module will be called bma150.
config INPUT_E3X0_BUTTON
- tristate "NI Ettus Research USRP E3x0 Button support."
+ tristate "NI Ettus Research USRP E3xx Button support."
default n
help
Say Y here to enable support for the NI Ettus Research
- USRP E3x0 Button.
+ USRP E3xx Button.
To compile this driver as a module, choose M here: the
module will be called e3x0_button.
depends on M68K
config INPUT_MAX77693_HAPTIC
- tristate "MAXIM MAX77693 haptic controller support"
- depends on MFD_MAX77693 && PWM
+ tristate "MAXIM MAX77693/MAX77843 haptic controller support"
+ depends on (MFD_MAX77693 || MFD_MAX77843) && PWM
select INPUT_FF_MEMLESS
help
This option enables support for the haptic controller on
- MAXIM MAX77693 chip.
+ MAXIM MAX77693 and MAX77843 chips.
To compile this driver as module, choose M here: the
module will be called max77693-haptic.
-config INPUT_MAX77843_HAPTIC
- tristate "MAXIM MAX77843 haptic controller support"
- depends on MFD_MAX77843 && REGULATOR
- select INPUT_FF_MEMLESS
- help
- This option enables support for the haptic controller on
- MAXIM MAX77843 chip. The driver supports ff-memless interface
- from input framework.
-
- To compile this driver as module, choose M here: the
- module will be called max77843-haptic.
-
config INPUT_MAX8925_ONKEY
tristate "MAX8925 ONKEY support"
depends on MFD_MAX8925
config INPUT_GP2A
tristate "Sharp GP2AP002A00F I2C Proximity/Opto sensor driver"
depends on I2C
- depends on GPIOLIB
+ depends on GPIOLIB || COMPILE_TEST
help
Say Y here if you have a Sharp GP2AP002A00F proximity/als combo-chip
hooked to an I2C bus.
config INPUT_GPIO_BEEPER
tristate "Generic GPIO Beeper support"
- depends on GPIOLIB
+ depends on GPIOLIB || COMPILE_TEST
help
Say Y here if you have a beeper connected to a GPIO pin.
config INPUT_GPIO_TILT_POLLED
tristate "Polled GPIO tilt switch"
- depends on GPIOLIB
+ depends on GPIOLIB || COMPILE_TEST
select INPUT_POLLDEV
help
This driver implements support for tilt switches connected
config INPUT_GPIO_ROTARY_ENCODER
tristate "Rotary encoders connected to GPIO pins"
- depends on GPIOLIB
+ depends on GPIOLIB || COMPILE_TEST
help
Say Y here to add support for rotary encoders connected to GPIO lines.
Check file:Documentation/input/rotary-encoder.txt for more
To compile this driver as a module, choose M here: the module
will be called da9055_onkey.
+config INPUT_DA9063_ONKEY
+ tristate "Dialog DA9062/63 OnKey"
+ depends on MFD_DA9063 || MFD_DA9062
+ help
+ Support the ONKEY of Dialog DA9063 and DA9062 Power Management ICs
+ as an input device capable of reporting the power button status.
+
+ To compile this driver as a module, choose M here: the module
+ will be called da9063_onkey.
+
config INPUT_DM355EVM
tristate "TI DaVinci DM355 EVM Keypad and IR Remote"
depends on MFD_DM355EVM_MSP
config INPUT_DRV260X_HAPTICS
tristate "TI DRV260X haptics support"
- depends on INPUT && I2C && GPIOLIB
+ depends on INPUT && I2C
+ depends on GPIOLIB || COMPILE_TEST
select INPUT_FF_MEMLESS
select REGMAP_I2C
help
To compile this driver as a module, choose M here: the
module will be called drv260x-haptics.
+config INPUT_DRV2665_HAPTICS
+ tristate "TI DRV2665 haptics support"
+ depends on INPUT && I2C
+ select INPUT_FF_MEMLESS
+ select REGMAP_I2C
+ help
+ Say Y to enable support for the TI DRV2665 haptics driver.
+
+ To compile this driver as a module, choose M here: the
+ module will be called drv2665-haptics.
+
config INPUT_DRV2667_HAPTICS
tristate "TI DRV2667 haptics support"
depends on INPUT && I2C
Say Y to enable support for the TI DRV2667 haptics driver.
To compile this driver as a module, choose M here: the
- module will be called drv260x-haptics.
+ module will be called drv2667-haptics.
endif