);
+ else {
+ skge_write32(hw, SK_REG(port, TX_LED_VAL), 0);
+ skge_write8(hw, SK_REG(port, TX_LED_CTRL), LED_T_OFF);
+ }
+ skge_write8(hw, SK_REG(port, LNK_LED_REG), LINKLED_OFF);
+ skge_write32(hw, SK_REG(port, RX_LED_VAL), 0);
+ skge_write8(hw, SK_REG(port, RX_LED_CTRL), LED_T_OFF);
+ break;
+
+ case LED_MODE_ON:
+ skge_write8(hw, SK_REG(port, LNK_LED_REG), LINKLED_ON);
+ skge_write8(hw, SK_REG(port, LNK_LED_REG), LINKLED_LINKSYNC_ON);
+
+ skge_write8(hw, SK_REG(port, RX_LED_CTRL), LED_START);
+ skge_write8(hw, SK_REG(port, TX_LED_CTRL), LED_START);
+
+ break;
+
+ case LED_MODE_TST:
+ skge_write8(hw, SK_REG(port, RX_LED_TST), LED_T_ON);
+ skge_write32(hw, SK_REG(port, RX_LED_VAL), 100);
+ skge_write8(hw, SK_REG(port, RX_LED_CTRL), LED_START);
+
+ if (hw->phy_type == SK_PHY_BCOM)
+ xm_phy_write(hw, port, PHY_BCOM_P_EXT_CTRL, PHY_B_PEC_LED_ON);
+ else {
+ skge_write8(hw, SK_REG(port, TX_LED_TST), LED_T_ON);
+ skge_write32(hw, SK_REG(port, TX_LED_VAL), 100);
+ skge_write8(hw, SK_REG(port, TX_LED_CTRL), LED_START);
+ }
+
+ }
+ } else {
+ switch (mode) {
+ case LED_MODE_OFF:
+ gm_phy_write(hw, port, PHY_MARV_LED_CTRL, 0);
+ gm_phy_write(hw, port, PHY_MARV_LED_OVER,
+ PHY_M_LED_MO_DUP(MO_LED_OFF) |
+ PHY_M_LED_MO_10(MO_LED_OFF) |
+ PHY_M_LED_MO_100(MO_LED_OFF) |
+ PHY_M_LED_MO_1000(MO_LED_OFF) |
+ PHY_M_LED_MO_RX(MO_LED_OFF));
+ break;
+ case LED_MODE_ON:
+ gm_phy_write(hw, port, PHY_MARV_LED_CTRL,
+ PHY_M_LED_PULS_DUR(PULS_170MS) |
+ PHY_M_LED_BLINK_RT(BLINK_84MS) |
+ PHY_M_LEDC_TX_CTRL |
+ PHY_M_LEDC_DP_CTRL);
+
+ gm_phy_write(hw, port, PHY_MARV_LED_OVER,
+ PHY_M_LED_MO_RX(MO_LED_OFF) |
+ (skge->speed == SPEED_100 ?
+ PHY_M_LED_MO_100(MO_LED_ON) : 0));
+ break;
+ case LED_MODE_TST:
+ gm_phy_write(hw, port, PHY_MARV_LED_CTRL, 0);
+ gm_phy_write(hw, port, PHY_MARV_LED_OVER,
+ PHY_M_LED_MO_DUP(MO_LED_ON) |
+ PHY_M_LED_MO_10(MO_LED_ON) |
+ PHY_M_LED_MO_100(MO_LED_ON) |
+ PHY_M_LED_MO_1000(MO_LED_ON) |
+ PHY_M_LED_MO_RX(MO_LED_ON));
+ }
+ }
+ spin_unlock_bh(&hw->phy_lock);
+}
+
+/* blink LED's for finding board */
+static int skge_set_phys_id(struct net_device *dev,
+ enum ethtool_phys_id_state state)
+{
+ struct skge_port *skge = netdev_priv(dev);
+
+ switch (state) {
+ case ETHTOOL_ID_ACTIVE:
+ return 2; /* cycle on/off twice per second */
+
+ case ETHTOOL_ID_ON:
+ skge_led(skge, LED_MODE_TST);
+ break;
+
+ case ETHTOOL_ID_OFF:
+ skge_led(skge, LED_MODE_OFF);
+ break;
+
+ case ETHTOOL_ID_INACTIVE:
+ /* back to regular LED state */
+ skge_led(skge, netif_running(dev) ? LED_MODE_ON : LED_MODE_OFF);
+ }
+
+ return 0;
+}
+
+static int skge_get_eeprom_len(struct net_device *dev)
+{
+ struct skge_port *skge = netdev_priv(dev);
+ u32 reg2;
+
+ pci_read_config_dword(skge->hw->pdev, PCI_DEV_REG2, ®2);
+ return 1 << (((reg2 & PCI_VPD_ROM_SZ) >> 14) + 8);
+}
+
+static u32 skge_vpd_read(struct pci_dev *pdev, int cap, u16 offset)
+{
+ u32 val;
+
+ pci_write_config_word(pdev, cap + PCI_VPD_ADDR, offset);
+
+ do {
+ pci_read_config_word(pdev, cap + PCI_VPD_ADDR, &offset);
+ } while (!(offset & PCI_VPD_ADDR_F));
+
+ pci_read_config_dword(pdev, cap + PCI_VPD_DATA, &val);
+ return val;
+}
+
+static void skge_vpd_write(struct pci_dev *pdev, int cap, u16 offset, u32 val)
+{
+ pci_write_config_dword(pdev, cap + PCI_VPD_DATA, val);
+ pci_write_config_word(pdev, cap + PCI_VPD_ADDR,
+ offset | PCI_VPD_ADDR_F);
+
+ do {
+ pci_read_config_word(pdev, cap + PCI_VPD_ADDR, &offset);
+ } while (offset & PCI_VPD_ADDR_F);
+}
+
+static int skge_get_eeprom(struct net_device *dev, struct ethtool_eeprom *eeprom,
+ u8 *data)
+{
+ struct skge_port *skge = netdev_priv(dev);
+ struct pci_dev *pdev = skge->hw->pdev;
+ int cap = pci_find_capability(pdev, PCI_CAP_ID_VPD);
+ int length = eeprom->len;
+ u16 offset = eeprom->offset;
+
+ if (!cap)
+ return -EINVAL;
+
+ eeprom->magic = SKGE_EEPROM_MAGIC;
+
+ while (length > 0) {
+ u32 val = skge_vpd_read(pdev, cap, offset);
+ int n = min_t(int, length, sizeof(val));
+
+ memcpy(data, &val, n);
+ length -= n;
+ data += n;
+ offset += n;
+ }
+ return 0;
+}
+
+static int skge_set_eeprom(struct net_device *dev, struct ethtool_eeprom *eeprom,
+ u8 *data)
+{
+ struct skge_port *skge = netdev_priv(dev);
+ struct pci_dev *pdev = skge->hw->pdev;
+ int cap = pci_find_capability(pdev, PCI_CAP_ID_VPD);
+ int length = eeprom->len;
+ u16 offset = eeprom->offset;
+
+ if (!cap)
+ return -EINVAL;
+
+ if (eeprom->magic != SKGE_EEPROM_MAGIC)
+ return -EINVAL;
+
+ while (length > 0) {
+ u32 val;
+ int n = min_t(int, length, sizeof(val));
+
+ if (n < sizeof(val))
+ val = skge_vpd_read(pdev, cap, offset);
+ memcpy(&val, data, n);
+
+ skge_vpd_write(pdev, cap, offset, val);
+
+ length -= n;
+ data += n;
+ offset += n;
+ }
+ return 0;
+}
+
+static const struct ethtool_ops skge_ethtool_ops = {
+ .get_settings = skge_get_settings,
+ .set_settings = skge_set_settings,
+ .get_drvinfo = skge_get_drvinfo,
+ .get_regs_len = skge_get_regs_len,
+ .get_regs = skge_get_regs,
+ .get_wol = skge_get_wol,
+ .set_wol = skge_set_wol,
+ .get_msglevel = skge_get_msglevel,
+ .set_msglevel = skge_set_msglevel,
+ .nway_reset = skge_nway_reset,
+ .get_link = ethtool_op_get_link,
+ .get_eeprom_len = skge_get_eeprom_len,
+ .get_eeprom = skge_get_eeprom,
+ .set_eeprom = skge_set_eeprom,
+ .get_ringparam = skge_get_ring_param,
+ .set_ringparam = skge_set_ring_param,
+ .get_pauseparam = skge_get_pauseparam,
+ .set_pauseparam = skge_set_pauseparam,
+ .get_coalesce = skge_get_coalesce,
+ .set_coalesce = skge_set_coalesce,
+ .get_strings = skge_get_strings,
+ .set_phys_id = skge_set_phys_id,
+ .get_sset_count = skge_get_sset_count,
+ .get_ethtool_stats = skge_get_ethtool_stats,
+};
+
+/*
+ * Allocate ring elements and chain them together
+ * One-to-one association of board descriptors with ring elements
+ */
+static int skge_ring_alloc(struct skge_ring *ring, void *vaddr, u32 base)
+{
+ struct skge_tx_desc *d;
+ struct skge_element *e;
+ int i;
+
+ ring->start = kcalloc(ring->count, sizeof(*e), GFP_KERNEL);
+ if (!ring->start)
+ return -ENOMEM;
+
+ for (i = 0, e = ring->start, d = vaddr; i < ring->count; i++, e++, d++) {
+ e->desc = d;
+ if (i == ring->count - 1) {
+ e->next = ring->start;
+ d->next_offset = base;
+ } else {
+ e->next = e + 1;
+ d->next_offset = base + (i+1) * sizeof(*d);
+ }
+ }
+ ring->to_use = ring->to_clean = ring->start;
+
+ return 0;
+}
+
+/* Allocate and setup a new buffer for receiving */
+static int skge_rx_setup(struct skge_port *skge, struct skge_element *e,
+ struct sk_buff *skb, unsigned int bufsize)
+{
+ struct skge_rx_desc *rd = e->desc;
+ dma_addr_t map;
+
+ map = pci_map_single(skge->hw->pdev, skb->data, bufsize,
+ PCI_DMA_FROMDEVICE);
+
+ if (pci_dma_mapping_error(skge->hw->pdev, map))
+ return -1;
+
+ rd->dma_lo = lower_32_bits(map);
+ rd->dma_hi = upper_32_bits(map);
+ e->skb = skb;
+ rd->csum1_start = ETH_HLEN;
+ rd->csum2_start = ETH_HLEN;
+ rd->csum1 = 0;
+ rd->csum2 = 0;
+
+ wmb();
+
+ rd->control = BMU_OWN | BMU_STF | BMU_IRQ_EOF | BMU_TCP_CHECK | bufsize;
+ dma_unmap_addr_set(e, mapaddr, map);
+ dma_unmap_len_set(e, maplen, bufsize);
+ return 0;
+}
+
+/* Resume receiving using existing skb,
+ * Note: DMA address is not changed by chip.
+ * MTU not changed while receiver active.
+ */
+static inline void skge_rx_reuse(struct skge_element *e, unsigned int size)
+{
+ struct skge_rx_desc *rd = e->desc;
+
+ rd->csum2 = 0;
+ rd->csum2_start = ETH_HLEN;
+
+ wmb();
+
+ rd->control = BMU_OWN | BMU_STF | BMU_IRQ_EOF | BMU_TCP_CHECK | size;
+}
+
+
+/* Free all buffers in receive ring, assumes receiver stopped */
+static void skge_rx_clean(struct skge_port *skge)
+{
+ struct skge_hw *hw = skge->hw;
+ struct skge_ring *ring = &skge->rx_ring;
+ struct skge_element *e;
+
+ e = ring->start;
+ do {
+ struct skge_rx_desc *rd = e->desc;
+ rd->control = 0;
+ if (e->skb) {
+ pci_unmap_single(hw->pdev,
+ dma_unmap_addr(e, mapaddr),
+ dma_unmap_len(e, maplen),
+ PCI_DMA_FROMDEVICE);
+ dev_kfree_skb(e->skb);
+ e->skb = NULL;
+ }
+ } while ((e = e->next) != ring->start);
+}
+
+
+/* Allocate buffers for receive ring
+ * For receive: to_clean is next received frame.
+ */
+static int skge_rx_fill(struct net_device *dev)
+{
+ struct skge_port *skge = netdev_priv(dev);
+ struct skge_ring *ring = &skge->rx_ring;
+ struct skge_element *e;
+
+ e = ring->start;
+ do {
+ struct sk_buff *skb;
+
+ skb = __netdev_alloc_skb(dev, skge->rx_buf_size + NET_IP_ALIGN,
+ GFP_KERNEL);
+ if (!skb)
+ return -ENOMEM;
+
+ skb_reserve(skb, NET_IP_ALIGN);
+ if (skge_rx_setup(skge, e, skb, skge->rx_buf_size) < 0) {
+ dev_kfree_skb(skb);
+ return -EIO;
+ }
+ } while ((e = e->next) != ring->start);
+
+ ring->to_clean = ring->start;
+ return 0;
+}
+
+static const char *skge_pause(enum pause_status status)
+{
+ switch (status) {
+ case FLOW_STAT_NONE:
+ return "none";
+ case FLOW_STAT_REM_SEND:
+ return "rx only";
+ case FLOW_STAT_LOC_SEND:
+ return "tx_only";
+ case FLOW_STAT_SYMMETRIC: /* Both station may send PAUSE */
+ return "both";
+ default:
+ return "indeterminated";
+ }
+}
+
+
+static void skge_link_up(struct skge_port *skge)
+{
+ skge_write8(skge->hw, SK_REG(skge->port, LNK_LED_REG),
+ LED_BLK_OFF|LED_SYNC_OFF|LED_ON);
+
+ netif_carrier_on(skge->netdev);
+ netif_wake_queue(skge->netdev);
+
+ netif_info(skge, link, skge->netdev,
+ "Link is up at %d Mbps, %s duplex, flow control %s\n",
+ skge->speed,
+ skge->duplex == DUPLEX_FULL ? "full" : "half",
+ skge_pause(skge->flow_status));
+}
+
+static void skge_link_down(struct skge_port *skge)
+{
+ skge_write8(skge->hw, SK_REG(skge->port, LNK_LED_REG), LED_OFF);
+ netif_carrier_off(skge->netdev);
+ netif_stop_queue(skge->netdev);
+
+ netif_info(skge, link, skge->netdev, "Link is down\n");
+}
+
+static void xm_link_down(struct skge_hw *hw, int port)
+{
+ struct net_device *dev = hw->dev[port];
+ struct skge_port *skge = netdev_priv(dev);
+
+ xm_write16(hw, port, XM_IMSK, XM_IMSK_DISABLE);
+
+ if (netif_carrier_ok(dev))
+ skge_link_down(skge);
+}
+
+static int __xm_phy_read(struct skge_hw *hw, int port, u16 reg, u16 *val)
+{
+ int i;
+
+ xm_write16(hw, port, XM_PHY_ADDR, reg | hw->phy_addr);
+ *val = xm_read16(hw, port, XM_PHY_DATA);
+
+ if (hw->phy_type == SK_PHY_XMAC)
+ goto ready;
+
+ for (i = 0; i < PHY_RETRIES; i++) {
+ if (xm_read16(hw, port, XM_MMU_CMD) & XM_MMU_PHY_RDY)
+ goto ready;
+ udelay(1);
+ }
+
+ return -ETIMEDOUT;
+ ready:
+ *val = xm_read16(hw, port, XM_PHY_DATA);
+
+ return 0;
+}
+
+static u16 xm_phy_read(struct skge_hw *hw, int port, u16 reg)
+{
+ u16 v = 0;
+ if (__xm_phy_read(hw, port, reg, &v))
+ pr_warn("%s: phy read timed out\n", hw->dev[port]->name);
+ return v;
+}
+
+static int xm_phy_write(struct skge_hw *hw, int port, u16 reg, u16 val)
+{
+ int i;
+
+ xm_write16(hw, port, XM_PHY_ADDR, reg | hw->phy_addr);
+ for (i = 0; i < PHY_RETRIES; i++) {
+ if (!(xm_read16(hw, port, XM_MMU_CMD) & XM_MMU_PHY_BUSY))
+ goto ready;
+ udelay(1);
+ }
+ return -EIO;
+
+ ready:
+ xm_write16(hw, port, XM_PHY_DATA, val);
+ for (i = 0; i < PHY_RETRIES; i++) {
+ if (!(xm_read16(hw, port, XM_MMU_CMD) & XM_MMU_PHY_BUSY))
+ return 0;
+ udelay(1);
+ }
+ return -ETIMEDOUT;
+}
+
+static void genesis_init(struct skge_hw *hw)
+{
+ /* set blink source counter */
+ skge_write32(hw, B2_BSC_INI, (SK_BLK_DUR * SK_FACT_53) / 100);
+ skge_write8(hw, B2_BSC_CTRL, BSC_START);
+
+ /* configure mac arbiter */
+ skge_write16(hw, B3_MA_TO_CTRL, MA_RST_CLR);
+
+ /* configure mac arbiter timeout values */
+ skge_write8(hw, B3_MA_TOINI_RX1, SK_MAC_TO_53);
+ skge_write8(hw, B3_MA_TOINI_RX2, SK_MAC_TO_53);
+ skge_write8(hw, B3_MA_TOINI_TX1, SK_MAC_TO_53);
+ skge_write8(hw, B3_MA_TOINI_TX2, SK_MAC_TO_53);
+
+ skge_write8(hw, B3_MA_RCINI_RX1, 0);
+ skge_write8(hw, B3_MA_RCINI_RX2, 0);
+ skge_write8(hw, B3_MA_RCINI_TX1, 0);
+ skge_write8(hw, B3_MA_RCINI_TX2, 0);
+
+ /* configure packet arbiter timeout */
+ skge_write16(hw, B3_PA_CTRL, PA_RST_CLR);
+ skge_write16(hw, B3_PA_TOINI_RX1, SK_PKT_TO_MAX);
+ skge_write16(hw, B3_PA_TOINI_TX1, SK_PKT_TO_MAX);
+ skge_write16(hw, B3_PA_TOINI_RX2, SK_PKT_TO_MAX);
+ skge_write16(hw, B3_PA_TOINI_TX2, SK_PKT_TO_MAX);
+}
+
+static void genesis_reset(struct skge_hw *hw, int port)
+{
+ static const u8 zero[8] = { 0 };
+ u32 reg;
+
+ skge_write8(hw, SK_REG(port, GMAC_IRQ_MSK), 0);
+
+ /* reset the statistics module */
+ xm_write32(hw, port, XM_GP_PORT, XM_GP_RES_STAT);
+ xm_write16(hw, port, XM_IMSK, XM_IMSK_DISABLE);
+ xm_write32(hw, port, XM_MODE, 0); /* clear Mode Reg */
+ xm_write16(hw, port, XM_TX_CMD, 0); /* reset TX CMD Reg */
+ xm_write16(hw, port, XM_RX_CMD, 0); /* reset RX CMD Reg */
+
+ /* disable Broadcom PHY IRQ */
+ if (hw->phy_type == SK_PHY_BCOM)
+ xm_write16(hw, port, PHY_BCOM_INT_MASK, 0xffff);
+
+ xm_outhash(hw, port, XM_HSM, zero);
+
+ /* Flush TX and RX fifo */
+ reg = xm_read32(hw, port, XM_MODE);
+ xm_write32(hw, port, XM_MODE, reg | XM_MD_FTF);
+ xm_write32(hw, port, XM_MODE, reg | XM_MD_FRF);
+}
+
+/* Convert mode to MII values */
+static const u16 phy_pause_map[] = {
+ [FLOW_MODE_NONE] = 0,
+ [FLOW_MODE_LOC_SEND] = PHY_AN_PAUSE_ASYM,
+ [FLOW_MODE_SYMMETRIC] = PHY_AN_PAUSE_CAP,
+ [FLOW_MODE_SYM_OR_REM] = PHY_AN_PAUSE_CAP | PHY_AN_PAUSE_ASYM,
+};
+
+/* special defines for FIBER (88E1011S only) */
+static const u16 fiber_pause_map[] = {
+ [FLOW_MODE_NONE] = PHY_X_P_NO_PAUSE,
+ [FLOW_MODE_LOC_SEND] = PHY_X_P_ASYM_MD,
+ [FLOW_MODE_SYMMETRIC] = PHY_X_P_SYM_MD,
+ [FLOW_MODE_SYM_OR_REM] = PHY_X_P_BOTH_MD,
+};
+
+
+/* Check status of Broadcom phy link */
+static void bcom_check_link(struct skge_hw *hw, int port)
+{
+ struct net_device *dev = hw->dev[port];
+ struct skge_port *skge = netdev_priv(dev);
+ u16 status;
+
+ /* read twice because of latch */
+ xm_phy_read(hw, port, PHY_BCOM_STAT);
+ status = xm_phy_read(hw, port, PHY_BCOM_STAT);
+
+ if ((status & PHY_ST_LSYNC) == 0) {
+ xm_link_down(hw, port);
+ return;
+ }
+
+ if (skge->autoneg == AUTONEG_ENABLE) {
+ u16 lpa, aux;
+
+ if (!(status & PHY_ST_AN_OVER))
+ return;
+
+ lpa = xm_phy_read(hw, port, PHY_XMAC_AUNE_LP);
+ if (lpa & PHY_B_AN_RF) {
+ netdev_notice(dev, "remote fault\n");
+ return;
+ }
+
+ aux = xm_phy_read(hw, port, PHY_BCOM_AUX_STAT);
+
+ /* Check Duplex mismatch */
+ switch (aux & PHY_B_AS_AN_RES_MSK) {
+ case PHY_B_RES_1000FD:
+ skge->duplex = DUPLEX_FULL;
+ break;
+ case PHY_B_RES_1000HD:
+ skge->duplex = DUPLEX_HALF;
+ break;
+ default:
+ netdev_notice(dev, "duplex mismatch\n");
+ return;
+ }
+
+ /* We are using IEEE 802.3z/D5.0 Table 37-4 */
+ switch (aux & PHY_B_AS_PAUSE_MSK) {
+ case PHY_B_AS_PAUSE_MSK:
+ skge->flow_status = FLOW_STAT_SYMMETRIC;
+ break;
+ case PHY_B_AS_PRR:
+ skge->flow_status = FLOW_STAT_REM_SEND;
+ break;
+ case PHY_B_AS_PRT:
+ skge->flow_status = FLOW_STAT_LOC_SEND;
+ break;
+ default:
+ skge->flow_status = FLOW_STAT_NONE;
+ }
+ skge->speed = SPEED_1000;
+ }
+
+ if (!netif_carrier_ok(dev))
+ genesis_link_up(skge);
+}
+
+/* Broadcom 5400 only supports giagabit! SysKonnect did not put an additional
+ * Phy on for 100 or 10Mbit operation
+ */
+static void bcom_phy_init(struct skge_port *skge)
+{
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+ int i;
+ u16 id1, r, ext, ctl;
+
+ /* magic workaround patterns for Broadcom */
+ static const struct {
+ u16 reg;
+ u16 val;
+ } A1hack[] = {
+ { 0x18, 0x0c20 }, { 0x17, 0x0012 }, { 0x15, 0x1104 },
+ { 0x17, 0x0013 }, { 0x15, 0x0404 }, { 0x17, 0x8006 },
+ { 0x15, 0x0132 }, { 0x17, 0x8006 }, { 0x15, 0x0232 },
+ { 0x17, 0x800D }, { 0x15, 0x000F }, { 0x18, 0x0420 },
+ }, C0hack[] = {
+ { 0x18, 0x0c20 }, { 0x17, 0x0012 }, { 0x15, 0x1204 },
+ { 0x17, 0x0013 }, { 0x15, 0x0A04 }, { 0x18, 0x0420 },
+ };
+
+ /* read Id from external PHY (all have the same address) */
+ id1 = xm_phy_read(hw, port, PHY_XMAC_ID1);
+
+ /* Optimize MDIO transfer by suppressing preamble. */
+ r = xm_read16(hw, port, XM_MMU_CMD);
+ r |= XM_MMU_NO_PRE;
+ xm_write16(hw, port, XM_MMU_CMD, r);
+
+ switch (id1) {
+ case PHY_BCOM_ID1_C0:
+ /*
+ * Workaround BCOM Errata for the C0 type.
+ * Write magic patterns to reserved registers.
+ */
+ for (i = 0; i < ARRAY_SIZE(C0hack); i++)
+ xm_phy_write(hw, port,
+ C0hack[i].reg, C0hack[i].val);
+
+ break;
+ case PHY_BCOM_ID1_A1:
+ /*
+ * Workaround BCOM Errata for the A1 type.
+ * Write magic patterns to reserved registers.
+ */
+ for (i = 0; i < ARRAY_SIZE(A1hack); i++)
+ xm_phy_write(hw, port,
+ A1hack[i].reg, A1hack[i].val);
+ break;
+ }
+
+ /*
+ * Workaround BCOM Errata (#10523) for all BCom PHYs.
+ * Disable Power Management after reset.
+ */
+ r = xm_phy_read(hw, port, PHY_BCOM_AUX_CTRL);
+ r |= PHY_B_AC_DIS_PM;
+ xm_phy_write(hw, port, PHY_BCOM_AUX_CTRL, r);
+
+ /* Dummy read */
+ xm_read16(hw, port, XM_ISRC);
+
+ ext = PHY_B_PEC_EN_LTR; /* enable tx led */
+ ctl = PHY_CT_SP1000; /* always 1000mbit */
+
+ if (skge->autoneg == AUTONEG_ENABLE) {
+ /*
+ * Workaround BCOM Errata #1 for the C5 type.
+ * 1000Base-T Link Acquisition Failure in Slave Mode
+ * Set Repeater/DTE bit 10 of the 1000Base-T Control Register
+ */
+ u16 adv = PHY_B_1000C_RD;
+ if (skge->advertising & ADVERTISED_1000baseT_Half)
+ adv |= PHY_B_1000C_AHD;
+ if (skge->advertising & ADVERTISED_1000baseT_Full)
+ adv |= PHY_B_1000C_AFD;
+ xm_phy_write(hw, port, PHY_BCOM_1000T_CTRL, adv);
+
+ ctl |= PHY_CT_ANE | PHY_CT_RE_CFG;
+ } else {
+ if (skge->duplex == DUPLEX_FULL)
+ ctl |= PHY_CT_DUP_MD;
+ /* Force to slave */
+ xm_phy_write(hw, port, PHY_BCOM_1000T_CTRL, PHY_B_1000C_MSE);
+ }
+
+ /* Set autonegotiation pause parameters */
+ xm_phy_write(hw, port, PHY_BCOM_AUNE_ADV,
+ phy_pause_map[skge->flow_control] | PHY_AN_CSMA);
+
+ /* Handle Jumbo frames */
+ if (hw->dev[port]->mtu > ETH_DATA_LEN) {
+ xm_phy_write(hw, port, PHY_BCOM_AUX_CTRL,
+ PHY_B_AC_TX_TST | PHY_B_AC_LONG_PACK);
+
+ ext |= PHY_B_PEC_HIGH_LA;
+
+ }
+
+ xm_phy_write(hw, port, PHY_BCOM_P_EXT_CTRL, ext);
+ xm_phy_write(hw, port, PHY_BCOM_CTRL, ctl);
+
+ /* Use link status change interrupt */
+ xm_phy_write(hw, port, PHY_BCOM_INT_MASK, PHY_B_DEF_MSK);
+}
+
+static void xm_phy_init(struct skge_port *skge)
+{
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+ u16 ctrl = 0;
+
+ if (skge->autoneg == AUTONEG_ENABLE) {
+ if (skge->advertising & ADVERTISED_1000baseT_Half)
+ ctrl |= PHY_X_AN_HD;
+ if (skge->advertising & ADVERTISED_1000baseT_Full)
+ ctrl |= PHY_X_AN_FD;
+
+ ctrl |= fiber_pause_map[skge->flow_control];
+
+ xm_phy_write(hw, port, PHY_XMAC_AUNE_ADV, ctrl);
+
+ /* Restart Auto-negotiation */
+ ctrl = PHY_CT_ANE | PHY_CT_RE_CFG;
+ } else {
+ /* Set DuplexMode in Config register */
+ if (skge->duplex == DUPLEX_FULL)
+ ctrl |= PHY_CT_DUP_MD;
+ /*
+ * Do NOT enable Auto-negotiation here. This would hold
+ * the link down because no IDLEs are transmitted
+ */
+ }
+
+ xm_phy_write(hw, port, PHY_XMAC_CTRL, ctrl);
+
+ /* Poll PHY for status changes */
+ mod_timer(&skge->link_timer, jiffies + LINK_HZ);
+}
+
+static int xm_check_link(struct net_device *dev)
+{
+ struct skge_port *skge = netdev_priv(dev);
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+ u16 status;
+
+ /* read twice because of latch */
+ xm_phy_read(hw, port, PHY_XMAC_STAT);
+ status = xm_phy_read(hw, port, PHY_XMAC_STAT);
+
+ if ((status & PHY_ST_LSYNC) == 0) {
+ xm_link_down(hw, port);
+ return 0;
+ }
+
+ if (skge->autoneg == AUTONEG_ENABLE) {
+ u16 lpa, res;
+
+ if (!(status & PHY_ST_AN_OVER))
+ return 0;
+
+ lpa = xm_phy_read(hw, port, PHY_XMAC_AUNE_LP);
+ if (lpa & PHY_B_AN_RF) {
+ netdev_notice(dev, "remote fault\n");
+ return 0;
+ }
+
+ res = xm_phy_read(hw, port, PHY_XMAC_RES_ABI);
+
+ /* Check Duplex mismatch */
+ switch (res & (PHY_X_RS_HD | PHY_X_RS_FD)) {
+ case PHY_X_RS_FD:
+ skge->duplex = DUPLEX_FULL;
+ break;
+ case PHY_X_RS_HD:
+ skge->duplex = DUPLEX_HALF;
+ break;
+ default:
+ netdev_notice(dev, "duplex mismatch\n");
+ return 0;
+ }
+
+ /* We are using IEEE 802.3z/D5.0 Table 37-4 */
+ if ((skge->flow_control == FLOW_MODE_SYMMETRIC ||
+ skge->flow_control == FLOW_MODE_SYM_OR_REM) &&
+ (lpa & PHY_X_P_SYM_MD))
+ skge->flow_status = FLOW_STAT_SYMMETRIC;
+ else if (skge->flow_control == FLOW_MODE_SYM_OR_REM &&
+ (lpa & PHY_X_RS_PAUSE) == PHY_X_P_ASYM_MD)
+ /* Enable PAUSE receive, disable PAUSE transmit */
+ skge->flow_status = FLOW_STAT_REM_SEND;
+ else if (skge->flow_control == FLOW_MODE_LOC_SEND &&
+ (lpa & PHY_X_RS_PAUSE) == PHY_X_P_BOTH_MD)
+ /* Disable PAUSE receive, enable PAUSE transmit */
+ skge->flow_status = FLOW_STAT_LOC_SEND;
+ else
+ skge->flow_status = FLOW_STAT_NONE;
+
+ skge->speed = SPEED_1000;
+ }
+
+ if (!netif_carrier_ok(dev))
+ genesis_link_up(skge);
+ return 1;
+}
+
+/* Poll to check for link coming up.
+ *
+ * Since internal PHY is wired to a level triggered pin, can't
+ * get an interrupt when carrier is detected, need to poll for
+ * link coming up.
+ */
+static void xm_link_timer(unsigned long arg)
+{
+ struct skge_port *skge = (struct skge_port *) arg;
+ struct net_device *dev = skge->netdev;
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+ int i;
+ unsigned long flags;
+
+ if (!netif_running(dev))
+ return;
+
+ spin_lock_irqsave(&hw->phy_lock, flags);
+
+ /*
+ * Verify that the link by checking GPIO register three times.
+ * This pin has the signal from the link_sync pin connected to it.
+ */
+ for (i = 0; i < 3; i++) {
+ if (xm_read16(hw, port, XM_GP_PORT) & XM_GP_INP_ASS)
+ goto link_down;
+ }
+
+ /* Re-enable interrupt to detect link down */
+ if (xm_check_link(dev)) {
+ u16 msk = xm_read16(hw, port, XM_IMSK);
+ msk &= ~XM_IS_INP_ASS;
+ xm_write16(hw, port, XM_IMSK, msk);
+ xm_read16(hw, port, XM_ISRC);
+ } else {
+link_down:
+ mod_timer(&skge->link_timer,
+ round_jiffies(jiffies + LINK_HZ));
+ }
+ spin_unlock_irqrestore(&hw->phy_lock, flags);
+}
+
+static void genesis_mac_init(struct skge_hw *hw, int port)
+{
+ struct net_device *dev = hw->dev[port];
+ struct skge_port *skge = netdev_priv(dev);
+ int jumbo = hw->dev[port]->mtu > ETH_DATA_LEN;
+ int i;
+ u32 r;
+ static const u8 zero[6] = { 0 };
+
+ for (i = 0; i < 10; i++) {
+ skge_write16(hw, SK_REG(port, TX_MFF_CTRL1),
+ MFF_SET_MAC_RST);
+ if (skge_read16(hw, SK_REG(port, TX_MFF_CTRL1)) & MFF_SET_MAC_RST)
+ goto reset_ok;
+ udelay(1);
+ }
+
+ netdev_warn(dev, "genesis reset failed\n");
+
+ reset_ok:
+ /* Unreset the XMAC. */
+ skge_write16(hw, SK_REG(port, TX_MFF_CTRL1), MFF_CLR_MAC_RST);
+
+ /*
+ * Perform additional initialization for external PHYs,
+ * namely for the 1000baseTX cards that use the XMAC's
+ * GMII mode.
+ */
+ if (hw->phy_type != SK_PHY_XMAC) {
+ /* Take external Phy out of reset */
+ r = skge_read32(hw, B2_GP_IO);
+ if (port == 0)
+ r |= GP_DIR_0|GP_IO_0;
+ else
+ r |= GP_DIR_2|GP_IO_2;
+
+ skge_write32(hw, B2_GP_IO, r);
+
+ /* Enable GMII interface */
+ xm_write16(hw, port, XM_HW_CFG, XM_HW_GMII_MD);
+ }
+
+
+ switch (hw->phy_type) {
+ case SK_PHY_XMAC:
+ xm_phy_init(skge);
+ break;
+ case SK_PHY_BCOM:
+ bcom_phy_init(skge);
+ bcom_check_link(hw, port);
+ }
+
+ /* Set Station Address */
+ xm_outaddr(hw, port, XM_SA, dev->dev_addr);
+
+ /* We don't use match addresses so clear */
+ for (i = 1; i < 16; i++)
+ xm_outaddr(hw, port, XM_EXM(i), zero);
+
+ /* Clear MIB counters */
+ xm_write16(hw, port, XM_STAT_CMD,
+ XM_SC_CLR_RXC | XM_SC_CLR_TXC);
+ /* Clear two times according to Errata #3 */
+ xm_write16(hw, port, XM_STAT_CMD,
+ XM_SC_CLR_RXC | XM_SC_CLR_TXC);
+
+ /* configure Rx High Water Mark (XM_RX_HI_WM) */
+ xm_write16(hw, port, XM_RX_HI_WM, 1450);
+
+ /* We don't need the FCS appended to the packet. */
+ r = XM_RX_LENERR_OK | XM_RX_STRIP_FCS;
+ if (jumbo)
+ r |= XM_RX_BIG_PK_OK;
+
+ if (skge->duplex == DUPLEX_HALF) {
+ /*
+ * If in manual half duplex mode the other side might be in
+ * full duplex mode, so ignore if a carrier extension is not seen
+ * on frames received
+ */
+ r |= XM_RX_DIS_CEXT;
+ }
+ xm_write16(hw, port, XM_RX_CMD, r);
+
+ /* We want short frames padded to 60 bytes. */
+ xm_write16(hw, port, XM_TX_CMD, XM_TX_AUTO_PAD);
+
+ /* Increase threshold for jumbo frames on dual port */
+ if (hw->ports > 1 && jumbo)
+ xm_write16(hw, port, XM_TX_THR, 1020);
+ else
+ xm_write16(hw, port, XM_TX_THR, 512);
+
+ /*
+ * Enable the reception of all error frames. This is is
+ * a necessary evil due to the design of the XMAC. The
+ * XMAC's receive FIFO is only 8K in size, however jumbo
+ * frames can be up to 9000 bytes in length. When bad
+ * frame filtering is enabled, the XMAC's RX FIFO operates
+ * in 'store and forward' mode. For this to work, the
+ * entire frame has to fit into the FIFO, but that means
+ * that jumbo frames larger than 8192 bytes will be
+ * truncated. Disabling all bad frame filtering causes
+ * the RX FIFO to operate in streaming mode, in which
+ * case the XMAC will start transferring frames out of the
+ * RX FIFO as soon as the FIFO threshold is reached.
+ */
+ xm_write32(hw, port, XM_MODE, XM_DEF_MODE);
+
+
+ /*
+ * Initialize the Receive Counter Event Mask (XM_RX_EV_MSK)
+ * - Enable all bits excepting 'Octets Rx OK Low CntOv'
+ * and 'Octets Rx OK Hi Cnt Ov'.
+ */
+ xm_write32(hw, port, XM_RX_EV_MSK, XMR_DEF_MSK);
+
+ /*
+ * Initialize the Transmit Counter Event Mask (XM_TX_EV_MSK)
+ * - Enable all bits excepting 'Octets Tx OK Low CntOv'
+ * and 'Octets Tx OK Hi Cnt Ov'.
+ */
+ xm_write32(hw, port, XM_TX_EV_MSK, XMT_DEF_MSK);
+
+ /* Configure MAC arbiter */
+ skge_write16(hw, B3_MA_TO_CTRL, MA_RST_CLR);
+
+ /* configure timeout values */
+ skge_write8(hw, B3_MA_TOINI_RX1, 72);
+ skge_write8(hw, B3_MA_TOINI_RX2, 72);
+ skge_write8(hw, B3_MA_TOINI_TX1, 72);
+ skge_write8(hw, B3_MA_TOINI_TX2, 72);
+
+ skge_write8(hw, B3_MA_RCINI_RX1, 0);
+ skge_write8(hw, B3_MA_RCINI_RX2, 0);
+ skge_write8(hw, B3_MA_RCINI_TX1, 0);
+ skge_write8(hw, B3_MA_RCINI_TX2, 0);
+
+ /* Configure Rx MAC FIFO */
+ skge_write8(hw, SK_REG(port, RX_MFF_CTRL2), MFF_RST_CLR);
+ skge_write16(hw, SK_REG(port, RX_MFF_CTRL1), MFF_ENA_TIM_PAT);
+ skge_write8(hw, SK_REG(port, RX_MFF_CTRL2), MFF_ENA_OP_MD);
+
+ /* Configure Tx MAC FIFO */
+ skge_write8(hw, SK_REG(port, TX_MFF_CTRL2), MFF_RST_CLR);
+ skge_write16(hw, SK_REG(port, TX_MFF_CTRL1), MFF_TX_CTRL_DEF);
+ skge_write8(hw, SK_REG(port, TX_MFF_CTRL2), MFF_ENA_OP_MD);
+
+ if (jumbo) {
+ /* Enable frame flushing if jumbo frames used */
+ skge_write16(hw, SK_REG(port, RX_MFF_CTRL1), MFF_ENA_FLUSH);
+ } else {
+ /* enable timeout timers if normal frames */
+ skge_write16(hw, B3_PA_CTRL,
+ (port == 0) ? PA_ENA_TO_TX1 : PA_ENA_TO_TX2);
+ }
+}
+
+static void genesis_stop(struct skge_port *skge)
+{
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+ unsigned retries = 1000;
+ u16 cmd;
+
+ /* Disable Tx and Rx */
+ cmd = xm_read16(hw, port, XM_MMU_CMD);
+ cmd &= ~(XM_MMU_ENA_RX | XM_MMU_ENA_TX);
+ xm_write16(hw, port, XM_MMU_CMD, cmd);
+
+ genesis_reset(hw, port);
+
+ /* Clear Tx packet arbiter timeout IRQ */
+ skge_write16(hw, B3_PA_CTRL,
+ port == 0 ? PA_CLR_TO_TX1 : PA_CLR_TO_TX2);
+
+ /* Reset the MAC */
+ skge_write16(hw, SK_REG(port, TX_MFF_CTRL1), MFF_CLR_MAC_RST);
+ do {
+ skge_write16(hw, SK_REG(port, TX_MFF_CTRL1), MFF_SET_MAC_RST);
+ if (!(skge_read16(hw, SK_REG(port, TX_MFF_CTRL1)) & MFF_SET_MAC_RST))
+ break;
+ } while (--retries > 0);
+
+ /* For external PHYs there must be special handling */
+ if (hw->phy_type != SK_PHY_XMAC) {
+ u32 reg = skge_read32(hw, B2_GP_IO);
+ if (port == 0) {
+ reg |= GP_DIR_0;
+ reg &= ~GP_IO_0;
+ } else {
+ reg |= GP_DIR_2;
+ reg &= ~GP_IO_2;
+ }
+ skge_write32(hw, B2_GP_IO, reg);
+ skge_read32(hw, B2_GP_IO);
+ }
+
+ xm_write16(hw, port, XM_MMU_CMD,
+ xm_read16(hw, port, XM_MMU_CMD)
+ & ~(XM_MMU_ENA_RX | XM_MMU_ENA_TX));
+
+ xm_read16(hw, port, XM_MMU_CMD);
+}
+
+
+static void genesis_get_stats(struct skge_port *skge, u64 *data)
+{
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+ int i;
+ unsigned long timeout = jiffies + HZ;
+
+ xm_write16(hw, port,
+ XM_STAT_CMD, XM_SC_SNP_TXC | XM_SC_SNP_RXC);
+
+ /* wait for update to complete */
+ while (xm_read16(hw, port, XM_STAT_CMD)
+ & (XM_SC_SNP_TXC | XM_SC_SNP_RXC)) {
+ if (time_after(jiffies, timeout))
+ break;
+ udelay(10);
+ }
+
+ /* special case for 64 bit octet counter */
+ data[0] = (u64) xm_read32(hw, port, XM_TXO_OK_HI) << 32
+ | xm_read32(hw, port, XM_TXO_OK_LO);
+ data[1] = (u64) xm_read32(hw, port, XM_RXO_OK_HI) << 32
+ | xm_read32(hw, port, XM_RXO_OK_LO);
+
+ for (i = 2; i < ARRAY_SIZE(skge_stats); i++)
+ data[i] = xm_read32(hw, port, skge_stats[i].xmac_offset);
+}
+
+static void genesis_mac_intr(struct skge_hw *hw, int port)
+{
+ struct net_device *dev = hw->dev[port];
+ struct skge_port *skge = netdev_priv(dev);
+ u16 status = xm_read16(hw, port, XM_ISRC);
+
+ netif_printk(skge, intr, KERN_DEBUG, skge->netdev,
+ "mac interrupt status 0x%x\n", status);
+
+ if (hw->phy_type == SK_PHY_XMAC && (status & XM_IS_INP_ASS)) {
+ xm_link_down(hw, port);
+ mod_timer(&skge->link_timer, jiffies + 1);
+ }
+
+ if (status & XM_IS_TXF_UR) {
+ xm_write32(hw, port, XM_MODE, XM_MD_FTF);
+ ++dev->stats.tx_fifo_errors;
+ }
+}
+
+static void genesis_link_up(struct skge_port *skge)
+{
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+ u16 cmd, msk;
+ u32 mode;
+
+ cmd = xm_read16(hw, port, XM_MMU_CMD);
+
+ /*
+ * enabling pause frame reception is required for 1000BT
+ * because the XMAC is not reset if the link is going down
+ */
+ if (skge->flow_status == FLOW_STAT_NONE ||
+ skge->flow_status == FLOW_STAT_LOC_SEND)
+ /* Disable Pause Frame Reception */
+ cmd |= XM_MMU_IGN_PF;
+ else
+ /* Enable Pause Frame Reception */
+ cmd &= ~XM_MMU_IGN_PF;
+
+ xm_write16(hw, port, XM_MMU_CMD, cmd);
+
+ mode = xm_read32(hw, port, XM_MODE);
+ if (skge->flow_status == FLOW_STAT_SYMMETRIC ||
+ skge->flow_status == FLOW_STAT_LOC_SEND) {
+ /*
+ * Configure Pause Frame Generation
+ * Use internal and external Pause Frame Generation.
+ * Sending pause frames is edge triggered.
+ * Send a Pause frame with the maximum pause time if
+ * internal oder external FIFO full condition occurs.
+ * Send a zero pause time frame to re-start transmission.
+ */
+ /* XM_PAUSE_DA = '010000C28001' (default) */
+ /* XM_MAC_PTIME = 0xffff (maximum) */
+ /* remember this value is defined in big endian (!) */
+ xm_write16(hw, port, XM_MAC_PTIME, 0xffff);
+
+ mode |= XM_PAUSE_MODE;
+ skge_write16(hw, SK_REG(port, RX_MFF_CTRL1), MFF_ENA_PAUSE);
+ } else {
+ /*
+ * disable pause frame generation is required for 1000BT
+ * because the XMAC is not reset if the link is going down
+ */
+ /* Disable Pause Mode in Mode Register */
+ mode &= ~XM_PAUSE_MODE;
+
+ skge_write16(hw, SK_REG(port, RX_MFF_CTRL1), MFF_DIS_PAUSE);
+ }
+
+ xm_write32(hw, port, XM_MODE, mode);
+
+ /* Turn on detection of Tx underrun */
+ msk = xm_read16(hw, port, XM_IMSK);
+ msk &= ~XM_IS_TXF_UR;
+ xm_write16(hw, port, XM_IMSK, msk);
+
+ xm_read16(hw, port, XM_ISRC);
+
+ /* get MMU Command Reg. */
+ cmd = xm_read16(hw, port, XM_MMU_CMD);
+ if (hw->phy_type != SK_PHY_XMAC && skge->duplex == DUPLEX_FULL)
+ cmd |= XM_MMU_GMII_FD;
+
+ /*
+ * Workaround BCOM Errata (#10523) for all BCom Phys
+ * Enable Power Management after link up
+ */
+ if (hw->phy_type == SK_PHY_BCOM) {
+ xm_phy_write(hw, port, PHY_BCOM_AUX_CTRL,
+ xm_phy_read(hw, port, PHY_BCOM_AUX_CTRL)
+ & ~PHY_B_AC_DIS_PM);
+ xm_phy_write(hw, port, PHY_BCOM_INT_MASK, PHY_B_DEF_MSK);
+ }
+
+ /* enable Rx/Tx */
+ xm_write16(hw, port, XM_MMU_CMD,
+ cmd | XM_MMU_ENA_RX | XM_MMU_ENA_TX);
+ skge_link_up(skge);
+}
+
+
+static inline void bcom_phy_intr(struct skge_port *skge)
+{
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+ u16 isrc;
+
+ isrc = xm_phy_read(hw, port, PHY_BCOM_INT_STAT);
+ netif_printk(skge, intr, KERN_DEBUG, skge->netdev,
+ "phy interrupt status 0x%x\n", isrc);
+
+ if (isrc & PHY_B_IS_PSE)
+ pr_err("%s: uncorrectable pair swap error\n",
+ hw->dev[port]->name);
+
+ /* Workaround BCom Errata:
+ * enable and disable loopback mode if "NO HCD" occurs.
+ */
+ if (isrc & PHY_B_IS_NO_HDCL) {
+ u16 ctrl = xm_phy_read(hw, port, PHY_BCOM_CTRL);
+ xm_phy_write(hw, port, PHY_BCOM_CTRL,
+ ctrl | PHY_CT_LOOP);
+ xm_phy_write(hw, port, PHY_BCOM_CTRL,
+ ctrl & ~PHY_CT_LOOP);
+ }
+
+ if (isrc & (PHY_B_IS_AN_PR | PHY_B_IS_LST_CHANGE))
+ bcom_check_link(hw, port);
+
+}
+
+static int gm_phy_write(struct skge_hw *hw, int port, u16 reg, u16 val)
+{
+ int i;
+
+ gma_write16(hw, port, GM_SMI_DATA, val);
+ gma_write16(hw, port, GM_SMI_CTRL,
+ GM_SMI_CT_PHY_AD(hw->phy_addr) | GM_SMI_CT_REG_AD(reg));
+ for (i = 0; i < PHY_RETRIES; i++) {
+ udelay(1);
+
+ if (!(gma_read16(hw, port, GM_SMI_CTRL) & GM_SMI_CT_BUSY))
+ return 0;
+ }
+
+ pr_warn("%s: phy write timeout\n", hw->dev[port]->name);
+ return -EIO;
+}
+
+static int __gm_phy_read(struct skge_hw *hw, int port, u16 reg, u16 *val)
+{
+ int i;
+
+ gma_write16(hw, port, GM_SMI_CTRL,
+ GM_SMI_CT_PHY_AD(hw->phy_addr)
+ | GM_SMI_CT_REG_AD(reg) | GM_SMI_CT_OP_RD);
+
+ for (i = 0; i < PHY_RETRIES; i++) {
+ udelay(1);
+ if (gma_read16(hw, port, GM_SMI_CTRL) & GM_SMI_CT_RD_VAL)
+ goto ready;
+ }
+
+ return -ETIMEDOUT;
+ ready:
+ *val = gma_read16(hw, port, GM_SMI_DATA);
+ return 0;
+}
+
+static u16 gm_phy_read(struct skge_hw *hw, int port, u16 reg)
+{
+ u16 v = 0;
+ if (__gm_phy_read(hw, port, reg, &v))
+ pr_warn("%s: phy read timeout\n", hw->dev[port]->name);
+ return v;
+}
+
+/* Marvell Phy Initialization */
+static void yukon_init(struct skge_hw *hw, int port)
+{
+ struct skge_port *skge = netdev_priv(hw->dev[port]);
+ u16 ctrl, ct1000, adv;
+
+ if (skge->autoneg == AUTONEG_ENABLE) {
+ u16 ectrl = gm_phy_read(hw, port, PHY_MARV_EXT_CTRL);
+
+ ectrl &= ~(PHY_M_EC_M_DSC_MSK | PHY_M_EC_S_DSC_MSK |
+ PHY_M_EC_MAC_S_MSK);
+ ectrl |= PHY_M_EC_MAC_S(MAC_TX_CLK_25_MHZ);
+
+ ectrl |= PHY_M_EC_M_DSC(0) | PHY_M_EC_S_DSC(1);
+
+ gm_phy_write(hw, port, PHY_MARV_EXT_CTRL, ectrl);
+ }
+
+ ctrl = gm_phy_read(hw, port, PHY_MARV_CTRL);
+ if (skge->autoneg == AUTONEG_DISABLE)
+ ctrl &= ~PHY_CT_ANE;
+
+ ctrl |= PHY_CT_RESET;
+ gm_phy_write(hw, port, PHY_MARV_CTRL, ctrl);
+
+ ctrl = 0;
+ ct1000 = 0;
+ adv = PHY_AN_CSMA;
+
+ if (skge->autoneg == AUTONEG_ENABLE) {
+ if (hw->copper) {
+ if (skge->advertising & ADVERTISED_1000baseT_Full)
+ ct1000 |= PHY_M_1000C_AFD;
+ if (skge->advertising & ADVERTISED_1000baseT_Half)
+ ct1000 |= PHY_M_1000C_AHD;
+ if (skge->advertising & ADVERTISED_100baseT_Full)
+ adv |= PHY_M_AN_100_FD;
+ if (skge->advertising & ADVERTISED_100baseT_Half)
+ adv |= PHY_M_AN_100_HD;
+ if (skge->advertising & ADVERTISED_10baseT_Full)
+ adv |= PHY_M_AN_10_FD;
+ if (skge->advertising & ADVERTISED_10baseT_Half)
+ adv |= PHY_M_AN_10_HD;
+
+ /* Set Flow-control capabilities */
+ adv |= phy_pause_map[skge->flow_control];
+ } else {
+ if (skge->advertising & ADVERTISED_1000baseT_Full)
+ adv |= PHY_M_AN_1000X_AFD;
+ if (skge->advertising & ADVERTISED_1000baseT_Half)
+ adv |= PHY_M_AN_1000X_AHD;
+
+ adv |= fiber_pause_map[skge->flow_control];
+ }
+
+ /* Restart Auto-negotiation */
+ ctrl |= PHY_CT_ANE | PHY_CT_RE_CFG;
+ } else {
+ /* forced speed/duplex settings */
+ ct1000 = PHY_M_1000C_MSE;
+
+ if (skge->duplex == DUPLEX_FULL)
+ ctrl |= PHY_CT_DUP_MD;
+
+ switch (skge->speed) {
+ case SPEED_1000:
+ ctrl |= PHY_CT_SP1000;
+ break;
+ case SPEED_100:
+ ctrl |= PHY_CT_SP100;
+ break;
+ }
+
+ ctrl |= PHY_CT_RESET;
+ }
+
+ gm_phy_write(hw, port, PHY_MARV_1000T_CTRL, ct1000);
+
+ gm_phy_write(hw, port, PHY_MARV_AUNE_ADV, adv);
+ gm_phy_write(hw, port, PHY_MARV_CTRL, ctrl);
+
+ /* Enable phy interrupt on autonegotiation complete (or link up) */
+ if (skge->autoneg == AUTONEG_ENABLE)
+ gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_IS_AN_MSK);
+ else
+ gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_IS_DEF_MSK);
+}
+
+static void yukon_reset(struct skge_hw *hw, int port)
+{
+ gm_phy_write(hw, port, PHY_MARV_INT_MASK, 0);/* disable PHY IRQs */
+ gma_write16(hw, port, GM_MC_ADDR_H1, 0); /* clear MC hash */
+ gma_write16(hw, port, GM_MC_ADDR_H2, 0);
+ gma_write16(hw, port, GM_MC_ADDR_H3, 0);
+ gma_write16(hw, port, GM_MC_ADDR_H4, 0);
+
+ gma_write16(hw, port, GM_RX_CTRL,
+ gma_read16(hw, port, GM_RX_CTRL)
+ | GM_RXCR_UCF_ENA | GM_RXCR_MCF_ENA);
+}
+
+/* Apparently, early versions of Yukon-Lite had wrong chip_id? */
+static int is_yukon_lite_a0(struct skge_hw *hw)
+{
+ u32 reg;
+ int ret;
+
+ if (hw->chip_id != CHIP_ID_YUKON)
+ return 0;
+
+ reg = skge_read32(hw, B2_FAR);
+ skge_write8(hw, B2_FAR + 3, 0xff);
+ ret = (skge_read8(hw, B2_FAR + 3) != 0);
+ skge_write32(hw, B2_FAR, reg);
+ return ret;
+}
+
+static void yukon_mac_init(struct skge_hw *hw, int port)
+{
+ struct skge_port *skge = netdev_priv(hw->dev[port]);
+ int i;
+ u32 reg;
+ const u8 *addr = hw->dev[port]->dev_addr;
+
+ /* WA code for COMA mode -- set PHY reset */
+ if (hw->chip_id == CHIP_ID_YUKON_LITE &&
+ hw->chip_rev >= CHIP_REV_YU_LITE_A3) {
+ reg = skge_read32(hw, B2_GP_IO);
+ reg |= GP_DIR_9 | GP_IO_9;
+ skge_write32(hw, B2_GP_IO, reg);
+ }
+
+ /* hard reset */
+ skge_write32(hw, SK_REG(port, GPHY_CTRL), GPC_RST_SET);
+ skge_write32(hw, SK_REG(port, GMAC_CTRL), GMC_RST_SET);
+
+ /* WA code for COMA mode -- clear PHY reset */
+ if (hw->chip_id == CHIP_ID_YUKON_LITE &&
+ hw->chip_rev >= CHIP_REV_YU_LITE_A3) {
+ reg = skge_read32(hw, B2_GP_IO);
+ reg |= GP_DIR_9;
+ reg &= ~GP_IO_9;
+ skge_write32(hw, B2_GP_IO, reg);
+ }
+
+ /* Set hardware config mode */
+ reg = GPC_INT_POL_HI | GPC_DIS_FC | GPC_DIS_SLEEP |
+ GPC_ENA_XC | GPC_ANEG_ADV_ALL_M | GPC_ENA_PAUSE;
+ reg |= hw->copper ? GPC_HWCFG_GMII_COP : GPC_HWCFG_GMII_FIB;
+
+ /* Clear GMC reset */
+ skge_write32(hw, SK_REG(port, GPHY_CTRL), reg | GPC_RST_SET);
+ skge_write32(hw, SK_REG(port, GPHY_CTRL), reg | GPC_RST_CLR);
+ skge_write32(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_ON | GMC_RST_CLR);
+
+ if (skge->autoneg == AUTONEG_DISABLE) {
+ reg = GM_GPCR_AU_ALL_DIS;
+ gma_write16(hw, port, GM_GP_CTRL,
+ gma_read16(hw, port, GM_GP_CTRL) | reg);
+
+ switch (skge->speed) {
+ case SPEED_1000:
+ reg &= ~GM_GPCR_SPEED_100;
+ reg |= GM_GPCR_SPEED_1000;
+ break;
+ case SPEED_100:
+ reg &= ~GM_GPCR_SPEED_1000;
+ reg |= GM_GPCR_SPEED_100;
+ break;
+ case SPEED_10:
+ reg &= ~(GM_GPCR_SPEED_1000 | GM_GPCR_SPEED_100);
+ break;
+ }
+
+ if (skge->duplex == DUPLEX_FULL)
+ reg |= GM_GPCR_DUP_FULL;
+ } else
+ reg = GM_GPCR_SPEED_1000 | GM_GPCR_SPEED_100 | GM_GPCR_DUP_FULL;
+
+ switch (skge->flow_control) {
+ case FLOW_MODE_NONE:
+ skge_write32(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_OFF);
+ reg |= GM_GPCR_FC_TX_DIS | GM_GPCR_FC_RX_DIS | GM_GPCR_AU_FCT_DIS;
+ break;
+ case FLOW_MODE_LOC_SEND:
+ /* disable Rx flow-control */
+ reg |= GM_GPCR_FC_RX_DIS | GM_GPCR_AU_FCT_DIS;
+ break;
+ case FLOW_MODE_SYMMETRIC:
+ case FLOW_MODE_SYM_OR_REM:
+ /* enable Tx & Rx flow-control */
+ break;
+ }
+
+ gma_write16(hw, port, GM_GP_CTRL, reg);
+ skge_read16(hw, SK_REG(port, GMAC_IRQ_SRC));
+
+ yukon_init(hw, port);
+
+ /* MIB clear */
+ reg = gma_read16(hw, port, GM_PHY_ADDR);
+ gma_write16(hw, port, GM_PHY_ADDR, reg | GM_PAR_MIB_CLR);
+
+ for (i = 0; i < GM_MIB_CNT_SIZE; i++)
+ gma_read16(hw, port, GM_MIB_CNT_BASE + 8*i);
+ gma_write16(hw, port, GM_PHY_ADDR, reg);
+
+ /* transmit control */
+ gma_write16(hw, port, GM_TX_CTRL, TX_COL_THR(TX_COL_DEF));
+
+ /* receive control reg: unicast + multicast + no FCS */
+ gma_write16(hw, port, GM_RX_CTRL,
+ GM_RXCR_UCF_ENA | GM_RXCR_CRC_DIS | GM_RXCR_MCF_ENA);
+
+ /* transmit flow control */
+ gma_write16(hw, port, GM_TX_FLOW_CTRL, 0xffff);
+
+ /* transmit parameter */
+ gma_write16(hw, port, GM_TX_PARAM,
+ TX_JAM_LEN_VAL(TX_JAM_LEN_DEF) |
+ TX_JAM_IPG_VAL(TX_JAM_IPG_DEF) |
+ TX_IPG_JAM_DATA(TX_IPG_JAM_DEF));
+
+ /* configure the Serial Mode Register */
+ reg = DATA_BLIND_VAL(DATA_BLIND_DEF)
+ | GM_SMOD_VLAN_ENA
+ | IPG_DATA_VAL(IPG_DATA_DEF);
+
+ if (hw->dev[port]->mtu > ETH_DATA_LEN)
+ reg |= GM_SMOD_JUMBO_ENA;
+
+ gma_write16(hw, port, GM_SERIAL_MODE, reg);
+
+ /* physical address: used for pause frames */
+ gma_set_addr(hw, port, GM_SRC_ADDR_1L, addr);
+ /* virtual address for data */
+ gma_set_addr(hw, port, GM_SRC_ADDR_2L, addr);
+
+ /* enable interrupt mask for counter overflows */
+ gma_write16(hw, port, GM_TX_IRQ_MSK, 0);
+ gma_write16(hw, port, GM_RX_IRQ_MSK, 0);
+ gma_write16(hw, port, GM_TR_IRQ_MSK, 0);
+
+ /* Initialize Mac Fifo */
+
+ /* Configure Rx MAC FIFO */
+ skge_write16(hw, SK_REG(port, RX_GMF_FL_MSK), RX_FF_FL_DEF_MSK);
+ reg = GMF_OPER_ON | GMF_RX_F_FL_ON;
+
+ /* disable Rx GMAC FIFO Flush for YUKON-Lite Rev. A0 only */
+ if (is_yukon_lite_a0(hw))
+ reg &= ~GMF_RX_F_FL_ON;
+
+ skge_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RST_CLR);
+ skge_write16(hw, SK_REG(port, RX_GMF_CTRL_T), reg);
+ /*
+ * because Pause Packet Truncation in GMAC is not working
+ * we have to increase the Flush Threshold to 64 bytes
+ * in order to flush pause packets in Rx FIFO on Yukon-1
+ */
+ skge_write16(hw, SK_REG(port, RX_GMF_FL_THR), RX_GMF_FL_THR_DEF+1);
+
+ /* Configure Tx MAC FIFO */
+ skge_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_RST_CLR);
+ skge_write16(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_OPER_ON);
+}
+
+/* Go into power down mode */
+static void yukon_suspend(struct skge_hw *hw, int port)
+{
+ u16 ctrl;
+
+ ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL);
+ ctrl |= PHY_M_PC_POL_R_DIS;
+ gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl);
+
+ ctrl = gm_phy_read(hw, port, PHY_MARV_CTRL);
+ ctrl |= PHY_CT_RESET;
+ gm_phy_write(hw, port, PHY_MARV_CTRL, ctrl);
+
+ /* switch IEEE compatible power down mode on */
+ ctrl = gm_phy_read(hw, port, PHY_MARV_CTRL);
+ ctrl |= PHY_CT_PDOWN;
+ gm_phy_write(hw, port, PHY_MARV_CTRL, ctrl);
+}
+
+static void yukon_stop(struct skge_port *skge)
+{
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+
+ skge_write8(hw, SK_REG(port, GMAC_IRQ_MSK), 0);
+ yukon_reset(hw, port);
+
+ gma_write16(hw, port, GM_GP_CTRL,
+ gma_read16(hw, port, GM_GP_CTRL)
+ & ~(GM_GPCR_TX_ENA|GM_GPCR_RX_ENA));
+ gma_read16(hw, port, GM_GP_CTRL);
+
+ yukon_suspend(hw, port);
+
+ /* set GPHY Control reset */
+ skge_write8(hw, SK_REG(port, GPHY_CTRL), GPC_RST_SET);
+ skge_write8(hw, SK_REG(port, GMAC_CTRL), GMC_RST_SET);
+}
+
+static void yukon_get_stats(struct skge_port *skge, u64 *data)
+{
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+ int i;
+
+ data[0] = (u64) gma_read32(hw, port, GM_TXO_OK_HI) << 32
+ | gma_read32(hw, port, GM_TXO_OK_LO);
+ data[1] = (u64) gma_read32(hw, port, GM_RXO_OK_HI) << 32
+ | gma_read32(hw, port, GM_RXO_OK_LO);
+
+ for (i = 2; i < ARRAY_SIZE(skge_stats); i++)
+ data[i] = gma_read32(hw, port,
+ skge_stats[i].gma_offset);
+}
+
+static void yukon_mac_intr(struct skge_hw *hw, int port)
+{
+ struct net_device *dev = hw->dev[port];
+ struct skge_port *skge = netdev_priv(dev);
+ u8 status = skge_read8(hw, SK_REG(port, GMAC_IRQ_SRC));
+
+ netif_printk(skge, intr, KERN_DEBUG, skge->netdev,
+ "mac interrupt status 0x%x\n", status);
+
+ if (status & GM_IS_RX_FF_OR) {
+ ++dev->stats.rx_fifo_errors;
+ skge_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_CLI_RX_FO);
+ }
+
+ if (status & GM_IS_TX_FF_UR) {
+ ++dev->stats.tx_fifo_errors;
+ skge_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_CLI_TX_FU);
+ }
+
+}
+
+static u16 yukon_speed(const struct skge_hw *hw, u16 aux)
+{
+ switch (aux & PHY_M_PS_SPEED_MSK) {
+ case PHY_M_PS_SPEED_1000:
+ return SPEED_1000;
+ case PHY_M_PS_SPEED_100:
+ return SPEED_100;
+ default:
+ return SPEED_10;
+ }
+}
+
+static void yukon_link_up(struct skge_port *skge)
+{
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+ u16 reg;
+
+ /* Enable Transmit FIFO Underrun */
+ skge_write8(hw, SK_REG(port, GMAC_IRQ_MSK), GMAC_DEF_MSK);
+
+ reg = gma_read16(hw, port, GM_GP_CTRL);
+ if (skge->duplex == DUPLEX_FULL || skge->autoneg == AUTONEG_ENABLE)
+ reg |= GM_GPCR_DUP_FULL;
+
+ /* enable Rx/Tx */
+ reg |= GM_GPCR_RX_ENA | GM_GPCR_TX_ENA;
+ gma_write16(hw, port, GM_GP_CTRL, reg);
+
+ gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_IS_DEF_MSK);
+ skge_link_up(skge);
+}
+
+static void yukon_link_down(struct skge_port *skge)
+{
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+ u16 ctrl;
+
+ ctrl = gma_read16(hw, port, GM_GP_CTRL);
+ ctrl &= ~(GM_GPCR_RX_ENA | GM_GPCR_TX_ENA);
+ gma_write16(hw, port, GM_GP_CTRL, ctrl);
+
+ if (skge->flow_status == FLOW_STAT_REM_SEND) {
+ ctrl = gm_phy_read(hw, port, PHY_MARV_AUNE_ADV);
+ ctrl |= PHY_M_AN_ASP;
+ /* restore Asymmetric Pause bit */
+ gm_phy_write(hw, port, PHY_MARV_AUNE_ADV, ctrl);
+ }
+
+ skge_link_down(skge);
+
+ yukon_init(hw, port);
+}
+
+static void yukon_phy_intr(struct skge_port *skge)
+{
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+ const char *reason = NULL;
+ u16 istatus, phystat;
+
+ istatus = gm_phy_read(hw, port, PHY_MARV_INT_STAT);
+ phystat = gm_phy_read(hw, port, PHY_MARV_PHY_STAT);
+
+ netif_printk(skge, intr, KERN_DEBUG, skge->netdev,
+ "phy interrupt status 0x%x 0x%x\n", istatus, phystat);
+
+ if (istatus & PHY_M_IS_AN_COMPL) {
+ if (gm_phy_read(hw, port, PHY_MARV_AUNE_LP)
+ & PHY_M_AN_RF) {
+ reason = "remote fault";
+ goto failed;
+ }
+
+ if (gm_phy_read(hw, port, PHY_MARV_1000T_STAT) & PHY_B_1000S_MSF) {
+ reason = "master/slave fault";
+ goto failed;
+ }
+
+ if (!(phystat & PHY_M_PS_SPDUP_RES)) {
+ reason = "speed/duplex";
+ goto failed;
+ }
+
+ skge->duplex = (phystat & PHY_M_PS_FULL_DUP)
+ ? DUPLEX_FULL : DUPLEX_HALF;
+ skge->speed = yukon_speed(hw, phystat);
+
+ /* We are using IEEE 802.3z/D5.0 Table 37-4 */
+ switch (phystat & PHY_M_PS_PAUSE_MSK) {
+ case PHY_M_PS_PAUSE_MSK:
+ skge->flow_status = FLOW_STAT_SYMMETRIC;
+ break;
+ case PHY_M_PS_RX_P_EN:
+ skge->flow_status = FLOW_STAT_REM_SEND;
+ break;
+ case PHY_M_PS_TX_P_EN:
+ skge->flow_status = FLOW_STAT_LOC_SEND;
+ break;
+ default:
+ skge->flow_status = FLOW_STAT_NONE;
+ }
+
+ if (skge->flow_status == FLOW_STAT_NONE ||
+ (skge->speed < SPEED_1000 && skge->duplex == DUPLEX_HALF))
+ skge_write8(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_OFF);
+ else
+ skge_write8(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_ON);
+ yukon_link_up(skge);
+ return;
+ }
+
+ if (istatus & PHY_M_IS_LSP_CHANGE)
+ skge->speed = yukon_speed(hw, phystat);
+
+ if (istatus & PHY_M_IS_DUP_CHANGE)
+ skge->duplex = (phystat & PHY_M_PS_FULL_DUP) ? DUPLEX_FULL : DUPLEX_HALF;
+ if (istatus & PHY_M_IS_LST_CHANGE) {
+ if (phystat & PHY_M_PS_LINK_UP)
+ yukon_link_up(skge);
+ else
+ yukon_link_down(skge);
+ }
+ return;
+ failed:
+ pr_err("%s: autonegotiation failed (%s)\n", skge->netdev->name, reason);
+
+ /* XXX restart autonegotiation? */
+}
+
+static void skge_phy_reset(struct skge_port *skge)
+{
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+ struct net_device *dev = hw->dev[port];
+
+ netif_stop_queue(skge->netdev);
+ netif_carrier_off(skge->netdev);
+
+ spin_lock_bh(&hw->phy_lock);
+ if (is_genesis(hw)) {
+ genesis_reset(hw, port);
+ genesis_mac_init(hw, port);
+ } else {
+ yukon_reset(hw, port);
+ yukon_init(hw, port);
+ }
+ spin_unlock_bh(&hw->phy_lock);
+
+ skge_set_multicast(dev);
+}
+
+/* Basic MII support */
+static int skge_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd)
+{
+ struct mii_ioctl_data *data = if_mii(ifr);
+ struct skge_port *skge = netdev_priv(dev);
+ struct skge_hw *hw = skge->hw;
+ int err = -EOPNOTSUPP;
+
+ if (!netif_running(dev))
+ return -ENODEV; /* Phy still in reset */
+
+ switch (cmd) {
+ case SIOCGMIIPHY:
+ data->phy_id = hw->phy_addr;
+
+ /* fallthru */
+ case SIOCGMIIREG: {
+ u16 val = 0;
+ spin_lock_bh(&hw->phy_lock);
+
+ if (is_genesis(hw))
+ err = __xm_phy_read(hw, skge->port, data->reg_num & 0x1f, &val);
+ else
+ err = __gm_phy_read(hw, skge->port, data->reg_num & 0x1f, &val);
+ spin_unlock_bh(&hw->phy_lock);
+ data->val_out = val;
+ break;
+ }
+
+ case SIOCSMIIREG:
+ spin_lock_bh(&hw->phy_lock);
+ if (is_genesis(hw))
+ err = xm_phy_write(hw, skge->port, data->reg_num & 0x1f,
+ data->val_in);
+ else
+ err = gm_phy_write(hw, skge->port, data->reg_num & 0x1f,
+ data->val_in);
+ spin_unlock_bh(&hw->phy_lock);
+ break;
+ }
+ return err;
+}
+
+static void skge_ramset(struct skge_hw *hw, u16 q, u32 start, size_t len)
+{
+ u32 end;
+
+ start /= 8;
+ len /= 8;
+ end = start + len - 1;
+
+ skge_write8(hw, RB_ADDR(q, RB_CTRL), RB_RST_CLR);
+ skge_write32(hw, RB_ADDR(q, RB_START), start);
+ skge_write32(hw, RB_ADDR(q, RB_WP), start);
+ skge_write32(hw, RB_ADDR(q, RB_RP), start);
+ skge_write32(hw, RB_ADDR(q, RB_END), end);
+
+ if (q == Q_R1 || q == Q_R2) {
+ /* Set thresholds on receive queue's */
+ skge_write32(hw, RB_ADDR(q, RB_RX_UTPP),
+ start + (2*len)/3);
+ skge_write32(hw, RB_ADDR(q, RB_RX_LTPP),
+ start + (len/3));
+ } else {
+ /* Enable store & forward on Tx queue's because
+ * Tx FIFO is only 4K on Genesis and 1K on Yukon
+ */
+ skge_write8(hw, RB_ADDR(q, RB_CTRL), RB_ENA_STFWD);
+ }
+
+ skge_write8(hw, RB_ADDR(q, RB_CTRL), RB_ENA_OP_MD);
+}
+
+/* Setup Bus Memory Interface */
+static void skge_qset(struct skge_port *skge, u16 q,
+ const struct skge_element *e)
+{
+ struct skge_hw *hw = skge->hw;
+ u32 watermark = 0x600;
+ u64 base = skge->dma + (e->desc - skge->mem);
+
+ /* optimization to reduce window on 32bit/33mhz */
+ if ((skge_read16(hw, B0_CTST) & (CS_BUS_CLOCK | CS_BUS_SLOT_SZ)) == 0)
+ watermark /= 2;
+
+ skge_write32(hw, Q_ADDR(q, Q_CSR), CSR_CLR_RESET);
+ skge_write32(hw, Q_ADDR(q, Q_F), watermark);
+ skge_write32(hw, Q_ADDR(q, Q_DA_H), (u32)(base >> 32));
+ skge_write32(hw, Q_ADDR(q, Q_DA_L), (u32)base);
+}
+
+static int skge_up(struct net_device *dev)
+{
+ struct skge_port *skge = netdev_priv(dev);
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+ u32 chunk, ram_addr;
+ size_t rx_size, tx_size;
+ int err;
+
+ if (!is_valid_ether_addr(dev->dev_addr))
+ return -EINVAL;
+
+ netif_info(skge, ifup, skge->netdev, "enabling interface\n");
+
+ if (dev->mtu > RX_BUF_SIZE)
+ skge->rx_buf_size = dev->mtu + ETH_HLEN;
+ else
+ skge->rx_buf_size = RX_BUF_SIZE;
+
+
+ rx_size = skge->rx_ring.count * sizeof(struct skge_rx_desc);
+ tx_size = skge->tx_ring.count * sizeof(struct skge_tx_desc);
+ skge->mem_size = tx_size + rx_size;
+ skge->mem = pci_alloc_consistent(hw->pdev, skge->mem_size, &skge->dma);
+ if (!skge->mem)
+ return -ENOMEM;
+
+ BUG_ON(skge->dma & 7);
+
+ if (upper_32_bits(skge->dma) != upper_32_bits(skge->dma + skge->mem_size)) {
+ dev_err(&hw->pdev->dev, "pci_alloc_consistent region crosses 4G boundary\n");
+ err = -EINVAL;
+ goto free_pci_mem;
+ }
+
+ memset(skge->mem, 0, skge->mem_size);
+
+ err = skge_ring_alloc(&skge->rx_ring, skge->mem, skge->dma);
+ if (err)
+ goto free_pci_mem;
+
+ err = skge_rx_fill(dev);
+ if (err)
+ goto free_rx_ring;
+
+ err = skge_ring_alloc(&skge->tx_ring, skge->mem + rx_size,
+ skge->dma + rx_size);
+ if (err)
+ goto free_rx_ring;
+
+ if (hw->ports == 1) {
+ err = request_irq(hw->pdev->irq, skge_intr, IRQF_SHARED,
+ dev->name, hw);
+ if (err) {
+ netdev_err(dev, "Unable to allocate interrupt %d error: %d\n",
+ hw->pdev->irq, err);
+ goto free_tx_ring;
+ }
+ }
+
+ /* Initialize MAC */
+ netif_carrier_off(dev);
+ spin_lock_bh(&hw->phy_lock);
+ if (is_genesis(hw))
+ genesis_mac_init(hw, port);
+ else
+ yukon_mac_init(hw, port);
+ spin_unlock_bh(&hw->phy_lock);
+
+ /* Configure RAMbuffers - equally between ports and tx/rx */
+ chunk = (hw->ram_size - hw->ram_offset) / (hw->ports * 2);
+ ram_addr = hw->ram_offset + 2 * chunk * port;
+
+ skge_ramset(hw, rxqaddr[port], ram_addr, chunk);
+ skge_qset(skge, rxqaddr[port], skge->rx_ring.to_clean);
+
+ BUG_ON(skge->tx_ring.to_use != skge->tx_ring.to_clean);
+ skge_ramset(hw, txqaddr[port], ram_addr+chunk, chunk);
+ skge_qset(skge, txqaddr[port], skge->tx_ring.to_use);
+
+ /* Start receiver BMU */
+ wmb();
+ skge_write8(hw, Q_ADDR(rxqaddr[port], Q_CSR), CSR_START | CSR_IRQ_CL_F);
+ skge_led(skge, LED_MODE_ON);
+
+ spin_lock_irq(&hw->hw_lock);
+ hw->intr_mask |= portmask[port];
+ skge_write32(hw, B0_IMSK, hw->intr_mask);
+ skge_read32(hw, B0_IMSK);
+ spin_unlock_irq(&hw->hw_lock);
+
+ napi_enable(&skge->napi);
+
+ skge_set_multicast(dev);
+
+ return 0;
+
+ free_tx_ring:
+ kfree(skge->tx_ring.start);
+ free_rx_ring:
+ skge_rx_clean(skge);
+ kfree(skge->rx_ring.start);
+ free_pci_mem:
+ pci_free_consistent(hw->pdev, skge->mem_size, skge->mem, skge->dma);
+ skge->mem = NULL;
+
+ return err;
+}
+
+/* stop receiver */
+static void skge_rx_stop(struct skge_hw *hw, int port)
+{
+ skge_write8(hw, Q_ADDR(rxqaddr[port], Q_CSR), CSR_STOP);
+ skge_write32(hw, RB_ADDR(port ? Q_R2 : Q_R1, RB_CTRL),
+ RB_RST_SET|RB_DIS_OP_MD);
+ skge_write32(hw, Q_ADDR(rxqaddr[port], Q_CSR), CSR_SET_RESET);
+}
+
+static int skge_down(struct net_device *dev)
+{
+ struct skge_port *skge = netdev_priv(dev);
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+
+ if (skge->mem == NULL)
+ return 0;
+
+ netif_info(skge, ifdown, skge->netdev, "disabling interface\n");
+
+ netif_tx_disable(dev);
+
+ if (is_genesis(hw) && hw->phy_type == SK_PHY_XMAC)
+ del_timer_sync(&skge->link_timer);
+
+ napi_disable(&skge->napi);
+ netif_carrier_off(dev);
+
+ spin_lock_irq(&hw->hw_lock);
+ hw->intr_mask &= ~portmask[port];
+ skge_write32(hw, B0_IMSK, (hw->ports == 1) ? 0 : hw->intr_mask);
+ skge_read32(hw, B0_IMSK);
+ spin_unlock_irq(&hw->hw_lock);
+
+ if (hw->ports == 1)
+ free_irq(hw->pdev->irq, hw);
+
+ skge_write8(skge->hw, SK_REG(skge->port, LNK_LED_REG), LED_OFF);
+ if (is_genesis(hw))
+ genesis_stop(skge);
+ else
+ yukon_stop(skge);
+
+ /* Stop transmitter */
+ skge_write8(hw, Q_ADDR(txqaddr[port], Q_CSR), CSR_STOP);
+ skge_write32(hw, RB_ADDR(txqaddr[port], RB_CTRL),
+ RB_RST_SET|RB_DIS_OP_MD);
+
+
+ /* Disable Force Sync bit and Enable Alloc bit */
+ skge_write8(hw, SK_REG(port, TXA_CTRL),
+ TXA_DIS_FSYNC | TXA_DIS_ALLOC | TXA_STOP_RC);
+
+ /* Stop Interval Timer and Limit Counter of Tx Arbiter */
+ skge_write32(hw, SK_REG(port, TXA_ITI_INI), 0L);
+ skge_write32(hw, SK_REG(port, TXA_LIM_INI), 0L);
+
+ /* Reset PCI FIFO */
+ skge_write32(hw, Q_ADDR(txqaddr[port], Q_CSR), CSR_SET_RESET);
+ skge_write32(hw, RB_ADDR(txqaddr[port], RB_CTRL), RB_RST_SET);
+
+ /* Reset the RAM Buffer async Tx queue */
+ skge_write8(hw, RB_ADDR(port == 0 ? Q_XA1 : Q_XA2, RB_CTRL), RB_RST_SET);
+
+ skge_rx_stop(hw, port);
+
+ if (is_genesis(hw)) {
+ skge_write8(hw, SK_REG(port, TX_MFF_CTRL2), MFF_RST_SET);
+ skge_write8(hw, SK_REG(port, RX_MFF_CTRL2), MFF_RST_SET);
+ } else {
+ skge_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RST_SET);
+ skge_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_RST_SET);
+ }
+
+ skge_led(skge, LED_MODE_OFF);
+
+ netif_tx_lock_bh(dev);
+ skge_tx_clean(dev);
+ netif_tx_unlock_bh(dev);
+
+ skge_rx_clean(skge);
+
+ kfree(skge->rx_ring.start);
+ kfree(skge->tx_ring.start);
+ pci_free_consistent(hw->pdev, skge->mem_size, skge->mem, skge->dma);
+ skge->mem = NULL;
+ return 0;
+}
+
+static inline int skge_avail(const struct skge_ring *ring)
+{
+ smp_mb();
+ return ((ring->to_clean > ring->to_use) ? 0 : ring->count)
+ + (ring->to_clean - ring->to_use) - 1;
+}
+
+static netdev_tx_t skge_xmit_frame(struct sk_buff *skb,
+ struct net_device *dev)
+{
+ struct skge_port *skge = netdev_priv(dev);
+ struct skge_hw *hw = skge->hw;
+ struct skge_element *e;
+ struct skge_tx_desc *td;
+ int i;
+ u32 control, len;
+ dma_addr_t map;
+
+ if (skb_padto(skb, ETH_ZLEN))
+ return NETDEV_TX_OK;
+
+ if (unlikely(skge_avail(&skge->tx_ring) < skb_shinfo(skb)->nr_frags + 1))
+ return NETDEV_TX_BUSY;
+
+ e = skge->tx_ring.to_use;
+ td = e->desc;
+ BUG_ON(td->control & BMU_OWN);
+ e->skb = skb;
+ len = skb_headlen(skb);
+ map = pci_map_single(hw->pdev, skb->data, len, PCI_DMA_TODEVICE);
+ if (pci_dma_mapping_error(hw->pdev, map))
+ goto mapping_error;
+
+ dma_unmap_addr_set(e, mapaddr, map);
+ dma_unmap_len_set(e, maplen, len);
+
+ td->dma_lo = lower_32_bits(map);
+ td->dma_hi = upper_32_bits(map);
+
+ if (skb->ip_summed == CHECKSUM_PARTIAL) {
+ const int offset = skb_checksum_start_offset(skb);
+
+ /* This seems backwards, but it is what the sk98lin
+ * does. Looks like hardware is wrong?
+ */
+ if (ipip_hdr(skb)->protocol == IPPROTO_UDP &&
+ hw->chip_rev == 0 && hw->chip_id == CHIP_ID_YUKON)
+ control = BMU_TCP_CHECK;
+ else
+ control = BMU_UDP_CHECK;
+
+ td->csum_offs = 0;
+ td->csum_start = offset;
+ td->csum_write = offset + skb->csum_offset;
+ } else
+ control = BMU_CHECK;
+
+ if (!skb_shinfo(skb)->nr_frags) /* single buffer i.e. no fragments */
+ control |= BMU_EOF | BMU_IRQ_EOF;
+ else {
+ struct skge_tx_desc *tf = td;
+
+ control |= BMU_STFWD;
+ for (i = 0; i < skb_shinfo(skb)->nr_frags; i++) {
+ const skb_frag_t *frag = &skb_shinfo(skb)->frags[i];
+
+ map = skb_frag_dma_map(&hw->pdev->dev, frag, 0,
+ skb_frag_size(frag), DMA_TO_DEVICE);
+ if (dma_mapping_error(&hw->pdev->dev, map))
+ goto mapping_unwind;
+
+ e = e->next;
+ e->skb = skb;
+ tf = e->desc;
+ BUG_ON(tf->control & BMU_OWN);
+
+ tf->dma_lo = lower_32_bits(map);
+ tf->dma_hi = upper_32_bits(map);
+ dma_unmap_addr_set(e, mapaddr, map);
+ dma_unmap_len_set(e, maplen, skb_frag_size(frag));
+
+ tf->control = BMU_OWN | BMU_SW | control | skb_frag_size(frag);
+ }
+ tf->control |= BMU_EOF | BMU_IRQ_EOF;
+ }
+ /* Make sure all the descriptors written */
+ wmb();
+ td->control = BMU_OWN | BMU_SW | BMU_STF | control | len;
+ wmb();
+
+ netdev_sent_queue(dev, skb->len);
+
+ skge_write8(hw, Q_ADDR(txqaddr[skge->port], Q_CSR), CSR_START);
+
+ netif_printk(skge, tx_queued, KERN_DEBUG, skge->netdev,
+ "tx queued, slot %td, len %d\n",
+ e - skge->tx_ring.start, skb->len);
+
+ skge->tx_ring.to_use = e->next;
+ smp_wmb();
+
+ if (skge_avail(&skge->tx_ring) <= TX_LOW_WATER) {
+ netdev_dbg(dev, "transmit queue full\n");
+ netif_stop_queue(dev);
+ }
+
+ return NETDEV_TX_OK;
+
+mapping_unwind:
+ e = skge->tx_ring.to_use;
+ pci_unmap_single(hw->pdev,
+ dma_unmap_addr(e, mapaddr),
+ dma_unmap_len(e, maplen),
+ PCI_DMA_TODEVICE);
+ while (i-- > 0) {
+ e = e->next;
+ pci_unmap_page(hw->pdev,
+ dma_unmap_addr(e, mapaddr),
+ dma_unmap_len(e, maplen),
+ PCI_DMA_TODEVICE);
+ }
+
+mapping_error:
+ if (net_ratelimit())
+ dev_warn(&hw->pdev->dev, "%s: tx mapping error\n", dev->name);
+ dev_kfree_skb_any(skb);
+ return NETDEV_TX_OK;
+}
+
+
+/* Free resources associated with this reing element */
+static inline void skge_tx_unmap(struct pci_dev *pdev, struct skge_element *e,
+ u32 control)
+{
+ /* skb header vs. fragment */
+ if (control & BMU_STF)
+ pci_unmap_single(pdev, dma_unmap_addr(e, mapaddr),
+ dma_unmap_len(e, maplen),
+ PCI_DMA_TODEVICE);
+ else
+ pci_unmap_page(pdev, dma_unmap_addr(e, mapaddr),
+ dma_unmap_len(e, maplen),
+ PCI_DMA_TODEVICE);
+}
+
+/* Free all buffers in transmit ring */
+static void skge_tx_clean(struct net_device *dev)
+{
+ struct skge_port *skge = netdev_priv(dev);
+ struct skge_element *e;
+
+ for (e = skge->tx_ring.to_clean; e != skge->tx_ring.to_use; e = e->next) {
+ struct skge_tx_desc *td = e->desc;
+
+ skge_tx_unmap(skge->hw->pdev, e, td->control);
+
+ if (td->control & BMU_EOF)
+ dev_kfree_skb(e->skb);
+ td->control = 0;
+ }
+
+ netdev_reset_queue(dev);
+ skge->tx_ring.to_clean = e;
+}
+
+static void skge_tx_timeout(struct net_device *dev)
+{
+ struct skge_port *skge = netdev_priv(dev);
+
+ netif_printk(skge, timer, KERN_DEBUG, skge->netdev, "tx timeout\n");
+
+ skge_write8(skge->hw, Q_ADDR(txqaddr[skge->port], Q_CSR), CSR_STOP);
+ skge_tx_clean(dev);
+ netif_wake_queue(dev);
+}
+
+static int skge_change_mtu(struct net_device *dev, int new_mtu)
+{
+ int err;
+
+ if (new_mtu < ETH_ZLEN || new_mtu > ETH_JUMBO_MTU)
+ return -EINVAL;
+
+ if (!netif_running(dev)) {
+ dev->mtu = new_mtu;
+ return 0;
+ }
+
+ skge_down(dev);
+
+ dev->mtu = new_mtu;
+
+ err = skge_up(dev);
+ if (err)
+ dev_close(dev);
+
+ return err;
+}
+
+static const u8 pause_mc_addr[ETH_ALEN] = { 0x1, 0x80, 0xc2, 0x0, 0x0, 0x1 };
+
+static void genesis_add_filter(u8 filter[8], const u8 *addr)
+{
+ u32 crc, bit;
+
+ crc = ether_crc_le(ETH_ALEN, addr);
+ bit = ~crc & 0x3f;
+ filter[bit/8] |= 1 << (bit%8);
+}
+
+static void genesis_set_multicast(struct net_device *dev)
+{
+ struct skge_port *skge = netdev_priv(dev);
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+ struct netdev_hw_addr *ha;
+ u32 mode;
+ u8 filter[8];
+
+ mode = xm_read32(hw, port, XM_MODE);
+ mode |= XM_MD_ENA_HASH;
+ if (dev->flags & IFF_PROMISC)
+ mode |= XM_MD_ENA_PROM;
+ else
+ mode &= ~XM_MD_ENA_PROM;
+
+ if (dev->flags & IFF_ALLMULTI)
+ memset(filter, 0xff, sizeof(filter));
+ else {
+ memset(filter, 0, sizeof(filter));
+
+ if (skge->flow_status == FLOW_STAT_REM_SEND ||
+ skge->flow_status == FLOW_STAT_SYMMETRIC)
+ genesis_add_filter(filter, pause_mc_addr);
+
+ netdev_for_each_mc_addr(ha, dev)
+ genesis_add_filter(filter, ha->addr);
+ }
+
+ xm_write32(hw, port, XM_MODE, mode);
+ xm_outhash(hw, port, XM_HSM, filter);
+}
+
+static void yukon_add_filter(u8 filter[8], const u8 *addr)
+{
+ u32 bit = ether_crc(ETH_ALEN, addr) & 0x3f;
+ filter[bit/8] |= 1 << (bit%8);
+}
+
+static void yukon_set_multicast(struct net_device *dev)
+{
+ struct skge_port *skge = netdev_priv(dev);
+ struct skge_hw *hw = skge->hw;
+ int port = skge->port;
+ struct netdev_hw_addr *ha;
+ int rx_pause = (skge->flow_status == FLOW_STAT_REM_SEND ||
+ skge->flow_status == FLOW_STAT_SYMMETRIC);
+ u16 reg;
+ u8 filter[8];
+
+ memset(filter, 0, sizeof(filter));
+
+ reg = gma_read16(hw, port, GM_RX_CTRL);
+ reg |= GM_RXCR_UCF_ENA;
+
+ if (dev->flags & IFF_PROMISC) /* promiscuous */
+ reg &= ~(GM_RXCR_UCF_ENA | GM_RXCR_MCF_ENA);
+ else if (dev->flags & IFF_ALLMULTI) /* all multicast */
+ memset(filter, 0xff, sizeof(filter));
+ else if (netdev_mc_empty(dev) && !rx_pause)/* no multicast */
+ reg &= ~GM_RXCR_MCF_ENA;
+ else {
+ reg |= GM_RXCR_MCF_ENA;
+
+ if (rx_pause)
+ yukon_add_filter(filter, pause_mc_addr);
+
+ netdev_for_each_mc_addr(ha, dev)
+ yukon_add_filter(filter, ha->addr);
+ }
+
+
+ gma_write16(hw, port, GM_MC_ADDR_H1,
+ (u16)filter[0] | ((u16)filter[1] << 8));
+ gma_write16(hw, port, GM_MC_ADDR_H2,
+ (u16)filter[2] | ((u16)filter[3] << 8));
+ gma_write16(hw, port, GM_MC_ADDR_H3,
+ (u16)filter[4] | ((u16)filter[5] << 8));
+ gma_write16(hw, port, GM_MC_ADDR_H4,
+ (u16)filter[6] | ((u16)filter[7] << 8));
+
+ gma_write16(hw, port, GM_RX_CTRL, reg);
+}
+
+static inline u16 phy_length(const struct skge_hw *hw, u32 status)
+{
+ if (is_genesis(hw))
+ return status >> XMR_FS_LEN_SHIFT;
+ else
+ return status >> GMR_FS_LEN_SHIFT;
+}
+
+static inline int bad_phy_status(const struct skge_hw *hw, u32 status)
+{
+ if (is_genesis(hw))
+ return (status & (XMR_FS_ERR | XMR_FS_2L_VLAN)) != 0;
+ else
+ return (status & GMR_FS_ANY_ERR) ||
+ (status & GMR_FS_RX_OK) == 0;
+}
+
+static void skge_set_multicast(struct net_device *dev)
+{
+ struct skge_port *skge = netdev_priv(dev);
+
+ if (is_genesis(skge->hw))
+ genesis_set_multicast(dev);
+ else
+ yukon_set_multicast(dev);
+
+}
+
+
+/* Get receive buffer from descriptor.
+ * Handles copy of small buffers and reallocation failures
+ */
+static struct sk_buff *skge_rx_get(struct net_device *dev,
+ struct skge_element *e,
+ u32 control, u32 status, u16 csum)
+{
+ struct skge_port *skge = netdev_priv(dev);
+ struct sk_buff *skb;
+ u16 len = control & BMU_BBC;
+
+ netif_printk(skge, rx_status, KERN_DEBUG, skge->netdev,
+ "rx slot %td status 0x%x len %d\n",
+ e - skge->rx_ring.start, status, len);
+
+ if (len > skge->rx_buf_size)
+ goto error;
+
+ if ((control & (BMU_EOF|BMU_STF)) != (BMU_STF|BMU_EOF))
+ goto error;
+
+ if (bad_phy_status(skge->hw, status))
+ goto error;
+
+ if (phy_length(skge->hw, status) != len)
+ goto error;
+
+ if (len < RX_COPY_THRESHOLD) {
+ skb = netdev_alloc_skb_ip_align(dev, len);
+ if (!skb)
+ goto resubmit;
+
+ pci_dma_sync_single_for_cpu(skge->hw->pdev,
+ dma_unmap_addr(e, mapaddr),
+ dma_unmap_len(e, maplen),
+ PCI_DMA_FROMDEVICE);
+ skb_copy_from_linear_data(e->skb, skb->data, len);
+ pci_dma_sync_single_for_device(skge->hw->pdev,
+ dma_unmap_addr(e, mapaddr),
+ dma_unmap_len(e, maplen),
+ PCI_DMA_FROMDEVICE);
+ skge_rx_reuse(e, skge->rx_buf_size);
+ } else {
+ struct skge_element ee;
+ struct sk_buff *nskb;
+
+ nskb = netdev_alloc_skb_ip_align(dev, skge->rx_buf_size);
+ if (!nskb)
+ goto resubmit;
+
+ ee = *e;
+
+ skb = ee.skb;
+ prefetch(skb->data);
+
+ if (skge_rx_setup(skge, e, nskb, skge->rx_buf_size) < 0) {
+ dev_kfree_skb(nskb);
+ goto resubmit;
+ }
+
+ pci_unmap_single(skge->hw->pdev,
+ dma_unmap_addr(&ee, mapaddr),
+ dma_unmap_len(&ee, maplen),
+ PCI_DMA_FROMDEVICE);
+ }
+
+ skb_put(skb, len);
+
+ if (dev->features & NETIF_F_RXCSUM) {
+ skb->csum = csum;
+ skb->ip_summed = CHECKSUM_COMPLETE;
+ }
+
+ skb->protocol = eth_type_trans(skb, dev);
+
+ return skb;
+error:
+
+ netif_printk(skge, rx_err, KERN_DEBUG, skge->netdev,
+ "rx err, slot %td control 0x%x status 0x%x\n",
+ e - skge->rx_ring.start, control, status);
+
+ if (is_genesis(skge->hw)) {
+ if (status & (XMR_FS_RUNT|XMR_FS_LNG_ERR))
+ dev->stats.rx_length_errors++;
+ if (status & XMR_FS_FRA_ERR)
+ dev->stats.rx_frame_errors++;
+ if (status & XMR_FS_FCS_ERR)
+ dev->stats.rx_crc_errors++;
+ } else {
+ if (status & (GMR_FS_LONG_ERR|GMR_FS_UN_SIZE))
+ dev->stats.rx_length_errors++;
+ if (status & GMR_FS_FRAGMENT)
+ dev->stats.rx_frame_errors++;
+ if (status & GMR_FS_CRC_ERR)
+ dev->stats.rx_crc_errors++;
+ }
+
+resubmit:
+ skge_rx_reuse(e, skge->rx_buf_size);
+ return NULL;
+}
+
+/* Free all buffers in Tx ring which are no longer owned by device */
+static void skge_tx_done(struct net_device *dev)
+{
+ struct skge_port *skge = netdev_priv(dev);
+ struct skge_ring *ring = &skge->tx_ring;
+ struct skge_element *e;
+ unsigned int bytes_compl = 0, pkts_compl = 0;
+
+ skge_write8(skge->hw, Q_ADDR(txqaddr[skge->port], Q_CSR), CSR_IRQ_CL_F);
+
+ for (e = ring->to_clean; e != ring->to_use; e = e->next) {
+ u32 control = ((const struct skge_tx_desc *) e->desc)->control;
+
+ if (control & BMU_OWN)
+ break;
+
+ skge_tx_unmap(skge->hw->pdev, e, control);
+
+ if (control & BMU_EOF) {
+ netif_printk(skge, tx_done, KERN_DEBUG, skge->netdev,
+ "tx done slot %td\n",
+ e - skge->tx_ring.start);
+
+ pkts_compl++;
+ bytes_compl += e->skb->len;
+
+ dev_consume_skb_any(e->skb);
+ }
+ }
+ netdev_completed_queue(dev, pkts_compl, bytes_compl);
+ skge->tx_ring.to_clean = e;
+
+ /* Can run lockless until we need to synchronize to restart queue. */
+ smp_mb();
+
+ if (unlikely(netif_queue_stopped(dev) &&
+ skge_avail(&skge->tx_ring) > TX_LOW_WATER)) {
+ netif_tx_lock(dev);
+ if (unlikely(netif_queue_stopped(dev) &&
+ skge_avail(&skge->tx_ring) > TX_LOW_WATER)) {
+ netif_wake_queue(dev);
+
+ }
+ netif_tx_unlock(dev);
+ }
+}
+
+static int skge_poll(struct napi_struct *napi, int to_do)
+{
+ struct skge_port *skge = container_of(napi, struct skge_port, napi);
+ struct net_device *dev = skge->netdev;
+ struct skge_hw *hw = skge->hw;
+ struct skge_ring *ring = &skge->rx_ring;
+ struct skge_element *e;
+ int work_done = 0;
+
+ skge_tx_done(dev);
+
+ skge_write8(hw, Q_ADDR(rxqaddr[skge->port], Q_CSR), CSR_IRQ_CL_F);
+
+ for (e = ring->to_clean; prefetch(e->next), work_done < to_do; e = e->next) {
+ struct skge_rx_desc *rd = e->desc;
+ struct sk_buff *skb;
+ u32 control;
+
+ rmb();
+ control = rd->control;
+ if (control & BMU_OWN)
+ break;
+
+ skb = skge_rx_get(dev, e, control, rd->status, rd->csum2);
+ if (likely(skb)) {
+ napi_gro_receive(napi, skb);
+ ++work_done;
+ }
+ }
+ ring->to_clean = e;
+
+ /* restart receiver */
+ wmb();
+ skge_write8(hw, Q_ADDR(rxqaddr[skge->port], Q_CSR), CSR_START);
+
+ if (work_done < to_do) {
+ unsigned long flags;
+
+ napi_gro_flush(napi, false);
+ spin_lock_irqsave(&hw->hw_lock, flags);
+ __napi_complete(napi);
+ hw->intr_mask |= napimask[skge->port];
+ skge_write32(hw, B0_IMSK, hw->intr_mask);
+ skge_read32(hw, B0_IMSK);
+ spin_unlock_irqrestore(&hw->hw_lock, flags);
+ }
+
+ return work_done;
+}
+
+/* Parity errors seem to happen when Genesis is connected to a switch
+ * with no other ports present. Heartbeat error??
+ */
+static void skge_mac_parity(struct skge_hw *hw, int port)
+{
+ struct net_device *dev = hw->dev[port];
+
+ ++dev->stats.tx_heartbeat_errors;
+
+ if (is_genesis(hw))
+ skge_write16(hw, SK_REG(port, TX_MFF_CTRL1),
+ MFF_CLR_PERR);
+ else
+ /* HW-Bug #8: cleared by GMF_CLI_TX_FC instead of GMF_CLI_TX_PE */
+ skge_write8(hw, SK_REG(port, TX_GMF_CTRL_T),
+ (hw->chip_id == CHIP_ID_YUKON && hw->chip_rev == 0)
+ ? GMF_CLI_TX_FC : GMF_CLI_TX_PE);
+}
+
+static void skge_mac_intr(struct skge_hw *hw, int port)
+{
+ if (is_genesis(hw))
+ genesis_mac_intr(hw, port);
+ else
+ yukon_mac_intr(hw, port);
+}
+
+/* Handle device specific framing and timeout interrupts */
+static void skge_error_irq(struct skge_hw *hw)
+{
+ struct pci_dev *pdev = hw->pdev;
+ u32 hwstatus = skge_read32(hw, B0_HWE_ISRC);
+
+ if (is_genesis(hw)) {
+ /* clear xmac errors */
+ if (hwstatus & (IS_NO_STAT_M1|IS_NO_TIST_M1))
+ skge_write16(hw, RX_MFF_CTRL1, MFF_CLR_INSTAT);
+ if (hwstatus & (IS_NO_STAT_M2|IS_NO_TIST_M2))
+ skge_write16(hw, RX_MFF_CTRL2, MFF_CLR_INSTAT);
+ } else {
+ /* Timestamp (unused) overflow */
+ if (hwstatus & IS_IRQ_TIST_OV)
+ skge_write8(hw, GMAC_TI_ST_CTRL, GMT_ST_CLR_IRQ);
+ }
+
+ if (hwstatus & IS_RAM_RD_PAR) {
+ dev_err(&pdev->dev, "Ram read data parity error\n");
+ skge_write16(hw, B3_RI_CTRL, RI_CLR_RD_PERR);
+ }
+
+ if (hwstatus & IS_RAM_WR_PAR) {
+ dev_err(&pdev->dev, "Ram write data parity error\n");
+ skge_write16(hw, B3_RI_CTRL, RI_CLR_WR_PERR);
+ }
+
+ if (hwstatus & IS_M1_PAR_ERR)
+ skge_mac_parity(hw, 0);
+
+ if (hwstatus & IS_M2_PAR_ERR)
+ skge_mac_parity(hw, 1);
+
+ if (hwstatus & IS_R1_PAR_ERR) {
+ dev_err(&pdev->dev, "%s: receive queue parity error\n",
+ hw->dev[0]->name);
+ skge_write32(hw, B0_R1_CSR, CSR_IRQ_CL_P);
+ }
+
+ if (hwstatus & IS_R2_PAR_ERR) {
+ dev_err(&pdev->dev, "%s: receive queue parity error\n",
+ hw->dev[1]->name);
+ skge_write32(hw, B0_R2_CSR, CSR_IRQ_CL_P);
+ }
+
+ if (hwstatus & (IS_IRQ_MST_ERR|IS_IRQ_STAT)) {
+ u16 pci_status, pci_cmd;
+
+ pci_read_config_word(pdev, PCI_COMMAND, &pci_cmd);
+ pci_read_config_word(pdev, PCI_STATUS, &pci_status);
+
+ dev_err(&pdev->dev, "PCI error cmd=%#x status=%#x\n",
+ pci_cmd, pci_status);
+
+ /* Write the error bits back to clear them. */
+ pci_status &= PCI_STATUS_ERROR_BITS;
+ skge_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
+ pci_write_config_word(pdev, PCI_COMMAND,
+ pci_cmd | PCI_COMMAND_SERR | PCI_COMMAND_PARITY);
+ pci_write_config_word(pdev, PCI_STATUS, pci_status);
+ skge_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
+
+ /* if error still set then just ignore it */
+ hwstatus = skge_read32(hw, B0_HWE_ISRC);
+ if (hwstatus & IS_IRQ_STAT) {
+ dev_warn(&hw->pdev->dev, "unable to clear error (so ignoring them)\n");
+ hw->intr_mask &= ~IS_HW_ERR;
+ }
+ }
+}
+
+/*
+ * Interrupt from PHY are handled in tasklet (softirq)
+ * because accessing phy registers requires spin wait which might
+ * cause excess interrupt latency.
+ */
+static void skge_extirq(unsigned long arg)
+{
+ struct skge_hw *hw = (struct skge_hw *) arg;
+ int port;
+
+ for (port = 0; port < hw->ports; port++) {
+ struct net_device *dev = hw->dev[port];
+
+ if (netif_running(dev)) {
+ struct skge_port *skge = netdev_priv(dev);
+
+ spin_lock(&hw->phy_lock);
+ if (!is_genesis(hw))
+ yukon_phy_intr(skge);
+ else if (hw->phy_type == SK_PHY_BCOM)
+ bcom_phy_intr(skge);
+ spin_unlock(&hw->phy_lock);
+ }
+ }
+
+ spin_lock_irq(&hw->hw_lock);
+ hw->intr_mask |= IS_EXT_REG;
+ skge_write32(hw, B0_IMSK, hw->intr_mask);
+ skge_read32(hw, B0_IMSK);
+ spin_unlock_irq(&hw->hw_lock);
+}
+
+static irqreturn_t skge_intr(int irq, void *dev_id)
+{
+ struct skge_hw *hw = dev_id;
+ u32 status;
+ int handled = 0;
+
+ spin_lock(&hw->hw_lock);
+ /* Reading this register masks IRQ */
+ status = skge_read32(hw, B0_SP_ISRC);
+ if (status == 0 || status == ~0)
+ goto out;
+
+ handled = 1;
+ status &= hw->intr_mask;
+ if (status & IS_EXT_REG) {
+ hw->intr_mask &= ~IS_EXT_REG;
+ tasklet_schedule(&hw->phy_task);
+ }
+
+ if (status & (IS_XA1_F|IS_R1_F)) {
+ struct skge_port *skge = netdev_priv(hw->dev[0]);
+ hw->intr_mask &= ~(IS_XA1_F|IS_R1_F);
+ napi_schedule(&skge->napi);
+ }
+
+ if (status & IS_PA_TO_TX1)
+ skge_write16(hw, B3_PA_CTRL, PA_CLR_TO_TX1);
+
+ if (status & IS_PA_TO_RX1) {
+ ++hw->dev[0]->stats.rx_over_errors;
+ skge_write16(hw, B3_PA_CTRL, PA_CLR_TO_RX1);
+ }
+
+
+ if (status & IS_MAC1)
+ skge_mac_intr(hw, 0);
+
+ if (hw->dev[1]) {
+ struct skge_port *skge = netdev_priv(hw->dev[1]);
+
+ if (status & (IS_XA2_F|IS_R2_F)) {
+ hw->intr_mask &= ~(IS_XA2_F|IS_R2_F);
+ napi_schedule(&skge->napi);
+ }
+
+ if (status & IS_PA_TO_RX2) {
+ ++hw->dev[1]->stats.rx_over_errors;
+ skge_write16(hw, B3_PA_CTRL, PA_CLR_TO_RX2);
+ }
+
+ if (status & IS_PA_TO_TX2)
+ skge_write16(hw, B3_PA_CTRL, PA_CLR_TO_TX2);
+
+ if (status & IS_MAC2)
+ skge_mac_intr(hw, 1);
+ }
+
+ if (status & IS_HW_ERR)
+ skge_error_irq(hw);
+out:
+ skge_write32(hw, B0_IMSK, hw->intr_mask);
+ skge_read32(hw, B0_IMSK);
+ spin_unlock(&hw->hw_lock);
+
+ return IRQ_RETVAL(handled);
+}
+
+#ifdef CONFIG_NET_POLL_CONTROLLER
+static void skge_netpoll(struct net_device *dev)
+{
+ struct skge_port *skge = netdev_priv(dev);
+
+ disable_irq(dev->irq);
+ skge_intr(dev->irq, skge->hw);
+ enable_irq(dev->irq);
+}
+#endif
+
+static int skge_set_mac_address(struct net_device *dev, void *p)
+{
+ struct skge_port *skge = netdev_priv(dev);
+ struct skge_hw *hw = skge->hw;
+ unsigned port = skge->port;
+ const struct sockaddr *addr = p;
+ u16 ctrl;
+
+ if (!is_valid_ether_addr(addr->sa_data))
+ return -EADDRNOTAVAIL;
+
+ memcpy(dev->dev_addr, addr->sa_data, ETH_ALEN);
+
+ if (!netif_running(dev)) {
+ memcpy_toio(hw->regs + B2_MAC_1 + port*8, dev->dev_addr, ETH_ALEN);
+ memcpy_toio(hw->regs + B2_MAC_2 + port*8, dev->dev_addr, ETH_ALEN);
+ } else {
+ /* disable Rx */
+ spin_lock_bh(&hw->phy_lock);
+ ctrl = gma_read16(hw, port, GM_GP_CTRL);
+ gma_write16(hw, port, GM_GP_CTRL, ctrl & ~GM_GPCR_RX_ENA);
+
+ memcpy_toio(hw->regs + B2_MAC_1 + port*8, dev->dev_addr, ETH_ALEN);
+ memcpy_toio(hw->regs + B2_MAC_2 + port*8, dev->dev_addr, ETH_ALEN);
+
+ if (is_genesis(hw))
+ xm_outaddr(hw, port, XM_SA, dev->dev_addr);
+ else {
+ gma_set_addr(hw, port, GM_SRC_ADDR_1L, dev->dev_addr);
+ gma_set_addr(hw, port, GM_SRC_ADDR_2L, dev->dev_addr);
+ }
+
+ gma_write16(hw, port, GM_GP_CTRL, ctrl);
+ spin_unlock_bh(&hw->phy_lock);
+ }
+
+ return 0;
+}
+
+static const struct {
+ u8 id;
+ const char *name;
+} skge_chips[] = {
+ { CHIP_ID_GENESIS, "Genesis" },
+ { CHIP_ID_YUKON, "Yukon" },
+ { CHIP_ID_YUKON_LITE, "Yukon-Lite"},
+ { CHIP_ID_YUKON_LP, "Yukon-LP"},
+};
+
+static const char *skge_board_name(const struct skge_hw *hw)
+{
+ int i;
+ static char buf[16];
+
+ for (i = 0; i < ARRAY_SIZE(skge_chips); i++)
+ if (skge_chips[i].id == hw->chip_id)
+ return skge_chips[i].name;
+
+ snprintf(buf, sizeof buf, "chipid 0x%x", hw->chip_id);
+ return buf;
+}
+
+
+/*
+ * Setup the board data structure, but don't bring up
+ * the port(s)
+ */
+static int skge_reset(struct skge_hw *hw)
+{
+ u32 reg;
+ u16 ctst, pci_status;
+ u8 t8, mac_cfg, pmd_type;
+ int i;
+
+ ctst = skge_read16(hw, B0_CTST);
+
+ /* do a SW reset */
+ skge_write8(hw, B0_CTST, CS_RST_SET);
+ skge_write8(hw, B0_CTST, CS_RST_CLR);
+
+ /* clear PCI errors, if any */
+ skge_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
+ skge_write8(hw, B2_TST_CTRL2, 0);
+
+ pci_read_config_word(hw->pdev, PCI_STATUS, &pci_status);
+ pci_write_config_word(hw->pdev, PCI_STATUS,
+ pci_status | PCI_STATUS_ERROR_BITS);
+ skge_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
+ skge_write8(hw, B0_CTST, CS_MRST_CLR);
+
+ /* restore CLK_RUN bits (for Yukon-Lite) */
+ skge_write16(hw, B0_CTST,
+ ctst & (CS_CLK_RUN_HOT|CS_CLK_RUN_RST|CS_CLK_RUN_ENA));
+
+ hw->chip_id = skge_read8(hw, B2_CHIP_ID);
+ hw->phy_type = skge_read8(hw, B2_E_1) & 0xf;
+ pmd_type = skge_read8(hw, B2_PMD_TYP);
+ hw->copper = (pmd_type == 'T' || pmd_type == '1');
+
+ switch (hw->chip_id) {
+ case CHIP_ID_GENESIS:
+#ifdef CONFIG_SKGE_GENESIS
+ switch (hw->phy_type) {
+ case SK_PHY_XMAC:
+ hw->phy_addr = PHY_ADDR_XMAC;
+ break;
+ case SK_PHY_BCOM:
+ hw->phy_addr = PHY_ADDR_BCOM;
+ break;
+ default:
+ dev_err(&hw->pdev->dev, "unsupported phy type 0x%x\n",
+ hw->phy_type);
+ return -EOPNOTSUPP;
+ }
+ break;
+#else
+ dev_err(&hw->pdev->dev, "Genesis chip detected but not configured\n");
+ return -EOPNOTSUPP;
+#endif
+
+ case CHIP_ID_YUKON:
+ case CHIP_ID_YUKON_LITE:
+ case CHIP_ID_YUKON_LP:
+ if (hw->phy_type < SK_PHY_MARV_COPPER && pmd_type != 'S')
+ hw->copper = 1;
+
+ hw->phy_addr = PHY_ADDR_MARV;
+ break;
+
+ default:
+ dev_err(&hw->pdev->dev, "unsupported chip type 0x%x\n",
+ hw->chip_id);
+ return -EOPNOTSUPP;
+ }
+
+ mac_cfg = skge_read8(hw, B2_MAC_CFG);
+ hw->ports = (mac_cfg & CFG_SNG_MAC) ? 1 : 2;
+ hw->chip_rev = (mac_cfg & CFG_CHIP_R_MSK) >> 4;
+
+ /* read the adapters RAM size */
+ t8 = skge_read8(hw, B2_E_0);
+ if (is_genesis(hw)) {
+ if (t8 == 3) {
+ /* special case: 4 x 64k x 36, offset = 0x80000 */
+ hw->ram_size = 0x100000;
+ hw->ram_offset = 0x80000;
+ } else
+ hw->ram_size = t8 * 512;
+ } else if (t8 == 0)
+ hw->ram_size = 0x20000;
+ else
+ hw->ram_size = t8 * 4096;
+
+ hw->intr_mask = IS_HW_ERR;
+
+ /* Use PHY IRQ for all but fiber based Genesis board */
+ if (!(is_genesis(hw) && hw->phy_type == SK_PHY_XMAC))
+ hw->intr_mask |= IS_EXT_REG;
+
+ if (is_genesis(hw))
+ genesis_init(hw);
+ else {
+ /* switch power to VCC (WA for VAUX problem) */
+ skge_write8(hw, B0_POWER_CTRL,
+ PC_VAUX_ENA | PC_VCC_ENA | PC_VAUX_OFF | PC_VCC_ON);
+
+ /* avoid boards with stuck Hardware error bits */
+ if ((skge_read32(hw, B0_ISRC) & IS_HW_ERR) &&
+ (skge_read32(hw, B0_HWE_ISRC) & IS_IRQ_SENSOR)) {
+ dev_warn(&hw->pdev->dev, "stuck hardware sensor bit\n");
+ hw->intr_mask &= ~IS_HW_ERR;
+ }
+
+ /* Clear PHY COMA */
+ skge_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
+ pci_read_config_dword(hw->pdev, PCI_DEV_REG1, ®);
+ reg &= ~PCI_PHY_COMA;
+ pci_write_config_dword(hw->pdev, PCI_DEV_REG1, reg);
+ skge_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
+
+
+ for (i = 0; i < hw->ports; i++) {
+ skge_write16(hw, SK_REG(i, GMAC_LINK_CTRL), GMLC_RST_SET);
+ skge_write16(hw, SK_REG(i, GMAC_LINK_CTRL), GMLC_RST_CLR);
+ }
+ }
+
+ /* turn off hardware timer (unused) */
+ skge_write8(hw, B2_TI_CTRL, TIM_STOP);
+ skge_write8(hw, B2_TI_CTRL, TIM_CLR_IRQ);
+ skge_write8(hw, B0_LED, LED_STAT_ON);
+
+ /* enable the Tx Arbiters */
+ for (i = 0; i < hw->ports; i++)
+ skge_write8(hw, SK_REG(i, TXA_CTRL), TXA_ENA_ARB);
+
+ /* Initialize ram interface */
+ skge_write16(hw, B3_RI_CTRL, RI_RST_CLR);
+
+ skge_write8(hw, B3_RI_WTO_R1, SK_RI_TO_53);
+ skge_write8(hw, B3_RI_WTO_XA1, SK_RI_TO_53);
+ skge_write8(hw, B3_RI_WTO_XS1, SK_RI_TO_53);
+ skge_write8(hw, B3_RI_RTO_R1, SK_RI_TO_53);
+ skge_write8(hw, B3_RI_RTO_XA1, SK_RI_TO_53);
+ skge_write8(hw, B3_RI_RTO_XS1, SK_RI_TO_53);
+ skge_write8(hw, B3_RI_WTO_R2, SK_RI_TO_53);
+ skge_write8(hw, B3_RI_WTO_XA2, SK_RI_TO_53);
+ skge_write8(hw, B3_RI_WTO_XS2, SK_RI_TO_53);
+ skge_write8(hw, B3_RI_RTO_R2, SK_RI_TO_53);
+ skge_write8(hw, B3_RI_RTO_XA2, SK_RI_TO_53);
+ skge_write8(hw, B3_RI_RTO_XS2, SK_RI_TO_53);
+
+ skge_write32(hw, B0_HWE_IMSK, IS_ERR_MSK);
+
+ /* Set interrupt moderation for Transmit only
+ * Receive interrupts avoided by NAPI
+ */
+ skge_write32(hw, B2_IRQM_MSK, IS_XA1_F|IS_XA2_F);
+ skge_write32(hw, B2_IRQM_INI, skge_usecs2clk(hw, 100));
+ skge_write32(hw, B2_IRQM_CTRL, TIM_START);
+
+ /* Leave irq disabled until first port is brought up. */
+ skge_write32(hw, B0_IMSK, 0);
+
+ for (i = 0; i < hw->ports; i++) {
+ if (is_genesis(hw))
+ genesis_reset(hw, i);
+ else
+ yukon_reset(hw, i);
+ }
+
+ return 0;
+}
+
+
+#ifdef CONFIG_SKGE_DEBUG
+
+static struct dentry *skge_debug;
+
+static int skge_debug_show(struct seq_file *seq, void *v)
+{
+ struct net_device *dev = seq->private;
+ const struct skge_port *skge = netdev_priv(dev);
+ const struct skge_hw *hw = skge->hw;
+ const struct skge_element *e;
+
+ if (!netif_running(dev))
+ return -ENETDOWN;
+
+ seq_printf(seq, "IRQ src=%x mask=%x\n", skge_read32(hw, B0_ISRC),
+ skge_read32(hw, B0_IMSK));
+
+ seq_printf(seq, "Tx Ring: (%d)\n", skge_avail(&skge->tx_ring));
+ for (e = skge->tx_ring.to_clean; e != skge->tx_ring.to_use; e = e->next) {
+ const struct skge_tx_desc *t = e->desc;
+ seq_printf(seq, "%#x dma=%#x%08x %#x csum=%#x/%x/%x\n",
+ t->control, t->dma_hi, t->dma_lo, t->status,
+ t->csum_offs, t->csum_write, t->csum_start);
+ }
+
+ seq_printf(seq, "\nRx Ring:\n");
+ for (e = skge->rx_ring.to_clean; ; e = e->next) {
+ const struct skge_rx_desc *r = e->desc;
+
+ if (r->control & BMU_OWN)
+ break;
+
+ seq_printf(seq, "%#x dma=%#x%08x %#x %#x csum=%#x/%x\n",
+ r->control, r->dma_hi, r->dma_lo, r->status,
+ r->timestamp, r->csum1, r->csum1_start);
+ }
+
+ return 0;
+}
+
+static int skge_debug_open(struct inode *inode, struct file *file)
+{
+ return single_open(file, skge_debug_show, inode->i_private);
+}
+
+static const struct file_operations skge_debug_fops = {
+ .owner = THIS_MODULE,
+ .open = skge_debug_open,
+ .read = seq_read,
+ .llseek = seq_lseek,
+ .release = single_release,
+};
+
+/*
+ * Use network device events to create/remove/rename
+ * debugfs file entries
+ */
+static int skge_device_event(struct notifier_block *unused,
+ unsigned long event, void *ptr)
+{
+ struct net_device *dev = netdev_notifier_info_to_dev(ptr);
+ struct skge_port *skge;
+ struct dentry *d;
+
+ if (dev->netdev_ops->ndo_open != &skge_up || !skge_debug)
+ goto done;
+
+ skge = netdev_priv(dev);
+ switch (event) {
+ case NETDEV_CHANGENAME:
+ if (skge->debugfs) {
+ d = debugfs_rename(skge_debug, skge->debugfs,
+ skge_debug, dev->name);
+ if (d)
+ skge->debugfs = d;
+ else {
+ netdev_info(dev, "rename failed\n");
+ debugfs_remove(skge->debugfs);
+ }
+ }
+ break;
+
+ case NETDEV_GOING_DOWN:
+ if (skge->debugfs) {
+ debugfs_remove(skge->debugfs);
+ skge->debugfs = NULL;
+ }
+ break;
+
+ case NETDEV_UP:
+ d = debugfs_create_file(dev->name, S_IRUGO,
+ skge_debug, dev,
+ &skge_debug_fops);
+ if (!d || IS_ERR(d))
+ netdev_info(dev, "debugfs create failed\n");
+ else
+ skge->debugfs = d;
+ break;
+ }
+
+done:
+ return NOTIFY_DONE;
+}
+
+static struct notifier_block skge_notifier = {
+ .notifier_call = skge_device_event,
+};
+
+
+static __init void skge_debug_init(void)
+{
+ struct dentry *ent;
+
+ ent = debugfs_create_dir("skge", NULL);
+ if (!ent || IS_ERR(ent)) {
+ pr_info("debugfs create directory failed\n");
+ return;
+ }
+
+ skge_debug = ent;
+ register_netdevice_notifier(&skge_notifier);
+}
+
+static __exit void skge_debug_cleanup(void)
+{
+ if (skge_debug) {
+ unregister_netdevice_notifier(&skge_notifier);
+ debugfs_remove(skge_debug);
+ skge_debug = NULL;
+ }
+}
+
+#else
+#define skge_debug_init()
+#define skge_debug_cleanup()
+#endif
+
+static const struct net_device_ops skge_netdev_ops = {
+ .ndo_open = skge_up,
+ .ndo_stop = skge_down,
+ .ndo_start_xmit = skge_xmit_frame,
+ .ndo_do_ioctl = skge_ioctl,
+ .ndo_get_stats = skge_get_stats,
+ .ndo_tx_timeout = skge_tx_timeout,
+ .ndo_change_mtu = skge_change_mtu,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_set_rx_mode = skge_set_multicast,
+ .ndo_set_mac_address = skge_set_mac_address,
+#ifdef CONFIG_NET_POLL_CONTROLLER
+ .ndo_poll_controller = skge_netpoll,
+#endif
+};
+
+
+/* Initialize network device */
+static struct net_device *skge_devinit(struct skge_hw *hw, int port,
+ int highmem)
+{
+ struct skge_port *skge;
+ struct net_device *dev = alloc_etherdev(sizeof(*skge));
+
+ if (!dev)
+ return NULL;
+
+ SET_NETDEV_DEV(dev, &hw->pdev->dev);
+ dev->netdev_ops = &skge_netdev_ops;
+ dev->ethtool_ops = &skge_ethtool_ops;
+ dev->watchdog_timeo = TX_WATCHDOG;
+ dev->irq = hw->pdev->irq;
+
+ if (highmem)
+ dev->features |= NETIF_F_HIGHDMA;
+
+ skge = netdev_priv(dev);
+ netif_napi_add(dev, &skge->napi, skge_poll, NAPI_WEIGHT);
+ skge->netdev = dev;
+ skge->hw = hw;
+ skge->msg_enable = netif_msg_init(debug, default_msg);
+
+ skge->tx_ring.count = DEFAULT_TX_RING_SIZE;
+ skge->rx_ring.count = DEFAULT_RX_RING_SIZE;
+
+ /* Auto speed and flow control */
+ skge->autoneg = AUTONEG_ENABLE;
+ skge->flow_control = FLOW_MODE_SYM_OR_REM;
+ skge->duplex = -1;
+ skge->speed = -1;
+ skge->advertising = skge_supported_modes(hw);
+
+ if (device_can_wakeup(&hw->pdev->dev)) {
+ skge->wol = wol_supported(hw) & WAKE_MAGIC;
+ device_set_wakeup_enable(&hw->pdev->dev, skge->wol);
+ }
+
+ hw->dev[port] = dev;
+
+ skge->port = port;
+
+ /* Only used for Genesis XMAC */
+ if (is_genesis(hw))
+ setup_timer(&skge->link_timer, xm_link_timer, (unsigned long) skge);
+ else {
+ dev->hw_features = NETIF_F_IP_CSUM | NETIF_F_SG |
+ NETIF_F_RXCSUM;
+ dev->features |= dev->hw_features;
+ }
+
+ /* read the mac address */
+ memcpy_fromio(dev->dev_addr, hw->regs + B2_MAC_1 + port*8, ETH_ALEN);
+
+ return dev;
+}
+
+static void skge_show_addr(struct net_device *dev)
+{
+ const struct skge_port *skge = netdev_priv(dev);
+
+ netif_info(skge, probe, skge->netdev, "addr %pM\n", dev->dev_addr);
+}
+
+static int only_32bit_dma;
+
+static int skge_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
+{
+ struct net_device *dev, *dev1;
+ struct skge_hw *hw;
+ int err, using_dac = 0;
+
+ err = pci_enable_device(pdev);
+ if (err) {
+ dev_err(&pdev->dev, "cannot enable PCI device\n");
+ goto err_out;
+ }
+
+ err = pci_request_regions(pdev, DRV_NAME);
+ if (err) {
+ dev_err(&pdev->dev, "cannot obtain PCI resources\n");
+ goto err_out_disable_pdev;
+ }
+
+ pci_set_master(pdev);
+
+ if (!only_32bit_dma && !pci_set_dma_mask(pdev, DMA_BIT_MASK(64))) {
+ using_dac = 1;
+ err = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(64));
+ } else if (!(err = pci_set_dma_mask(pdev, DMA_BIT_MASK(32)))) {
+ using_dac = 0;
+ err = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32));
+ }
+
+ if (err) {
+ dev_err(&pdev->dev, "no usable DMA configuration\n");
+ goto err_out_free_regions;
+ }
+
+#ifdef __BIG_ENDIAN
+ /* byte swap descriptors in hardware */
+ {
+ u32 reg;
+
+ pci_read_config_dword(pdev, PCI_DEV_REG2, ®);
+ reg |= PCI_REV_DESC;
+ pci_write_config_dword(pdev, PCI_DEV_REG2, reg);
+ }
+#endif
+
+ err = -ENOMEM;
+ /* space for skge@pci:0000:04:00.0 */
+ hw = kzalloc(sizeof(*hw) + strlen(DRV_NAME "@pci:")
+ + strlen(pci_name(pdev)) + 1, GFP_KERNEL);
+ if (!hw)
+ goto err_out_free_regions;
+
+ sprintf(hw->irq_name, DRV_NAME "@pci:%s", pci_name(pdev));
+
+ hw->pdev = pdev;
+ spin_lock_init(&hw->hw_lock);
+ spin_lock_init(&hw->phy_lock);
+ tasklet_init(&hw->phy_task, skge_extirq, (unsigned long) hw);
+
+ hw->regs = ioremap_nocache(pci_resource_start(pdev, 0), 0x4000);
+ if (!hw->regs) {
+ dev_err(&pdev->dev, "cannot map device registers\n");
+ goto err_out_free_hw;
+ }
+
+ err = skge_reset(hw);
+ if (err)
+ goto err_out_iounmap;
+
+ pr_info("%s addr 0x%llx irq %d chip %s rev %d\n",
+ DRV_VERSION,
+ (unsigned long long)pci_resource_start(pdev, 0), pdev->irq,
+ skge_board_name(hw), hw->chip_rev);
+
+ dev = skge_devinit(hw, 0, using_dac);
+ if (!dev) {
+ err = -ENOMEM;
+ goto err_out_led_off;
+ }
+
+ /* Some motherboards are broken and has zero in ROM. */
+ if (!is_valid_ether_addr(dev->dev_addr))
+ dev_warn(&pdev->dev, "bad (zero?) ethernet address in rom\n");
+
+ err = register_netdev(dev);
+ if (err) {
+ dev_err(&pdev->dev, "cannot register net device\n");
+ goto err_out_free_netdev;
+ }
+
+ skge_show_addr(dev);
+
+ if (hw->ports > 1) {
+ dev1 = skge_devinit(hw, 1, using_dac);
+ if (!dev1) {
+ err = -ENOMEM;
+ goto err_out_unregister;
+ }
+
+ err = register_netdev(dev1);
+ if (err) {
+ dev_err(&pdev->dev, "cannot register second net device\n");
+ goto err_out_free_dev1;
+ }
+
+ err = request_irq(pdev->irq, skge_intr, IRQF_SHARED,
+ hw->irq_name, hw);
+ if (err) {
+ dev_err(&pdev->dev, "cannot assign irq %d\n",
+ pdev->irq);
+ goto err_out_unregister_dev1;
+ }
+
+ skge_show_addr(dev1);
+ }
+ pci_set_drvdata(pdev, hw);
+
+ return 0;
+
+err_out_unregister_dev1:
+ unregister_netdev(dev1);
+err_out_free_dev1:
+ free_netdev(dev1);
+err_out_unregister:
+ unregister_netdev(dev);
+err_out_free_netdev:
+ free_netdev(dev);
+err_out_led_off:
+ skge_write16(hw, B0_LED, LED_STAT_OFF);
+err_out_iounmap:
+ iounmap(hw->regs);
+err_out_free_hw:
+ kfree(hw);
+err_out_free_regions:
+ pci_release_regions(pdev);
+err_out_disable_pdev:
+ pci_disable_device(pdev);
+err_out:
+ return err;
+}
+
+static void skge_remove(struct pci_dev *pdev)
+{
+ struct skge_hw *hw = pci_get_drvdata(pdev);
+ struct net_device *dev0, *dev1;
+
+ if (!hw)
+ return;
+
+ dev1 = hw->dev[1];
+ if (dev1)
+ unregister_netdev(dev1);
+ dev0 = hw->dev[0];
+ unregister_netdev(dev0);
+
+ tasklet_kill(&hw->phy_task);
+
+ spin_lock_irq(&hw->hw_lock);
+ hw->intr_mask = 0;
+
+ if (hw->ports > 1) {
+ skge_write32(hw, B0_IMSK, 0);
+ skge_read32(hw, B0_IMSK);
+ free_irq(pdev->irq, hw);
+ }
+ spin_unlock_irq(&hw->hw_lock);
+
+ skge_write16(hw, B0_LED, LED_STAT_OFF);
+ skge_write8(hw, B0_CTST, CS_RST_SET);
+
+ if (hw->ports > 1)
+ free_irq(pdev->irq, hw);
+ pci_release_regions(pdev);
+ pci_disable_device(pdev);
+ if (dev1)
+ free_netdev(dev1);
+ free_netdev(dev0);
+
+ iounmap(hw->regs);
+ kfree(hw);
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int skge_suspend(struct device *dev)
+{
+ struct pci_dev *pdev = to_pci_dev(dev);
+ struct skge_hw *hw = pci_get_drvdata(pdev);
+ int i;
+
+ if (!hw)
+ return 0;
+
+ for (i = 0; i < hw->ports; i++) {
+ struct net_device *dev = hw->dev[i];
+ struct skge_port *skge = netdev_priv(dev);
+
+ if (netif_running(dev))
+ skge_down(dev);
+
+ if (skge->wol)
+ skge_wol_init(skge);
+ }
+
+ skge_write32(hw, B0_IMSK, 0);
+
+ return 0;
+}
+
+static int skge_resume(struct device *dev)
+{
+ struct pci_dev *pdev = to_pci_dev(dev);
+ struct skge_hw *hw = pci_get_drvdata(pdev);
+ int i, err;
+
+ if (!hw)
+ return 0;
+
+ err = skge_reset(hw);
+ if (err)
+ goto out;
+
+ for (i = 0; i < hw->ports; i++) {
+ struct net_device *dev = hw->dev[i];
+
+ if (netif_running(dev)) {
+ err = skge_up(dev);
+
+ if (err) {
+ netdev_err(dev, "could not up: %d\n", err);
+ dev_close(dev);
+ goto out;
+ }
+ }
+ }
+out:
+ return err;
+}
+
+static SIMPLE_DEV_PM_OPS(skge_pm_ops, skge_suspend, skge_resume);
+#define SKGE_PM_OPS (&skge_pm_ops)
+
+#else
+
+#define SKGE_PM_OPS NULL
+#endif /* CONFIG_PM_SLEEP */
+
+static void skge_shutdown(struct pci_dev *pdev)
+{
+ struct skge_hw *hw = pci_get_drvdata(pdev);
+ int i;
+
+ if (!hw)
+ return;
+
+ for (i = 0; i < hw->ports; i++) {
+ struct net_device *dev = hw->dev[i];
+ struct skge_port *skge = netdev_priv(dev);
+
+ if (skge->wol)
+ skge_wol_init(skge);
+ }
+
+ pci_wake_from_d3(pdev, device_may_wakeup(&pdev->dev));
+ pci_set_power_state(pdev, PCI_D3hot);
+}
+
+static struct pci_driver skge_driver = {
+ .name = DRV_NAME,
+ .id_table = skge_id_table,
+ .probe = skge_probe,
+ .remove = skge_remove,
+ .shutdown = skge_shutdown,
+ .driver.pm = SKGE_PM_OPS,
+};
+
+static struct dmi_system_id skge_32bit_dma_boards[] = {
+ {
+ .ident = "Gigabyte nForce boards",
+ .matches = {
+ DMI_MATCH(DMI_BOARD_VENDOR, "Gigabyte Technology Co"),
+ DMI_MATCH(DMI_BOARD_NAME, "nForce"),
+ },
+ },
+ {
+ .ident = "ASUS P5NSLI",
+ .matches = {
+ DMI_MATCH(DMI_BOARD_VENDOR, "ASUSTeK Computer INC."),
+ DMI_MATCH(DMI_BOARD_NAME, "P5NSLI")
+ },
+ },
+ {
+ .ident = "FUJITSU SIEMENS A8NE-FM",
+ .matches = {
+ DMI_MATCH(DMI_BOARD_VENDOR, "ASUSTek Computer INC."),
+ DMI_MATCH(DMI_BOARD_NAME, "A8NE-FM")
+ },
+ },
+ {}
+};
+
+static int __init skge_init_module(void)
+{
+ if (dmi_check_system(skge_32bit_dma_boards))
+ only_32bit_dma = 1;
+ skge_debug_init();
+ return pci_register_driver(&skge_driver);
+}
+
+static void __exit skge_cleanup_module(void)
+{
+ pci_unregister_driver(&skge_driver);
+ skge_debug_cleanup();
+}
+
+module_init(skge_init_module);
+module_exit(skge_cleanup_module);
Code Review / kvmfornfv.git / blobdiff