Add the rt linux 4.1.3-rt3 as base

[kvmfornfv.git] / kernel / drivers / net / ethernet / broadcom / Kconfig

diff --git a/kernel/drivers/net/ethernet/broadcom/Kconfig b/kernel/drivers/net/ethernet/broadcom/Kconfig
new file mode 100644 (file)
index 0000000..a6f9142
--- /dev/null
+++ b/kernel/drivers/net/ethernet/broadcom/Kconfig
@@ -0,0 +1,164 @@
+#
+# Broadcom device configuration
+#
+
+config NET_VENDOR_BROADCOM
+       bool "Broadcom devices"
+       default y
+       depends on (SSB_POSSIBLE && HAS_DMA) || PCI || BCM63XX || \
+                  SIBYTE_SB1xxx_SOC
+       ---help---
+         If you have a network (Ethernet) chipset belonging to this class,
+         say Y.
+
+         Note that the answer to this question does not directly affect
+         the kernel: saying N will just case the configurator to skip all
+         the questions regarding AMD chipsets. If you say Y, you will be asked
+         for your specific chipset/driver in the following questions.
+
+if NET_VENDOR_BROADCOM
+
+config B44
+       tristate "Broadcom 440x/47xx ethernet support"
+       depends on SSB_POSSIBLE && HAS_DMA
+       select SSB
+       select MII
+       select PHYLIB
+       ---help---
+         If you have a network (Ethernet) controller of this type, say Y
+         or M and read the Ethernet-HOWTO, available from
+         <http://www.tldp.org/docs.html#howto>.
+
+         To compile this driver as a module, choose M here. The module
+         will be called b44.
+
+# Auto-select SSB PCI-HOST support, if possible
+config B44_PCI_AUTOSELECT
+       bool
+       depends on B44 && SSB_PCIHOST_POSSIBLE
+       select SSB_PCIHOST
+       default y
+
+# Auto-select SSB PCICORE driver, if possible
+config B44_PCICORE_AUTOSELECT
+       bool
+       depends on B44 && SSB_DRIVER_PCICORE_POSSIBLE
+       select SSB_DRIVER_PCICORE
+       default y
+
+config B44_PCI
+       bool
+       depends on B44_PCI_AUTOSELECT && B44_PCICORE_AUTOSELECT
+       default y
+
+config BCM63XX_ENET
+       tristate "Broadcom 63xx internal mac support"
+       depends on BCM63XX
+       select MII
+       select PHYLIB
+       help
+         This driver supports the ethernet MACs in the Broadcom 63xx
+         MIPS chipset family (BCM63XX).
+
+config BCMGENET
+       tristate "Broadcom GENET internal MAC support"
+       select MII
+       select PHYLIB
+       select FIXED_PHY
+       select BCM7XXX_PHY
+       help
+         This driver supports the built-in Ethernet MACs found in the
+         Broadcom BCM7xxx Set Top Box family chipset.
+
+config BNX2
+       tristate "QLogic bnx2 support"
+       depends on PCI
+       select CRC32
+       select FW_LOADER
+       ---help---
+         This driver supports QLogic bnx2 gigabit Ethernet cards.
+
+         To compile this driver as a module, choose M here: the module
+         will be called bnx2.  This is recommended.
+
+config CNIC
+       tristate "QLogic CNIC support"
+       depends on PCI && (IPV6 || IPV6=n)
+       select BNX2
+       select UIO
+       ---help---
+         This driver supports offload features of QLogic bnx2 gigabit
+         Ethernet cards.
+
+         To compile this driver as a module, choose M here: the module
+         will be called cnic.  This is recommended.
+
+config SB1250_MAC
+       tristate "SB1250 Gigabit Ethernet support"
+       depends on SIBYTE_SB1xxx_SOC
+       select PHYLIB
+       ---help---
+         This driver supports Gigabit Ethernet interfaces based on the
+         Broadcom SiByte family of System-On-a-Chip parts.  They include
+         the BCM1120, BCM1125, BCM1125H, BCM1250, BCM1255, BCM1280, BCM1455
+         and BCM1480 chips.
+
+         To compile this driver as a module, choose M here: the module
+         will be called sb1250-mac.
+
+config TIGON3
+       tristate "Broadcom Tigon3 support"
+       depends on PCI
+       select PHYLIB
+       select HWMON
+       select PTP_1588_CLOCK
+       ---help---
+         This driver supports Broadcom Tigon3 based gigabit Ethernet cards.
+
+         To compile this driver as a module, choose M here: the module
+         will be called tg3.  This is recommended.
+
+config BNX2X
+       tristate "Broadcom NetXtremeII 10Gb support"
+       depends on PCI
+       select PTP_1588_CLOCK
+       select FW_LOADER
+       select ZLIB_INFLATE
+       select LIBCRC32C
+       select MDIO
+       ---help---
+         This driver supports Broadcom NetXtremeII 10 gigabit Ethernet cards.
+         To compile this driver as a module, choose M here: the module
+         will be called bnx2x.  This is recommended.
+
+config BNX2X_SRIOV
+       bool "Broadcom 578xx and 57712 SR-IOV support"
+       depends on BNX2X && PCI_IOV
+       default y
+       ---help---
+         This configuration parameter enables Single Root Input Output
+         Virtualization support in the 578xx and 57712 products. This
+         allows for virtual function acceleration in virtual environments.
+
+config BGMAC
+       tristate "BCMA bus GBit core support"
+       depends on BCMA_HOST_SOC && HAS_DMA && (BCM47XX || ARCH_BCM_5301X)
+       select PHYLIB
+       ---help---
+         This driver supports GBit MAC and BCM4706 GBit MAC cores on BCMA bus.
+         They can be found on BCM47xx SoCs and provide gigabit ethernet.
+         In case of using this driver on BCM4706 it's also requires to enable
+         BCMA_DRIVER_GMAC_CMN to make it work.
+
+config SYSTEMPORT
+       tristate "Broadcom SYSTEMPORT internal MAC support"
+       depends on OF
+       select MII
+       select PHYLIB
+       select FIXED_PHY
+       help
+         This driver supports the built-in Ethernet MACs found in the
+         Broadcom BCM7xxx Set Top Box family chipset using an internal
+         Ethernet switch.
+
+endif # NET_VENDOR_BROADCOM