Add the rt linux 4.1.3-rt3 as base

[kvmfornfv.git] / kernel / drivers / media / usb / dvb-usb / friio.h

diff --git a/kernel/drivers/media/usb/dvb-usb/friio.h b/kernel/drivers/media/usb/dvb-usb/friio.h
new file mode 100644 (file)
index 0000000..0f461ca
--- /dev/null
+++ b/kernel/drivers/media/usb/dvb-usb/friio.h
@@ -0,0 +1,99 @@
+/* DVB USB compliant Linux driver for the Friio USB2.0 ISDB-T receiver.
+ *
+ * Copyright (C) 2009 Akihiro Tsukada <tskd2@yahoo.co.jp>
+ *
+ * This module is based off the the gl861 and vp702x modules.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation, version 2.
+ *
+ * see Documentation/dvb/README.dvb-usb for more information
+ */
+#ifndef _DVB_USB_FRIIO_H_
+#define _DVB_USB_FRIIO_H_
+
+/**
+ *      Friio Components
+ *       USB hub:                                AU4254
+ *         USB controller(+ TS dmx & streaming): GL861
+ *         Frontend:                             comtech JDVBT-90502
+ *             (tuner PLL:                       tua6034, I2C addr:(0xC0 >> 1))
+ *             (OFDM demodulator:                TC90502, I2C addr:(0x30 >> 1))
+ *         LED x3 (+LNB) control:                PIC 16F676
+ *         EEPROM:                               24C08
+ *
+ *        (USB smart card reader:                AU9522)
+ *
+ */
+
+#define DVB_USB_LOG_PREFIX "friio"
+#include "dvb-usb.h"
+
+extern int dvb_usb_friio_debug;
+#define deb_info(args...) dprintk(dvb_usb_friio_debug, 0x01, args)
+#define deb_xfer(args...) dprintk(dvb_usb_friio_debug, 0x02, args)
+#define deb_rc(args...)   dprintk(dvb_usb_friio_debug, 0x04, args)
+#define deb_fe(args...)   dprintk(dvb_usb_friio_debug, 0x08, args)
+
+/* Vendor requests */
+#define GL861_WRITE            0x40
+#define GL861_READ             0xc0
+
+/* command bytes */
+#define GL861_REQ_I2C_WRITE    0x01
+#define GL861_REQ_I2C_READ     0x02
+/* For control msg with data argument */
+/* Used for accessing the PLL on the secondary I2C bus of FE via GL861 */
+#define GL861_REQ_I2C_DATA_CTRL_WRITE  0x03
+
+#define GL861_ALTSETTING_COUNT 2
+#define FRIIO_BULK_ALTSETTING  0
+#define FRIIO_ISOC_ALTSETTING  1
+
+/* LED & LNB control via PIC. */
+/* basically, it's serial control with clock and strobe. */
+/* write the below 4bit control data to the reg 0x00 at the I2C addr 0x00 */
+/* when controlling the LEDs, 32bit(saturation, R, G, B) is sent on the bit3*/
+#define FRIIO_CTL_LNB (1 << 0)
+#define FRIIO_CTL_STROBE (1 << 1)
+#define FRIIO_CTL_CLK (1 << 2)
+#define FRIIO_CTL_LED (1 << 3)
+
+/* Front End related */
+
+#define FRIIO_DEMOD_ADDR  (0x30 >> 1)
+#define FRIIO_PLL_ADDR  (0xC0 >> 1)
+
+#define JDVBT90502_PLL_CLK     4000000
+#define JDVBT90502_PLL_DIVIDER 28
+
+#define JDVBT90502_2ND_I2C_REG 0xFE
+
+/* byte index for pll i2c command data structure*/
+/* see datasheet for tua6034 */
+#define DEMOD_REDIRECT_REG 0
+#define ADDRESS_BYTE       1
+#define DIVIDER_BYTE1      2
+#define DIVIDER_BYTE2      3
+#define CONTROL_BYTE       4
+#define BANDSWITCH_BYTE    5
+#define AGC_CTRL_BYTE      5
+#define PLL_CMD_LEN        6
+
+/* bit masks for PLL STATUS response */
+#define PLL_STATUS_POR_MODE   0x80 /* 1: Power on Reset (test) Mode */
+#define PLL_STATUS_LOCKED     0x40 /* 1: locked */
+#define PLL_STATUS_AGC_ACTIVE 0x08 /* 1:active */
+#define PLL_STATUS_TESTMODE   0x07 /* digital output level (5 level) */
+  /* 0.15Vcc step   0x00: < 0.15Vcc, ..., 0x04: >= 0.6Vcc (<= 1Vcc) */
+
+
+struct jdvbt90502_config {
+       u8 demod_address; /* i2c addr for demodulator IC */
+       u8 pll_address;   /* PLL addr on the secondary i2c*/
+};
+extern struct jdvbt90502_config friio_fe_config;
+
+extern struct dvb_frontend *jdvbt90502_attach(struct dvb_usb_device *d);
+#endif