+++ /dev/null
-/*
- * Copyright (c) 2006, 2007 QLogic Corporation. All rights reserved.
- * Copyright (c) 2003, 2004, 2005, 2006 PathScale, Inc. All rights reserved.
- *
- * This software is available to you under a choice of one of two
- * licenses. You may choose to be licensed under the terms of the GNU
- * General Public License (GPL) Version 2, available from the file
- * COPYING in the main directory of this source tree, or the
- * OpenIB.org BSD license below:
- *
- * Redistribution and use in source and binary forms, with or
- * without modification, are permitted provided that the following
- * conditions are met:
- *
- * - Redistributions of source code must retain the above
- * copyright notice, this list of conditions and the following
- * disclaimer.
- *
- * - Redistributions in binary form must reproduce the above
- * copyright notice, this list of conditions and the following
- * disclaimer in the documentation and/or other materials
- * provided with the distribution.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
- * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS
- * BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN
- * ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
- * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
- * SOFTWARE.
- */
-
-/*
- * This file contains all of the code that is specific to the InfiniPath
- * HT chip.
- */
-
-#include <linux/vmalloc.h>
-#include <linux/pci.h>
-#include <linux/delay.h>
-#include <linux/htirq.h>
-#include <rdma/ib_verbs.h>
-
-#include "ipath_kernel.h"
-#include "ipath_registers.h"
-
-static void ipath_setup_ht_setextled(struct ipath_devdata *, u64, u64);
-
-
-/*
- * This lists the InfiniPath registers, in the actual chip layout.
- * This structure should never be directly accessed.
- *
- * The names are in InterCap form because they're taken straight from
- * the chip specification. Since they're only used in this file, they
- * don't pollute the rest of the source.
-*/
-
-struct _infinipath_do_not_use_kernel_regs {
- unsigned long long Revision;
- unsigned long long Control;
- unsigned long long PageAlign;
- unsigned long long PortCnt;
- unsigned long long DebugPortSelect;
- unsigned long long DebugPort;
- unsigned long long SendRegBase;
- unsigned long long UserRegBase;
- unsigned long long CounterRegBase;
- unsigned long long Scratch;
- unsigned long long ReservedMisc1;
- unsigned long long InterruptConfig;
- unsigned long long IntBlocked;
- unsigned long long IntMask;
- unsigned long long IntStatus;
- unsigned long long IntClear;
- unsigned long long ErrorMask;
- unsigned long long ErrorStatus;
- unsigned long long ErrorClear;
- unsigned long long HwErrMask;
- unsigned long long HwErrStatus;
- unsigned long long HwErrClear;
- unsigned long long HwDiagCtrl;
- unsigned long long MDIO;
- unsigned long long IBCStatus;
- unsigned long long IBCCtrl;
- unsigned long long ExtStatus;
- unsigned long long ExtCtrl;
- unsigned long long GPIOOut;
- unsigned long long GPIOMask;
- unsigned long long GPIOStatus;
- unsigned long long GPIOClear;
- unsigned long long RcvCtrl;
- unsigned long long RcvBTHQP;
- unsigned long long RcvHdrSize;
- unsigned long long RcvHdrCnt;
- unsigned long long RcvHdrEntSize;
- unsigned long long RcvTIDBase;
- unsigned long long RcvTIDCnt;
- unsigned long long RcvEgrBase;
- unsigned long long RcvEgrCnt;
- unsigned long long RcvBufBase;
- unsigned long long RcvBufSize;
- unsigned long long RxIntMemBase;
- unsigned long long RxIntMemSize;
- unsigned long long RcvPartitionKey;
- unsigned long long ReservedRcv[10];
- unsigned long long SendCtrl;
- unsigned long long SendPIOBufBase;
- unsigned long long SendPIOSize;
- unsigned long long SendPIOBufCnt;
- unsigned long long SendPIOAvailAddr;
- unsigned long long TxIntMemBase;
- unsigned long long TxIntMemSize;
- unsigned long long ReservedSend[9];
- unsigned long long SendBufferError;
- unsigned long long SendBufferErrorCONT1;
- unsigned long long SendBufferErrorCONT2;
- unsigned long long SendBufferErrorCONT3;
- unsigned long long ReservedSBE[4];
- unsigned long long RcvHdrAddr0;
- unsigned long long RcvHdrAddr1;
- unsigned long long RcvHdrAddr2;
- unsigned long long RcvHdrAddr3;
- unsigned long long RcvHdrAddr4;
- unsigned long long RcvHdrAddr5;
- unsigned long long RcvHdrAddr6;
- unsigned long long RcvHdrAddr7;
- unsigned long long RcvHdrAddr8;
- unsigned long long ReservedRHA[7];
- unsigned long long RcvHdrTailAddr0;
- unsigned long long RcvHdrTailAddr1;
- unsigned long long RcvHdrTailAddr2;
- unsigned long long RcvHdrTailAddr3;
- unsigned long long RcvHdrTailAddr4;
- unsigned long long RcvHdrTailAddr5;
- unsigned long long RcvHdrTailAddr6;
- unsigned long long RcvHdrTailAddr7;
- unsigned long long RcvHdrTailAddr8;
- unsigned long long ReservedRHTA[7];
- unsigned long long Sync; /* Software only */
- unsigned long long Dump; /* Software only */
- unsigned long long SimVer; /* Software only */
- unsigned long long ReservedSW[5];
- unsigned long long SerdesConfig0;
- unsigned long long SerdesConfig1;
- unsigned long long SerdesStatus;
- unsigned long long XGXSConfig;
- unsigned long long ReservedSW2[4];
-};
-
-struct _infinipath_do_not_use_counters {
- __u64 LBIntCnt;
- __u64 LBFlowStallCnt;
- __u64 Reserved1;
- __u64 TxUnsupVLErrCnt;
- __u64 TxDataPktCnt;
- __u64 TxFlowPktCnt;
- __u64 TxDwordCnt;
- __u64 TxLenErrCnt;
- __u64 TxMaxMinLenErrCnt;
- __u64 TxUnderrunCnt;
- __u64 TxFlowStallCnt;
- __u64 TxDroppedPktCnt;
- __u64 RxDroppedPktCnt;
- __u64 RxDataPktCnt;
- __u64 RxFlowPktCnt;
- __u64 RxDwordCnt;
- __u64 RxLenErrCnt;
- __u64 RxMaxMinLenErrCnt;
- __u64 RxICRCErrCnt;
- __u64 RxVCRCErrCnt;
- __u64 RxFlowCtrlErrCnt;
- __u64 RxBadFormatCnt;
- __u64 RxLinkProblemCnt;
- __u64 RxEBPCnt;
- __u64 RxLPCRCErrCnt;
- __u64 RxBufOvflCnt;
- __u64 RxTIDFullErrCnt;
- __u64 RxTIDValidErrCnt;
- __u64 RxPKeyMismatchCnt;
- __u64 RxP0HdrEgrOvflCnt;
- __u64 RxP1HdrEgrOvflCnt;
- __u64 RxP2HdrEgrOvflCnt;
- __u64 RxP3HdrEgrOvflCnt;
- __u64 RxP4HdrEgrOvflCnt;
- __u64 RxP5HdrEgrOvflCnt;
- __u64 RxP6HdrEgrOvflCnt;
- __u64 RxP7HdrEgrOvflCnt;
- __u64 RxP8HdrEgrOvflCnt;
- __u64 Reserved6;
- __u64 Reserved7;
- __u64 IBStatusChangeCnt;
- __u64 IBLinkErrRecoveryCnt;
- __u64 IBLinkDownedCnt;
- __u64 IBSymbolErrCnt;
-};
-
-#define IPATH_KREG_OFFSET(field) (offsetof( \
- struct _infinipath_do_not_use_kernel_regs, field) / sizeof(u64))
-#define IPATH_CREG_OFFSET(field) (offsetof( \
- struct _infinipath_do_not_use_counters, field) / sizeof(u64))
-
-static const struct ipath_kregs ipath_ht_kregs = {
- .kr_control = IPATH_KREG_OFFSET(Control),
- .kr_counterregbase = IPATH_KREG_OFFSET(CounterRegBase),
- .kr_debugport = IPATH_KREG_OFFSET(DebugPort),
- .kr_debugportselect = IPATH_KREG_OFFSET(DebugPortSelect),
- .kr_errorclear = IPATH_KREG_OFFSET(ErrorClear),
- .kr_errormask = IPATH_KREG_OFFSET(ErrorMask),
- .kr_errorstatus = IPATH_KREG_OFFSET(ErrorStatus),
- .kr_extctrl = IPATH_KREG_OFFSET(ExtCtrl),
- .kr_extstatus = IPATH_KREG_OFFSET(ExtStatus),
- .kr_gpio_clear = IPATH_KREG_OFFSET(GPIOClear),
- .kr_gpio_mask = IPATH_KREG_OFFSET(GPIOMask),
- .kr_gpio_out = IPATH_KREG_OFFSET(GPIOOut),
- .kr_gpio_status = IPATH_KREG_OFFSET(GPIOStatus),
- .kr_hwdiagctrl = IPATH_KREG_OFFSET(HwDiagCtrl),
- .kr_hwerrclear = IPATH_KREG_OFFSET(HwErrClear),
- .kr_hwerrmask = IPATH_KREG_OFFSET(HwErrMask),
- .kr_hwerrstatus = IPATH_KREG_OFFSET(HwErrStatus),
- .kr_ibcctrl = IPATH_KREG_OFFSET(IBCCtrl),
- .kr_ibcstatus = IPATH_KREG_OFFSET(IBCStatus),
- .kr_intblocked = IPATH_KREG_OFFSET(IntBlocked),
- .kr_intclear = IPATH_KREG_OFFSET(IntClear),
- .kr_interruptconfig = IPATH_KREG_OFFSET(InterruptConfig),
- .kr_intmask = IPATH_KREG_OFFSET(IntMask),
- .kr_intstatus = IPATH_KREG_OFFSET(IntStatus),
- .kr_mdio = IPATH_KREG_OFFSET(MDIO),
- .kr_pagealign = IPATH_KREG_OFFSET(PageAlign),
- .kr_partitionkey = IPATH_KREG_OFFSET(RcvPartitionKey),
- .kr_portcnt = IPATH_KREG_OFFSET(PortCnt),
- .kr_rcvbthqp = IPATH_KREG_OFFSET(RcvBTHQP),
- .kr_rcvbufbase = IPATH_KREG_OFFSET(RcvBufBase),
- .kr_rcvbufsize = IPATH_KREG_OFFSET(RcvBufSize),
- .kr_rcvctrl = IPATH_KREG_OFFSET(RcvCtrl),
- .kr_rcvegrbase = IPATH_KREG_OFFSET(RcvEgrBase),
- .kr_rcvegrcnt = IPATH_KREG_OFFSET(RcvEgrCnt),
- .kr_rcvhdrcnt = IPATH_KREG_OFFSET(RcvHdrCnt),
- .kr_rcvhdrentsize = IPATH_KREG_OFFSET(RcvHdrEntSize),
- .kr_rcvhdrsize = IPATH_KREG_OFFSET(RcvHdrSize),
- .kr_rcvintmembase = IPATH_KREG_OFFSET(RxIntMemBase),
- .kr_rcvintmemsize = IPATH_KREG_OFFSET(RxIntMemSize),
- .kr_rcvtidbase = IPATH_KREG_OFFSET(RcvTIDBase),
- .kr_rcvtidcnt = IPATH_KREG_OFFSET(RcvTIDCnt),
- .kr_revision = IPATH_KREG_OFFSET(Revision),
- .kr_scratch = IPATH_KREG_OFFSET(Scratch),
- .kr_sendbuffererror = IPATH_KREG_OFFSET(SendBufferError),
- .kr_sendctrl = IPATH_KREG_OFFSET(SendCtrl),
- .kr_sendpioavailaddr = IPATH_KREG_OFFSET(SendPIOAvailAddr),
- .kr_sendpiobufbase = IPATH_KREG_OFFSET(SendPIOBufBase),
- .kr_sendpiobufcnt = IPATH_KREG_OFFSET(SendPIOBufCnt),
- .kr_sendpiosize = IPATH_KREG_OFFSET(SendPIOSize),
- .kr_sendregbase = IPATH_KREG_OFFSET(SendRegBase),
- .kr_txintmembase = IPATH_KREG_OFFSET(TxIntMemBase),
- .kr_txintmemsize = IPATH_KREG_OFFSET(TxIntMemSize),
- .kr_userregbase = IPATH_KREG_OFFSET(UserRegBase),
- .kr_serdesconfig0 = IPATH_KREG_OFFSET(SerdesConfig0),
- .kr_serdesconfig1 = IPATH_KREG_OFFSET(SerdesConfig1),
- .kr_serdesstatus = IPATH_KREG_OFFSET(SerdesStatus),
- .kr_xgxsconfig = IPATH_KREG_OFFSET(XGXSConfig),
- /*
- * These should not be used directly via ipath_write_kreg64(),
- * use them with ipath_write_kreg64_port(),
- */
- .kr_rcvhdraddr = IPATH_KREG_OFFSET(RcvHdrAddr0),
- .kr_rcvhdrtailaddr = IPATH_KREG_OFFSET(RcvHdrTailAddr0)
-};
-
-static const struct ipath_cregs ipath_ht_cregs = {
- .cr_badformatcnt = IPATH_CREG_OFFSET(RxBadFormatCnt),
- .cr_erricrccnt = IPATH_CREG_OFFSET(RxICRCErrCnt),
- .cr_errlinkcnt = IPATH_CREG_OFFSET(RxLinkProblemCnt),
- .cr_errlpcrccnt = IPATH_CREG_OFFSET(RxLPCRCErrCnt),
- .cr_errpkey = IPATH_CREG_OFFSET(RxPKeyMismatchCnt),
- .cr_errrcvflowctrlcnt = IPATH_CREG_OFFSET(RxFlowCtrlErrCnt),
- .cr_err_rlencnt = IPATH_CREG_OFFSET(RxLenErrCnt),
- .cr_errslencnt = IPATH_CREG_OFFSET(TxLenErrCnt),
- .cr_errtidfull = IPATH_CREG_OFFSET(RxTIDFullErrCnt),
- .cr_errtidvalid = IPATH_CREG_OFFSET(RxTIDValidErrCnt),
- .cr_errvcrccnt = IPATH_CREG_OFFSET(RxVCRCErrCnt),
- .cr_ibstatuschange = IPATH_CREG_OFFSET(IBStatusChangeCnt),
- /* calc from Reg_CounterRegBase + offset */
- .cr_intcnt = IPATH_CREG_OFFSET(LBIntCnt),
- .cr_invalidrlencnt = IPATH_CREG_OFFSET(RxMaxMinLenErrCnt),
- .cr_invalidslencnt = IPATH_CREG_OFFSET(TxMaxMinLenErrCnt),
- .cr_lbflowstallcnt = IPATH_CREG_OFFSET(LBFlowStallCnt),
- .cr_pktrcvcnt = IPATH_CREG_OFFSET(RxDataPktCnt),
- .cr_pktrcvflowctrlcnt = IPATH_CREG_OFFSET(RxFlowPktCnt),
- .cr_pktsendcnt = IPATH_CREG_OFFSET(TxDataPktCnt),
- .cr_pktsendflowcnt = IPATH_CREG_OFFSET(TxFlowPktCnt),
- .cr_portovflcnt = IPATH_CREG_OFFSET(RxP0HdrEgrOvflCnt),
- .cr_rcvebpcnt = IPATH_CREG_OFFSET(RxEBPCnt),
- .cr_rcvovflcnt = IPATH_CREG_OFFSET(RxBufOvflCnt),
- .cr_senddropped = IPATH_CREG_OFFSET(TxDroppedPktCnt),
- .cr_sendstallcnt = IPATH_CREG_OFFSET(TxFlowStallCnt),
- .cr_sendunderruncnt = IPATH_CREG_OFFSET(TxUnderrunCnt),
- .cr_wordrcvcnt = IPATH_CREG_OFFSET(RxDwordCnt),
- .cr_wordsendcnt = IPATH_CREG_OFFSET(TxDwordCnt),
- .cr_unsupvlcnt = IPATH_CREG_OFFSET(TxUnsupVLErrCnt),
- .cr_rxdroppktcnt = IPATH_CREG_OFFSET(RxDroppedPktCnt),
- .cr_iblinkerrrecovcnt = IPATH_CREG_OFFSET(IBLinkErrRecoveryCnt),
- .cr_iblinkdowncnt = IPATH_CREG_OFFSET(IBLinkDownedCnt),
- .cr_ibsymbolerrcnt = IPATH_CREG_OFFSET(IBSymbolErrCnt)
-};
-
-/* kr_intstatus, kr_intclear, kr_intmask bits */
-#define INFINIPATH_I_RCVURG_MASK ((1U<<9)-1)
-#define INFINIPATH_I_RCVURG_SHIFT 0
-#define INFINIPATH_I_RCVAVAIL_MASK ((1U<<9)-1)
-#define INFINIPATH_I_RCVAVAIL_SHIFT 12
-
-/* kr_hwerrclear, kr_hwerrmask, kr_hwerrstatus, bits */
-#define INFINIPATH_HWE_HTCMEMPARITYERR_SHIFT 0
-#define INFINIPATH_HWE_HTCMEMPARITYERR_MASK 0x3FFFFFULL
-#define INFINIPATH_HWE_HTCLNKABYTE0CRCERR 0x0000000000800000ULL
-#define INFINIPATH_HWE_HTCLNKABYTE1CRCERR 0x0000000001000000ULL
-#define INFINIPATH_HWE_HTCLNKBBYTE0CRCERR 0x0000000002000000ULL
-#define INFINIPATH_HWE_HTCLNKBBYTE1CRCERR 0x0000000004000000ULL
-#define INFINIPATH_HWE_HTCMISCERR4 0x0000000008000000ULL
-#define INFINIPATH_HWE_HTCMISCERR5 0x0000000010000000ULL
-#define INFINIPATH_HWE_HTCMISCERR6 0x0000000020000000ULL
-#define INFINIPATH_HWE_HTCMISCERR7 0x0000000040000000ULL
-#define INFINIPATH_HWE_HTCBUSTREQPARITYERR 0x0000000080000000ULL
-#define INFINIPATH_HWE_HTCBUSTRESPPARITYERR 0x0000000100000000ULL
-#define INFINIPATH_HWE_HTCBUSIREQPARITYERR 0x0000000200000000ULL
-#define INFINIPATH_HWE_COREPLL_FBSLIP 0x0080000000000000ULL
-#define INFINIPATH_HWE_COREPLL_RFSLIP 0x0100000000000000ULL
-#define INFINIPATH_HWE_HTBPLL_FBSLIP 0x0200000000000000ULL
-#define INFINIPATH_HWE_HTBPLL_RFSLIP 0x0400000000000000ULL
-#define INFINIPATH_HWE_HTAPLL_FBSLIP 0x0800000000000000ULL
-#define INFINIPATH_HWE_HTAPLL_RFSLIP 0x1000000000000000ULL
-#define INFINIPATH_HWE_SERDESPLLFAILED 0x2000000000000000ULL
-
-#define IBA6110_IBCS_LINKTRAININGSTATE_MASK 0xf
-#define IBA6110_IBCS_LINKSTATE_SHIFT 4
-
-/* kr_extstatus bits */
-#define INFINIPATH_EXTS_FREQSEL 0x2
-#define INFINIPATH_EXTS_SERDESSEL 0x4
-#define INFINIPATH_EXTS_MEMBIST_ENDTEST 0x0000000000004000
-#define INFINIPATH_EXTS_MEMBIST_CORRECT 0x0000000000008000
-
-
-/* TID entries (memory), HT-only */
-#define INFINIPATH_RT_ADDR_MASK 0xFFFFFFFFFFULL /* 40 bits valid */
-#define INFINIPATH_RT_VALID 0x8000000000000000ULL
-#define INFINIPATH_RT_ADDR_SHIFT 0
-#define INFINIPATH_RT_BUFSIZE_MASK 0x3FFFULL
-#define INFINIPATH_RT_BUFSIZE_SHIFT 48
-
-#define INFINIPATH_R_INTRAVAIL_SHIFT 16
-#define INFINIPATH_R_TAILUPD_SHIFT 31
-
-/* kr_xgxsconfig bits */
-#define INFINIPATH_XGXS_RESET 0x7ULL
-
-/*
- * masks and bits that are different in different chips, or present only
- * in one
- */
-static const ipath_err_t infinipath_hwe_htcmemparityerr_mask =
- INFINIPATH_HWE_HTCMEMPARITYERR_MASK;
-static const ipath_err_t infinipath_hwe_htcmemparityerr_shift =
- INFINIPATH_HWE_HTCMEMPARITYERR_SHIFT;
-
-static const ipath_err_t infinipath_hwe_htclnkabyte0crcerr =
- INFINIPATH_HWE_HTCLNKABYTE0CRCERR;
-static const ipath_err_t infinipath_hwe_htclnkabyte1crcerr =
- INFINIPATH_HWE_HTCLNKABYTE1CRCERR;
-static const ipath_err_t infinipath_hwe_htclnkbbyte0crcerr =
- INFINIPATH_HWE_HTCLNKBBYTE0CRCERR;
-static const ipath_err_t infinipath_hwe_htclnkbbyte1crcerr =
- INFINIPATH_HWE_HTCLNKBBYTE1CRCERR;
-
-#define _IPATH_GPIO_SDA_NUM 1
-#define _IPATH_GPIO_SCL_NUM 0
-
-#define IPATH_GPIO_SDA \
- (1ULL << (_IPATH_GPIO_SDA_NUM+INFINIPATH_EXTC_GPIOOE_SHIFT))
-#define IPATH_GPIO_SCL \
- (1ULL << (_IPATH_GPIO_SCL_NUM+INFINIPATH_EXTC_GPIOOE_SHIFT))
-
-/* keep the code below somewhat more readable; not used elsewhere */
-#define _IPATH_HTLINK0_CRCBITS (infinipath_hwe_htclnkabyte0crcerr | \
- infinipath_hwe_htclnkabyte1crcerr)
-#define _IPATH_HTLINK1_CRCBITS (infinipath_hwe_htclnkbbyte0crcerr | \
- infinipath_hwe_htclnkbbyte1crcerr)
-#define _IPATH_HTLANE0_CRCBITS (infinipath_hwe_htclnkabyte0crcerr | \
- infinipath_hwe_htclnkbbyte0crcerr)
-#define _IPATH_HTLANE1_CRCBITS (infinipath_hwe_htclnkabyte1crcerr | \
- infinipath_hwe_htclnkbbyte1crcerr)
-
-static void hwerr_crcbits(struct ipath_devdata *dd, ipath_err_t hwerrs,
- char *msg, size_t msgl)
-{
- char bitsmsg[64];
- ipath_err_t crcbits = hwerrs &
- (_IPATH_HTLINK0_CRCBITS | _IPATH_HTLINK1_CRCBITS);
- /* don't check if 8bit HT */
- if (dd->ipath_flags & IPATH_8BIT_IN_HT0)
- crcbits &= ~infinipath_hwe_htclnkabyte1crcerr;
- /* don't check if 8bit HT */
- if (dd->ipath_flags & IPATH_8BIT_IN_HT1)
- crcbits &= ~infinipath_hwe_htclnkbbyte1crcerr;
- /*
- * we'll want to ignore link errors on link that is
- * not in use, if any. For now, complain about both
- */
- if (crcbits) {
- u16 ctrl0, ctrl1;
- snprintf(bitsmsg, sizeof bitsmsg,
- "[HT%s lane %s CRC (%llx); powercycle to completely clear]",
- !(crcbits & _IPATH_HTLINK1_CRCBITS) ?
- "0 (A)" : (!(crcbits & _IPATH_HTLINK0_CRCBITS)
- ? "1 (B)" : "0+1 (A+B)"),
- !(crcbits & _IPATH_HTLANE1_CRCBITS) ? "0"
- : (!(crcbits & _IPATH_HTLANE0_CRCBITS) ? "1" :
- "0+1"), (unsigned long long) crcbits);
- strlcat(msg, bitsmsg, msgl);
-
- /*
- * print extra info for debugging. slave/primary
- * config word 4, 8 (link control 0, 1)
- */
-
- if (pci_read_config_word(dd->pcidev,
- dd->ipath_ht_slave_off + 0x4,
- &ctrl0))
- dev_info(&dd->pcidev->dev, "Couldn't read "
- "linkctrl0 of slave/primary "
- "config block\n");
- else if (!(ctrl0 & 1 << 6))
- /* not if EOC bit set */
- ipath_dbg("HT linkctrl0 0x%x%s%s\n", ctrl0,
- ((ctrl0 >> 8) & 7) ? " CRC" : "",
- ((ctrl0 >> 4) & 1) ? "linkfail" :
- "");
- if (pci_read_config_word(dd->pcidev,
- dd->ipath_ht_slave_off + 0x8,
- &ctrl1))
- dev_info(&dd->pcidev->dev, "Couldn't read "
- "linkctrl1 of slave/primary "
- "config block\n");
- else if (!(ctrl1 & 1 << 6))
- /* not if EOC bit set */
- ipath_dbg("HT linkctrl1 0x%x%s%s\n", ctrl1,
- ((ctrl1 >> 8) & 7) ? " CRC" : "",
- ((ctrl1 >> 4) & 1) ? "linkfail" :
- "");
-
- /* disable until driver reloaded */
- dd->ipath_hwerrmask &= ~crcbits;
- ipath_write_kreg(dd, dd->ipath_kregs->kr_hwerrmask,
- dd->ipath_hwerrmask);
- ipath_dbg("HT crc errs: %s\n", msg);
- } else
- ipath_dbg("ignoring HT crc errors 0x%llx, "
- "not in use\n", (unsigned long long)
- (hwerrs & (_IPATH_HTLINK0_CRCBITS |
- _IPATH_HTLINK1_CRCBITS)));
-}
-
-/* 6110 specific hardware errors... */
-static const struct ipath_hwerror_msgs ipath_6110_hwerror_msgs[] = {
- INFINIPATH_HWE_MSG(HTCBUSIREQPARITYERR, "HTC Ireq Parity"),
- INFINIPATH_HWE_MSG(HTCBUSTREQPARITYERR, "HTC Treq Parity"),
- INFINIPATH_HWE_MSG(HTCBUSTRESPPARITYERR, "HTC Tresp Parity"),
- INFINIPATH_HWE_MSG(HTCMISCERR5, "HT core Misc5"),
- INFINIPATH_HWE_MSG(HTCMISCERR6, "HT core Misc6"),
- INFINIPATH_HWE_MSG(HTCMISCERR7, "HT core Misc7"),
- INFINIPATH_HWE_MSG(RXDSYNCMEMPARITYERR, "Rx Dsync"),
- INFINIPATH_HWE_MSG(SERDESPLLFAILED, "SerDes PLL"),
-};
-
-#define TXE_PIO_PARITY ((INFINIPATH_HWE_TXEMEMPARITYERR_PIOBUF | \
- INFINIPATH_HWE_TXEMEMPARITYERR_PIOPBC) \
- << INFINIPATH_HWE_TXEMEMPARITYERR_SHIFT)
-#define RXE_EAGER_PARITY (INFINIPATH_HWE_RXEMEMPARITYERR_EAGERTID \
- << INFINIPATH_HWE_RXEMEMPARITYERR_SHIFT)
-
-static void ipath_ht_txe_recover(struct ipath_devdata *dd)
-{
- ++ipath_stats.sps_txeparity;
- dev_info(&dd->pcidev->dev,
- "Recovering from TXE PIO parity error\n");
-}
-
-
-/**
- * ipath_ht_handle_hwerrors - display hardware errors.
- * @dd: the infinipath device
- * @msg: the output buffer
- * @msgl: the size of the output buffer
- *
- * Use same msg buffer as regular errors to avoid excessive stack
- * use. Most hardware errors are catastrophic, but for right now,
- * we'll print them and continue. We reuse the same message buffer as
- * ipath_handle_errors() to avoid excessive stack usage.
- */
-static void ipath_ht_handle_hwerrors(struct ipath_devdata *dd, char *msg,
- size_t msgl)
-{
- ipath_err_t hwerrs;
- u32 bits, ctrl;
- int isfatal = 0;
- char bitsmsg[64];
- int log_idx;
-
- hwerrs = ipath_read_kreg64(dd, dd->ipath_kregs->kr_hwerrstatus);
-
- if (!hwerrs) {
- ipath_cdbg(VERBOSE, "Called but no hardware errors set\n");
- /*
- * better than printing cofusing messages
- * This seems to be related to clearing the crc error, or
- * the pll error during init.
- */
- goto bail;
- } else if (hwerrs == -1LL) {
- ipath_dev_err(dd, "Read of hardware error status failed "
- "(all bits set); ignoring\n");
- goto bail;
- }
- ipath_stats.sps_hwerrs++;
-
- /* Always clear the error status register, except MEMBISTFAIL,
- * regardless of whether we continue or stop using the chip.
- * We want that set so we know it failed, even across driver reload.
- * We'll still ignore it in the hwerrmask. We do this partly for
- * diagnostics, but also for support */
- ipath_write_kreg(dd, dd->ipath_kregs->kr_hwerrclear,
- hwerrs&~INFINIPATH_HWE_MEMBISTFAILED);
-
- hwerrs &= dd->ipath_hwerrmask;
-
- /* We log some errors to EEPROM, check if we have any of those. */
- for (log_idx = 0; log_idx < IPATH_EEP_LOG_CNT; ++log_idx)
- if (hwerrs & dd->ipath_eep_st_masks[log_idx].hwerrs_to_log)
- ipath_inc_eeprom_err(dd, log_idx, 1);
-
- /*
- * make sure we get this much out, unless told to be quiet,
- * it's a parity error we may recover from,
- * or it's occurred within the last 5 seconds
- */
- if ((hwerrs & ~(dd->ipath_lasthwerror | TXE_PIO_PARITY |
- RXE_EAGER_PARITY)) ||
- (ipath_debug & __IPATH_VERBDBG))
- dev_info(&dd->pcidev->dev, "Hardware error: hwerr=0x%llx "
- "(cleared)\n", (unsigned long long) hwerrs);
- dd->ipath_lasthwerror |= hwerrs;
-
- if (hwerrs & ~dd->ipath_hwe_bitsextant)
- ipath_dev_err(dd, "hwerror interrupt with unknown errors "
- "%llx set\n", (unsigned long long)
- (hwerrs & ~dd->ipath_hwe_bitsextant));
-
- ctrl = ipath_read_kreg32(dd, dd->ipath_kregs->kr_control);
- if ((ctrl & INFINIPATH_C_FREEZEMODE) && !ipath_diag_inuse) {
- /*
- * parity errors in send memory are recoverable,
- * just cancel the send (if indicated in * sendbuffererror),
- * count the occurrence, unfreeze (if no other handled
- * hardware error bits are set), and continue. They can
- * occur if a processor speculative read is done to the PIO
- * buffer while we are sending a packet, for example.
- */
- if (hwerrs & TXE_PIO_PARITY) {
- ipath_ht_txe_recover(dd);
- hwerrs &= ~TXE_PIO_PARITY;
- }
-
- if (!hwerrs) {
- ipath_dbg("Clearing freezemode on ignored or "
- "recovered hardware error\n");
- ipath_clear_freeze(dd);
- }
- }
-
- *msg = '\0';
-
- /*
- * may someday want to decode into which bits are which
- * functional area for parity errors, etc.
- */
- if (hwerrs & (infinipath_hwe_htcmemparityerr_mask
- << INFINIPATH_HWE_HTCMEMPARITYERR_SHIFT)) {
- bits = (u32) ((hwerrs >>
- INFINIPATH_HWE_HTCMEMPARITYERR_SHIFT) &
- INFINIPATH_HWE_HTCMEMPARITYERR_MASK);
- snprintf(bitsmsg, sizeof bitsmsg, "[HTC Parity Errs %x] ",
- bits);
- strlcat(msg, bitsmsg, msgl);
- }
-
- ipath_format_hwerrors(hwerrs,
- ipath_6110_hwerror_msgs,
- ARRAY_SIZE(ipath_6110_hwerror_msgs),
- msg, msgl);
-
- if (hwerrs & (_IPATH_HTLINK0_CRCBITS | _IPATH_HTLINK1_CRCBITS))
- hwerr_crcbits(dd, hwerrs, msg, msgl);
-
- if (hwerrs & INFINIPATH_HWE_MEMBISTFAILED) {
- strlcat(msg, "[Memory BIST test failed, InfiniPath hardware unusable]",
- msgl);
- /* ignore from now on, so disable until driver reloaded */
- dd->ipath_hwerrmask &= ~INFINIPATH_HWE_MEMBISTFAILED;
- ipath_write_kreg(dd, dd->ipath_kregs->kr_hwerrmask,
- dd->ipath_hwerrmask);
- }
-#define _IPATH_PLL_FAIL (INFINIPATH_HWE_COREPLL_FBSLIP | \
- INFINIPATH_HWE_COREPLL_RFSLIP | \
- INFINIPATH_HWE_HTBPLL_FBSLIP | \
- INFINIPATH_HWE_HTBPLL_RFSLIP | \
- INFINIPATH_HWE_HTAPLL_FBSLIP | \
- INFINIPATH_HWE_HTAPLL_RFSLIP)
-
- if (hwerrs & _IPATH_PLL_FAIL) {
- snprintf(bitsmsg, sizeof bitsmsg,
- "[PLL failed (%llx), InfiniPath hardware unusable]",
- (unsigned long long) (hwerrs & _IPATH_PLL_FAIL));
- strlcat(msg, bitsmsg, msgl);
- /* ignore from now on, so disable until driver reloaded */
- dd->ipath_hwerrmask &= ~(hwerrs & _IPATH_PLL_FAIL);
- ipath_write_kreg(dd, dd->ipath_kregs->kr_hwerrmask,
- dd->ipath_hwerrmask);
- }
-
- if (hwerrs & INFINIPATH_HWE_SERDESPLLFAILED) {
- /*
- * If it occurs, it is left masked since the eternal
- * interface is unused
- */
- dd->ipath_hwerrmask &= ~INFINIPATH_HWE_SERDESPLLFAILED;
- ipath_write_kreg(dd, dd->ipath_kregs->kr_hwerrmask,
- dd->ipath_hwerrmask);
- }
-
- if (hwerrs) {
- /*
- * if any set that we aren't ignoring; only
- * make the complaint once, in case it's stuck
- * or recurring, and we get here multiple
- * times.
- * force link down, so switch knows, and
- * LEDs are turned off
- */
- if (dd->ipath_flags & IPATH_INITTED) {
- ipath_set_linkstate(dd, IPATH_IB_LINKDOWN);
- ipath_setup_ht_setextled(dd,
- INFINIPATH_IBCS_L_STATE_DOWN,
- INFINIPATH_IBCS_LT_STATE_DISABLED);
- ipath_dev_err(dd, "Fatal Hardware Error (freeze "
- "mode), no longer usable, SN %.16s\n",
- dd->ipath_serial);
- isfatal = 1;
- }
- *dd->ipath_statusp &= ~IPATH_STATUS_IB_READY;
- /* mark as having had error */
- *dd->ipath_statusp |= IPATH_STATUS_HWERROR;
- /*
- * mark as not usable, at a minimum until driver
- * is reloaded, probably until reboot, since no
- * other reset is possible.
- */
- dd->ipath_flags &= ~IPATH_INITTED;
- }
- else
- *msg = 0; /* recovered from all of them */
- if (*msg)
- ipath_dev_err(dd, "%s hardware error\n", msg);
- if (isfatal && !ipath_diag_inuse && dd->ipath_freezemsg)
- /*
- * for status file; if no trailing brace is copied,
- * we'll know it was truncated.
- */
- snprintf(dd->ipath_freezemsg,
- dd->ipath_freezelen, "{%s}", msg);
-
-bail:;
-}
-
-/**
- * ipath_ht_boardname - fill in the board name
- * @dd: the infinipath device
- * @name: the output buffer
- * @namelen: the size of the output buffer
- *
- * fill in the board name, based on the board revision register
- */
-static int ipath_ht_boardname(struct ipath_devdata *dd, char *name,
- size_t namelen)
-{
- char *n = NULL;
- u8 boardrev = dd->ipath_boardrev;
- int ret = 0;
-
- switch (boardrev) {
- case 5:
- /*
- * original production board; two production levels, with
- * different serial number ranges. See ipath_ht_early_init() for
- * case where we enable IPATH_GPIO_INTR for later serial # range.
- * Original 112* serial number is no longer supported.
- */
- n = "InfiniPath_QHT7040";
- break;
- case 7:
- /* small form factor production board */
- n = "InfiniPath_QHT7140";
- break;
- default: /* don't know, just print the number */
- ipath_dev_err(dd, "Don't yet know about board "
- "with ID %u\n", boardrev);
- snprintf(name, namelen, "Unknown_InfiniPath_QHT7xxx_%u",
- boardrev);
- break;
- }
- if (n)
- snprintf(name, namelen, "%s", n);
-
- if (ret) {
- ipath_dev_err(dd, "Unsupported InfiniPath board %s!\n", name);
- goto bail;
- }
- if (dd->ipath_majrev != 3 || (dd->ipath_minrev < 2 ||
- dd->ipath_minrev > 4)) {
- /*
- * This version of the driver only supports Rev 3.2 - 3.4
- */
- ipath_dev_err(dd,
- "Unsupported InfiniPath hardware revision %u.%u!\n",
- dd->ipath_majrev, dd->ipath_minrev);
- ret = 1;
- goto bail;
- }
- /*
- * pkt/word counters are 32 bit, and therefore wrap fast enough
- * that we snapshot them from a timer, and maintain 64 bit shadow
- * copies
- */
- dd->ipath_flags |= IPATH_32BITCOUNTERS;
- dd->ipath_flags |= IPATH_GPIO_INTR;
- if (dd->ipath_lbus_speed != 800)
- ipath_dev_err(dd,
- "Incorrectly configured for HT @ %uMHz\n",
- dd->ipath_lbus_speed);
-
- /*
- * set here, not in ipath_init_*_funcs because we have to do
- * it after we can read chip registers.
- */
- dd->ipath_ureg_align =
- ipath_read_kreg32(dd, dd->ipath_kregs->kr_pagealign);
-
-bail:
- return ret;
-}
-
-static void ipath_check_htlink(struct ipath_devdata *dd)
-{
- u8 linkerr, link_off, i;
-
- for (i = 0; i < 2; i++) {
- link_off = dd->ipath_ht_slave_off + i * 4 + 0xd;
- if (pci_read_config_byte(dd->pcidev, link_off, &linkerr))
- dev_info(&dd->pcidev->dev, "Couldn't read "
- "linkerror%d of HT slave/primary block\n",
- i);
- else if (linkerr & 0xf0) {
- ipath_cdbg(VERBOSE, "HT linkerr%d bits 0x%x set, "
- "clearing\n", linkerr >> 4, i);
- /*
- * writing the linkerr bits that are set should
- * clear them
- */
- if (pci_write_config_byte(dd->pcidev, link_off,
- linkerr))
- ipath_dbg("Failed write to clear HT "
- "linkerror%d\n", i);
- if (pci_read_config_byte(dd->pcidev, link_off,
- &linkerr))
- dev_info(&dd->pcidev->dev,
- "Couldn't reread linkerror%d of "
- "HT slave/primary block\n", i);
- else if (linkerr & 0xf0)
- dev_info(&dd->pcidev->dev,
- "HT linkerror%d bits 0x%x "
- "couldn't be cleared\n",
- i, linkerr >> 4);
- }
- }
-}
-
-static int ipath_setup_ht_reset(struct ipath_devdata *dd)
-{
- ipath_dbg("No reset possible for this InfiniPath hardware\n");
- return 0;
-}
-
-#define HT_INTR_DISC_CONFIG 0x80 /* HT interrupt and discovery cap */
-#define HT_INTR_REG_INDEX 2 /* intconfig requires indirect accesses */
-
-/*
- * Bits 13-15 of command==0 is slave/primary block. Clear any HT CRC
- * errors. We only bother to do this at load time, because it's OK if
- * it happened before we were loaded (first time after boot/reset),
- * but any time after that, it's fatal anyway. Also need to not check
- * for upper byte errors if we are in 8 bit mode, so figure out
- * our width. For now, at least, also complain if it's 8 bit.
- */
-static void slave_or_pri_blk(struct ipath_devdata *dd, struct pci_dev *pdev,
- int pos, u8 cap_type)
-{
- u8 linkwidth = 0, linkerr, link_a_b_off, link_off;
- u16 linkctrl = 0;
- int i;
-
- dd->ipath_ht_slave_off = pos;
- /* command word, master_host bit */
- /* master host || slave */
- if ((cap_type >> 2) & 1)
- link_a_b_off = 4;
- else
- link_a_b_off = 0;
- ipath_cdbg(VERBOSE, "HT%u (Link %c) connected to processor\n",
- link_a_b_off ? 1 : 0,
- link_a_b_off ? 'B' : 'A');
-
- link_a_b_off += pos;
-
- /*
- * check both link control registers; clear both HT CRC sets if
- * necessary.
- */
- for (i = 0; i < 2; i++) {
- link_off = pos + i * 4 + 0x4;
- if (pci_read_config_word(pdev, link_off, &linkctrl))
- ipath_dev_err(dd, "Couldn't read HT link control%d "
- "register\n", i);
- else if (linkctrl & (0xf << 8)) {
- ipath_cdbg(VERBOSE, "Clear linkctrl%d CRC Error "
- "bits %x\n", i, linkctrl & (0xf << 8));
- /*
- * now write them back to clear the error.
- */
- pci_write_config_word(pdev, link_off,
- linkctrl & (0xf << 8));
- }
- }
-
- /*
- * As with HT CRC bits, same for protocol errors that might occur
- * during boot.
- */
- for (i = 0; i < 2; i++) {
- link_off = pos + i * 4 + 0xd;
- if (pci_read_config_byte(pdev, link_off, &linkerr))
- dev_info(&pdev->dev, "Couldn't read linkerror%d "
- "of HT slave/primary block\n", i);
- else if (linkerr & 0xf0) {
- ipath_cdbg(VERBOSE, "HT linkerr%d bits 0x%x set, "
- "clearing\n", linkerr >> 4, i);
- /*
- * writing the linkerr bits that are set will clear
- * them
- */
- if (pci_write_config_byte
- (pdev, link_off, linkerr))
- ipath_dbg("Failed write to clear HT "
- "linkerror%d\n", i);
- if (pci_read_config_byte(pdev, link_off, &linkerr))
- dev_info(&pdev->dev, "Couldn't reread "
- "linkerror%d of HT slave/primary "
- "block\n", i);
- else if (linkerr & 0xf0)
- dev_info(&pdev->dev, "HT linkerror%d bits "
- "0x%x couldn't be cleared\n",
- i, linkerr >> 4);
- }
- }
-
- /*
- * this is just for our link to the host, not devices connected
- * through tunnel.
- */
-
- if (pci_read_config_byte(pdev, link_a_b_off + 7, &linkwidth))
- ipath_dev_err(dd, "Couldn't read HT link width "
- "config register\n");
- else {
- u32 width;
- switch (linkwidth & 7) {
- case 5:
- width = 4;
- break;
- case 4:
- width = 2;
- break;
- case 3:
- width = 32;
- break;
- case 1:
- width = 16;
- break;
- case 0:
- default: /* if wrong, assume 8 bit */
- width = 8;
- break;
- }
-
- dd->ipath_lbus_width = width;
-
- if (linkwidth != 0x11) {
- ipath_dev_err(dd, "Not configured for 16 bit HT "
- "(%x)\n", linkwidth);
- if (!(linkwidth & 0xf)) {
- ipath_dbg("Will ignore HT lane1 errors\n");
- dd->ipath_flags |= IPATH_8BIT_IN_HT0;
- }
- }
- }
-
- /*
- * this is just for our link to the host, not devices connected
- * through tunnel.
- */
- if (pci_read_config_byte(pdev, link_a_b_off + 0xd, &linkwidth))
- ipath_dev_err(dd, "Couldn't read HT link frequency "
- "config register\n");
- else {
- u32 speed;
- switch (linkwidth & 0xf) {
- case 6:
- speed = 1000;
- break;
- case 5:
- speed = 800;
- break;
- case 4:
- speed = 600;
- break;
- case 3:
- speed = 500;
- break;
- case 2:
- speed = 400;
- break;
- case 1:
- speed = 300;
- break;
- default:
- /*
- * assume reserved and vendor-specific are 200...
- */
- case 0:
- speed = 200;
- break;
- }
- dd->ipath_lbus_speed = speed;
- }
-
- snprintf(dd->ipath_lbus_info, sizeof(dd->ipath_lbus_info),
- "HyperTransport,%uMHz,x%u\n",
- dd->ipath_lbus_speed,
- dd->ipath_lbus_width);
-}
-
-static int ipath_ht_intconfig(struct ipath_devdata *dd)
-{
- int ret;
-
- if (dd->ipath_intconfig) {
- ipath_write_kreg(dd, dd->ipath_kregs->kr_interruptconfig,
- dd->ipath_intconfig); /* interrupt address */
- ret = 0;
- } else {
- ipath_dev_err(dd, "No interrupts enabled, couldn't setup "
- "interrupt address\n");
- ret = -EINVAL;
- }
-
- return ret;
-}
-
-static void ipath_ht_irq_update(struct pci_dev *dev, int irq,
- struct ht_irq_msg *msg)
-{
- struct ipath_devdata *dd = pci_get_drvdata(dev);
- u64 prev_intconfig = dd->ipath_intconfig;
-
- dd->ipath_intconfig = msg->address_lo;
- dd->ipath_intconfig |= ((u64) msg->address_hi) << 32;
-
- /*
- * If the previous value of dd->ipath_intconfig is zero, we're
- * getting configured for the first time, and must not program the
- * intconfig register here (it will be programmed later, when the
- * hardware is ready). Otherwise, we should.
- */
- if (prev_intconfig)
- ipath_ht_intconfig(dd);
-}
-
-/**
- * ipath_setup_ht_config - setup the interruptconfig register
- * @dd: the infinipath device
- * @pdev: the PCI device
- *
- * setup the interruptconfig register from the HT config info.
- * Also clear CRC errors in HT linkcontrol, if necessary.
- * This is done only for the real hardware. It is done before
- * chip address space is initted, so can't touch infinipath registers
- */
-static int ipath_setup_ht_config(struct ipath_devdata *dd,
- struct pci_dev *pdev)
-{
- int pos, ret;
-
- ret = __ht_create_irq(pdev, 0, ipath_ht_irq_update);
- if (ret < 0) {
- ipath_dev_err(dd, "Couldn't create interrupt handler: "
- "err %d\n", ret);
- goto bail;
- }
- dd->ipath_irq = ret;
- ret = 0;
-
- /*
- * Handle clearing CRC errors in linkctrl register if necessary. We
- * do this early, before we ever enable errors or hardware errors,
- * mostly to avoid causing the chip to enter freeze mode.
- */
- pos = pci_find_capability(pdev, PCI_CAP_ID_HT);
- if (!pos) {
- ipath_dev_err(dd, "Couldn't find HyperTransport "
- "capability; no interrupts\n");
- ret = -ENODEV;
- goto bail;
- }
- do {
- u8 cap_type;
-
- /*
- * The HT capability type byte is 3 bytes after the
- * capability byte.
- */
- if (pci_read_config_byte(pdev, pos + 3, &cap_type)) {
- dev_info(&pdev->dev, "Couldn't read config "
- "command @ %d\n", pos);
- continue;
- }
- if (!(cap_type & 0xE0))
- slave_or_pri_blk(dd, pdev, pos, cap_type);
- } while ((pos = pci_find_next_capability(pdev, pos,
- PCI_CAP_ID_HT)));
-
- dd->ipath_flags |= IPATH_SWAP_PIOBUFS;
-
-bail:
- return ret;
-}
-
-/**
- * ipath_setup_ht_cleanup - clean up any per-chip chip-specific stuff
- * @dd: the infinipath device
- *
- * Called during driver unload.
- * This is currently a nop for the HT chip, not for all chips
- */
-static void ipath_setup_ht_cleanup(struct ipath_devdata *dd)
-{
-}
-
-/**
- * ipath_setup_ht_setextled - set the state of the two external LEDs
- * @dd: the infinipath device
- * @lst: the L state
- * @ltst: the LT state
- *
- * Set the state of the two external LEDs, to indicate physical and
- * logical state of IB link. For this chip (at least with recommended
- * board pinouts), LED1 is Green (physical state), and LED2 is Yellow
- * (logical state)
- *
- * Note: We try to match the Mellanox HCA LED behavior as best
- * we can. Green indicates physical link state is OK (something is
- * plugged in, and we can train).
- * Amber indicates the link is logically up (ACTIVE).
- * Mellanox further blinks the amber LED to indicate data packet
- * activity, but we have no hardware support for that, so it would
- * require waking up every 10-20 msecs and checking the counters
- * on the chip, and then turning the LED off if appropriate. That's
- * visible overhead, so not something we will do.
- *
- */
-static void ipath_setup_ht_setextled(struct ipath_devdata *dd,
- u64 lst, u64 ltst)
-{
- u64 extctl;
- unsigned long flags = 0;
-
- /* the diags use the LED to indicate diag info, so we leave
- * the external LED alone when the diags are running */
- if (ipath_diag_inuse)
- return;
-
- /* Allow override of LED display for, e.g. Locating system in rack */
- if (dd->ipath_led_override) {
- ltst = (dd->ipath_led_override & IPATH_LED_PHYS)
- ? INFINIPATH_IBCS_LT_STATE_LINKUP
- : INFINIPATH_IBCS_LT_STATE_DISABLED;
- lst = (dd->ipath_led_override & IPATH_LED_LOG)
- ? INFINIPATH_IBCS_L_STATE_ACTIVE
- : INFINIPATH_IBCS_L_STATE_DOWN;
- }
-
- spin_lock_irqsave(&dd->ipath_gpio_lock, flags);
- /*
- * start by setting both LED control bits to off, then turn
- * on the appropriate bit(s).
- */
- if (dd->ipath_boardrev == 8) { /* LS/X-1 uses different pins */
- /*
- * major difference is that INFINIPATH_EXTC_LEDGBLERR_OFF
- * is inverted, because it is normally used to indicate
- * a hardware fault at reset, if there were errors
- */
- extctl = (dd->ipath_extctrl & ~INFINIPATH_EXTC_LEDGBLOK_ON)
- | INFINIPATH_EXTC_LEDGBLERR_OFF;
- if (ltst == INFINIPATH_IBCS_LT_STATE_LINKUP)
- extctl &= ~INFINIPATH_EXTC_LEDGBLERR_OFF;
- if (lst == INFINIPATH_IBCS_L_STATE_ACTIVE)
- extctl |= INFINIPATH_EXTC_LEDGBLOK_ON;
- }
- else {
- extctl = dd->ipath_extctrl &
- ~(INFINIPATH_EXTC_LED1PRIPORT_ON |
- INFINIPATH_EXTC_LED2PRIPORT_ON);
- if (ltst == INFINIPATH_IBCS_LT_STATE_LINKUP)
- extctl |= INFINIPATH_EXTC_LED1PRIPORT_ON;
- if (lst == INFINIPATH_IBCS_L_STATE_ACTIVE)
- extctl |= INFINIPATH_EXTC_LED2PRIPORT_ON;
- }
- dd->ipath_extctrl = extctl;
- ipath_write_kreg(dd, dd->ipath_kregs->kr_extctrl, extctl);
- spin_unlock_irqrestore(&dd->ipath_gpio_lock, flags);
-}
-
-static void ipath_init_ht_variables(struct ipath_devdata *dd)
-{
- /*
- * setup the register offsets, since they are different for each
- * chip
- */
- dd->ipath_kregs = &ipath_ht_kregs;
- dd->ipath_cregs = &ipath_ht_cregs;
-
- dd->ipath_gpio_sda_num = _IPATH_GPIO_SDA_NUM;
- dd->ipath_gpio_scl_num = _IPATH_GPIO_SCL_NUM;
- dd->ipath_gpio_sda = IPATH_GPIO_SDA;
- dd->ipath_gpio_scl = IPATH_GPIO_SCL;
-
- /*
- * Fill in data for field-values that change in newer chips.
- * We dynamically specify only the mask for LINKTRAININGSTATE
- * and only the shift for LINKSTATE, as they are the only ones
- * that change. Also precalculate the 3 link states of interest
- * and the combined mask.
- */
- dd->ibcs_ls_shift = IBA6110_IBCS_LINKSTATE_SHIFT;
- dd->ibcs_lts_mask = IBA6110_IBCS_LINKTRAININGSTATE_MASK;
- dd->ibcs_mask = (INFINIPATH_IBCS_LINKSTATE_MASK <<
- dd->ibcs_ls_shift) | dd->ibcs_lts_mask;
- dd->ib_init = (INFINIPATH_IBCS_LT_STATE_LINKUP <<
- INFINIPATH_IBCS_LINKTRAININGSTATE_SHIFT) |
- (INFINIPATH_IBCS_L_STATE_INIT << dd->ibcs_ls_shift);
- dd->ib_arm = (INFINIPATH_IBCS_LT_STATE_LINKUP <<
- INFINIPATH_IBCS_LINKTRAININGSTATE_SHIFT) |
- (INFINIPATH_IBCS_L_STATE_ARM << dd->ibcs_ls_shift);
- dd->ib_active = (INFINIPATH_IBCS_LT_STATE_LINKUP <<
- INFINIPATH_IBCS_LINKTRAININGSTATE_SHIFT) |
- (INFINIPATH_IBCS_L_STATE_ACTIVE << dd->ibcs_ls_shift);
-
- /*
- * Fill in data for ibcc field-values that change in newer chips.
- * We dynamically specify only the mask for LINKINITCMD
- * and only the shift for LINKCMD and MAXPKTLEN, as they are
- * the only ones that change.
- */
- dd->ibcc_lic_mask = INFINIPATH_IBCC_LINKINITCMD_MASK;
- dd->ibcc_lc_shift = INFINIPATH_IBCC_LINKCMD_SHIFT;
- dd->ibcc_mpl_shift = INFINIPATH_IBCC_MAXPKTLEN_SHIFT;
-
- /* Fill in shifts for RcvCtrl. */
- dd->ipath_r_portenable_shift = INFINIPATH_R_PORTENABLE_SHIFT;
- dd->ipath_r_intravail_shift = INFINIPATH_R_INTRAVAIL_SHIFT;
- dd->ipath_r_tailupd_shift = INFINIPATH_R_TAILUPD_SHIFT;
- dd->ipath_r_portcfg_shift = 0; /* Not on IBA6110 */
-
- dd->ipath_i_bitsextant =
- (INFINIPATH_I_RCVURG_MASK << INFINIPATH_I_RCVURG_SHIFT) |
- (INFINIPATH_I_RCVAVAIL_MASK <<
- INFINIPATH_I_RCVAVAIL_SHIFT) |
- INFINIPATH_I_ERROR | INFINIPATH_I_SPIOSENT |
- INFINIPATH_I_SPIOBUFAVAIL | INFINIPATH_I_GPIO;
-
- dd->ipath_e_bitsextant =
- INFINIPATH_E_RFORMATERR | INFINIPATH_E_RVCRC |
- INFINIPATH_E_RICRC | INFINIPATH_E_RMINPKTLEN |
- INFINIPATH_E_RMAXPKTLEN | INFINIPATH_E_RLONGPKTLEN |
- INFINIPATH_E_RSHORTPKTLEN | INFINIPATH_E_RUNEXPCHAR |
- INFINIPATH_E_RUNSUPVL | INFINIPATH_E_REBP |
- INFINIPATH_E_RIBFLOW | INFINIPATH_E_RBADVERSION |
- INFINIPATH_E_RRCVEGRFULL | INFINIPATH_E_RRCVHDRFULL |
- INFINIPATH_E_RBADTID | INFINIPATH_E_RHDRLEN |
- INFINIPATH_E_RHDR | INFINIPATH_E_RIBLOSTLINK |
- INFINIPATH_E_SMINPKTLEN | INFINIPATH_E_SMAXPKTLEN |
- INFINIPATH_E_SUNDERRUN | INFINIPATH_E_SPKTLEN |
- INFINIPATH_E_SDROPPEDSMPPKT | INFINIPATH_E_SDROPPEDDATAPKT |
- INFINIPATH_E_SPIOARMLAUNCH | INFINIPATH_E_SUNEXPERRPKTNUM |
- INFINIPATH_E_SUNSUPVL | INFINIPATH_E_IBSTATUSCHANGED |
- INFINIPATH_E_INVALIDADDR | INFINIPATH_E_RESET |
- INFINIPATH_E_HARDWARE;
-
- dd->ipath_hwe_bitsextant =
- (INFINIPATH_HWE_HTCMEMPARITYERR_MASK <<
- INFINIPATH_HWE_HTCMEMPARITYERR_SHIFT) |
- (INFINIPATH_HWE_TXEMEMPARITYERR_MASK <<
- INFINIPATH_HWE_TXEMEMPARITYERR_SHIFT) |
- (INFINIPATH_HWE_RXEMEMPARITYERR_MASK <<
- INFINIPATH_HWE_RXEMEMPARITYERR_SHIFT) |
- INFINIPATH_HWE_HTCLNKABYTE0CRCERR |
- INFINIPATH_HWE_HTCLNKABYTE1CRCERR |
- INFINIPATH_HWE_HTCLNKBBYTE0CRCERR |
- INFINIPATH_HWE_HTCLNKBBYTE1CRCERR |
- INFINIPATH_HWE_HTCMISCERR4 |
- INFINIPATH_HWE_HTCMISCERR5 | INFINIPATH_HWE_HTCMISCERR6 |
- INFINIPATH_HWE_HTCMISCERR7 |
- INFINIPATH_HWE_HTCBUSTREQPARITYERR |
- INFINIPATH_HWE_HTCBUSTRESPPARITYERR |
- INFINIPATH_HWE_HTCBUSIREQPARITYERR |
- INFINIPATH_HWE_RXDSYNCMEMPARITYERR |
- INFINIPATH_HWE_MEMBISTFAILED |
- INFINIPATH_HWE_COREPLL_FBSLIP |
- INFINIPATH_HWE_COREPLL_RFSLIP |
- INFINIPATH_HWE_HTBPLL_FBSLIP |
- INFINIPATH_HWE_HTBPLL_RFSLIP |
- INFINIPATH_HWE_HTAPLL_FBSLIP |
- INFINIPATH_HWE_HTAPLL_RFSLIP |
- INFINIPATH_HWE_SERDESPLLFAILED |
- INFINIPATH_HWE_IBCBUSTOSPCPARITYERR |
- INFINIPATH_HWE_IBCBUSFRSPCPARITYERR;
-
- dd->ipath_i_rcvavail_mask = INFINIPATH_I_RCVAVAIL_MASK;
- dd->ipath_i_rcvurg_mask = INFINIPATH_I_RCVURG_MASK;
- dd->ipath_i_rcvavail_shift = INFINIPATH_I_RCVAVAIL_SHIFT;
- dd->ipath_i_rcvurg_shift = INFINIPATH_I_RCVURG_SHIFT;
-
- /*
- * EEPROM error log 0 is TXE Parity errors. 1 is RXE Parity.
- * 2 is Some Misc, 3 is reserved for future.
- */
- dd->ipath_eep_st_masks[0].hwerrs_to_log =
- INFINIPATH_HWE_TXEMEMPARITYERR_MASK <<
- INFINIPATH_HWE_TXEMEMPARITYERR_SHIFT;
-
- dd->ipath_eep_st_masks[1].hwerrs_to_log =
- INFINIPATH_HWE_RXEMEMPARITYERR_MASK <<
- INFINIPATH_HWE_RXEMEMPARITYERR_SHIFT;
-
- dd->ipath_eep_st_masks[2].errs_to_log = INFINIPATH_E_RESET;
-
- dd->delay_mult = 2; /* SDR, 4X, can't change */
-
- dd->ipath_link_width_supported = IB_WIDTH_1X | IB_WIDTH_4X;
- dd->ipath_link_speed_supported = IPATH_IB_SDR;
- dd->ipath_link_width_enabled = IB_WIDTH_4X;
- dd->ipath_link_speed_enabled = dd->ipath_link_speed_supported;
- /* these can't change for this chip, so set once */
- dd->ipath_link_width_active = dd->ipath_link_width_enabled;
- dd->ipath_link_speed_active = dd->ipath_link_speed_enabled;
-}
-
-/**
- * ipath_ht_init_hwerrors - enable hardware errors
- * @dd: the infinipath device
- *
- * now that we have finished initializing everything that might reasonably
- * cause a hardware error, and cleared those errors bits as they occur,
- * we can enable hardware errors in the mask (potentially enabling
- * freeze mode), and enable hardware errors as errors (along with
- * everything else) in errormask
- */
-static void ipath_ht_init_hwerrors(struct ipath_devdata *dd)
-{
- ipath_err_t val;
- u64 extsval;
-
- extsval = ipath_read_kreg64(dd, dd->ipath_kregs->kr_extstatus);
-
- if (!(extsval & INFINIPATH_EXTS_MEMBIST_ENDTEST))
- ipath_dev_err(dd, "MemBIST did not complete!\n");
- if (extsval & INFINIPATH_EXTS_MEMBIST_CORRECT)
- ipath_dbg("MemBIST corrected\n");
-
- ipath_check_htlink(dd);
-
- /* barring bugs, all hwerrors become interrupts, which can */
- val = -1LL;
- /* don't look at crc lane1 if 8 bit */
- if (dd->ipath_flags & IPATH_8BIT_IN_HT0)
- val &= ~infinipath_hwe_htclnkabyte1crcerr;
- /* don't look at crc lane1 if 8 bit */
- if (dd->ipath_flags & IPATH_8BIT_IN_HT1)
- val &= ~infinipath_hwe_htclnkbbyte1crcerr;
-
- /*
- * disable RXDSYNCMEMPARITY because external serdes is unused,
- * and therefore the logic will never be used or initialized,
- * and uninitialized state will normally result in this error
- * being asserted. Similarly for the external serdess pll
- * lock signal.
- */
- val &= ~(INFINIPATH_HWE_SERDESPLLFAILED |
- INFINIPATH_HWE_RXDSYNCMEMPARITYERR);
-
- /*
- * Disable MISCERR4 because of an inversion in the HT core
- * logic checking for errors that cause this bit to be set.
- * The errata can also cause the protocol error bit to be set
- * in the HT config space linkerror register(s).
- */
- val &= ~INFINIPATH_HWE_HTCMISCERR4;
-
- /*
- * PLL ignored because unused MDIO interface has a logic problem
- */
- if (dd->ipath_boardrev == 4 || dd->ipath_boardrev == 9)
- val &= ~INFINIPATH_HWE_SERDESPLLFAILED;
- dd->ipath_hwerrmask = val;
-}
-
-
-
-
-/**
- * ipath_ht_bringup_serdes - bring up the serdes
- * @dd: the infinipath device
- */
-static int ipath_ht_bringup_serdes(struct ipath_devdata *dd)
-{
- u64 val, config1;
- int ret = 0, change = 0;
-
- ipath_dbg("Trying to bringup serdes\n");
-
- if (ipath_read_kreg64(dd, dd->ipath_kregs->kr_hwerrstatus) &
- INFINIPATH_HWE_SERDESPLLFAILED)
- {
- ipath_dbg("At start, serdes PLL failed bit set in "
- "hwerrstatus, clearing and continuing\n");
- ipath_write_kreg(dd, dd->ipath_kregs->kr_hwerrclear,
- INFINIPATH_HWE_SERDESPLLFAILED);
- }
-
- val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_serdesconfig0);
- config1 = ipath_read_kreg64(dd, dd->ipath_kregs->kr_serdesconfig1);
-
- ipath_cdbg(VERBOSE, "Initial serdes status is config0=%llx "
- "config1=%llx, sstatus=%llx xgxs %llx\n",
- (unsigned long long) val, (unsigned long long) config1,
- (unsigned long long)
- ipath_read_kreg64(dd, dd->ipath_kregs->kr_serdesstatus),
- (unsigned long long)
- ipath_read_kreg64(dd, dd->ipath_kregs->kr_xgxsconfig));
-
- /* force reset on */
- val |= INFINIPATH_SERDC0_RESET_PLL
- /* | INFINIPATH_SERDC0_RESET_MASK */
- ;
- ipath_write_kreg(dd, dd->ipath_kregs->kr_serdesconfig0, val);
- udelay(15); /* need pll reset set at least for a bit */
-
- if (val & INFINIPATH_SERDC0_RESET_PLL) {
- u64 val2 = val &= ~INFINIPATH_SERDC0_RESET_PLL;
- /* set lane resets, and tx idle, during pll reset */
- val2 |= INFINIPATH_SERDC0_RESET_MASK |
- INFINIPATH_SERDC0_TXIDLE;
- ipath_cdbg(VERBOSE, "Clearing serdes PLL reset (writing "
- "%llx)\n", (unsigned long long) val2);
- ipath_write_kreg(dd, dd->ipath_kregs->kr_serdesconfig0,
- val2);
- /*
- * be sure chip saw it
- */
- val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_scratch);
- /*
- * need pll reset clear at least 11 usec before lane
- * resets cleared; give it a few more
- */
- udelay(15);
- val = val2; /* for check below */
- }
-
- if (val & (INFINIPATH_SERDC0_RESET_PLL |
- INFINIPATH_SERDC0_RESET_MASK |
- INFINIPATH_SERDC0_TXIDLE)) {
- val &= ~(INFINIPATH_SERDC0_RESET_PLL |
- INFINIPATH_SERDC0_RESET_MASK |
- INFINIPATH_SERDC0_TXIDLE);
- /* clear them */
- ipath_write_kreg(dd, dd->ipath_kregs->kr_serdesconfig0,
- val);
- }
-
- val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_xgxsconfig);
- if (val & INFINIPATH_XGXS_RESET) {
- /* normally true after boot */
- val &= ~INFINIPATH_XGXS_RESET;
- change = 1;
- }
- if (((val >> INFINIPATH_XGXS_RX_POL_SHIFT) &
- INFINIPATH_XGXS_RX_POL_MASK) != dd->ipath_rx_pol_inv ) {
- /* need to compensate for Tx inversion in partner */
- val &= ~(INFINIPATH_XGXS_RX_POL_MASK <<
- INFINIPATH_XGXS_RX_POL_SHIFT);
- val |= dd->ipath_rx_pol_inv <<
- INFINIPATH_XGXS_RX_POL_SHIFT;
- change = 1;
- }
- if (change)
- ipath_write_kreg(dd, dd->ipath_kregs->kr_xgxsconfig, val);
-
- val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_serdesconfig0);
-
- /* clear current and de-emphasis bits */
- config1 &= ~0x0ffffffff00ULL;
- /* set current to 20ma */
- config1 |= 0x00000000000ULL;
- /* set de-emphasis to -5.68dB */
- config1 |= 0x0cccc000000ULL;
- ipath_write_kreg(dd, dd->ipath_kregs->kr_serdesconfig1, config1);
-
- ipath_cdbg(VERBOSE, "After setup: serdes status is config0=%llx "
- "config1=%llx, sstatus=%llx xgxs %llx\n",
- (unsigned long long) val, (unsigned long long) config1,
- (unsigned long long)
- ipath_read_kreg64(dd, dd->ipath_kregs->kr_serdesstatus),
- (unsigned long long)
- ipath_read_kreg64(dd, dd->ipath_kregs->kr_xgxsconfig));
-
- return ret; /* for now, say we always succeeded */
-}
-
-/**
- * ipath_ht_quiet_serdes - set serdes to txidle
- * @dd: the infinipath device
- * driver is being unloaded
- */
-static void ipath_ht_quiet_serdes(struct ipath_devdata *dd)
-{
- u64 val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_serdesconfig0);
-
- val |= INFINIPATH_SERDC0_TXIDLE;
- ipath_dbg("Setting TxIdleEn on serdes (config0 = %llx)\n",
- (unsigned long long) val);
- ipath_write_kreg(dd, dd->ipath_kregs->kr_serdesconfig0, val);
-}
-
-/**
- * ipath_pe_put_tid - write a TID in chip
- * @dd: the infinipath device
- * @tidptr: pointer to the expected TID (in chip) to update
- * @tidtype: RCVHQ_RCV_TYPE_EAGER (1) for eager, RCVHQ_RCV_TYPE_EXPECTED (0) for expected
- * @pa: physical address of in memory buffer; ipath_tidinvalid if freeing
- *
- * This exists as a separate routine to allow for special locking etc.
- * It's used for both the full cleanup on exit, as well as the normal
- * setup and teardown.
- */
-static void ipath_ht_put_tid(struct ipath_devdata *dd,
- u64 __iomem *tidptr, u32 type,
- unsigned long pa)
-{
- if (!dd->ipath_kregbase)
- return;
-
- if (pa != dd->ipath_tidinvalid) {
- if (unlikely((pa & ~INFINIPATH_RT_ADDR_MASK))) {
- dev_info(&dd->pcidev->dev,
- "physaddr %lx has more than "
- "40 bits, using only 40!!!\n", pa);
- pa &= INFINIPATH_RT_ADDR_MASK;
- }
- if (type == RCVHQ_RCV_TYPE_EAGER)
- pa |= dd->ipath_tidtemplate;
- else {
- /* in words (fixed, full page). */
- u64 lenvalid = PAGE_SIZE >> 2;
- lenvalid <<= INFINIPATH_RT_BUFSIZE_SHIFT;
- pa |= lenvalid | INFINIPATH_RT_VALID;
- }
- }
-
- writeq(pa, tidptr);
-}
-
-
-/**
- * ipath_ht_clear_tid - clear all TID entries for a port, expected and eager
- * @dd: the infinipath device
- * @port: the port
- *
- * Used from ipath_close(), and at chip initialization.
- */
-static void ipath_ht_clear_tids(struct ipath_devdata *dd, unsigned port)
-{
- u64 __iomem *tidbase;
- int i;
-
- if (!dd->ipath_kregbase)
- return;
-
- ipath_cdbg(VERBOSE, "Invalidate TIDs for port %u\n", port);
-
- /*
- * need to invalidate all of the expected TID entries for this
- * port, so we don't have valid entries that might somehow get
- * used (early in next use of this port, or through some bug)
- */
- tidbase = (u64 __iomem *) ((char __iomem *)(dd->ipath_kregbase) +
- dd->ipath_rcvtidbase +
- port * dd->ipath_rcvtidcnt *
- sizeof(*tidbase));
- for (i = 0; i < dd->ipath_rcvtidcnt; i++)
- ipath_ht_put_tid(dd, &tidbase[i], RCVHQ_RCV_TYPE_EXPECTED,
- dd->ipath_tidinvalid);
-
- tidbase = (u64 __iomem *) ((char __iomem *)(dd->ipath_kregbase) +
- dd->ipath_rcvegrbase +
- port * dd->ipath_rcvegrcnt *
- sizeof(*tidbase));
-
- for (i = 0; i < dd->ipath_rcvegrcnt; i++)
- ipath_ht_put_tid(dd, &tidbase[i], RCVHQ_RCV_TYPE_EAGER,
- dd->ipath_tidinvalid);
-}
-
-/**
- * ipath_ht_tidtemplate - setup constants for TID updates
- * @dd: the infinipath device
- *
- * We setup stuff that we use a lot, to avoid calculating each time
- */
-static void ipath_ht_tidtemplate(struct ipath_devdata *dd)
-{
- dd->ipath_tidtemplate = dd->ipath_ibmaxlen >> 2;
- dd->ipath_tidtemplate <<= INFINIPATH_RT_BUFSIZE_SHIFT;
- dd->ipath_tidtemplate |= INFINIPATH_RT_VALID;
-
- /*
- * work around chip errata bug 7358, by marking invalid tids
- * as having max length
- */
- dd->ipath_tidinvalid = (-1LL & INFINIPATH_RT_BUFSIZE_MASK) <<
- INFINIPATH_RT_BUFSIZE_SHIFT;
-}
-
-static int ipath_ht_early_init(struct ipath_devdata *dd)
-{
- u32 __iomem *piobuf;
- u32 pioincr, val32;
- int i;
-
- /*
- * one cache line; long IB headers will spill over into received
- * buffer
- */
- dd->ipath_rcvhdrentsize = 16;
- dd->ipath_rcvhdrsize = IPATH_DFLT_RCVHDRSIZE;
-
- /*
- * For HT, we allocate a somewhat overly large eager buffer,
- * such that we can guarantee that we can receive the largest
- * packet that we can send out. To truly support a 4KB MTU,
- * we need to bump this to a large value. To date, other than
- * testing, we have never encountered an HCA that can really
- * send 4KB MTU packets, so we do not handle that (we'll get
- * errors interrupts if we ever see one).
- */
- dd->ipath_rcvegrbufsize = dd->ipath_piosize2k;
-
- /*
- * the min() check here is currently a nop, but it may not
- * always be, depending on just how we do ipath_rcvegrbufsize
- */
- dd->ipath_ibmaxlen = min(dd->ipath_piosize2k,
- dd->ipath_rcvegrbufsize);
- dd->ipath_init_ibmaxlen = dd->ipath_ibmaxlen;
- ipath_ht_tidtemplate(dd);
-
- /*
- * zero all the TID entries at startup. We do this for sanity,
- * in case of a previous driver crash of some kind, and also
- * because the chip powers up with these memories in an unknown
- * state. Use portcnt, not cfgports, since this is for the
- * full chip, not for current (possibly different) configuration
- * value.
- * Chip Errata bug 6447
- */
- for (val32 = 0; val32 < dd->ipath_portcnt; val32++)
- ipath_ht_clear_tids(dd, val32);
-
- /*
- * write the pbc of each buffer, to be sure it's initialized, then
- * cancel all the buffers, and also abort any packets that might
- * have been in flight for some reason (the latter is for driver
- * unload/reload, but isn't a bad idea at first init). PIO send
- * isn't enabled at this point, so there is no danger of sending
- * these out on the wire.
- * Chip Errata bug 6610
- */
- piobuf = (u32 __iomem *) (((char __iomem *)(dd->ipath_kregbase)) +
- dd->ipath_piobufbase);
- pioincr = dd->ipath_palign / sizeof(*piobuf);
- for (i = 0; i < dd->ipath_piobcnt2k; i++) {
- /*
- * reasonable word count, just to init pbc
- */
- writel(16, piobuf);
- piobuf += pioincr;
- }
-
- ipath_get_eeprom_info(dd);
- if (dd->ipath_boardrev == 5) {
- /*
- * Later production QHT7040 has same changes as QHT7140, so
- * can use GPIO interrupts. They have serial #'s starting
- * with 128, rather than 112.
- */
- if (dd->ipath_serial[0] == '1' &&
- dd->ipath_serial[1] == '2' &&
- dd->ipath_serial[2] == '8')
- dd->ipath_flags |= IPATH_GPIO_INTR;
- else {
- ipath_dev_err(dd, "Unsupported InfiniPath board "
- "(serial number %.16s)!\n",
- dd->ipath_serial);
- return 1;
- }
- }
-
- if (dd->ipath_minrev >= 4) {
- /* Rev4+ reports extra errors via internal GPIO pins */
- dd->ipath_flags |= IPATH_GPIO_ERRINTRS;
- dd->ipath_gpio_mask |= IPATH_GPIO_ERRINTR_MASK;
- ipath_write_kreg(dd, dd->ipath_kregs->kr_gpio_mask,
- dd->ipath_gpio_mask);
- }
-
- return 0;
-}
-
-
-/**
- * ipath_init_ht_get_base_info - set chip-specific flags for user code
- * @dd: the infinipath device
- * @kbase: ipath_base_info pointer
- *
- * We set the PCIE flag because the lower bandwidth on PCIe vs
- * HyperTransport can affect some user packet algorithms.
- */
-static int ipath_ht_get_base_info(struct ipath_portdata *pd, void *kbase)
-{
- struct ipath_base_info *kinfo = kbase;
-
- kinfo->spi_runtime_flags |= IPATH_RUNTIME_HT |
- IPATH_RUNTIME_PIO_REGSWAPPED;
-
- if (pd->port_dd->ipath_minrev < 4)
- kinfo->spi_runtime_flags |= IPATH_RUNTIME_RCVHDR_COPY;
-
- return 0;
-}
-
-static void ipath_ht_free_irq(struct ipath_devdata *dd)
-{
- free_irq(dd->ipath_irq, dd);
- ht_destroy_irq(dd->ipath_irq);
- dd->ipath_irq = 0;
- dd->ipath_intconfig = 0;
-}
-
-static struct ipath_message_header *
-ipath_ht_get_msgheader(struct ipath_devdata *dd, __le32 *rhf_addr)
-{
- return (struct ipath_message_header *)
- &rhf_addr[sizeof(u64) / sizeof(u32)];
-}
-
-static void ipath_ht_config_ports(struct ipath_devdata *dd, ushort cfgports)
-{
- dd->ipath_portcnt =
- ipath_read_kreg32(dd, dd->ipath_kregs->kr_portcnt);
- dd->ipath_p0_rcvegrcnt =
- ipath_read_kreg32(dd, dd->ipath_kregs->kr_rcvegrcnt);
-}
-
-static void ipath_ht_read_counters(struct ipath_devdata *dd,
- struct infinipath_counters *cntrs)
-{
- cntrs->LBIntCnt =
- ipath_snap_cntr(dd, IPATH_CREG_OFFSET(LBIntCnt));
- cntrs->LBFlowStallCnt =
- ipath_snap_cntr(dd, IPATH_CREG_OFFSET(LBFlowStallCnt));
- cntrs->TxSDmaDescCnt = 0;
- cntrs->TxUnsupVLErrCnt =
- ipath_snap_cntr(dd, IPATH_CREG_OFFSET(TxUnsupVLErrCnt));
- cntrs->TxDataPktCnt =
- ipath_snap_cntr(dd, IPATH_CREG_OFFSET(TxDataPktCnt));
- cntrs->TxFlowPktCnt =
- ipath_snap_cntr(dd, IPATH_CREG_OFFSET(TxFlowPktCnt));
- cntrs->TxDwordCnt =
- ipath_snap_cntr(dd, IPATH_CREG_OFFSET(TxDwordCnt));
- cntrs->TxLenErrCnt =
- ipath_snap_cntr(dd, IPATH_CREG_OFFSET(TxLenErrCnt));
- cntrs->TxMaxMinLenErrCnt =
- ipath_snap_cntr(dd, IPATH_CREG_OFFSET(TxMaxMinLenErrCnt));
- cntrs->TxUnderrunCnt =
- ipath_snap_cntr(dd, IPATH_CREG_OFFSET(TxUnderrunCnt));
- cntrs->TxFlowStallCnt =
- ipath_snap_cntr(dd, IPATH_CREG_OFFSET(TxFlowStallCnt));
- cntrs->TxDroppedPktCnt =
- ipath_snap_cntr(dd, IPATH_CREG_OFFSET(TxDroppedPktCnt));
- cntrs->RxDroppedPktCnt =
- ipath_snap_cntr(dd, IPATH_CREG_OFFSET(RxDroppedPktCnt));
- cntrs->RxDataPktCnt =
- ipath_snap_cntr(dd, IPATH_CREG_OFFSET(RxDataPktCnt));
- cntrs->RxFlowPktCnt =
- ipath_snap_cntr(dd, IPATH_CREG_OFFSET(RxFlowPktCnt));
- cntrs->RxDwordCnt =
- ipath_snap_cntr(dd, IPATH_CREG_OFFSET(RxDwordCnt));
- cntrs->RxLenErrCnt =
- ipath_snap_cntr(dd, IPATH_CREG_OFFSET(RxLenErrCnt));
- cntrs->RxMaxMinLenErrCnt =
- ipath_snap_cntr(dd, IPATH_CREG_OFFSET(RxMaxMinLenErrCnt));
- cntrs->RxICRCErrCnt =
- ipath_snap_cntr(dd, IPATH_CREG_OFFSET(RxICRCErrCnt));
- cntrs->RxVCRCErrCnt =
- ipath_snap_cntr(dd, IPATH_CREG_OFFSET(RxVCRCErrCnt));
- cntrs->RxFlowCtrlErrCnt =
- ipath_snap_cntr(dd, IPATH_CREG_OFFSET(RxFlowCtrlErrCnt));
- cntrs->RxBadFormatCnt =
- ipath_snap_cntr(dd, IPATH_CREG_OFFSET(RxBadFormatCnt));
- cntrs->RxLinkProblemCnt =
- ipath_snap_cntr(dd, IPATH_CREG_OFFSET(RxLinkProblemCnt));
- cntrs->RxEBPCnt =
- ipath_snap_cntr(dd, IPATH_CREG_OFFSET(RxEBPCnt));
- cntrs->RxLPCRCErrCnt =
- ipath_snap_cntr(dd, IPATH_CREG_OFFSET(RxLPCRCErrCnt));
- cntrs->RxBufOvflCnt =
- ipath_snap_cntr(dd, IPATH_CREG_OFFSET(RxBufOvflCnt));
- cntrs->RxTIDFullErrCnt =
- ipath_snap_cntr(dd, IPATH_CREG_OFFSET(RxTIDFullErrCnt));
- cntrs->RxTIDValidErrCnt =
- ipath_snap_cntr(dd, IPATH_CREG_OFFSET(RxTIDValidErrCnt));
- cntrs->RxPKeyMismatchCnt =
- ipath_snap_cntr(dd, IPATH_CREG_OFFSET(RxPKeyMismatchCnt));
- cntrs->RxP0HdrEgrOvflCnt =
- ipath_snap_cntr(dd, IPATH_CREG_OFFSET(RxP0HdrEgrOvflCnt));
- cntrs->RxP1HdrEgrOvflCnt =
- ipath_snap_cntr(dd, IPATH_CREG_OFFSET(RxP1HdrEgrOvflCnt));
- cntrs->RxP2HdrEgrOvflCnt =
- ipath_snap_cntr(dd, IPATH_CREG_OFFSET(RxP2HdrEgrOvflCnt));
- cntrs->RxP3HdrEgrOvflCnt =
- ipath_snap_cntr(dd, IPATH_CREG_OFFSET(RxP3HdrEgrOvflCnt));
- cntrs->RxP4HdrEgrOvflCnt =
- ipath_snap_cntr(dd, IPATH_CREG_OFFSET(RxP4HdrEgrOvflCnt));
- cntrs->RxP5HdrEgrOvflCnt =
- ipath_snap_cntr(dd, IPATH_CREG_OFFSET(RxP5HdrEgrOvflCnt));
- cntrs->RxP6HdrEgrOvflCnt =
- ipath_snap_cntr(dd, IPATH_CREG_OFFSET(RxP6HdrEgrOvflCnt));
- cntrs->RxP7HdrEgrOvflCnt =
- ipath_snap_cntr(dd, IPATH_CREG_OFFSET(RxP7HdrEgrOvflCnt));
- cntrs->RxP8HdrEgrOvflCnt =
- ipath_snap_cntr(dd, IPATH_CREG_OFFSET(RxP8HdrEgrOvflCnt));
- cntrs->RxP9HdrEgrOvflCnt = 0;
- cntrs->RxP10HdrEgrOvflCnt = 0;
- cntrs->RxP11HdrEgrOvflCnt = 0;
- cntrs->RxP12HdrEgrOvflCnt = 0;
- cntrs->RxP13HdrEgrOvflCnt = 0;
- cntrs->RxP14HdrEgrOvflCnt = 0;
- cntrs->RxP15HdrEgrOvflCnt = 0;
- cntrs->RxP16HdrEgrOvflCnt = 0;
- cntrs->IBStatusChangeCnt =
- ipath_snap_cntr(dd, IPATH_CREG_OFFSET(IBStatusChangeCnt));
- cntrs->IBLinkErrRecoveryCnt =
- ipath_snap_cntr(dd, IPATH_CREG_OFFSET(IBLinkErrRecoveryCnt));
- cntrs->IBLinkDownedCnt =
- ipath_snap_cntr(dd, IPATH_CREG_OFFSET(IBLinkDownedCnt));
- cntrs->IBSymbolErrCnt =
- ipath_snap_cntr(dd, IPATH_CREG_OFFSET(IBSymbolErrCnt));
- cntrs->RxVL15DroppedPktCnt = 0;
- cntrs->RxOtherLocalPhyErrCnt = 0;
- cntrs->PcieRetryBufDiagQwordCnt = 0;
- cntrs->ExcessBufferOvflCnt = dd->ipath_overrun_thresh_errs;
- cntrs->LocalLinkIntegrityErrCnt =
- (dd->ipath_flags & IPATH_GPIO_ERRINTRS) ?
- dd->ipath_lli_errs : dd->ipath_lli_errors;
- cntrs->RxVlErrCnt = 0;
- cntrs->RxDlidFltrCnt = 0;
-}
-
-
-/* no interrupt fallback for these chips */
-static int ipath_ht_nointr_fallback(struct ipath_devdata *dd)
-{
- return 0;
-}
-
-
-/*
- * reset the XGXS (between serdes and IBC). Slightly less intrusive
- * than resetting the IBC or external link state, and useful in some
- * cases to cause some retraining. To do this right, we reset IBC
- * as well.
- */
-static void ipath_ht_xgxs_reset(struct ipath_devdata *dd)
-{
- u64 val, prev_val;
-
- prev_val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_xgxsconfig);
- val = prev_val | INFINIPATH_XGXS_RESET;
- prev_val &= ~INFINIPATH_XGXS_RESET; /* be sure */
- ipath_write_kreg(dd, dd->ipath_kregs->kr_control,
- dd->ipath_control & ~INFINIPATH_C_LINKENABLE);
- ipath_write_kreg(dd, dd->ipath_kregs->kr_xgxsconfig, val);
- ipath_read_kreg32(dd, dd->ipath_kregs->kr_scratch);
- ipath_write_kreg(dd, dd->ipath_kregs->kr_xgxsconfig, prev_val);
- ipath_write_kreg(dd, dd->ipath_kregs->kr_control,
- dd->ipath_control);
-}
-
-
-static int ipath_ht_get_ib_cfg(struct ipath_devdata *dd, int which)
-{
- int ret;
-
- switch (which) {
- case IPATH_IB_CFG_LWID:
- ret = dd->ipath_link_width_active;
- break;
- case IPATH_IB_CFG_SPD:
- ret = dd->ipath_link_speed_active;
- break;
- case IPATH_IB_CFG_LWID_ENB:
- ret = dd->ipath_link_width_enabled;
- break;
- case IPATH_IB_CFG_SPD_ENB:
- ret = dd->ipath_link_speed_enabled;
- break;
- default:
- ret = -ENOTSUPP;
- break;
- }
- return ret;
-}
-
-
-/* we assume range checking is already done, if needed */
-static int ipath_ht_set_ib_cfg(struct ipath_devdata *dd, int which, u32 val)
-{
- int ret = 0;
-
- if (which == IPATH_IB_CFG_LWID_ENB)
- dd->ipath_link_width_enabled = val;
- else if (which == IPATH_IB_CFG_SPD_ENB)
- dd->ipath_link_speed_enabled = val;
- else
- ret = -ENOTSUPP;
- return ret;
-}
-
-
-static void ipath_ht_config_jint(struct ipath_devdata *dd, u16 a, u16 b)
-{
-}
-
-
-static int ipath_ht_ib_updown(struct ipath_devdata *dd, int ibup, u64 ibcs)
-{
- ipath_setup_ht_setextled(dd, ipath_ib_linkstate(dd, ibcs),
- ipath_ib_linktrstate(dd, ibcs));
- return 0;
-}
-
-
-/**
- * ipath_init_iba6110_funcs - set up the chip-specific function pointers
- * @dd: the infinipath device
- *
- * This is global, and is called directly at init to set up the
- * chip-specific function pointers for later use.
- */
-void ipath_init_iba6110_funcs(struct ipath_devdata *dd)
-{
- dd->ipath_f_intrsetup = ipath_ht_intconfig;
- dd->ipath_f_bus = ipath_setup_ht_config;
- dd->ipath_f_reset = ipath_setup_ht_reset;
- dd->ipath_f_get_boardname = ipath_ht_boardname;
- dd->ipath_f_init_hwerrors = ipath_ht_init_hwerrors;
- dd->ipath_f_early_init = ipath_ht_early_init;
- dd->ipath_f_handle_hwerrors = ipath_ht_handle_hwerrors;
- dd->ipath_f_quiet_serdes = ipath_ht_quiet_serdes;
- dd->ipath_f_bringup_serdes = ipath_ht_bringup_serdes;
- dd->ipath_f_clear_tids = ipath_ht_clear_tids;
- dd->ipath_f_put_tid = ipath_ht_put_tid;
- dd->ipath_f_cleanup = ipath_setup_ht_cleanup;
- dd->ipath_f_setextled = ipath_setup_ht_setextled;
- dd->ipath_f_get_base_info = ipath_ht_get_base_info;
- dd->ipath_f_free_irq = ipath_ht_free_irq;
- dd->ipath_f_tidtemplate = ipath_ht_tidtemplate;
- dd->ipath_f_intr_fallback = ipath_ht_nointr_fallback;
- dd->ipath_f_get_msgheader = ipath_ht_get_msgheader;
- dd->ipath_f_config_ports = ipath_ht_config_ports;
- dd->ipath_f_read_counters = ipath_ht_read_counters;
- dd->ipath_f_xgxs_reset = ipath_ht_xgxs_reset;
- dd->ipath_f_get_ib_cfg = ipath_ht_get_ib_cfg;
- dd->ipath_f_set_ib_cfg = ipath_ht_set_ib_cfg;
- dd->ipath_f_config_jint = ipath_ht_config_jint;
- dd->ipath_f_ib_updown = ipath_ht_ib_updown;
-
- /*
- * initialize chip-specific variables
- */
- ipath_init_ht_variables(dd);
-}
Code Review / kvmfornfv.git / blobdiff