--- /dev/null
+/*
+ * linux/drivers/mmc/host/pxa.c - PXA MMCI driver
+ *
+ * Copyright (C) 2003 Russell King, All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This hardware is really sick:
+ * - No way to clear interrupts.
+ * - Have to turn off the clock whenever we touch the device.
+ * - Doesn't tell you how many data blocks were transferred.
+ * Yuck!
+ *
+ * 1 and 3 byte data transfers not supported
+ * max block length up to 1023
+ */
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/ioport.h>
+#include <linux/platform_device.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/dma-mapping.h>
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/mmc/host.h>
+#include <linux/io.h>
+#include <linux/regulator/consumer.h>
+#include <linux/gpio.h>
+#include <linux/gfp.h>
+#include <linux/of.h>
+#include <linux/of_gpio.h>
+#include <linux/of_device.h>
+
+#include <asm/sizes.h>
+
+#include <mach/hardware.h>
+#include <mach/dma.h>
+#include <linux/platform_data/mmc-pxamci.h>
+
+#include "pxamci.h"
+
+#define DRIVER_NAME "pxa2xx-mci"
+
+#define NR_SG 1
+#define CLKRT_OFF (~0)
+
+#define mmc_has_26MHz() (cpu_is_pxa300() || cpu_is_pxa310() \
+ || cpu_is_pxa935())
+
+struct pxamci_host {
+ struct mmc_host *mmc;
+ spinlock_t lock;
+ struct resource *res;
+ void __iomem *base;
+ struct clk *clk;
+ unsigned long clkrate;
+ int irq;
+ int dma;
+ unsigned int clkrt;
+ unsigned int cmdat;
+ unsigned int imask;
+ unsigned int power_mode;
+ struct pxamci_platform_data *pdata;
+
+ struct mmc_request *mrq;
+ struct mmc_command *cmd;
+ struct mmc_data *data;
+
+ dma_addr_t sg_dma;
+ struct pxa_dma_desc *sg_cpu;
+ unsigned int dma_len;
+
+ unsigned int dma_dir;
+ unsigned int dma_drcmrrx;
+ unsigned int dma_drcmrtx;
+
+ struct regulator *vcc;
+};
+
+static inline void pxamci_init_ocr(struct pxamci_host *host)
+{
+#ifdef CONFIG_REGULATOR
+ host->vcc = regulator_get_optional(mmc_dev(host->mmc), "vmmc");
+
+ if (IS_ERR(host->vcc))
+ host->vcc = NULL;
+ else {
+ host->mmc->ocr_avail = mmc_regulator_get_ocrmask(host->vcc);
+ if (host->pdata && host->pdata->ocr_mask)
+ dev_warn(mmc_dev(host->mmc),
+ "ocr_mask/setpower will not be used\n");
+ }
+#endif
+ if (host->vcc == NULL) {
+ /* fall-back to platform data */
+ host->mmc->ocr_avail = host->pdata ?
+ host->pdata->ocr_mask :
+ MMC_VDD_32_33 | MMC_VDD_33_34;
+ }
+}
+
+static inline int pxamci_set_power(struct pxamci_host *host,
+ unsigned char power_mode,
+ unsigned int vdd)
+{
+ int on;
+
+ if (host->vcc) {
+ int ret;
+
+ if (power_mode == MMC_POWER_UP) {
+ ret = mmc_regulator_set_ocr(host->mmc, host->vcc, vdd);
+ if (ret)
+ return ret;
+ } else if (power_mode == MMC_POWER_OFF) {
+ ret = mmc_regulator_set_ocr(host->mmc, host->vcc, 0);
+ if (ret)
+ return ret;
+ }
+ }
+ if (!host->vcc && host->pdata &&
+ gpio_is_valid(host->pdata->gpio_power)) {
+ on = ((1 << vdd) & host->pdata->ocr_mask);
+ gpio_set_value(host->pdata->gpio_power,
+ !!on ^ host->pdata->gpio_power_invert);
+ }
+ if (!host->vcc && host->pdata && host->pdata->setpower)
+ return host->pdata->setpower(mmc_dev(host->mmc), vdd);
+
+ return 0;
+}
+
+static void pxamci_stop_clock(struct pxamci_host *host)
+{
+ if (readl(host->base + MMC_STAT) & STAT_CLK_EN) {
+ unsigned long timeout = 10000;
+ unsigned int v;
+
+ writel(STOP_CLOCK, host->base + MMC_STRPCL);
+
+ do {
+ v = readl(host->base + MMC_STAT);
+ if (!(v & STAT_CLK_EN))
+ break;
+ udelay(1);
+ } while (timeout--);
+
+ if (v & STAT_CLK_EN)
+ dev_err(mmc_dev(host->mmc), "unable to stop clock\n");
+ }
+}
+
+static void pxamci_enable_irq(struct pxamci_host *host, unsigned int mask)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&host->lock, flags);
+ host->imask &= ~mask;
+ writel(host->imask, host->base + MMC_I_MASK);
+ spin_unlock_irqrestore(&host->lock, flags);
+}
+
+static void pxamci_disable_irq(struct pxamci_host *host, unsigned int mask)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&host->lock, flags);
+ host->imask |= mask;
+ writel(host->imask, host->base + MMC_I_MASK);
+ spin_unlock_irqrestore(&host->lock, flags);
+}
+
+static void pxamci_setup_data(struct pxamci_host *host, struct mmc_data *data)
+{
+ unsigned int nob = data->blocks;
+ unsigned long long clks;
+ unsigned int timeout;
+ bool dalgn = 0;
+ u32 dcmd;
+ int i;
+
+ host->data = data;
+
+ if (data->flags & MMC_DATA_STREAM)
+ nob = 0xffff;
+
+ writel(nob, host->base + MMC_NOB);
+ writel(data->blksz, host->base + MMC_BLKLEN);
+
+ clks = (unsigned long long)data->timeout_ns * host->clkrate;
+ do_div(clks, 1000000000UL);
+ timeout = (unsigned int)clks + (data->timeout_clks << host->clkrt);
+ writel((timeout + 255) / 256, host->base + MMC_RDTO);
+
+ if (data->flags & MMC_DATA_READ) {
+ host->dma_dir = DMA_FROM_DEVICE;
+ dcmd = DCMD_INCTRGADDR | DCMD_FLOWSRC;
+ DRCMR(host->dma_drcmrtx) = 0;
+ DRCMR(host->dma_drcmrrx) = host->dma | DRCMR_MAPVLD;
+ } else {
+ host->dma_dir = DMA_TO_DEVICE;
+ dcmd = DCMD_INCSRCADDR | DCMD_FLOWTRG;
+ DRCMR(host->dma_drcmrrx) = 0;
+ DRCMR(host->dma_drcmrtx) = host->dma | DRCMR_MAPVLD;
+ }
+
+ dcmd |= DCMD_BURST32 | DCMD_WIDTH1;
+
+ host->dma_len = dma_map_sg(mmc_dev(host->mmc), data->sg, data->sg_len,
+ host->dma_dir);
+
+ for (i = 0; i < host->dma_len; i++) {
+ unsigned int length = sg_dma_len(&data->sg[i]);
+ host->sg_cpu[i].dcmd = dcmd | length;
+ if (length & 31 && !(data->flags & MMC_DATA_READ))
+ host->sg_cpu[i].dcmd |= DCMD_ENDIRQEN;
+ /* Not aligned to 8-byte boundary? */
+ if (sg_dma_address(&data->sg[i]) & 0x7)
+ dalgn = 1;
+ if (data->flags & MMC_DATA_READ) {
+ host->sg_cpu[i].dsadr = host->res->start + MMC_RXFIFO;
+ host->sg_cpu[i].dtadr = sg_dma_address(&data->sg[i]);
+ } else {
+ host->sg_cpu[i].dsadr = sg_dma_address(&data->sg[i]);
+ host->sg_cpu[i].dtadr = host->res->start + MMC_TXFIFO;
+ }
+ host->sg_cpu[i].ddadr = host->sg_dma + (i + 1) *
+ sizeof(struct pxa_dma_desc);
+ }
+ host->sg_cpu[host->dma_len - 1].ddadr = DDADR_STOP;
+ wmb();
+
+ /*
+ * The PXA27x DMA controller encounters overhead when working with
+ * unaligned (to 8-byte boundaries) data, so switch on byte alignment
+ * mode only if we have unaligned data.
+ */
+ if (dalgn)
+ DALGN |= (1 << host->dma);
+ else
+ DALGN &= ~(1 << host->dma);
+ DDADR(host->dma) = host->sg_dma;
+
+ /*
+ * workaround for erratum #91:
+ * only start DMA now if we are doing a read,
+ * otherwise we wait until CMD/RESP has finished
+ * before starting DMA.
+ */
+ if (!cpu_is_pxa27x() || data->flags & MMC_DATA_READ)
+ DCSR(host->dma) = DCSR_RUN;
+}
+
+static void pxamci_start_cmd(struct pxamci_host *host, struct mmc_command *cmd, unsigned int cmdat)
+{
+ WARN_ON(host->cmd != NULL);
+ host->cmd = cmd;
+
+ if (cmd->flags & MMC_RSP_BUSY)
+ cmdat |= CMDAT_BUSY;
+
+#define RSP_TYPE(x) ((x) & ~(MMC_RSP_BUSY|MMC_RSP_OPCODE))
+ switch (RSP_TYPE(mmc_resp_type(cmd))) {
+ case RSP_TYPE(MMC_RSP_R1): /* r1, r1b, r6, r7 */
+ cmdat |= CMDAT_RESP_SHORT;
+ break;
+ case RSP_TYPE(MMC_RSP_R3):
+ cmdat |= CMDAT_RESP_R3;
+ break;
+ case RSP_TYPE(MMC_RSP_R2):
+ cmdat |= CMDAT_RESP_R2;
+ break;
+ default:
+ break;
+ }
+
+ writel(cmd->opcode, host->base + MMC_CMD);
+ writel(cmd->arg >> 16, host->base + MMC_ARGH);
+ writel(cmd->arg & 0xffff, host->base + MMC_ARGL);
+ writel(cmdat, host->base + MMC_CMDAT);
+ writel(host->clkrt, host->base + MMC_CLKRT);
+
+ writel(START_CLOCK, host->base + MMC_STRPCL);
+
+ pxamci_enable_irq(host, END_CMD_RES);
+}
+
+static void pxamci_finish_request(struct pxamci_host *host, struct mmc_request *mrq)
+{
+ host->mrq = NULL;
+ host->cmd = NULL;
+ host->data = NULL;
+ mmc_request_done(host->mmc, mrq);
+}
+
+static int pxamci_cmd_done(struct pxamci_host *host, unsigned int stat)
+{
+ struct mmc_command *cmd = host->cmd;
+ int i;
+ u32 v;
+
+ if (!cmd)
+ return 0;
+
+ host->cmd = NULL;
+
+ /*
+ * Did I mention this is Sick. We always need to
+ * discard the upper 8 bits of the first 16-bit word.
+ */
+ v = readl(host->base + MMC_RES) & 0xffff;
+ for (i = 0; i < 4; i++) {
+ u32 w1 = readl(host->base + MMC_RES) & 0xffff;
+ u32 w2 = readl(host->base + MMC_RES) & 0xffff;
+ cmd->resp[i] = v << 24 | w1 << 8 | w2 >> 8;
+ v = w2;
+ }
+
+ if (stat & STAT_TIME_OUT_RESPONSE) {
+ cmd->error = -ETIMEDOUT;
+ } else if (stat & STAT_RES_CRC_ERR && cmd->flags & MMC_RSP_CRC) {
+ /*
+ * workaround for erratum #42:
+ * Intel PXA27x Family Processor Specification Update Rev 001
+ * A bogus CRC error can appear if the msb of a 136 bit
+ * response is a one.
+ */
+ if (cpu_is_pxa27x() &&
+ (cmd->flags & MMC_RSP_136 && cmd->resp[0] & 0x80000000))
+ pr_debug("ignoring CRC from command %d - *risky*\n", cmd->opcode);
+ else
+ cmd->error = -EILSEQ;
+ }
+
+ pxamci_disable_irq(host, END_CMD_RES);
+ if (host->data && !cmd->error) {
+ pxamci_enable_irq(host, DATA_TRAN_DONE);
+ /*
+ * workaround for erratum #91, if doing write
+ * enable DMA late
+ */
+ if (cpu_is_pxa27x() && host->data->flags & MMC_DATA_WRITE)
+ DCSR(host->dma) = DCSR_RUN;
+ } else {
+ pxamci_finish_request(host, host->mrq);
+ }
+
+ return 1;
+}
+
+static int pxamci_data_done(struct pxamci_host *host, unsigned int stat)
+{
+ struct mmc_data *data = host->data;
+
+ if (!data)
+ return 0;
+
+ DCSR(host->dma) = 0;
+ dma_unmap_sg(mmc_dev(host->mmc), data->sg, data->sg_len,
+ host->dma_dir);
+
+ if (stat & STAT_READ_TIME_OUT)
+ data->error = -ETIMEDOUT;
+ else if (stat & (STAT_CRC_READ_ERROR|STAT_CRC_WRITE_ERROR))
+ data->error = -EILSEQ;
+
+ /*
+ * There appears to be a hardware design bug here. There seems to
+ * be no way to find out how much data was transferred to the card.
+ * This means that if there was an error on any block, we mark all
+ * data blocks as being in error.
+ */
+ if (!data->error)
+ data->bytes_xfered = data->blocks * data->blksz;
+ else
+ data->bytes_xfered = 0;
+
+ pxamci_disable_irq(host, DATA_TRAN_DONE);
+
+ host->data = NULL;
+ if (host->mrq->stop) {
+ pxamci_stop_clock(host);
+ pxamci_start_cmd(host, host->mrq->stop, host->cmdat);
+ } else {
+ pxamci_finish_request(host, host->mrq);
+ }
+
+ return 1;
+}
+
+static irqreturn_t pxamci_irq(int irq, void *devid)
+{
+ struct pxamci_host *host = devid;
+ unsigned int ireg;
+ int handled = 0;
+
+ ireg = readl(host->base + MMC_I_REG) & ~readl(host->base + MMC_I_MASK);
+
+ if (ireg) {
+ unsigned stat = readl(host->base + MMC_STAT);
+
+ pr_debug("PXAMCI: irq %08x stat %08x\n", ireg, stat);
+
+ if (ireg & END_CMD_RES)
+ handled |= pxamci_cmd_done(host, stat);
+ if (ireg & DATA_TRAN_DONE)
+ handled |= pxamci_data_done(host, stat);
+ if (ireg & SDIO_INT) {
+ mmc_signal_sdio_irq(host->mmc);
+ handled = 1;
+ }
+ }
+
+ return IRQ_RETVAL(handled);
+}
+
+static void pxamci_request(struct mmc_host *mmc, struct mmc_request *mrq)
+{
+ struct pxamci_host *host = mmc_priv(mmc);
+ unsigned int cmdat;
+
+ WARN_ON(host->mrq != NULL);
+
+ host->mrq = mrq;
+
+ pxamci_stop_clock(host);
+
+ cmdat = host->cmdat;
+ host->cmdat &= ~CMDAT_INIT;
+
+ if (mrq->data) {
+ pxamci_setup_data(host, mrq->data);
+
+ cmdat &= ~CMDAT_BUSY;
+ cmdat |= CMDAT_DATAEN | CMDAT_DMAEN;
+ if (mrq->data->flags & MMC_DATA_WRITE)
+ cmdat |= CMDAT_WRITE;
+
+ if (mrq->data->flags & MMC_DATA_STREAM)
+ cmdat |= CMDAT_STREAM;
+ }
+
+ pxamci_start_cmd(host, mrq->cmd, cmdat);
+}
+
+static int pxamci_get_ro(struct mmc_host *mmc)
+{
+ struct pxamci_host *host = mmc_priv(mmc);
+
+ if (host->pdata && gpio_is_valid(host->pdata->gpio_card_ro)) {
+ if (host->pdata->gpio_card_ro_invert)
+ return !gpio_get_value(host->pdata->gpio_card_ro);
+ else
+ return gpio_get_value(host->pdata->gpio_card_ro);
+ }
+ if (host->pdata && host->pdata->get_ro)
+ return !!host->pdata->get_ro(mmc_dev(mmc));
+ /*
+ * Board doesn't support read only detection; let the mmc core
+ * decide what to do.
+ */
+ return -ENOSYS;
+}
+
+static void pxamci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
+{
+ struct pxamci_host *host = mmc_priv(mmc);
+
+ if (ios->clock) {
+ unsigned long rate = host->clkrate;
+ unsigned int clk = rate / ios->clock;
+
+ if (host->clkrt == CLKRT_OFF)
+ clk_prepare_enable(host->clk);
+
+ if (ios->clock == 26000000) {
+ /* to support 26MHz */
+ host->clkrt = 7;
+ } else {
+ /* to handle (19.5MHz, 26MHz) */
+ if (!clk)
+ clk = 1;
+
+ /*
+ * clk might result in a lower divisor than we
+ * desire. check for that condition and adjust
+ * as appropriate.
+ */
+ if (rate / clk > ios->clock)
+ clk <<= 1;
+ host->clkrt = fls(clk) - 1;
+ }
+
+ /*
+ * we write clkrt on the next command
+ */
+ } else {
+ pxamci_stop_clock(host);
+ if (host->clkrt != CLKRT_OFF) {
+ host->clkrt = CLKRT_OFF;
+ clk_disable_unprepare(host->clk);
+ }
+ }
+
+ if (host->power_mode != ios->power_mode) {
+ int ret;
+
+ host->power_mode = ios->power_mode;
+
+ ret = pxamci_set_power(host, ios->power_mode, ios->vdd);
+ if (ret) {
+ dev_err(mmc_dev(mmc), "unable to set power\n");
+ /*
+ * The .set_ios() function in the mmc_host_ops
+ * struct return void, and failing to set the
+ * power should be rare so we print an error and
+ * return here.
+ */
+ return;
+ }
+
+ if (ios->power_mode == MMC_POWER_ON)
+ host->cmdat |= CMDAT_INIT;
+ }
+
+ if (ios->bus_width == MMC_BUS_WIDTH_4)
+ host->cmdat |= CMDAT_SD_4DAT;
+ else
+ host->cmdat &= ~CMDAT_SD_4DAT;
+
+ dev_dbg(mmc_dev(mmc), "PXAMCI: clkrt = %x cmdat = %x\n",
+ host->clkrt, host->cmdat);
+}
+
+static void pxamci_enable_sdio_irq(struct mmc_host *host, int enable)
+{
+ struct pxamci_host *pxa_host = mmc_priv(host);
+
+ if (enable)
+ pxamci_enable_irq(pxa_host, SDIO_INT);
+ else
+ pxamci_disable_irq(pxa_host, SDIO_INT);
+}
+
+static const struct mmc_host_ops pxamci_ops = {
+ .request = pxamci_request,
+ .get_ro = pxamci_get_ro,
+ .set_ios = pxamci_set_ios,
+ .enable_sdio_irq = pxamci_enable_sdio_irq,
+};
+
+static void pxamci_dma_irq(int dma, void *devid)
+{
+ struct pxamci_host *host = devid;
+ int dcsr = DCSR(dma);
+ DCSR(dma) = dcsr & ~DCSR_STOPIRQEN;
+
+ if (dcsr & DCSR_ENDINTR) {
+ writel(BUF_PART_FULL, host->base + MMC_PRTBUF);
+ } else {
+ pr_err("%s: DMA error on channel %d (DCSR=%#x)\n",
+ mmc_hostname(host->mmc), dma, dcsr);
+ host->data->error = -EIO;
+ pxamci_data_done(host, 0);
+ }
+}
+
+static irqreturn_t pxamci_detect_irq(int irq, void *devid)
+{
+ struct pxamci_host *host = mmc_priv(devid);
+
+ mmc_detect_change(devid, msecs_to_jiffies(host->pdata->detect_delay_ms));
+ return IRQ_HANDLED;
+}
+
+#ifdef CONFIG_OF
+static const struct of_device_id pxa_mmc_dt_ids[] = {
+ { .compatible = "marvell,pxa-mmc" },
+ { }
+};
+
+MODULE_DEVICE_TABLE(of, pxa_mmc_dt_ids);
+
+static int pxamci_of_init(struct platform_device *pdev)
+{
+ struct device_node *np = pdev->dev.of_node;
+ struct pxamci_platform_data *pdata;
+ u32 tmp;
+
+ if (!np)
+ return 0;
+
+ pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
+ if (!pdata)
+ return -ENOMEM;
+
+ pdata->gpio_card_detect =
+ of_get_named_gpio(np, "cd-gpios", 0);
+ pdata->gpio_card_ro =
+ of_get_named_gpio(np, "wp-gpios", 0);
+
+ /* pxa-mmc specific */
+ pdata->gpio_power =
+ of_get_named_gpio(np, "pxa-mmc,gpio-power", 0);
+
+ if (of_property_read_u32(np, "pxa-mmc,detect-delay-ms", &tmp) == 0)
+ pdata->detect_delay_ms = tmp;
+
+ pdev->dev.platform_data = pdata;
+
+ return 0;
+}
+#else
+static int pxamci_of_init(struct platform_device *pdev)
+{
+ return 0;
+}
+#endif
+
+static int pxamci_probe(struct platform_device *pdev)
+{
+ struct mmc_host *mmc;
+ struct pxamci_host *host = NULL;
+ struct resource *r, *dmarx, *dmatx;
+ int ret, irq, gpio_cd = -1, gpio_ro = -1, gpio_power = -1;
+
+ ret = pxamci_of_init(pdev);
+ if (ret)
+ return ret;
+
+ r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ irq = platform_get_irq(pdev, 0);
+ if (!r || irq < 0)
+ return -ENXIO;
+
+ r = request_mem_region(r->start, SZ_4K, DRIVER_NAME);
+ if (!r)
+ return -EBUSY;
+
+ mmc = mmc_alloc_host(sizeof(struct pxamci_host), &pdev->dev);
+ if (!mmc) {
+ ret = -ENOMEM;
+ goto out;
+ }
+
+ mmc->ops = &pxamci_ops;
+
+ /*
+ * We can do SG-DMA, but we don't because we never know how much
+ * data we successfully wrote to the card.
+ */
+ mmc->max_segs = NR_SG;
+
+ /*
+ * Our hardware DMA can handle a maximum of one page per SG entry.
+ */
+ mmc->max_seg_size = PAGE_SIZE;
+
+ /*
+ * Block length register is only 10 bits before PXA27x.
+ */
+ mmc->max_blk_size = cpu_is_pxa25x() ? 1023 : 2048;
+
+ /*
+ * Block count register is 16 bits.
+ */
+ mmc->max_blk_count = 65535;
+
+ host = mmc_priv(mmc);
+ host->mmc = mmc;
+ host->dma = -1;
+ host->pdata = pdev->dev.platform_data;
+ host->clkrt = CLKRT_OFF;
+
+ host->clk = clk_get(&pdev->dev, NULL);
+ if (IS_ERR(host->clk)) {
+ ret = PTR_ERR(host->clk);
+ host->clk = NULL;
+ goto out;
+ }
+
+ host->clkrate = clk_get_rate(host->clk);
+
+ /*
+ * Calculate minimum clock rate, rounding up.
+ */
+ mmc->f_min = (host->clkrate + 63) / 64;
+ mmc->f_max = (mmc_has_26MHz()) ? 26000000 : host->clkrate;
+
+ pxamci_init_ocr(host);
+
+ mmc->caps = 0;
+ host->cmdat = 0;
+ if (!cpu_is_pxa25x()) {
+ mmc->caps |= MMC_CAP_4_BIT_DATA | MMC_CAP_SDIO_IRQ;
+ host->cmdat |= CMDAT_SDIO_INT_EN;
+ if (mmc_has_26MHz())
+ mmc->caps |= MMC_CAP_MMC_HIGHSPEED |
+ MMC_CAP_SD_HIGHSPEED;
+ }
+
+ host->sg_cpu = dma_alloc_coherent(&pdev->dev, PAGE_SIZE, &host->sg_dma, GFP_KERNEL);
+ if (!host->sg_cpu) {
+ ret = -ENOMEM;
+ goto out;
+ }
+
+ spin_lock_init(&host->lock);
+ host->res = r;
+ host->irq = irq;
+ host->imask = MMC_I_MASK_ALL;
+
+ host->base = ioremap(r->start, SZ_4K);
+ if (!host->base) {
+ ret = -ENOMEM;
+ goto out;
+ }
+
+ /*
+ * Ensure that the host controller is shut down, and setup
+ * with our defaults.
+ */
+ pxamci_stop_clock(host);
+ writel(0, host->base + MMC_SPI);
+ writel(64, host->base + MMC_RESTO);
+ writel(host->imask, host->base + MMC_I_MASK);
+
+ host->dma = pxa_request_dma(DRIVER_NAME, DMA_PRIO_LOW,
+ pxamci_dma_irq, host);
+ if (host->dma < 0) {
+ ret = -EBUSY;
+ goto out;
+ }
+
+ ret = request_irq(host->irq, pxamci_irq, 0, DRIVER_NAME, host);
+ if (ret)
+ goto out;
+
+ platform_set_drvdata(pdev, mmc);
+
+ dmarx = platform_get_resource(pdev, IORESOURCE_DMA, 0);
+ if (!dmarx) {
+ ret = -ENXIO;
+ goto out;
+ }
+ host->dma_drcmrrx = dmarx->start;
+
+ dmatx = platform_get_resource(pdev, IORESOURCE_DMA, 1);
+ if (!dmatx) {
+ ret = -ENXIO;
+ goto out;
+ }
+ host->dma_drcmrtx = dmatx->start;
+
+ if (host->pdata) {
+ gpio_cd = host->pdata->gpio_card_detect;
+ gpio_ro = host->pdata->gpio_card_ro;
+ gpio_power = host->pdata->gpio_power;
+ }
+ if (gpio_is_valid(gpio_power)) {
+ ret = gpio_request(gpio_power, "mmc card power");
+ if (ret) {
+ dev_err(&pdev->dev, "Failed requesting gpio_power %d\n", gpio_power);
+ goto out;
+ }
+ gpio_direction_output(gpio_power,
+ host->pdata->gpio_power_invert);
+ }
+ if (gpio_is_valid(gpio_ro)) {
+ ret = gpio_request(gpio_ro, "mmc card read only");
+ if (ret) {
+ dev_err(&pdev->dev, "Failed requesting gpio_ro %d\n", gpio_ro);
+ goto err_gpio_ro;
+ }
+ gpio_direction_input(gpio_ro);
+ }
+ if (gpio_is_valid(gpio_cd)) {
+ ret = gpio_request(gpio_cd, "mmc card detect");
+ if (ret) {
+ dev_err(&pdev->dev, "Failed requesting gpio_cd %d\n", gpio_cd);
+ goto err_gpio_cd;
+ }
+ gpio_direction_input(gpio_cd);
+
+ ret = request_irq(gpio_to_irq(gpio_cd), pxamci_detect_irq,
+ IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
+ "mmc card detect", mmc);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to request card detect IRQ\n");
+ goto err_request_irq;
+ }
+ }
+
+ if (host->pdata && host->pdata->init)
+ host->pdata->init(&pdev->dev, pxamci_detect_irq, mmc);
+
+ if (gpio_is_valid(gpio_power) && host->pdata->setpower)
+ dev_warn(&pdev->dev, "gpio_power and setpower() both defined\n");
+ if (gpio_is_valid(gpio_ro) && host->pdata->get_ro)
+ dev_warn(&pdev->dev, "gpio_ro and get_ro() both defined\n");
+
+ mmc_add_host(mmc);
+
+ return 0;
+
+err_request_irq:
+ gpio_free(gpio_cd);
+err_gpio_cd:
+ gpio_free(gpio_ro);
+err_gpio_ro:
+ gpio_free(gpio_power);
+ out:
+ if (host) {
+ if (host->dma >= 0)
+ pxa_free_dma(host->dma);
+ if (host->base)
+ iounmap(host->base);
+ if (host->sg_cpu)
+ dma_free_coherent(&pdev->dev, PAGE_SIZE, host->sg_cpu, host->sg_dma);
+ if (host->clk)
+ clk_put(host->clk);
+ }
+ if (mmc)
+ mmc_free_host(mmc);
+ release_resource(r);
+ return ret;
+}
+
+static int pxamci_remove(struct platform_device *pdev)
+{
+ struct mmc_host *mmc = platform_get_drvdata(pdev);
+ int gpio_cd = -1, gpio_ro = -1, gpio_power = -1;
+
+ if (mmc) {
+ struct pxamci_host *host = mmc_priv(mmc);
+
+ mmc_remove_host(mmc);
+
+ if (host->pdata) {
+ gpio_cd = host->pdata->gpio_card_detect;
+ gpio_ro = host->pdata->gpio_card_ro;
+ gpio_power = host->pdata->gpio_power;
+ }
+ if (gpio_is_valid(gpio_cd)) {
+ free_irq(gpio_to_irq(gpio_cd), mmc);
+ gpio_free(gpio_cd);
+ }
+ if (gpio_is_valid(gpio_ro))
+ gpio_free(gpio_ro);
+ if (gpio_is_valid(gpio_power))
+ gpio_free(gpio_power);
+ if (host->vcc)
+ regulator_put(host->vcc);
+
+ if (host->pdata && host->pdata->exit)
+ host->pdata->exit(&pdev->dev, mmc);
+
+ pxamci_stop_clock(host);
+ writel(TXFIFO_WR_REQ|RXFIFO_RD_REQ|CLK_IS_OFF|STOP_CMD|
+ END_CMD_RES|PRG_DONE|DATA_TRAN_DONE,
+ host->base + MMC_I_MASK);
+
+ DRCMR(host->dma_drcmrrx) = 0;
+ DRCMR(host->dma_drcmrtx) = 0;
+
+ free_irq(host->irq, host);
+ pxa_free_dma(host->dma);
+ iounmap(host->base);
+ dma_free_coherent(&pdev->dev, PAGE_SIZE, host->sg_cpu, host->sg_dma);
+
+ clk_put(host->clk);
+
+ release_resource(host->res);
+
+ mmc_free_host(mmc);
+ }
+ return 0;
+}
+
+static struct platform_driver pxamci_driver = {
+ .probe = pxamci_probe,
+ .remove = pxamci_remove,
+ .driver = {
+ .name = DRIVER_NAME,
+ .of_match_table = of_match_ptr(pxa_mmc_dt_ids),
+ },
+};
+
+module_platform_driver(pxamci_driver);
+
+MODULE_DESCRIPTION("PXA Multimedia Card Interface Driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:pxa2xx-mci");
Code Review / kvmfornfv.git / blobdiff