--- /dev/null
+/* Intel(R) Gigabit Ethernet Linux driver
+ * Copyright(c) 2007-2014 Intel Corporation.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program; if not, see <http://www.gnu.org/licenses/>.
+ *
+ * The full GNU General Public License is included in this distribution in
+ * the file called "COPYING".
+ *
+ * Contact Information:
+ * e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+ * Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+ */
+
+/* e1000_82575
+ * e1000_82576
+ */
+
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
+#include <linux/types.h>
+#include <linux/if_ether.h>
+#include <linux/i2c.h>
+
+#include "e1000_mac.h"
+#include "e1000_82575.h"
+#include "e1000_i210.h"
+
+static s32 igb_get_invariants_82575(struct e1000_hw *);
+static s32 igb_acquire_phy_82575(struct e1000_hw *);
+static void igb_release_phy_82575(struct e1000_hw *);
+static s32 igb_acquire_nvm_82575(struct e1000_hw *);
+static void igb_release_nvm_82575(struct e1000_hw *);
+static s32 igb_check_for_link_82575(struct e1000_hw *);
+static s32 igb_get_cfg_done_82575(struct e1000_hw *);
+static s32 igb_init_hw_82575(struct e1000_hw *);
+static s32 igb_phy_hw_reset_sgmii_82575(struct e1000_hw *);
+static s32 igb_read_phy_reg_sgmii_82575(struct e1000_hw *, u32, u16 *);
+static s32 igb_read_phy_reg_82580(struct e1000_hw *, u32, u16 *);
+static s32 igb_write_phy_reg_82580(struct e1000_hw *, u32, u16);
+static s32 igb_reset_hw_82575(struct e1000_hw *);
+static s32 igb_reset_hw_82580(struct e1000_hw *);
+static s32 igb_set_d0_lplu_state_82575(struct e1000_hw *, bool);
+static s32 igb_set_d0_lplu_state_82580(struct e1000_hw *, bool);
+static s32 igb_set_d3_lplu_state_82580(struct e1000_hw *, bool);
+static s32 igb_setup_copper_link_82575(struct e1000_hw *);
+static s32 igb_setup_serdes_link_82575(struct e1000_hw *);
+static s32 igb_write_phy_reg_sgmii_82575(struct e1000_hw *, u32, u16);
+static void igb_clear_hw_cntrs_82575(struct e1000_hw *);
+static s32 igb_acquire_swfw_sync_82575(struct e1000_hw *, u16);
+static s32 igb_get_pcs_speed_and_duplex_82575(struct e1000_hw *, u16 *,
+ u16 *);
+static s32 igb_get_phy_id_82575(struct e1000_hw *);
+static void igb_release_swfw_sync_82575(struct e1000_hw *, u16);
+static bool igb_sgmii_active_82575(struct e1000_hw *);
+static s32 igb_reset_init_script_82575(struct e1000_hw *);
+static s32 igb_read_mac_addr_82575(struct e1000_hw *);
+static s32 igb_set_pcie_completion_timeout(struct e1000_hw *hw);
+static s32 igb_reset_mdicnfg_82580(struct e1000_hw *hw);
+static s32 igb_validate_nvm_checksum_82580(struct e1000_hw *hw);
+static s32 igb_update_nvm_checksum_82580(struct e1000_hw *hw);
+static s32 igb_validate_nvm_checksum_i350(struct e1000_hw *hw);
+static s32 igb_update_nvm_checksum_i350(struct e1000_hw *hw);
+static const u16 e1000_82580_rxpbs_table[] = {
+ 36, 72, 144, 1, 2, 4, 8, 16, 35, 70, 140 };
+
+/**
+ * igb_sgmii_uses_mdio_82575 - Determine if I2C pins are for external MDIO
+ * @hw: pointer to the HW structure
+ *
+ * Called to determine if the I2C pins are being used for I2C or as an
+ * external MDIO interface since the two options are mutually exclusive.
+ **/
+static bool igb_sgmii_uses_mdio_82575(struct e1000_hw *hw)
+{
+ u32 reg = 0;
+ bool ext_mdio = false;
+
+ switch (hw->mac.type) {
+ case e1000_82575:
+ case e1000_82576:
+ reg = rd32(E1000_MDIC);
+ ext_mdio = !!(reg & E1000_MDIC_DEST);
+ break;
+ case e1000_82580:
+ case e1000_i350:
+ case e1000_i354:
+ case e1000_i210:
+ case e1000_i211:
+ reg = rd32(E1000_MDICNFG);
+ ext_mdio = !!(reg & E1000_MDICNFG_EXT_MDIO);
+ break;
+ default:
+ break;
+ }
+ return ext_mdio;
+}
+
+/**
+ * igb_check_for_link_media_swap - Check which M88E1112 interface linked
+ * @hw: pointer to the HW structure
+ *
+ * Poll the M88E1112 interfaces to see which interface achieved link.
+ */
+static s32 igb_check_for_link_media_swap(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 data;
+ u8 port = 0;
+
+ /* Check the copper medium. */
+ ret_val = phy->ops.write_reg(hw, E1000_M88E1112_PAGE_ADDR, 0);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = phy->ops.read_reg(hw, E1000_M88E1112_STATUS, &data);
+ if (ret_val)
+ return ret_val;
+
+ if (data & E1000_M88E1112_STATUS_LINK)
+ port = E1000_MEDIA_PORT_COPPER;
+
+ /* Check the other medium. */
+ ret_val = phy->ops.write_reg(hw, E1000_M88E1112_PAGE_ADDR, 1);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = phy->ops.read_reg(hw, E1000_M88E1112_STATUS, &data);
+ if (ret_val)
+ return ret_val;
+
+ /* reset page to 0 */
+ ret_val = phy->ops.write_reg(hw, E1000_M88E1112_PAGE_ADDR, 0);
+ if (ret_val)
+ return ret_val;
+
+ if (data & E1000_M88E1112_STATUS_LINK)
+ port = E1000_MEDIA_PORT_OTHER;
+
+ /* Determine if a swap needs to happen. */
+ if (port && (hw->dev_spec._82575.media_port != port)) {
+ hw->dev_spec._82575.media_port = port;
+ hw->dev_spec._82575.media_changed = true;
+ } else {
+ ret_val = igb_check_for_link_82575(hw);
+ }
+
+ return 0;
+}
+
+/**
+ * igb_init_phy_params_82575 - Init PHY func ptrs.
+ * @hw: pointer to the HW structure
+ **/
+static s32 igb_init_phy_params_82575(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val = 0;
+ u32 ctrl_ext;
+
+ if (hw->phy.media_type != e1000_media_type_copper) {
+ phy->type = e1000_phy_none;
+ goto out;
+ }
+
+ phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT;
+ phy->reset_delay_us = 100;
+
+ ctrl_ext = rd32(E1000_CTRL_EXT);
+
+ if (igb_sgmii_active_82575(hw)) {
+ phy->ops.reset = igb_phy_hw_reset_sgmii_82575;
+ ctrl_ext |= E1000_CTRL_I2C_ENA;
+ } else {
+ phy->ops.reset = igb_phy_hw_reset;
+ ctrl_ext &= ~E1000_CTRL_I2C_ENA;
+ }
+
+ wr32(E1000_CTRL_EXT, ctrl_ext);
+ igb_reset_mdicnfg_82580(hw);
+
+ if (igb_sgmii_active_82575(hw) && !igb_sgmii_uses_mdio_82575(hw)) {
+ phy->ops.read_reg = igb_read_phy_reg_sgmii_82575;
+ phy->ops.write_reg = igb_write_phy_reg_sgmii_82575;
+ } else {
+ switch (hw->mac.type) {
+ case e1000_82580:
+ case e1000_i350:
+ case e1000_i354:
+ phy->ops.read_reg = igb_read_phy_reg_82580;
+ phy->ops.write_reg = igb_write_phy_reg_82580;
+ break;
+ case e1000_i210:
+ case e1000_i211:
+ phy->ops.read_reg = igb_read_phy_reg_gs40g;
+ phy->ops.write_reg = igb_write_phy_reg_gs40g;
+ break;
+ default:
+ phy->ops.read_reg = igb_read_phy_reg_igp;
+ phy->ops.write_reg = igb_write_phy_reg_igp;
+ }
+ }
+
+ /* set lan id */
+ hw->bus.func = (rd32(E1000_STATUS) & E1000_STATUS_FUNC_MASK) >>
+ E1000_STATUS_FUNC_SHIFT;
+
+ /* Set phy->phy_addr and phy->id. */
+ ret_val = igb_get_phy_id_82575(hw);
+ if (ret_val)
+ return ret_val;
+
+ /* Verify phy id and set remaining function pointers */
+ switch (phy->id) {
+ case M88E1543_E_PHY_ID:
+ case I347AT4_E_PHY_ID:
+ case M88E1112_E_PHY_ID:
+ case M88E1111_I_PHY_ID:
+ phy->type = e1000_phy_m88;
+ phy->ops.check_polarity = igb_check_polarity_m88;
+ phy->ops.get_phy_info = igb_get_phy_info_m88;
+ if (phy->id != M88E1111_I_PHY_ID)
+ phy->ops.get_cable_length =
+ igb_get_cable_length_m88_gen2;
+ else
+ phy->ops.get_cable_length = igb_get_cable_length_m88;
+ phy->ops.force_speed_duplex = igb_phy_force_speed_duplex_m88;
+ /* Check if this PHY is confgured for media swap. */
+ if (phy->id == M88E1112_E_PHY_ID) {
+ u16 data;
+
+ ret_val = phy->ops.write_reg(hw,
+ E1000_M88E1112_PAGE_ADDR,
+ 2);
+ if (ret_val)
+ goto out;
+
+ ret_val = phy->ops.read_reg(hw,
+ E1000_M88E1112_MAC_CTRL_1,
+ &data);
+ if (ret_val)
+ goto out;
+
+ data = (data & E1000_M88E1112_MAC_CTRL_1_MODE_MASK) >>
+ E1000_M88E1112_MAC_CTRL_1_MODE_SHIFT;
+ if (data == E1000_M88E1112_AUTO_COPPER_SGMII ||
+ data == E1000_M88E1112_AUTO_COPPER_BASEX)
+ hw->mac.ops.check_for_link =
+ igb_check_for_link_media_swap;
+ }
+ break;
+ case IGP03E1000_E_PHY_ID:
+ phy->type = e1000_phy_igp_3;
+ phy->ops.get_phy_info = igb_get_phy_info_igp;
+ phy->ops.get_cable_length = igb_get_cable_length_igp_2;
+ phy->ops.force_speed_duplex = igb_phy_force_speed_duplex_igp;
+ phy->ops.set_d0_lplu_state = igb_set_d0_lplu_state_82575;
+ phy->ops.set_d3_lplu_state = igb_set_d3_lplu_state;
+ break;
+ case I82580_I_PHY_ID:
+ case I350_I_PHY_ID:
+ phy->type = e1000_phy_82580;
+ phy->ops.force_speed_duplex =
+ igb_phy_force_speed_duplex_82580;
+ phy->ops.get_cable_length = igb_get_cable_length_82580;
+ phy->ops.get_phy_info = igb_get_phy_info_82580;
+ phy->ops.set_d0_lplu_state = igb_set_d0_lplu_state_82580;
+ phy->ops.set_d3_lplu_state = igb_set_d3_lplu_state_82580;
+ break;
+ case I210_I_PHY_ID:
+ phy->type = e1000_phy_i210;
+ phy->ops.check_polarity = igb_check_polarity_m88;
+ phy->ops.get_phy_info = igb_get_phy_info_m88;
+ phy->ops.get_cable_length = igb_get_cable_length_m88_gen2;
+ phy->ops.set_d0_lplu_state = igb_set_d0_lplu_state_82580;
+ phy->ops.set_d3_lplu_state = igb_set_d3_lplu_state_82580;
+ phy->ops.force_speed_duplex = igb_phy_force_speed_duplex_m88;
+ break;
+ default:
+ ret_val = -E1000_ERR_PHY;
+ goto out;
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * igb_init_nvm_params_82575 - Init NVM func ptrs.
+ * @hw: pointer to the HW structure
+ **/
+static s32 igb_init_nvm_params_82575(struct e1000_hw *hw)
+{
+ struct e1000_nvm_info *nvm = &hw->nvm;
+ u32 eecd = rd32(E1000_EECD);
+ u16 size;
+
+ size = (u16)((eecd & E1000_EECD_SIZE_EX_MASK) >>
+ E1000_EECD_SIZE_EX_SHIFT);
+
+ /* Added to a constant, "size" becomes the left-shift value
+ * for setting word_size.
+ */
+ size += NVM_WORD_SIZE_BASE_SHIFT;
+
+ /* Just in case size is out of range, cap it to the largest
+ * EEPROM size supported
+ */
+ if (size > 15)
+ size = 15;
+
+ nvm->word_size = 1 << size;
+ nvm->opcode_bits = 8;
+ nvm->delay_usec = 1;
+
+ switch (nvm->override) {
+ case e1000_nvm_override_spi_large:
+ nvm->page_size = 32;
+ nvm->address_bits = 16;
+ break;
+ case e1000_nvm_override_spi_small:
+ nvm->page_size = 8;
+ nvm->address_bits = 8;
+ break;
+ default:
+ nvm->page_size = eecd & E1000_EECD_ADDR_BITS ? 32 : 8;
+ nvm->address_bits = eecd & E1000_EECD_ADDR_BITS ?
+ 16 : 8;
+ break;
+ }
+ if (nvm->word_size == (1 << 15))
+ nvm->page_size = 128;
+
+ nvm->type = e1000_nvm_eeprom_spi;
+
+ /* NVM Function Pointers */
+ nvm->ops.acquire = igb_acquire_nvm_82575;
+ nvm->ops.release = igb_release_nvm_82575;
+ nvm->ops.write = igb_write_nvm_spi;
+ nvm->ops.validate = igb_validate_nvm_checksum;
+ nvm->ops.update = igb_update_nvm_checksum;
+ if (nvm->word_size < (1 << 15))
+ nvm->ops.read = igb_read_nvm_eerd;
+ else
+ nvm->ops.read = igb_read_nvm_spi;
+
+ /* override generic family function pointers for specific descendants */
+ switch (hw->mac.type) {
+ case e1000_82580:
+ nvm->ops.validate = igb_validate_nvm_checksum_82580;
+ nvm->ops.update = igb_update_nvm_checksum_82580;
+ break;
+ case e1000_i354:
+ case e1000_i350:
+ nvm->ops.validate = igb_validate_nvm_checksum_i350;
+ nvm->ops.update = igb_update_nvm_checksum_i350;
+ break;
+ default:
+ break;
+ }
+
+ return 0;
+}
+
+/**
+ * igb_init_mac_params_82575 - Init MAC func ptrs.
+ * @hw: pointer to the HW structure
+ **/
+static s32 igb_init_mac_params_82575(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+ struct e1000_dev_spec_82575 *dev_spec = &hw->dev_spec._82575;
+
+ /* Set mta register count */
+ mac->mta_reg_count = 128;
+ /* Set rar entry count */
+ switch (mac->type) {
+ case e1000_82576:
+ mac->rar_entry_count = E1000_RAR_ENTRIES_82576;
+ break;
+ case e1000_82580:
+ mac->rar_entry_count = E1000_RAR_ENTRIES_82580;
+ break;
+ case e1000_i350:
+ case e1000_i354:
+ mac->rar_entry_count = E1000_RAR_ENTRIES_I350;
+ break;
+ default:
+ mac->rar_entry_count = E1000_RAR_ENTRIES_82575;
+ break;
+ }
+ /* reset */
+ if (mac->type >= e1000_82580)
+ mac->ops.reset_hw = igb_reset_hw_82580;
+ else
+ mac->ops.reset_hw = igb_reset_hw_82575;
+
+ if (mac->type >= e1000_i210) {
+ mac->ops.acquire_swfw_sync = igb_acquire_swfw_sync_i210;
+ mac->ops.release_swfw_sync = igb_release_swfw_sync_i210;
+
+ } else {
+ mac->ops.acquire_swfw_sync = igb_acquire_swfw_sync_82575;
+ mac->ops.release_swfw_sync = igb_release_swfw_sync_82575;
+ }
+
+ /* Set if part includes ASF firmware */
+ mac->asf_firmware_present = true;
+ /* Set if manageability features are enabled. */
+ mac->arc_subsystem_valid =
+ (rd32(E1000_FWSM) & E1000_FWSM_MODE_MASK)
+ ? true : false;
+ /* enable EEE on i350 parts and later parts */
+ if (mac->type >= e1000_i350)
+ dev_spec->eee_disable = false;
+ else
+ dev_spec->eee_disable = true;
+ /* Allow a single clear of the SW semaphore on I210 and newer */
+ if (mac->type >= e1000_i210)
+ dev_spec->clear_semaphore_once = true;
+ /* physical interface link setup */
+ mac->ops.setup_physical_interface =
+ (hw->phy.media_type == e1000_media_type_copper)
+ ? igb_setup_copper_link_82575
+ : igb_setup_serdes_link_82575;
+
+ if (mac->type == e1000_82580) {
+ switch (hw->device_id) {
+ /* feature not supported on these id's */
+ case E1000_DEV_ID_DH89XXCC_SGMII:
+ case E1000_DEV_ID_DH89XXCC_SERDES:
+ case E1000_DEV_ID_DH89XXCC_BACKPLANE:
+ case E1000_DEV_ID_DH89XXCC_SFP:
+ break;
+ default:
+ hw->dev_spec._82575.mas_capable = true;
+ break;
+ }
+ }
+ return 0;
+}
+
+/**
+ * igb_set_sfp_media_type_82575 - derives SFP module media type.
+ * @hw: pointer to the HW structure
+ *
+ * The media type is chosen based on SFP module.
+ * compatibility flags retrieved from SFP ID EEPROM.
+ **/
+static s32 igb_set_sfp_media_type_82575(struct e1000_hw *hw)
+{
+ s32 ret_val = E1000_ERR_CONFIG;
+ u32 ctrl_ext = 0;
+ struct e1000_dev_spec_82575 *dev_spec = &hw->dev_spec._82575;
+ struct e1000_sfp_flags *eth_flags = &dev_spec->eth_flags;
+ u8 tranceiver_type = 0;
+ s32 timeout = 3;
+
+ /* Turn I2C interface ON and power on sfp cage */
+ ctrl_ext = rd32(E1000_CTRL_EXT);
+ ctrl_ext &= ~E1000_CTRL_EXT_SDP3_DATA;
+ wr32(E1000_CTRL_EXT, ctrl_ext | E1000_CTRL_I2C_ENA);
+
+ wrfl();
+
+ /* Read SFP module data */
+ while (timeout) {
+ ret_val = igb_read_sfp_data_byte(hw,
+ E1000_I2CCMD_SFP_DATA_ADDR(E1000_SFF_IDENTIFIER_OFFSET),
+ &tranceiver_type);
+ if (ret_val == 0)
+ break;
+ msleep(100);
+ timeout--;
+ }
+ if (ret_val != 0)
+ goto out;
+
+ ret_val = igb_read_sfp_data_byte(hw,
+ E1000_I2CCMD_SFP_DATA_ADDR(E1000_SFF_ETH_FLAGS_OFFSET),
+ (u8 *)eth_flags);
+ if (ret_val != 0)
+ goto out;
+
+ /* Check if there is some SFP module plugged and powered */
+ if ((tranceiver_type == E1000_SFF_IDENTIFIER_SFP) ||
+ (tranceiver_type == E1000_SFF_IDENTIFIER_SFF)) {
+ dev_spec->module_plugged = true;
+ if (eth_flags->e1000_base_lx || eth_flags->e1000_base_sx) {
+ hw->phy.media_type = e1000_media_type_internal_serdes;
+ } else if (eth_flags->e100_base_fx) {
+ dev_spec->sgmii_active = true;
+ hw->phy.media_type = e1000_media_type_internal_serdes;
+ } else if (eth_flags->e1000_base_t) {
+ dev_spec->sgmii_active = true;
+ hw->phy.media_type = e1000_media_type_copper;
+ } else {
+ hw->phy.media_type = e1000_media_type_unknown;
+ hw_dbg("PHY module has not been recognized\n");
+ goto out;
+ }
+ } else {
+ hw->phy.media_type = e1000_media_type_unknown;
+ }
+ ret_val = 0;
+out:
+ /* Restore I2C interface setting */
+ wr32(E1000_CTRL_EXT, ctrl_ext);
+ return ret_val;
+}
+
+static s32 igb_get_invariants_82575(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+ struct e1000_dev_spec_82575 *dev_spec = &hw->dev_spec._82575;
+ s32 ret_val;
+ u32 ctrl_ext = 0;
+ u32 link_mode = 0;
+
+ switch (hw->device_id) {
+ case E1000_DEV_ID_82575EB_COPPER:
+ case E1000_DEV_ID_82575EB_FIBER_SERDES:
+ case E1000_DEV_ID_82575GB_QUAD_COPPER:
+ mac->type = e1000_82575;
+ break;
+ case E1000_DEV_ID_82576:
+ case E1000_DEV_ID_82576_NS:
+ case E1000_DEV_ID_82576_NS_SERDES:
+ case E1000_DEV_ID_82576_FIBER:
+ case E1000_DEV_ID_82576_SERDES:
+ case E1000_DEV_ID_82576_QUAD_COPPER:
+ case E1000_DEV_ID_82576_QUAD_COPPER_ET2:
+ case E1000_DEV_ID_82576_SERDES_QUAD:
+ mac->type = e1000_82576;
+ break;
+ case E1000_DEV_ID_82580_COPPER:
+ case E1000_DEV_ID_82580_FIBER:
+ case E1000_DEV_ID_82580_QUAD_FIBER:
+ case E1000_DEV_ID_82580_SERDES:
+ case E1000_DEV_ID_82580_SGMII:
+ case E1000_DEV_ID_82580_COPPER_DUAL:
+ case E1000_DEV_ID_DH89XXCC_SGMII:
+ case E1000_DEV_ID_DH89XXCC_SERDES:
+ case E1000_DEV_ID_DH89XXCC_BACKPLANE:
+ case E1000_DEV_ID_DH89XXCC_SFP:
+ mac->type = e1000_82580;
+ break;
+ case E1000_DEV_ID_I350_COPPER:
+ case E1000_DEV_ID_I350_FIBER:
+ case E1000_DEV_ID_I350_SERDES:
+ case E1000_DEV_ID_I350_SGMII:
+ mac->type = e1000_i350;
+ break;
+ case E1000_DEV_ID_I210_COPPER:
+ case E1000_DEV_ID_I210_FIBER:
+ case E1000_DEV_ID_I210_SERDES:
+ case E1000_DEV_ID_I210_SGMII:
+ case E1000_DEV_ID_I210_COPPER_FLASHLESS:
+ case E1000_DEV_ID_I210_SERDES_FLASHLESS:
+ mac->type = e1000_i210;
+ break;
+ case E1000_DEV_ID_I211_COPPER:
+ mac->type = e1000_i211;
+ break;
+ case E1000_DEV_ID_I354_BACKPLANE_1GBPS:
+ case E1000_DEV_ID_I354_SGMII:
+ case E1000_DEV_ID_I354_BACKPLANE_2_5GBPS:
+ mac->type = e1000_i354;
+ break;
+ default:
+ return -E1000_ERR_MAC_INIT;
+ }
+
+ /* Set media type */
+ /* The 82575 uses bits 22:23 for link mode. The mode can be changed
+ * based on the EEPROM. We cannot rely upon device ID. There
+ * is no distinguishable difference between fiber and internal
+ * SerDes mode on the 82575. There can be an external PHY attached
+ * on the SGMII interface. For this, we'll set sgmii_active to true.
+ */
+ hw->phy.media_type = e1000_media_type_copper;
+ dev_spec->sgmii_active = false;
+ dev_spec->module_plugged = false;
+
+ ctrl_ext = rd32(E1000_CTRL_EXT);
+
+ link_mode = ctrl_ext & E1000_CTRL_EXT_LINK_MODE_MASK;
+ switch (link_mode) {
+ case E1000_CTRL_EXT_LINK_MODE_1000BASE_KX:
+ hw->phy.media_type = e1000_media_type_internal_serdes;
+ break;
+ case E1000_CTRL_EXT_LINK_MODE_SGMII:
+ /* Get phy control interface type set (MDIO vs. I2C)*/
+ if (igb_sgmii_uses_mdio_82575(hw)) {
+ hw->phy.media_type = e1000_media_type_copper;
+ dev_spec->sgmii_active = true;
+ break;
+ }
+ /* fall through for I2C based SGMII */
+ case E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES:
+ /* read media type from SFP EEPROM */
+ ret_val = igb_set_sfp_media_type_82575(hw);
+ if ((ret_val != 0) ||
+ (hw->phy.media_type == e1000_media_type_unknown)) {
+ /* If media type was not identified then return media
+ * type defined by the CTRL_EXT settings.
+ */
+ hw->phy.media_type = e1000_media_type_internal_serdes;
+
+ if (link_mode == E1000_CTRL_EXT_LINK_MODE_SGMII) {
+ hw->phy.media_type = e1000_media_type_copper;
+ dev_spec->sgmii_active = true;
+ }
+
+ break;
+ }
+
+ /* do not change link mode for 100BaseFX */
+ if (dev_spec->eth_flags.e100_base_fx)
+ break;
+
+ /* change current link mode setting */
+ ctrl_ext &= ~E1000_CTRL_EXT_LINK_MODE_MASK;
+
+ if (hw->phy.media_type == e1000_media_type_copper)
+ ctrl_ext |= E1000_CTRL_EXT_LINK_MODE_SGMII;
+ else
+ ctrl_ext |= E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES;
+
+ wr32(E1000_CTRL_EXT, ctrl_ext);
+
+ break;
+ default:
+ break;
+ }
+
+ /* mac initialization and operations */
+ ret_val = igb_init_mac_params_82575(hw);
+ if (ret_val)
+ goto out;
+
+ /* NVM initialization */
+ ret_val = igb_init_nvm_params_82575(hw);
+ switch (hw->mac.type) {
+ case e1000_i210:
+ case e1000_i211:
+ ret_val = igb_init_nvm_params_i210(hw);
+ break;
+ default:
+ break;
+ }
+
+ if (ret_val)
+ goto out;
+
+ /* if part supports SR-IOV then initialize mailbox parameters */
+ switch (mac->type) {
+ case e1000_82576:
+ case e1000_i350:
+ igb_init_mbx_params_pf(hw);
+ break;
+ default:
+ break;
+ }
+
+ /* setup PHY parameters */
+ ret_val = igb_init_phy_params_82575(hw);
+
+out:
+ return ret_val;
+}
+
+/**
+ * igb_acquire_phy_82575 - Acquire rights to access PHY
+ * @hw: pointer to the HW structure
+ *
+ * Acquire access rights to the correct PHY. This is a
+ * function pointer entry point called by the api module.
+ **/
+static s32 igb_acquire_phy_82575(struct e1000_hw *hw)
+{
+ u16 mask = E1000_SWFW_PHY0_SM;
+
+ if (hw->bus.func == E1000_FUNC_1)
+ mask = E1000_SWFW_PHY1_SM;
+ else if (hw->bus.func == E1000_FUNC_2)
+ mask = E1000_SWFW_PHY2_SM;
+ else if (hw->bus.func == E1000_FUNC_3)
+ mask = E1000_SWFW_PHY3_SM;
+
+ return hw->mac.ops.acquire_swfw_sync(hw, mask);
+}
+
+/**
+ * igb_release_phy_82575 - Release rights to access PHY
+ * @hw: pointer to the HW structure
+ *
+ * A wrapper to release access rights to the correct PHY. This is a
+ * function pointer entry point called by the api module.
+ **/
+static void igb_release_phy_82575(struct e1000_hw *hw)
+{
+ u16 mask = E1000_SWFW_PHY0_SM;
+
+ if (hw->bus.func == E1000_FUNC_1)
+ mask = E1000_SWFW_PHY1_SM;
+ else if (hw->bus.func == E1000_FUNC_2)
+ mask = E1000_SWFW_PHY2_SM;
+ else if (hw->bus.func == E1000_FUNC_3)
+ mask = E1000_SWFW_PHY3_SM;
+
+ hw->mac.ops.release_swfw_sync(hw, mask);
+}
+
+/**
+ * igb_read_phy_reg_sgmii_82575 - Read PHY register using sgmii
+ * @hw: pointer to the HW structure
+ * @offset: register offset to be read
+ * @data: pointer to the read data
+ *
+ * Reads the PHY register at offset using the serial gigabit media independent
+ * interface and stores the retrieved information in data.
+ **/
+static s32 igb_read_phy_reg_sgmii_82575(struct e1000_hw *hw, u32 offset,
+ u16 *data)
+{
+ s32 ret_val = -E1000_ERR_PARAM;
+
+ if (offset > E1000_MAX_SGMII_PHY_REG_ADDR) {
+ hw_dbg("PHY Address %u is out of range\n", offset);
+ goto out;
+ }
+
+ ret_val = hw->phy.ops.acquire(hw);
+ if (ret_val)
+ goto out;
+
+ ret_val = igb_read_phy_reg_i2c(hw, offset, data);
+
+ hw->phy.ops.release(hw);
+
+out:
+ return ret_val;
+}
+
+/**
+ * igb_write_phy_reg_sgmii_82575 - Write PHY register using sgmii
+ * @hw: pointer to the HW structure
+ * @offset: register offset to write to
+ * @data: data to write at register offset
+ *
+ * Writes the data to PHY register at the offset using the serial gigabit
+ * media independent interface.
+ **/
+static s32 igb_write_phy_reg_sgmii_82575(struct e1000_hw *hw, u32 offset,
+ u16 data)
+{
+ s32 ret_val = -E1000_ERR_PARAM;
+
+
+ if (offset > E1000_MAX_SGMII_PHY_REG_ADDR) {
+ hw_dbg("PHY Address %d is out of range\n", offset);
+ goto out;
+ }
+
+ ret_val = hw->phy.ops.acquire(hw);
+ if (ret_val)
+ goto out;
+
+ ret_val = igb_write_phy_reg_i2c(hw, offset, data);
+
+ hw->phy.ops.release(hw);
+
+out:
+ return ret_val;
+}
+
+/**
+ * igb_get_phy_id_82575 - Retrieve PHY addr and id
+ * @hw: pointer to the HW structure
+ *
+ * Retrieves the PHY address and ID for both PHY's which do and do not use
+ * sgmi interface.
+ **/
+static s32 igb_get_phy_id_82575(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val = 0;
+ u16 phy_id;
+ u32 ctrl_ext;
+ u32 mdic;
+
+ /* Extra read required for some PHY's on i354 */
+ if (hw->mac.type == e1000_i354)
+ igb_get_phy_id(hw);
+
+ /* For SGMII PHYs, we try the list of possible addresses until
+ * we find one that works. For non-SGMII PHYs
+ * (e.g. integrated copper PHYs), an address of 1 should
+ * work. The result of this function should mean phy->phy_addr
+ * and phy->id are set correctly.
+ */
+ if (!(igb_sgmii_active_82575(hw))) {
+ phy->addr = 1;
+ ret_val = igb_get_phy_id(hw);
+ goto out;
+ }
+
+ if (igb_sgmii_uses_mdio_82575(hw)) {
+ switch (hw->mac.type) {
+ case e1000_82575:
+ case e1000_82576:
+ mdic = rd32(E1000_MDIC);
+ mdic &= E1000_MDIC_PHY_MASK;
+ phy->addr = mdic >> E1000_MDIC_PHY_SHIFT;
+ break;
+ case e1000_82580:
+ case e1000_i350:
+ case e1000_i354:
+ case e1000_i210:
+ case e1000_i211:
+ mdic = rd32(E1000_MDICNFG);
+ mdic &= E1000_MDICNFG_PHY_MASK;
+ phy->addr = mdic >> E1000_MDICNFG_PHY_SHIFT;
+ break;
+ default:
+ ret_val = -E1000_ERR_PHY;
+ goto out;
+ }
+ ret_val = igb_get_phy_id(hw);
+ goto out;
+ }
+
+ /* Power on sgmii phy if it is disabled */
+ ctrl_ext = rd32(E1000_CTRL_EXT);
+ wr32(E1000_CTRL_EXT, ctrl_ext & ~E1000_CTRL_EXT_SDP3_DATA);
+ wrfl();
+ msleep(300);
+
+ /* The address field in the I2CCMD register is 3 bits and 0 is invalid.
+ * Therefore, we need to test 1-7
+ */
+ for (phy->addr = 1; phy->addr < 8; phy->addr++) {
+ ret_val = igb_read_phy_reg_sgmii_82575(hw, PHY_ID1, &phy_id);
+ if (ret_val == 0) {
+ hw_dbg("Vendor ID 0x%08X read at address %u\n",
+ phy_id, phy->addr);
+ /* At the time of this writing, The M88 part is
+ * the only supported SGMII PHY product.
+ */
+ if (phy_id == M88_VENDOR)
+ break;
+ } else {
+ hw_dbg("PHY address %u was unreadable\n", phy->addr);
+ }
+ }
+
+ /* A valid PHY type couldn't be found. */
+ if (phy->addr == 8) {
+ phy->addr = 0;
+ ret_val = -E1000_ERR_PHY;
+ goto out;
+ } else {
+ ret_val = igb_get_phy_id(hw);
+ }
+
+ /* restore previous sfp cage power state */
+ wr32(E1000_CTRL_EXT, ctrl_ext);
+
+out:
+ return ret_val;
+}
+
+/**
+ * igb_phy_hw_reset_sgmii_82575 - Performs a PHY reset
+ * @hw: pointer to the HW structure
+ *
+ * Resets the PHY using the serial gigabit media independent interface.
+ **/
+static s32 igb_phy_hw_reset_sgmii_82575(struct e1000_hw *hw)
+{
+ s32 ret_val;
+
+ /* This isn't a true "hard" reset, but is the only reset
+ * available to us at this time.
+ */
+
+ hw_dbg("Soft resetting SGMII attached PHY...\n");
+
+ /* SFP documentation requires the following to configure the SPF module
+ * to work on SGMII. No further documentation is given.
+ */
+ ret_val = hw->phy.ops.write_reg(hw, 0x1B, 0x8084);
+ if (ret_val)
+ goto out;
+
+ ret_val = igb_phy_sw_reset(hw);
+
+out:
+ return ret_val;
+}
+
+/**
+ * igb_set_d0_lplu_state_82575 - Set Low Power Linkup D0 state
+ * @hw: pointer to the HW structure
+ * @active: true to enable LPLU, false to disable
+ *
+ * Sets the LPLU D0 state according to the active flag. When
+ * activating LPLU this function also disables smart speed
+ * and vice versa. LPLU will not be activated unless the
+ * device autonegotiation advertisement meets standards of
+ * either 10 or 10/100 or 10/100/1000 at all duplexes.
+ * This is a function pointer entry point only called by
+ * PHY setup routines.
+ **/
+static s32 igb_set_d0_lplu_state_82575(struct e1000_hw *hw, bool active)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val;
+ u16 data;
+
+ ret_val = phy->ops.read_reg(hw, IGP02E1000_PHY_POWER_MGMT, &data);
+ if (ret_val)
+ goto out;
+
+ if (active) {
+ data |= IGP02E1000_PM_D0_LPLU;
+ ret_val = phy->ops.write_reg(hw, IGP02E1000_PHY_POWER_MGMT,
+ data);
+ if (ret_val)
+ goto out;
+
+ /* When LPLU is enabled, we should disable SmartSpeed */
+ ret_val = phy->ops.read_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
+ &data);
+ data &= ~IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val = phy->ops.write_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
+ data);
+ if (ret_val)
+ goto out;
+ } else {
+ data &= ~IGP02E1000_PM_D0_LPLU;
+ ret_val = phy->ops.write_reg(hw, IGP02E1000_PHY_POWER_MGMT,
+ data);
+ /* LPLU and SmartSpeed are mutually exclusive. LPLU is used
+ * during Dx states where the power conservation is most
+ * important. During driver activity we should enable
+ * SmartSpeed, so performance is maintained.
+ */
+ if (phy->smart_speed == e1000_smart_speed_on) {
+ ret_val = phy->ops.read_reg(hw,
+ IGP01E1000_PHY_PORT_CONFIG, &data);
+ if (ret_val)
+ goto out;
+
+ data |= IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val = phy->ops.write_reg(hw,
+ IGP01E1000_PHY_PORT_CONFIG, data);
+ if (ret_val)
+ goto out;
+ } else if (phy->smart_speed == e1000_smart_speed_off) {
+ ret_val = phy->ops.read_reg(hw,
+ IGP01E1000_PHY_PORT_CONFIG, &data);
+ if (ret_val)
+ goto out;
+
+ data &= ~IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val = phy->ops.write_reg(hw,
+ IGP01E1000_PHY_PORT_CONFIG, data);
+ if (ret_val)
+ goto out;
+ }
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * igb_set_d0_lplu_state_82580 - Set Low Power Linkup D0 state
+ * @hw: pointer to the HW structure
+ * @active: true to enable LPLU, false to disable
+ *
+ * Sets the LPLU D0 state according to the active flag. When
+ * activating LPLU this function also disables smart speed
+ * and vice versa. LPLU will not be activated unless the
+ * device autonegotiation advertisement meets standards of
+ * either 10 or 10/100 or 10/100/1000 at all duplexes.
+ * This is a function pointer entry point only called by
+ * PHY setup routines.
+ **/
+static s32 igb_set_d0_lplu_state_82580(struct e1000_hw *hw, bool active)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ u16 data;
+
+ data = rd32(E1000_82580_PHY_POWER_MGMT);
+
+ if (active) {
+ data |= E1000_82580_PM_D0_LPLU;
+
+ /* When LPLU is enabled, we should disable SmartSpeed */
+ data &= ~E1000_82580_PM_SPD;
+ } else {
+ data &= ~E1000_82580_PM_D0_LPLU;
+
+ /* LPLU and SmartSpeed are mutually exclusive. LPLU is used
+ * during Dx states where the power conservation is most
+ * important. During driver activity we should enable
+ * SmartSpeed, so performance is maintained.
+ */
+ if (phy->smart_speed == e1000_smart_speed_on)
+ data |= E1000_82580_PM_SPD;
+ else if (phy->smart_speed == e1000_smart_speed_off)
+ data &= ~E1000_82580_PM_SPD; }
+
+ wr32(E1000_82580_PHY_POWER_MGMT, data);
+ return 0;
+}
+
+/**
+ * igb_set_d3_lplu_state_82580 - Sets low power link up state for D3
+ * @hw: pointer to the HW structure
+ * @active: boolean used to enable/disable lplu
+ *
+ * Success returns 0, Failure returns 1
+ *
+ * The low power link up (lplu) state is set to the power management level D3
+ * and SmartSpeed is disabled when active is true, else clear lplu for D3
+ * and enable Smartspeed. LPLU and Smartspeed are mutually exclusive. LPLU
+ * is used during Dx states where the power conservation is most important.
+ * During driver activity, SmartSpeed should be enabled so performance is
+ * maintained.
+ **/
+static s32 igb_set_d3_lplu_state_82580(struct e1000_hw *hw, bool active)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ u16 data;
+
+ data = rd32(E1000_82580_PHY_POWER_MGMT);
+
+ if (!active) {
+ data &= ~E1000_82580_PM_D3_LPLU;
+ /* LPLU and SmartSpeed are mutually exclusive. LPLU is used
+ * during Dx states where the power conservation is most
+ * important. During driver activity we should enable
+ * SmartSpeed, so performance is maintained.
+ */
+ if (phy->smart_speed == e1000_smart_speed_on)
+ data |= E1000_82580_PM_SPD;
+ else if (phy->smart_speed == e1000_smart_speed_off)
+ data &= ~E1000_82580_PM_SPD;
+ } else if ((phy->autoneg_advertised == E1000_ALL_SPEED_DUPLEX) ||
+ (phy->autoneg_advertised == E1000_ALL_NOT_GIG) ||
+ (phy->autoneg_advertised == E1000_ALL_10_SPEED)) {
+ data |= E1000_82580_PM_D3_LPLU;
+ /* When LPLU is enabled, we should disable SmartSpeed */
+ data &= ~E1000_82580_PM_SPD;
+ }
+
+ wr32(E1000_82580_PHY_POWER_MGMT, data);
+ return 0;
+}
+
+/**
+ * igb_acquire_nvm_82575 - Request for access to EEPROM
+ * @hw: pointer to the HW structure
+ *
+ * Acquire the necessary semaphores for exclusive access to the EEPROM.
+ * Set the EEPROM access request bit and wait for EEPROM access grant bit.
+ * Return successful if access grant bit set, else clear the request for
+ * EEPROM access and return -E1000_ERR_NVM (-1).
+ **/
+static s32 igb_acquire_nvm_82575(struct e1000_hw *hw)
+{
+ s32 ret_val;
+
+ ret_val = hw->mac.ops.acquire_swfw_sync(hw, E1000_SWFW_EEP_SM);
+ if (ret_val)
+ goto out;
+
+ ret_val = igb_acquire_nvm(hw);
+
+ if (ret_val)
+ hw->mac.ops.release_swfw_sync(hw, E1000_SWFW_EEP_SM);
+
+out:
+ return ret_val;
+}
+
+/**
+ * igb_release_nvm_82575 - Release exclusive access to EEPROM
+ * @hw: pointer to the HW structure
+ *
+ * Stop any current commands to the EEPROM and clear the EEPROM request bit,
+ * then release the semaphores acquired.
+ **/
+static void igb_release_nvm_82575(struct e1000_hw *hw)
+{
+ igb_release_nvm(hw);
+ hw->mac.ops.release_swfw_sync(hw, E1000_SWFW_EEP_SM);
+}
+
+/**
+ * igb_acquire_swfw_sync_82575 - Acquire SW/FW semaphore
+ * @hw: pointer to the HW structure
+ * @mask: specifies which semaphore to acquire
+ *
+ * Acquire the SW/FW semaphore to access the PHY or NVM. The mask
+ * will also specify which port we're acquiring the lock for.
+ **/
+static s32 igb_acquire_swfw_sync_82575(struct e1000_hw *hw, u16 mask)
+{
+ u32 swfw_sync;
+ u32 swmask = mask;
+ u32 fwmask = mask << 16;
+ s32 ret_val = 0;
+ s32 i = 0, timeout = 200;
+
+ while (i < timeout) {
+ if (igb_get_hw_semaphore(hw)) {
+ ret_val = -E1000_ERR_SWFW_SYNC;
+ goto out;
+ }
+
+ swfw_sync = rd32(E1000_SW_FW_SYNC);
+ if (!(swfw_sync & (fwmask | swmask)))
+ break;
+
+ /* Firmware currently using resource (fwmask)
+ * or other software thread using resource (swmask)
+ */
+ igb_put_hw_semaphore(hw);
+ mdelay(5);
+ i++;
+ }
+
+ if (i == timeout) {
+ hw_dbg("Driver can't access resource, SW_FW_SYNC timeout.\n");
+ ret_val = -E1000_ERR_SWFW_SYNC;
+ goto out;
+ }
+
+ swfw_sync |= swmask;
+ wr32(E1000_SW_FW_SYNC, swfw_sync);
+
+ igb_put_hw_semaphore(hw);
+
+out:
+ return ret_val;
+}
+
+/**
+ * igb_release_swfw_sync_82575 - Release SW/FW semaphore
+ * @hw: pointer to the HW structure
+ * @mask: specifies which semaphore to acquire
+ *
+ * Release the SW/FW semaphore used to access the PHY or NVM. The mask
+ * will also specify which port we're releasing the lock for.
+ **/
+static void igb_release_swfw_sync_82575(struct e1000_hw *hw, u16 mask)
+{
+ u32 swfw_sync;
+
+ while (igb_get_hw_semaphore(hw) != 0)
+ ; /* Empty */
+
+ swfw_sync = rd32(E1000_SW_FW_SYNC);
+ swfw_sync &= ~mask;
+ wr32(E1000_SW_FW_SYNC, swfw_sync);
+
+ igb_put_hw_semaphore(hw);
+}
+
+/**
+ * igb_get_cfg_done_82575 - Read config done bit
+ * @hw: pointer to the HW structure
+ *
+ * Read the management control register for the config done bit for
+ * completion status. NOTE: silicon which is EEPROM-less will fail trying
+ * to read the config done bit, so an error is *ONLY* logged and returns
+ * 0. If we were to return with error, EEPROM-less silicon
+ * would not be able to be reset or change link.
+ **/
+static s32 igb_get_cfg_done_82575(struct e1000_hw *hw)
+{
+ s32 timeout = PHY_CFG_TIMEOUT;
+ u32 mask = E1000_NVM_CFG_DONE_PORT_0;
+
+ if (hw->bus.func == 1)
+ mask = E1000_NVM_CFG_DONE_PORT_1;
+ else if (hw->bus.func == E1000_FUNC_2)
+ mask = E1000_NVM_CFG_DONE_PORT_2;
+ else if (hw->bus.func == E1000_FUNC_3)
+ mask = E1000_NVM_CFG_DONE_PORT_3;
+
+ while (timeout) {
+ if (rd32(E1000_EEMNGCTL) & mask)
+ break;
+ usleep_range(1000, 2000);
+ timeout--;
+ }
+ if (!timeout)
+ hw_dbg("MNG configuration cycle has not completed.\n");
+
+ /* If EEPROM is not marked present, init the PHY manually */
+ if (((rd32(E1000_EECD) & E1000_EECD_PRES) == 0) &&
+ (hw->phy.type == e1000_phy_igp_3))
+ igb_phy_init_script_igp3(hw);
+
+ return 0;
+}
+
+/**
+ * igb_get_link_up_info_82575 - Get link speed/duplex info
+ * @hw: pointer to the HW structure
+ * @speed: stores the current speed
+ * @duplex: stores the current duplex
+ *
+ * This is a wrapper function, if using the serial gigabit media independent
+ * interface, use PCS to retrieve the link speed and duplex information.
+ * Otherwise, use the generic function to get the link speed and duplex info.
+ **/
+static s32 igb_get_link_up_info_82575(struct e1000_hw *hw, u16 *speed,
+ u16 *duplex)
+{
+ s32 ret_val;
+
+ if (hw->phy.media_type != e1000_media_type_copper)
+ ret_val = igb_get_pcs_speed_and_duplex_82575(hw, speed,
+ duplex);
+ else
+ ret_val = igb_get_speed_and_duplex_copper(hw, speed,
+ duplex);
+
+ return ret_val;
+}
+
+/**
+ * igb_check_for_link_82575 - Check for link
+ * @hw: pointer to the HW structure
+ *
+ * If sgmii is enabled, then use the pcs register to determine link, otherwise
+ * use the generic interface for determining link.
+ **/
+static s32 igb_check_for_link_82575(struct e1000_hw *hw)
+{
+ s32 ret_val;
+ u16 speed, duplex;
+
+ if (hw->phy.media_type != e1000_media_type_copper) {
+ ret_val = igb_get_pcs_speed_and_duplex_82575(hw, &speed,
+ &duplex);
+ /* Use this flag to determine if link needs to be checked or
+ * not. If we have link clear the flag so that we do not
+ * continue to check for link.
+ */
+ hw->mac.get_link_status = !hw->mac.serdes_has_link;
+
+ /* Configure Flow Control now that Auto-Neg has completed.
+ * First, we need to restore the desired flow control
+ * settings because we may have had to re-autoneg with a
+ * different link partner.
+ */
+ ret_val = igb_config_fc_after_link_up(hw);
+ if (ret_val)
+ hw_dbg("Error configuring flow control\n");
+ } else {
+ ret_val = igb_check_for_copper_link(hw);
+ }
+
+ return ret_val;
+}
+
+/**
+ * igb_power_up_serdes_link_82575 - Power up the serdes link after shutdown
+ * @hw: pointer to the HW structure
+ **/
+void igb_power_up_serdes_link_82575(struct e1000_hw *hw)
+{
+ u32 reg;
+
+
+ if ((hw->phy.media_type != e1000_media_type_internal_serdes) &&
+ !igb_sgmii_active_82575(hw))
+ return;
+
+ /* Enable PCS to turn on link */
+ reg = rd32(E1000_PCS_CFG0);
+ reg |= E1000_PCS_CFG_PCS_EN;
+ wr32(E1000_PCS_CFG0, reg);
+
+ /* Power up the laser */
+ reg = rd32(E1000_CTRL_EXT);
+ reg &= ~E1000_CTRL_EXT_SDP3_DATA;
+ wr32(E1000_CTRL_EXT, reg);
+
+ /* flush the write to verify completion */
+ wrfl();
+ usleep_range(1000, 2000);
+}
+
+/**
+ * igb_get_pcs_speed_and_duplex_82575 - Retrieve current speed/duplex
+ * @hw: pointer to the HW structure
+ * @speed: stores the current speed
+ * @duplex: stores the current duplex
+ *
+ * Using the physical coding sub-layer (PCS), retrieve the current speed and
+ * duplex, then store the values in the pointers provided.
+ **/
+static s32 igb_get_pcs_speed_and_duplex_82575(struct e1000_hw *hw, u16 *speed,
+ u16 *duplex)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+ u32 pcs, status;
+
+ /* Set up defaults for the return values of this function */
+ mac->serdes_has_link = false;
+ *speed = 0;
+ *duplex = 0;
+
+ /* Read the PCS Status register for link state. For non-copper mode,
+ * the status register is not accurate. The PCS status register is
+ * used instead.
+ */
+ pcs = rd32(E1000_PCS_LSTAT);
+
+ /* The link up bit determines when link is up on autoneg. The sync ok
+ * gets set once both sides sync up and agree upon link. Stable link
+ * can be determined by checking for both link up and link sync ok
+ */
+ if ((pcs & E1000_PCS_LSTS_LINK_OK) && (pcs & E1000_PCS_LSTS_SYNK_OK)) {
+ mac->serdes_has_link = true;
+
+ /* Detect and store PCS speed */
+ if (pcs & E1000_PCS_LSTS_SPEED_1000)
+ *speed = SPEED_1000;
+ else if (pcs & E1000_PCS_LSTS_SPEED_100)
+ *speed = SPEED_100;
+ else
+ *speed = SPEED_10;
+
+ /* Detect and store PCS duplex */
+ if (pcs & E1000_PCS_LSTS_DUPLEX_FULL)
+ *duplex = FULL_DUPLEX;
+ else
+ *duplex = HALF_DUPLEX;
+
+ /* Check if it is an I354 2.5Gb backplane connection. */
+ if (mac->type == e1000_i354) {
+ status = rd32(E1000_STATUS);
+ if ((status & E1000_STATUS_2P5_SKU) &&
+ !(status & E1000_STATUS_2P5_SKU_OVER)) {
+ *speed = SPEED_2500;
+ *duplex = FULL_DUPLEX;
+ hw_dbg("2500 Mbs, ");
+ hw_dbg("Full Duplex\n");
+ }
+ }
+
+ }
+
+ return 0;
+}
+
+/**
+ * igb_shutdown_serdes_link_82575 - Remove link during power down
+ * @hw: pointer to the HW structure
+ *
+ * In the case of fiber serdes, shut down optics and PCS on driver unload
+ * when management pass thru is not enabled.
+ **/
+void igb_shutdown_serdes_link_82575(struct e1000_hw *hw)
+{
+ u32 reg;
+
+ if (hw->phy.media_type != e1000_media_type_internal_serdes &&
+ igb_sgmii_active_82575(hw))
+ return;
+
+ if (!igb_enable_mng_pass_thru(hw)) {
+ /* Disable PCS to turn off link */
+ reg = rd32(E1000_PCS_CFG0);
+ reg &= ~E1000_PCS_CFG_PCS_EN;
+ wr32(E1000_PCS_CFG0, reg);
+
+ /* shutdown the laser */
+ reg = rd32(E1000_CTRL_EXT);
+ reg |= E1000_CTRL_EXT_SDP3_DATA;
+ wr32(E1000_CTRL_EXT, reg);
+
+ /* flush the write to verify completion */
+ wrfl();
+ usleep_range(1000, 2000);
+ }
+}
+
+/**
+ * igb_reset_hw_82575 - Reset hardware
+ * @hw: pointer to the HW structure
+ *
+ * This resets the hardware into a known state. This is a
+ * function pointer entry point called by the api module.
+ **/
+static s32 igb_reset_hw_82575(struct e1000_hw *hw)
+{
+ u32 ctrl;
+ s32 ret_val;
+
+ /* Prevent the PCI-E bus from sticking if there is no TLP connection
+ * on the last TLP read/write transaction when MAC is reset.
+ */
+ ret_val = igb_disable_pcie_master(hw);
+ if (ret_val)
+ hw_dbg("PCI-E Master disable polling has failed.\n");
+
+ /* set the completion timeout for interface */
+ ret_val = igb_set_pcie_completion_timeout(hw);
+ if (ret_val)
+ hw_dbg("PCI-E Set completion timeout has failed.\n");
+
+ hw_dbg("Masking off all interrupts\n");
+ wr32(E1000_IMC, 0xffffffff);
+
+ wr32(E1000_RCTL, 0);
+ wr32(E1000_TCTL, E1000_TCTL_PSP);
+ wrfl();
+
+ usleep_range(10000, 20000);
+
+ ctrl = rd32(E1000_CTRL);
+
+ hw_dbg("Issuing a global reset to MAC\n");
+ wr32(E1000_CTRL, ctrl | E1000_CTRL_RST);
+
+ ret_val = igb_get_auto_rd_done(hw);
+ if (ret_val) {
+ /* When auto config read does not complete, do not
+ * return with an error. This can happen in situations
+ * where there is no eeprom and prevents getting link.
+ */
+ hw_dbg("Auto Read Done did not complete\n");
+ }
+
+ /* If EEPROM is not present, run manual init scripts */
+ if ((rd32(E1000_EECD) & E1000_EECD_PRES) == 0)
+ igb_reset_init_script_82575(hw);
+
+ /* Clear any pending interrupt events. */
+ wr32(E1000_IMC, 0xffffffff);
+ rd32(E1000_ICR);
+
+ /* Install any alternate MAC address into RAR0 */
+ ret_val = igb_check_alt_mac_addr(hw);
+
+ return ret_val;
+}
+
+/**
+ * igb_init_hw_82575 - Initialize hardware
+ * @hw: pointer to the HW structure
+ *
+ * This inits the hardware readying it for operation.
+ **/
+static s32 igb_init_hw_82575(struct e1000_hw *hw)
+{
+ struct e1000_mac_info *mac = &hw->mac;
+ s32 ret_val;
+ u16 i, rar_count = mac->rar_entry_count;
+
+ if ((hw->mac.type >= e1000_i210) &&
+ !(igb_get_flash_presence_i210(hw))) {
+ ret_val = igb_pll_workaround_i210(hw);
+ if (ret_val)
+ return ret_val;
+ }
+
+ /* Initialize identification LED */
+ ret_val = igb_id_led_init(hw);
+ if (ret_val) {
+ hw_dbg("Error initializing identification LED\n");
+ /* This is not fatal and we should not stop init due to this */
+ }
+
+ /* Disabling VLAN filtering */
+ hw_dbg("Initializing the IEEE VLAN\n");
+ if ((hw->mac.type == e1000_i350) || (hw->mac.type == e1000_i354))
+ igb_clear_vfta_i350(hw);
+ else
+ igb_clear_vfta(hw);
+
+ /* Setup the receive address */
+ igb_init_rx_addrs(hw, rar_count);
+
+ /* Zero out the Multicast HASH table */
+ hw_dbg("Zeroing the MTA\n");
+ for (i = 0; i < mac->mta_reg_count; i++)
+ array_wr32(E1000_MTA, i, 0);
+
+ /* Zero out the Unicast HASH table */
+ hw_dbg("Zeroing the UTA\n");
+ for (i = 0; i < mac->uta_reg_count; i++)
+ array_wr32(E1000_UTA, i, 0);
+
+ /* Setup link and flow control */
+ ret_val = igb_setup_link(hw);
+
+ /* Clear all of the statistics registers (clear on read). It is
+ * important that we do this after we have tried to establish link
+ * because the symbol error count will increment wildly if there
+ * is no link.
+ */
+ igb_clear_hw_cntrs_82575(hw);
+ return ret_val;
+}
+
+/**
+ * igb_setup_copper_link_82575 - Configure copper link settings
+ * @hw: pointer to the HW structure
+ *
+ * Configures the link for auto-neg or forced speed and duplex. Then we check
+ * for link, once link is established calls to configure collision distance
+ * and flow control are called.
+ **/
+static s32 igb_setup_copper_link_82575(struct e1000_hw *hw)
+{
+ u32 ctrl;
+ s32 ret_val;
+ u32 phpm_reg;
+
+ ctrl = rd32(E1000_CTRL);
+ ctrl |= E1000_CTRL_SLU;
+ ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
+ wr32(E1000_CTRL, ctrl);
+
+ /* Clear Go Link Disconnect bit on supported devices */
+ switch (hw->mac.type) {
+ case e1000_82580:
+ case e1000_i350:
+ case e1000_i210:
+ case e1000_i211:
+ phpm_reg = rd32(E1000_82580_PHY_POWER_MGMT);
+ phpm_reg &= ~E1000_82580_PM_GO_LINKD;
+ wr32(E1000_82580_PHY_POWER_MGMT, phpm_reg);
+ break;
+ default:
+ break;
+ }
+
+ ret_val = igb_setup_serdes_link_82575(hw);
+ if (ret_val)
+ goto out;
+
+ if (igb_sgmii_active_82575(hw) && !hw->phy.reset_disable) {
+ /* allow time for SFP cage time to power up phy */
+ msleep(300);
+
+ ret_val = hw->phy.ops.reset(hw);
+ if (ret_val) {
+ hw_dbg("Error resetting the PHY.\n");
+ goto out;
+ }
+ }
+ switch (hw->phy.type) {
+ case e1000_phy_i210:
+ case e1000_phy_m88:
+ switch (hw->phy.id) {
+ case I347AT4_E_PHY_ID:
+ case M88E1112_E_PHY_ID:
+ case M88E1543_E_PHY_ID:
+ case I210_I_PHY_ID:
+ ret_val = igb_copper_link_setup_m88_gen2(hw);
+ break;
+ default:
+ ret_val = igb_copper_link_setup_m88(hw);
+ break;
+ }
+ break;
+ case e1000_phy_igp_3:
+ ret_val = igb_copper_link_setup_igp(hw);
+ break;
+ case e1000_phy_82580:
+ ret_val = igb_copper_link_setup_82580(hw);
+ break;
+ default:
+ ret_val = -E1000_ERR_PHY;
+ break;
+ }
+
+ if (ret_val)
+ goto out;
+
+ ret_val = igb_setup_copper_link(hw);
+out:
+ return ret_val;
+}
+
+/**
+ * igb_setup_serdes_link_82575 - Setup link for serdes
+ * @hw: pointer to the HW structure
+ *
+ * Configure the physical coding sub-layer (PCS) link. The PCS link is
+ * used on copper connections where the serialized gigabit media independent
+ * interface (sgmii), or serdes fiber is being used. Configures the link
+ * for auto-negotiation or forces speed/duplex.
+ **/
+static s32 igb_setup_serdes_link_82575(struct e1000_hw *hw)
+{
+ u32 ctrl_ext, ctrl_reg, reg, anadv_reg;
+ bool pcs_autoneg;
+ s32 ret_val = 0;
+ u16 data;
+
+ if ((hw->phy.media_type != e1000_media_type_internal_serdes) &&
+ !igb_sgmii_active_82575(hw))
+ return ret_val;
+
+
+ /* On the 82575, SerDes loopback mode persists until it is
+ * explicitly turned off or a power cycle is performed. A read to
+ * the register does not indicate its status. Therefore, we ensure
+ * loopback mode is disabled during initialization.
+ */
+ wr32(E1000_SCTL, E1000_SCTL_DISABLE_SERDES_LOOPBACK);
+
+ /* power on the sfp cage if present and turn on I2C */
+ ctrl_ext = rd32(E1000_CTRL_EXT);
+ ctrl_ext &= ~E1000_CTRL_EXT_SDP3_DATA;
+ ctrl_ext |= E1000_CTRL_I2C_ENA;
+ wr32(E1000_CTRL_EXT, ctrl_ext);
+
+ ctrl_reg = rd32(E1000_CTRL);
+ ctrl_reg |= E1000_CTRL_SLU;
+
+ if (hw->mac.type == e1000_82575 || hw->mac.type == e1000_82576) {
+ /* set both sw defined pins */
+ ctrl_reg |= E1000_CTRL_SWDPIN0 | E1000_CTRL_SWDPIN1;
+
+ /* Set switch control to serdes energy detect */
+ reg = rd32(E1000_CONNSW);
+ reg |= E1000_CONNSW_ENRGSRC;
+ wr32(E1000_CONNSW, reg);
+ }
+
+ reg = rd32(E1000_PCS_LCTL);
+
+ /* default pcs_autoneg to the same setting as mac autoneg */
+ pcs_autoneg = hw->mac.autoneg;
+
+ switch (ctrl_ext & E1000_CTRL_EXT_LINK_MODE_MASK) {
+ case E1000_CTRL_EXT_LINK_MODE_SGMII:
+ /* sgmii mode lets the phy handle forcing speed/duplex */
+ pcs_autoneg = true;
+ /* autoneg time out should be disabled for SGMII mode */
+ reg &= ~(E1000_PCS_LCTL_AN_TIMEOUT);
+ break;
+ case E1000_CTRL_EXT_LINK_MODE_1000BASE_KX:
+ /* disable PCS autoneg and support parallel detect only */
+ pcs_autoneg = false;
+ default:
+ if (hw->mac.type == e1000_82575 ||
+ hw->mac.type == e1000_82576) {
+ ret_val = hw->nvm.ops.read(hw, NVM_COMPAT, 1, &data);
+ if (ret_val) {
+ hw_dbg(KERN_DEBUG "NVM Read Error\n\n");
+ return ret_val;
+ }
+
+ if (data & E1000_EEPROM_PCS_AUTONEG_DISABLE_BIT)
+ pcs_autoneg = false;
+ }
+
+ /* non-SGMII modes only supports a speed of 1000/Full for the
+ * link so it is best to just force the MAC and let the pcs
+ * link either autoneg or be forced to 1000/Full
+ */
+ ctrl_reg |= E1000_CTRL_SPD_1000 | E1000_CTRL_FRCSPD |
+ E1000_CTRL_FD | E1000_CTRL_FRCDPX;
+
+ /* set speed of 1000/Full if speed/duplex is forced */
+ reg |= E1000_PCS_LCTL_FSV_1000 | E1000_PCS_LCTL_FDV_FULL;
+ break;
+ }
+
+ wr32(E1000_CTRL, ctrl_reg);
+
+ /* New SerDes mode allows for forcing speed or autonegotiating speed
+ * at 1gb. Autoneg should be default set by most drivers. This is the
+ * mode that will be compatible with older link partners and switches.
+ * However, both are supported by the hardware and some drivers/tools.
+ */
+ reg &= ~(E1000_PCS_LCTL_AN_ENABLE | E1000_PCS_LCTL_FLV_LINK_UP |
+ E1000_PCS_LCTL_FSD | E1000_PCS_LCTL_FORCE_LINK);
+
+ if (pcs_autoneg) {
+ /* Set PCS register for autoneg */
+ reg |= E1000_PCS_LCTL_AN_ENABLE | /* Enable Autoneg */
+ E1000_PCS_LCTL_AN_RESTART; /* Restart autoneg */
+
+ /* Disable force flow control for autoneg */
+ reg &= ~E1000_PCS_LCTL_FORCE_FCTRL;
+
+ /* Configure flow control advertisement for autoneg */
+ anadv_reg = rd32(E1000_PCS_ANADV);
+ anadv_reg &= ~(E1000_TXCW_ASM_DIR | E1000_TXCW_PAUSE);
+ switch (hw->fc.requested_mode) {
+ case e1000_fc_full:
+ case e1000_fc_rx_pause:
+ anadv_reg |= E1000_TXCW_ASM_DIR;
+ anadv_reg |= E1000_TXCW_PAUSE;
+ break;
+ case e1000_fc_tx_pause:
+ anadv_reg |= E1000_TXCW_ASM_DIR;
+ break;
+ default:
+ break;
+ }
+ wr32(E1000_PCS_ANADV, anadv_reg);
+
+ hw_dbg("Configuring Autoneg:PCS_LCTL=0x%08X\n", reg);
+ } else {
+ /* Set PCS register for forced link */
+ reg |= E1000_PCS_LCTL_FSD; /* Force Speed */
+
+ /* Force flow control for forced link */
+ reg |= E1000_PCS_LCTL_FORCE_FCTRL;
+
+ hw_dbg("Configuring Forced Link:PCS_LCTL=0x%08X\n", reg);
+ }
+
+ wr32(E1000_PCS_LCTL, reg);
+
+ if (!pcs_autoneg && !igb_sgmii_active_82575(hw))
+ igb_force_mac_fc(hw);
+
+ return ret_val;
+}
+
+/**
+ * igb_sgmii_active_82575 - Return sgmii state
+ * @hw: pointer to the HW structure
+ *
+ * 82575 silicon has a serialized gigabit media independent interface (sgmii)
+ * which can be enabled for use in the embedded applications. Simply
+ * return the current state of the sgmii interface.
+ **/
+static bool igb_sgmii_active_82575(struct e1000_hw *hw)
+{
+ struct e1000_dev_spec_82575 *dev_spec = &hw->dev_spec._82575;
+ return dev_spec->sgmii_active;
+}
+
+/**
+ * igb_reset_init_script_82575 - Inits HW defaults after reset
+ * @hw: pointer to the HW structure
+ *
+ * Inits recommended HW defaults after a reset when there is no EEPROM
+ * detected. This is only for the 82575.
+ **/
+static s32 igb_reset_init_script_82575(struct e1000_hw *hw)
+{
+ if (hw->mac.type == e1000_82575) {
+ hw_dbg("Running reset init script for 82575\n");
+ /* SerDes configuration via SERDESCTRL */
+ igb_write_8bit_ctrl_reg(hw, E1000_SCTL, 0x00, 0x0C);
+ igb_write_8bit_ctrl_reg(hw, E1000_SCTL, 0x01, 0x78);
+ igb_write_8bit_ctrl_reg(hw, E1000_SCTL, 0x1B, 0x23);
+ igb_write_8bit_ctrl_reg(hw, E1000_SCTL, 0x23, 0x15);
+
+ /* CCM configuration via CCMCTL register */
+ igb_write_8bit_ctrl_reg(hw, E1000_CCMCTL, 0x14, 0x00);
+ igb_write_8bit_ctrl_reg(hw, E1000_CCMCTL, 0x10, 0x00);
+
+ /* PCIe lanes configuration */
+ igb_write_8bit_ctrl_reg(hw, E1000_GIOCTL, 0x00, 0xEC);
+ igb_write_8bit_ctrl_reg(hw, E1000_GIOCTL, 0x61, 0xDF);
+ igb_write_8bit_ctrl_reg(hw, E1000_GIOCTL, 0x34, 0x05);
+ igb_write_8bit_ctrl_reg(hw, E1000_GIOCTL, 0x2F, 0x81);
+
+ /* PCIe PLL Configuration */
+ igb_write_8bit_ctrl_reg(hw, E1000_SCCTL, 0x02, 0x47);
+ igb_write_8bit_ctrl_reg(hw, E1000_SCCTL, 0x14, 0x00);
+ igb_write_8bit_ctrl_reg(hw, E1000_SCCTL, 0x10, 0x00);
+ }
+
+ return 0;
+}
+
+/**
+ * igb_read_mac_addr_82575 - Read device MAC address
+ * @hw: pointer to the HW structure
+ **/
+static s32 igb_read_mac_addr_82575(struct e1000_hw *hw)
+{
+ s32 ret_val = 0;
+
+ /* If there's an alternate MAC address place it in RAR0
+ * so that it will override the Si installed default perm
+ * address.
+ */
+ ret_val = igb_check_alt_mac_addr(hw);
+ if (ret_val)
+ goto out;
+
+ ret_val = igb_read_mac_addr(hw);
+
+out:
+ return ret_val;
+}
+
+/**
+ * igb_power_down_phy_copper_82575 - Remove link during PHY power down
+ * @hw: pointer to the HW structure
+ *
+ * In the case of a PHY power down to save power, or to turn off link during a
+ * driver unload, or wake on lan is not enabled, remove the link.
+ **/
+void igb_power_down_phy_copper_82575(struct e1000_hw *hw)
+{
+ /* If the management interface is not enabled, then power down */
+ if (!(igb_enable_mng_pass_thru(hw) || igb_check_reset_block(hw)))
+ igb_power_down_phy_copper(hw);
+}
+
+/**
+ * igb_clear_hw_cntrs_82575 - Clear device specific hardware counters
+ * @hw: pointer to the HW structure
+ *
+ * Clears the hardware counters by reading the counter registers.
+ **/
+static void igb_clear_hw_cntrs_82575(struct e1000_hw *hw)
+{
+ igb_clear_hw_cntrs_base(hw);
+
+ rd32(E1000_PRC64);
+ rd32(E1000_PRC127);
+ rd32(E1000_PRC255);
+ rd32(E1000_PRC511);
+ rd32(E1000_PRC1023);
+ rd32(E1000_PRC1522);
+ rd32(E1000_PTC64);
+ rd32(E1000_PTC127);
+ rd32(E1000_PTC255);
+ rd32(E1000_PTC511);
+ rd32(E1000_PTC1023);
+ rd32(E1000_PTC1522);
+
+ rd32(E1000_ALGNERRC);
+ rd32(E1000_RXERRC);
+ rd32(E1000_TNCRS);
+ rd32(E1000_CEXTERR);
+ rd32(E1000_TSCTC);
+ rd32(E1000_TSCTFC);
+
+ rd32(E1000_MGTPRC);
+ rd32(E1000_MGTPDC);
+ rd32(E1000_MGTPTC);
+
+ rd32(E1000_IAC);
+ rd32(E1000_ICRXOC);
+
+ rd32(E1000_ICRXPTC);
+ rd32(E1000_ICRXATC);
+ rd32(E1000_ICTXPTC);
+ rd32(E1000_ICTXATC);
+ rd32(E1000_ICTXQEC);
+ rd32(E1000_ICTXQMTC);
+ rd32(E1000_ICRXDMTC);
+
+ rd32(E1000_CBTMPC);
+ rd32(E1000_HTDPMC);
+ rd32(E1000_CBRMPC);
+ rd32(E1000_RPTHC);
+ rd32(E1000_HGPTC);
+ rd32(E1000_HTCBDPC);
+ rd32(E1000_HGORCL);
+ rd32(E1000_HGORCH);
+ rd32(E1000_HGOTCL);
+ rd32(E1000_HGOTCH);
+ rd32(E1000_LENERRS);
+
+ /* This register should not be read in copper configurations */
+ if (hw->phy.media_type == e1000_media_type_internal_serdes ||
+ igb_sgmii_active_82575(hw))
+ rd32(E1000_SCVPC);
+}
+
+/**
+ * igb_rx_fifo_flush_82575 - Clean rx fifo after RX enable
+ * @hw: pointer to the HW structure
+ *
+ * After rx enable if managability is enabled then there is likely some
+ * bad data at the start of the fifo and possibly in the DMA fifo. This
+ * function clears the fifos and flushes any packets that came in as rx was
+ * being enabled.
+ **/
+void igb_rx_fifo_flush_82575(struct e1000_hw *hw)
+{
+ u32 rctl, rlpml, rxdctl[4], rfctl, temp_rctl, rx_enabled;
+ int i, ms_wait;
+
+ if (hw->mac.type != e1000_82575 ||
+ !(rd32(E1000_MANC) & E1000_MANC_RCV_TCO_EN))
+ return;
+
+ /* Disable all RX queues */
+ for (i = 0; i < 4; i++) {
+ rxdctl[i] = rd32(E1000_RXDCTL(i));
+ wr32(E1000_RXDCTL(i),
+ rxdctl[i] & ~E1000_RXDCTL_QUEUE_ENABLE);
+ }
+ /* Poll all queues to verify they have shut down */
+ for (ms_wait = 0; ms_wait < 10; ms_wait++) {
+ usleep_range(1000, 2000);
+ rx_enabled = 0;
+ for (i = 0; i < 4; i++)
+ rx_enabled |= rd32(E1000_RXDCTL(i));
+ if (!(rx_enabled & E1000_RXDCTL_QUEUE_ENABLE))
+ break;
+ }
+
+ if (ms_wait == 10)
+ hw_dbg("Queue disable timed out after 10ms\n");
+
+ /* Clear RLPML, RCTL.SBP, RFCTL.LEF, and set RCTL.LPE so that all
+ * incoming packets are rejected. Set enable and wait 2ms so that
+ * any packet that was coming in as RCTL.EN was set is flushed
+ */
+ rfctl = rd32(E1000_RFCTL);
+ wr32(E1000_RFCTL, rfctl & ~E1000_RFCTL_LEF);
+
+ rlpml = rd32(E1000_RLPML);
+ wr32(E1000_RLPML, 0);
+
+ rctl = rd32(E1000_RCTL);
+ temp_rctl = rctl & ~(E1000_RCTL_EN | E1000_RCTL_SBP);
+ temp_rctl |= E1000_RCTL_LPE;
+
+ wr32(E1000_RCTL, temp_rctl);
+ wr32(E1000_RCTL, temp_rctl | E1000_RCTL_EN);
+ wrfl();
+ usleep_range(2000, 3000);
+
+ /* Enable RX queues that were previously enabled and restore our
+ * previous state
+ */
+ for (i = 0; i < 4; i++)
+ wr32(E1000_RXDCTL(i), rxdctl[i]);
+ wr32(E1000_RCTL, rctl);
+ wrfl();
+
+ wr32(E1000_RLPML, rlpml);
+ wr32(E1000_RFCTL, rfctl);
+
+ /* Flush receive errors generated by workaround */
+ rd32(E1000_ROC);
+ rd32(E1000_RNBC);
+ rd32(E1000_MPC);
+}
+
+/**
+ * igb_set_pcie_completion_timeout - set pci-e completion timeout
+ * @hw: pointer to the HW structure
+ *
+ * The defaults for 82575 and 82576 should be in the range of 50us to 50ms,
+ * however the hardware default for these parts is 500us to 1ms which is less
+ * than the 10ms recommended by the pci-e spec. To address this we need to
+ * increase the value to either 10ms to 200ms for capability version 1 config,
+ * or 16ms to 55ms for version 2.
+ **/
+static s32 igb_set_pcie_completion_timeout(struct e1000_hw *hw)
+{
+ u32 gcr = rd32(E1000_GCR);
+ s32 ret_val = 0;
+ u16 pcie_devctl2;
+
+ /* only take action if timeout value is defaulted to 0 */
+ if (gcr & E1000_GCR_CMPL_TMOUT_MASK)
+ goto out;
+
+ /* if capabilities version is type 1 we can write the
+ * timeout of 10ms to 200ms through the GCR register
+ */
+ if (!(gcr & E1000_GCR_CAP_VER2)) {
+ gcr |= E1000_GCR_CMPL_TMOUT_10ms;
+ goto out;
+ }
+
+ /* for version 2 capabilities we need to write the config space
+ * directly in order to set the completion timeout value for
+ * 16ms to 55ms
+ */
+ ret_val = igb_read_pcie_cap_reg(hw, PCIE_DEVICE_CONTROL2,
+ &pcie_devctl2);
+ if (ret_val)
+ goto out;
+
+ pcie_devctl2 |= PCIE_DEVICE_CONTROL2_16ms;
+
+ ret_val = igb_write_pcie_cap_reg(hw, PCIE_DEVICE_CONTROL2,
+ &pcie_devctl2);
+out:
+ /* disable completion timeout resend */
+ gcr &= ~E1000_GCR_CMPL_TMOUT_RESEND;
+
+ wr32(E1000_GCR, gcr);
+ return ret_val;
+}
+
+/**
+ * igb_vmdq_set_anti_spoofing_pf - enable or disable anti-spoofing
+ * @hw: pointer to the hardware struct
+ * @enable: state to enter, either enabled or disabled
+ * @pf: Physical Function pool - do not set anti-spoofing for the PF
+ *
+ * enables/disables L2 switch anti-spoofing functionality.
+ **/
+void igb_vmdq_set_anti_spoofing_pf(struct e1000_hw *hw, bool enable, int pf)
+{
+ u32 reg_val, reg_offset;
+
+ switch (hw->mac.type) {
+ case e1000_82576:
+ reg_offset = E1000_DTXSWC;
+ break;
+ case e1000_i350:
+ case e1000_i354:
+ reg_offset = E1000_TXSWC;
+ break;
+ default:
+ return;
+ }
+
+ reg_val = rd32(reg_offset);
+ if (enable) {
+ reg_val |= (E1000_DTXSWC_MAC_SPOOF_MASK |
+ E1000_DTXSWC_VLAN_SPOOF_MASK);
+ /* The PF can spoof - it has to in order to
+ * support emulation mode NICs
+ */
+ reg_val ^= (1 << pf | 1 << (pf + MAX_NUM_VFS));
+ } else {
+ reg_val &= ~(E1000_DTXSWC_MAC_SPOOF_MASK |
+ E1000_DTXSWC_VLAN_SPOOF_MASK);
+ }
+ wr32(reg_offset, reg_val);
+}
+
+/**
+ * igb_vmdq_set_loopback_pf - enable or disable vmdq loopback
+ * @hw: pointer to the hardware struct
+ * @enable: state to enter, either enabled or disabled
+ *
+ * enables/disables L2 switch loopback functionality.
+ **/
+void igb_vmdq_set_loopback_pf(struct e1000_hw *hw, bool enable)
+{
+ u32 dtxswc;
+
+ switch (hw->mac.type) {
+ case e1000_82576:
+ dtxswc = rd32(E1000_DTXSWC);
+ if (enable)
+ dtxswc |= E1000_DTXSWC_VMDQ_LOOPBACK_EN;
+ else
+ dtxswc &= ~E1000_DTXSWC_VMDQ_LOOPBACK_EN;
+ wr32(E1000_DTXSWC, dtxswc);
+ break;
+ case e1000_i354:
+ case e1000_i350:
+ dtxswc = rd32(E1000_TXSWC);
+ if (enable)
+ dtxswc |= E1000_DTXSWC_VMDQ_LOOPBACK_EN;
+ else
+ dtxswc &= ~E1000_DTXSWC_VMDQ_LOOPBACK_EN;
+ wr32(E1000_TXSWC, dtxswc);
+ break;
+ default:
+ /* Currently no other hardware supports loopback */
+ break;
+ }
+
+}
+
+/**
+ * igb_vmdq_set_replication_pf - enable or disable vmdq replication
+ * @hw: pointer to the hardware struct
+ * @enable: state to enter, either enabled or disabled
+ *
+ * enables/disables replication of packets across multiple pools.
+ **/
+void igb_vmdq_set_replication_pf(struct e1000_hw *hw, bool enable)
+{
+ u32 vt_ctl = rd32(E1000_VT_CTL);
+
+ if (enable)
+ vt_ctl |= E1000_VT_CTL_VM_REPL_EN;
+ else
+ vt_ctl &= ~E1000_VT_CTL_VM_REPL_EN;
+
+ wr32(E1000_VT_CTL, vt_ctl);
+}
+
+/**
+ * igb_read_phy_reg_82580 - Read 82580 MDI control register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to be read
+ * @data: pointer to the read data
+ *
+ * Reads the MDI control register in the PHY at offset and stores the
+ * information read to data.
+ **/
+static s32 igb_read_phy_reg_82580(struct e1000_hw *hw, u32 offset, u16 *data)
+{
+ s32 ret_val;
+
+ ret_val = hw->phy.ops.acquire(hw);
+ if (ret_val)
+ goto out;
+
+ ret_val = igb_read_phy_reg_mdic(hw, offset, data);
+
+ hw->phy.ops.release(hw);
+
+out:
+ return ret_val;
+}
+
+/**
+ * igb_write_phy_reg_82580 - Write 82580 MDI control register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to write to
+ * @data: data to write to register at offset
+ *
+ * Writes data to MDI control register in the PHY at offset.
+ **/
+static s32 igb_write_phy_reg_82580(struct e1000_hw *hw, u32 offset, u16 data)
+{
+ s32 ret_val;
+
+
+ ret_val = hw->phy.ops.acquire(hw);
+ if (ret_val)
+ goto out;
+
+ ret_val = igb_write_phy_reg_mdic(hw, offset, data);
+
+ hw->phy.ops.release(hw);
+
+out:
+ return ret_val;
+}
+
+/**
+ * igb_reset_mdicnfg_82580 - Reset MDICNFG destination and com_mdio bits
+ * @hw: pointer to the HW structure
+ *
+ * This resets the the MDICNFG.Destination and MDICNFG.Com_MDIO bits based on
+ * the values found in the EEPROM. This addresses an issue in which these
+ * bits are not restored from EEPROM after reset.
+ **/
+static s32 igb_reset_mdicnfg_82580(struct e1000_hw *hw)
+{
+ s32 ret_val = 0;
+ u32 mdicnfg;
+ u16 nvm_data = 0;
+
+ if (hw->mac.type != e1000_82580)
+ goto out;
+ if (!igb_sgmii_active_82575(hw))
+ goto out;
+
+ ret_val = hw->nvm.ops.read(hw, NVM_INIT_CONTROL3_PORT_A +
+ NVM_82580_LAN_FUNC_OFFSET(hw->bus.func), 1,
+ &nvm_data);
+ if (ret_val) {
+ hw_dbg("NVM Read Error\n");
+ goto out;
+ }
+
+ mdicnfg = rd32(E1000_MDICNFG);
+ if (nvm_data & NVM_WORD24_EXT_MDIO)
+ mdicnfg |= E1000_MDICNFG_EXT_MDIO;
+ if (nvm_data & NVM_WORD24_COM_MDIO)
+ mdicnfg |= E1000_MDICNFG_COM_MDIO;
+ wr32(E1000_MDICNFG, mdicnfg);
+out:
+ return ret_val;
+}
+
+/**
+ * igb_reset_hw_82580 - Reset hardware
+ * @hw: pointer to the HW structure
+ *
+ * This resets function or entire device (all ports, etc.)
+ * to a known state.
+ **/
+static s32 igb_reset_hw_82580(struct e1000_hw *hw)
+{
+ s32 ret_val = 0;
+ /* BH SW mailbox bit in SW_FW_SYNC */
+ u16 swmbsw_mask = E1000_SW_SYNCH_MB;
+ u32 ctrl;
+ bool global_device_reset = hw->dev_spec._82575.global_device_reset;
+
+ hw->dev_spec._82575.global_device_reset = false;
+
+ /* due to hw errata, global device reset doesn't always
+ * work on 82580
+ */
+ if (hw->mac.type == e1000_82580)
+ global_device_reset = false;
+
+ /* Get current control state. */
+ ctrl = rd32(E1000_CTRL);
+
+ /* Prevent the PCI-E bus from sticking if there is no TLP connection
+ * on the last TLP read/write transaction when MAC is reset.
+ */
+ ret_val = igb_disable_pcie_master(hw);
+ if (ret_val)
+ hw_dbg("PCI-E Master disable polling has failed.\n");
+
+ hw_dbg("Masking off all interrupts\n");
+ wr32(E1000_IMC, 0xffffffff);
+ wr32(E1000_RCTL, 0);
+ wr32(E1000_TCTL, E1000_TCTL_PSP);
+ wrfl();
+
+ usleep_range(10000, 11000);
+
+ /* Determine whether or not a global dev reset is requested */
+ if (global_device_reset &&
+ hw->mac.ops.acquire_swfw_sync(hw, swmbsw_mask))
+ global_device_reset = false;
+
+ if (global_device_reset &&
+ !(rd32(E1000_STATUS) & E1000_STAT_DEV_RST_SET))
+ ctrl |= E1000_CTRL_DEV_RST;
+ else
+ ctrl |= E1000_CTRL_RST;
+
+ wr32(E1000_CTRL, ctrl);
+ wrfl();
+
+ /* Add delay to insure DEV_RST has time to complete */
+ if (global_device_reset)
+ usleep_range(5000, 6000);
+
+ ret_val = igb_get_auto_rd_done(hw);
+ if (ret_val) {
+ /* When auto config read does not complete, do not
+ * return with an error. This can happen in situations
+ * where there is no eeprom and prevents getting link.
+ */
+ hw_dbg("Auto Read Done did not complete\n");
+ }
+
+ /* clear global device reset status bit */
+ wr32(E1000_STATUS, E1000_STAT_DEV_RST_SET);
+
+ /* Clear any pending interrupt events. */
+ wr32(E1000_IMC, 0xffffffff);
+ rd32(E1000_ICR);
+
+ ret_val = igb_reset_mdicnfg_82580(hw);
+ if (ret_val)
+ hw_dbg("Could not reset MDICNFG based on EEPROM\n");
+
+ /* Install any alternate MAC address into RAR0 */
+ ret_val = igb_check_alt_mac_addr(hw);
+
+ /* Release semaphore */
+ if (global_device_reset)
+ hw->mac.ops.release_swfw_sync(hw, swmbsw_mask);
+
+ return ret_val;
+}
+
+/**
+ * igb_rxpbs_adjust_82580 - adjust RXPBS value to reflect actual RX PBA size
+ * @data: data received by reading RXPBS register
+ *
+ * The 82580 uses a table based approach for packet buffer allocation sizes.
+ * This function converts the retrieved value into the correct table value
+ * 0x0 0x1 0x2 0x3 0x4 0x5 0x6 0x7
+ * 0x0 36 72 144 1 2 4 8 16
+ * 0x8 35 70 140 rsv rsv rsv rsv rsv
+ */
+u16 igb_rxpbs_adjust_82580(u32 data)
+{
+ u16 ret_val = 0;
+
+ if (data < ARRAY_SIZE(e1000_82580_rxpbs_table))
+ ret_val = e1000_82580_rxpbs_table[data];
+
+ return ret_val;
+}
+
+/**
+ * igb_validate_nvm_checksum_with_offset - Validate EEPROM
+ * checksum
+ * @hw: pointer to the HW structure
+ * @offset: offset in words of the checksum protected region
+ *
+ * Calculates the EEPROM checksum by reading/adding each word of the EEPROM
+ * and then verifies that the sum of the EEPROM is equal to 0xBABA.
+ **/
+static s32 igb_validate_nvm_checksum_with_offset(struct e1000_hw *hw,
+ u16 offset)
+{
+ s32 ret_val = 0;
+ u16 checksum = 0;
+ u16 i, nvm_data;
+
+ for (i = offset; i < ((NVM_CHECKSUM_REG + offset) + 1); i++) {
+ ret_val = hw->nvm.ops.read(hw, i, 1, &nvm_data);
+ if (ret_val) {
+ hw_dbg("NVM Read Error\n");
+ goto out;
+ }
+ checksum += nvm_data;
+ }
+
+ if (checksum != (u16) NVM_SUM) {
+ hw_dbg("NVM Checksum Invalid\n");
+ ret_val = -E1000_ERR_NVM;
+ goto out;
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * igb_update_nvm_checksum_with_offset - Update EEPROM
+ * checksum
+ * @hw: pointer to the HW structure
+ * @offset: offset in words of the checksum protected region
+ *
+ * Updates the EEPROM checksum by reading/adding each word of the EEPROM
+ * up to the checksum. Then calculates the EEPROM checksum and writes the
+ * value to the EEPROM.
+ **/
+static s32 igb_update_nvm_checksum_with_offset(struct e1000_hw *hw, u16 offset)
+{
+ s32 ret_val;
+ u16 checksum = 0;
+ u16 i, nvm_data;
+
+ for (i = offset; i < (NVM_CHECKSUM_REG + offset); i++) {
+ ret_val = hw->nvm.ops.read(hw, i, 1, &nvm_data);
+ if (ret_val) {
+ hw_dbg("NVM Read Error while updating checksum.\n");
+ goto out;
+ }
+ checksum += nvm_data;
+ }
+ checksum = (u16) NVM_SUM - checksum;
+ ret_val = hw->nvm.ops.write(hw, (NVM_CHECKSUM_REG + offset), 1,
+ &checksum);
+ if (ret_val)
+ hw_dbg("NVM Write Error while updating checksum.\n");
+
+out:
+ return ret_val;
+}
+
+/**
+ * igb_validate_nvm_checksum_82580 - Validate EEPROM checksum
+ * @hw: pointer to the HW structure
+ *
+ * Calculates the EEPROM section checksum by reading/adding each word of
+ * the EEPROM and then verifies that the sum of the EEPROM is
+ * equal to 0xBABA.
+ **/
+static s32 igb_validate_nvm_checksum_82580(struct e1000_hw *hw)
+{
+ s32 ret_val = 0;
+ u16 eeprom_regions_count = 1;
+ u16 j, nvm_data;
+ u16 nvm_offset;
+
+ ret_val = hw->nvm.ops.read(hw, NVM_COMPATIBILITY_REG_3, 1, &nvm_data);
+ if (ret_val) {
+ hw_dbg("NVM Read Error\n");
+ goto out;
+ }
+
+ if (nvm_data & NVM_COMPATIBILITY_BIT_MASK) {
+ /* if checksums compatibility bit is set validate checksums
+ * for all 4 ports.
+ */
+ eeprom_regions_count = 4;
+ }
+
+ for (j = 0; j < eeprom_regions_count; j++) {
+ nvm_offset = NVM_82580_LAN_FUNC_OFFSET(j);
+ ret_val = igb_validate_nvm_checksum_with_offset(hw,
+ nvm_offset);
+ if (ret_val != 0)
+ goto out;
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * igb_update_nvm_checksum_82580 - Update EEPROM checksum
+ * @hw: pointer to the HW structure
+ *
+ * Updates the EEPROM section checksums for all 4 ports by reading/adding
+ * each word of the EEPROM up to the checksum. Then calculates the EEPROM
+ * checksum and writes the value to the EEPROM.
+ **/
+static s32 igb_update_nvm_checksum_82580(struct e1000_hw *hw)
+{
+ s32 ret_val;
+ u16 j, nvm_data;
+ u16 nvm_offset;
+
+ ret_val = hw->nvm.ops.read(hw, NVM_COMPATIBILITY_REG_3, 1, &nvm_data);
+ if (ret_val) {
+ hw_dbg("NVM Read Error while updating checksum compatibility bit.\n");
+ goto out;
+ }
+
+ if ((nvm_data & NVM_COMPATIBILITY_BIT_MASK) == 0) {
+ /* set compatibility bit to validate checksums appropriately */
+ nvm_data = nvm_data | NVM_COMPATIBILITY_BIT_MASK;
+ ret_val = hw->nvm.ops.write(hw, NVM_COMPATIBILITY_REG_3, 1,
+ &nvm_data);
+ if (ret_val) {
+ hw_dbg("NVM Write Error while updating checksum compatibility bit.\n");
+ goto out;
+ }
+ }
+
+ for (j = 0; j < 4; j++) {
+ nvm_offset = NVM_82580_LAN_FUNC_OFFSET(j);
+ ret_val = igb_update_nvm_checksum_with_offset(hw, nvm_offset);
+ if (ret_val)
+ goto out;
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * igb_validate_nvm_checksum_i350 - Validate EEPROM checksum
+ * @hw: pointer to the HW structure
+ *
+ * Calculates the EEPROM section checksum by reading/adding each word of
+ * the EEPROM and then verifies that the sum of the EEPROM is
+ * equal to 0xBABA.
+ **/
+static s32 igb_validate_nvm_checksum_i350(struct e1000_hw *hw)
+{
+ s32 ret_val = 0;
+ u16 j;
+ u16 nvm_offset;
+
+ for (j = 0; j < 4; j++) {
+ nvm_offset = NVM_82580_LAN_FUNC_OFFSET(j);
+ ret_val = igb_validate_nvm_checksum_with_offset(hw,
+ nvm_offset);
+ if (ret_val != 0)
+ goto out;
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * igb_update_nvm_checksum_i350 - Update EEPROM checksum
+ * @hw: pointer to the HW structure
+ *
+ * Updates the EEPROM section checksums for all 4 ports by reading/adding
+ * each word of the EEPROM up to the checksum. Then calculates the EEPROM
+ * checksum and writes the value to the EEPROM.
+ **/
+static s32 igb_update_nvm_checksum_i350(struct e1000_hw *hw)
+{
+ s32 ret_val = 0;
+ u16 j;
+ u16 nvm_offset;
+
+ for (j = 0; j < 4; j++) {
+ nvm_offset = NVM_82580_LAN_FUNC_OFFSET(j);
+ ret_val = igb_update_nvm_checksum_with_offset(hw, nvm_offset);
+ if (ret_val != 0)
+ goto out;
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * __igb_access_emi_reg - Read/write EMI register
+ * @hw: pointer to the HW structure
+ * @addr: EMI address to program
+ * @data: pointer to value to read/write from/to the EMI address
+ * @read: boolean flag to indicate read or write
+ **/
+static s32 __igb_access_emi_reg(struct e1000_hw *hw, u16 address,
+ u16 *data, bool read)
+{
+ s32 ret_val = 0;
+
+ ret_val = hw->phy.ops.write_reg(hw, E1000_EMIADD, address);
+ if (ret_val)
+ return ret_val;
+
+ if (read)
+ ret_val = hw->phy.ops.read_reg(hw, E1000_EMIDATA, data);
+ else
+ ret_val = hw->phy.ops.write_reg(hw, E1000_EMIDATA, *data);
+
+ return ret_val;
+}
+
+/**
+ * igb_read_emi_reg - Read Extended Management Interface register
+ * @hw: pointer to the HW structure
+ * @addr: EMI address to program
+ * @data: value to be read from the EMI address
+ **/
+s32 igb_read_emi_reg(struct e1000_hw *hw, u16 addr, u16 *data)
+{
+ return __igb_access_emi_reg(hw, addr, data, true);
+}
+
+/**
+ * igb_set_eee_i350 - Enable/disable EEE support
+ * @hw: pointer to the HW structure
+ * @adv1G: boolean flag enabling 1G EEE advertisement
+ * @adv100m: boolean flag enabling 100M EEE advertisement
+ *
+ * Enable/disable EEE based on setting in dev_spec structure.
+ *
+ **/
+s32 igb_set_eee_i350(struct e1000_hw *hw, bool adv1G, bool adv100M)
+{
+ u32 ipcnfg, eeer;
+
+ if ((hw->mac.type < e1000_i350) ||
+ (hw->phy.media_type != e1000_media_type_copper))
+ goto out;
+ ipcnfg = rd32(E1000_IPCNFG);
+ eeer = rd32(E1000_EEER);
+
+ /* enable or disable per user setting */
+ if (!(hw->dev_spec._82575.eee_disable)) {
+ u32 eee_su = rd32(E1000_EEE_SU);
+
+ if (adv100M)
+ ipcnfg |= E1000_IPCNFG_EEE_100M_AN;
+ else
+ ipcnfg &= ~E1000_IPCNFG_EEE_100M_AN;
+
+ if (adv1G)
+ ipcnfg |= E1000_IPCNFG_EEE_1G_AN;
+ else
+ ipcnfg &= ~E1000_IPCNFG_EEE_1G_AN;
+
+ eeer |= (E1000_EEER_TX_LPI_EN | E1000_EEER_RX_LPI_EN |
+ E1000_EEER_LPI_FC);
+
+ /* This bit should not be set in normal operation. */
+ if (eee_su & E1000_EEE_SU_LPI_CLK_STP)
+ hw_dbg("LPI Clock Stop Bit should not be set!\n");
+
+ } else {
+ ipcnfg &= ~(E1000_IPCNFG_EEE_1G_AN |
+ E1000_IPCNFG_EEE_100M_AN);
+ eeer &= ~(E1000_EEER_TX_LPI_EN |
+ E1000_EEER_RX_LPI_EN |
+ E1000_EEER_LPI_FC);
+ }
+ wr32(E1000_IPCNFG, ipcnfg);
+ wr32(E1000_EEER, eeer);
+ rd32(E1000_IPCNFG);
+ rd32(E1000_EEER);
+out:
+
+ return 0;
+}
+
+/**
+ * igb_set_eee_i354 - Enable/disable EEE support
+ * @hw: pointer to the HW structure
+ * @adv1G: boolean flag enabling 1G EEE advertisement
+ * @adv100m: boolean flag enabling 100M EEE advertisement
+ *
+ * Enable/disable EEE legacy mode based on setting in dev_spec structure.
+ *
+ **/
+s32 igb_set_eee_i354(struct e1000_hw *hw, bool adv1G, bool adv100M)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val = 0;
+ u16 phy_data;
+
+ if ((hw->phy.media_type != e1000_media_type_copper) ||
+ (phy->id != M88E1543_E_PHY_ID))
+ goto out;
+
+ if (!hw->dev_spec._82575.eee_disable) {
+ /* Switch to PHY page 18. */
+ ret_val = phy->ops.write_reg(hw, E1000_M88E1543_PAGE_ADDR, 18);
+ if (ret_val)
+ goto out;
+
+ ret_val = phy->ops.read_reg(hw, E1000_M88E1543_EEE_CTRL_1,
+ &phy_data);
+ if (ret_val)
+ goto out;
+
+ phy_data |= E1000_M88E1543_EEE_CTRL_1_MS;
+ ret_val = phy->ops.write_reg(hw, E1000_M88E1543_EEE_CTRL_1,
+ phy_data);
+ if (ret_val)
+ goto out;
+
+ /* Return the PHY to page 0. */
+ ret_val = phy->ops.write_reg(hw, E1000_M88E1543_PAGE_ADDR, 0);
+ if (ret_val)
+ goto out;
+
+ /* Turn on EEE advertisement. */
+ ret_val = igb_read_xmdio_reg(hw, E1000_EEE_ADV_ADDR_I354,
+ E1000_EEE_ADV_DEV_I354,
+ &phy_data);
+ if (ret_val)
+ goto out;
+
+ if (adv100M)
+ phy_data |= E1000_EEE_ADV_100_SUPPORTED;
+ else
+ phy_data &= ~E1000_EEE_ADV_100_SUPPORTED;
+
+ if (adv1G)
+ phy_data |= E1000_EEE_ADV_1000_SUPPORTED;
+ else
+ phy_data &= ~E1000_EEE_ADV_1000_SUPPORTED;
+
+ ret_val = igb_write_xmdio_reg(hw, E1000_EEE_ADV_ADDR_I354,
+ E1000_EEE_ADV_DEV_I354,
+ phy_data);
+ } else {
+ /* Turn off EEE advertisement. */
+ ret_val = igb_read_xmdio_reg(hw, E1000_EEE_ADV_ADDR_I354,
+ E1000_EEE_ADV_DEV_I354,
+ &phy_data);
+ if (ret_val)
+ goto out;
+
+ phy_data &= ~(E1000_EEE_ADV_100_SUPPORTED |
+ E1000_EEE_ADV_1000_SUPPORTED);
+ ret_val = igb_write_xmdio_reg(hw, E1000_EEE_ADV_ADDR_I354,
+ E1000_EEE_ADV_DEV_I354,
+ phy_data);
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * igb_get_eee_status_i354 - Get EEE status
+ * @hw: pointer to the HW structure
+ * @status: EEE status
+ *
+ * Get EEE status by guessing based on whether Tx or Rx LPI indications have
+ * been received.
+ **/
+s32 igb_get_eee_status_i354(struct e1000_hw *hw, bool *status)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ s32 ret_val = 0;
+ u16 phy_data;
+
+ /* Check if EEE is supported on this device. */
+ if ((hw->phy.media_type != e1000_media_type_copper) ||
+ (phy->id != M88E1543_E_PHY_ID))
+ goto out;
+
+ ret_val = igb_read_xmdio_reg(hw, E1000_PCS_STATUS_ADDR_I354,
+ E1000_PCS_STATUS_DEV_I354,
+ &phy_data);
+ if (ret_val)
+ goto out;
+
+ *status = phy_data & (E1000_PCS_STATUS_TX_LPI_RCVD |
+ E1000_PCS_STATUS_RX_LPI_RCVD) ? true : false;
+
+out:
+ return ret_val;
+}
+
+static const u8 e1000_emc_temp_data[4] = {
+ E1000_EMC_INTERNAL_DATA,
+ E1000_EMC_DIODE1_DATA,
+ E1000_EMC_DIODE2_DATA,
+ E1000_EMC_DIODE3_DATA
+};
+static const u8 e1000_emc_therm_limit[4] = {
+ E1000_EMC_INTERNAL_THERM_LIMIT,
+ E1000_EMC_DIODE1_THERM_LIMIT,
+ E1000_EMC_DIODE2_THERM_LIMIT,
+ E1000_EMC_DIODE3_THERM_LIMIT
+};
+
+#ifdef CONFIG_IGB_HWMON
+/**
+ * igb_get_thermal_sensor_data_generic - Gathers thermal sensor data
+ * @hw: pointer to hardware structure
+ *
+ * Updates the temperatures in mac.thermal_sensor_data
+ **/
+static s32 igb_get_thermal_sensor_data_generic(struct e1000_hw *hw)
+{
+ u16 ets_offset;
+ u16 ets_cfg;
+ u16 ets_sensor;
+ u8 num_sensors;
+ u8 sensor_index;
+ u8 sensor_location;
+ u8 i;
+ struct e1000_thermal_sensor_data *data = &hw->mac.thermal_sensor_data;
+
+ if ((hw->mac.type != e1000_i350) || (hw->bus.func != 0))
+ return E1000_NOT_IMPLEMENTED;
+
+ data->sensor[0].temp = (rd32(E1000_THMJT) & 0xFF);
+
+ /* Return the internal sensor only if ETS is unsupported */
+ hw->nvm.ops.read(hw, NVM_ETS_CFG, 1, &ets_offset);
+ if ((ets_offset == 0x0000) || (ets_offset == 0xFFFF))
+ return 0;
+
+ hw->nvm.ops.read(hw, ets_offset, 1, &ets_cfg);
+ if (((ets_cfg & NVM_ETS_TYPE_MASK) >> NVM_ETS_TYPE_SHIFT)
+ != NVM_ETS_TYPE_EMC)
+ return E1000_NOT_IMPLEMENTED;
+
+ num_sensors = (ets_cfg & NVM_ETS_NUM_SENSORS_MASK);
+ if (num_sensors > E1000_MAX_SENSORS)
+ num_sensors = E1000_MAX_SENSORS;
+
+ for (i = 1; i < num_sensors; i++) {
+ hw->nvm.ops.read(hw, (ets_offset + i), 1, &ets_sensor);
+ sensor_index = ((ets_sensor & NVM_ETS_DATA_INDEX_MASK) >>
+ NVM_ETS_DATA_INDEX_SHIFT);
+ sensor_location = ((ets_sensor & NVM_ETS_DATA_LOC_MASK) >>
+ NVM_ETS_DATA_LOC_SHIFT);
+
+ if (sensor_location != 0)
+ hw->phy.ops.read_i2c_byte(hw,
+ e1000_emc_temp_data[sensor_index],
+ E1000_I2C_THERMAL_SENSOR_ADDR,
+ &data->sensor[i].temp);
+ }
+ return 0;
+}
+
+/**
+ * igb_init_thermal_sensor_thresh_generic - Sets thermal sensor thresholds
+ * @hw: pointer to hardware structure
+ *
+ * Sets the thermal sensor thresholds according to the NVM map
+ * and save off the threshold and location values into mac.thermal_sensor_data
+ **/
+static s32 igb_init_thermal_sensor_thresh_generic(struct e1000_hw *hw)
+{
+ u16 ets_offset;
+ u16 ets_cfg;
+ u16 ets_sensor;
+ u8 low_thresh_delta;
+ u8 num_sensors;
+ u8 sensor_index;
+ u8 sensor_location;
+ u8 therm_limit;
+ u8 i;
+ struct e1000_thermal_sensor_data *data = &hw->mac.thermal_sensor_data;
+
+ if ((hw->mac.type != e1000_i350) || (hw->bus.func != 0))
+ return E1000_NOT_IMPLEMENTED;
+
+ memset(data, 0, sizeof(struct e1000_thermal_sensor_data));
+
+ data->sensor[0].location = 0x1;
+ data->sensor[0].caution_thresh =
+ (rd32(E1000_THHIGHTC) & 0xFF);
+ data->sensor[0].max_op_thresh =
+ (rd32(E1000_THLOWTC) & 0xFF);
+
+ /* Return the internal sensor only if ETS is unsupported */
+ hw->nvm.ops.read(hw, NVM_ETS_CFG, 1, &ets_offset);
+ if ((ets_offset == 0x0000) || (ets_offset == 0xFFFF))
+ return 0;
+
+ hw->nvm.ops.read(hw, ets_offset, 1, &ets_cfg);
+ if (((ets_cfg & NVM_ETS_TYPE_MASK) >> NVM_ETS_TYPE_SHIFT)
+ != NVM_ETS_TYPE_EMC)
+ return E1000_NOT_IMPLEMENTED;
+
+ low_thresh_delta = ((ets_cfg & NVM_ETS_LTHRES_DELTA_MASK) >>
+ NVM_ETS_LTHRES_DELTA_SHIFT);
+ num_sensors = (ets_cfg & NVM_ETS_NUM_SENSORS_MASK);
+
+ for (i = 1; i <= num_sensors; i++) {
+ hw->nvm.ops.read(hw, (ets_offset + i), 1, &ets_sensor);
+ sensor_index = ((ets_sensor & NVM_ETS_DATA_INDEX_MASK) >>
+ NVM_ETS_DATA_INDEX_SHIFT);
+ sensor_location = ((ets_sensor & NVM_ETS_DATA_LOC_MASK) >>
+ NVM_ETS_DATA_LOC_SHIFT);
+ therm_limit = ets_sensor & NVM_ETS_DATA_HTHRESH_MASK;
+
+ hw->phy.ops.write_i2c_byte(hw,
+ e1000_emc_therm_limit[sensor_index],
+ E1000_I2C_THERMAL_SENSOR_ADDR,
+ therm_limit);
+
+ if ((i < E1000_MAX_SENSORS) && (sensor_location != 0)) {
+ data->sensor[i].location = sensor_location;
+ data->sensor[i].caution_thresh = therm_limit;
+ data->sensor[i].max_op_thresh = therm_limit -
+ low_thresh_delta;
+ }
+ }
+ return 0;
+}
+
+#endif
+static struct e1000_mac_operations e1000_mac_ops_82575 = {
+ .init_hw = igb_init_hw_82575,
+ .check_for_link = igb_check_for_link_82575,
+ .rar_set = igb_rar_set,
+ .read_mac_addr = igb_read_mac_addr_82575,
+ .get_speed_and_duplex = igb_get_link_up_info_82575,
+#ifdef CONFIG_IGB_HWMON
+ .get_thermal_sensor_data = igb_get_thermal_sensor_data_generic,
+ .init_thermal_sensor_thresh = igb_init_thermal_sensor_thresh_generic,
+#endif
+};
+
+static struct e1000_phy_operations e1000_phy_ops_82575 = {
+ .acquire = igb_acquire_phy_82575,
+ .get_cfg_done = igb_get_cfg_done_82575,
+ .release = igb_release_phy_82575,
+ .write_i2c_byte = igb_write_i2c_byte,
+ .read_i2c_byte = igb_read_i2c_byte,
+};
+
+static struct e1000_nvm_operations e1000_nvm_ops_82575 = {
+ .acquire = igb_acquire_nvm_82575,
+ .read = igb_read_nvm_eerd,
+ .release = igb_release_nvm_82575,
+ .write = igb_write_nvm_spi,
+};
+
+const struct e1000_info e1000_82575_info = {
+ .get_invariants = igb_get_invariants_82575,
+ .mac_ops = &e1000_mac_ops_82575,
+ .phy_ops = &e1000_phy_ops_82575,
+ .nvm_ops = &e1000_nvm_ops_82575,
+};
+
Code Review / kvmfornfv.git / blobdiff