Add the rt linux 4.1.3-rt3 as base
[kvmfornfv.git] / kernel / drivers / hwmon / pmbus / pmbus.h
diff --git a/kernel/drivers/hwmon/pmbus/pmbus.h b/kernel/drivers/hwmon/pmbus/pmbus.h
new file mode 100644 (file)
index 0000000..89a23ff
--- /dev/null
@@ -0,0 +1,417 @@
+/*
+ * pmbus.h - Common defines and structures for PMBus devices
+ *
+ * Copyright (c) 2010, 2011 Ericsson AB.
+ * Copyright (c) 2012 Guenter Roeck
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/regulator/driver.h>
+
+#ifndef PMBUS_H
+#define PMBUS_H
+
+/*
+ * Registers
+ */
+#define PMBUS_PAGE                     0x00
+#define PMBUS_OPERATION                        0x01
+#define PMBUS_ON_OFF_CONFIG            0x02
+#define PMBUS_CLEAR_FAULTS             0x03
+#define PMBUS_PHASE                    0x04
+
+#define PMBUS_CAPABILITY               0x19
+#define PMBUS_QUERY                    0x1A
+
+#define PMBUS_VOUT_MODE                        0x20
+#define PMBUS_VOUT_COMMAND             0x21
+#define PMBUS_VOUT_TRIM                        0x22
+#define PMBUS_VOUT_CAL_OFFSET          0x23
+#define PMBUS_VOUT_MAX                 0x24
+#define PMBUS_VOUT_MARGIN_HIGH         0x25
+#define PMBUS_VOUT_MARGIN_LOW          0x26
+#define PMBUS_VOUT_TRANSITION_RATE     0x27
+#define PMBUS_VOUT_DROOP               0x28
+#define PMBUS_VOUT_SCALE_LOOP          0x29
+#define PMBUS_VOUT_SCALE_MONITOR       0x2A
+
+#define PMBUS_COEFFICIENTS             0x30
+#define PMBUS_POUT_MAX                 0x31
+
+#define PMBUS_FAN_CONFIG_12            0x3A
+#define PMBUS_FAN_COMMAND_1            0x3B
+#define PMBUS_FAN_COMMAND_2            0x3C
+#define PMBUS_FAN_CONFIG_34            0x3D
+#define PMBUS_FAN_COMMAND_3            0x3E
+#define PMBUS_FAN_COMMAND_4            0x3F
+
+#define PMBUS_VOUT_OV_FAULT_LIMIT      0x40
+#define PMBUS_VOUT_OV_FAULT_RESPONSE   0x41
+#define PMBUS_VOUT_OV_WARN_LIMIT       0x42
+#define PMBUS_VOUT_UV_WARN_LIMIT       0x43
+#define PMBUS_VOUT_UV_FAULT_LIMIT      0x44
+#define PMBUS_VOUT_UV_FAULT_RESPONSE   0x45
+#define PMBUS_IOUT_OC_FAULT_LIMIT      0x46
+#define PMBUS_IOUT_OC_FAULT_RESPONSE   0x47
+#define PMBUS_IOUT_OC_LV_FAULT_LIMIT   0x48
+#define PMBUS_IOUT_OC_LV_FAULT_RESPONSE        0x49
+#define PMBUS_IOUT_OC_WARN_LIMIT       0x4A
+#define PMBUS_IOUT_UC_FAULT_LIMIT      0x4B
+#define PMBUS_IOUT_UC_FAULT_RESPONSE   0x4C
+
+#define PMBUS_OT_FAULT_LIMIT           0x4F
+#define PMBUS_OT_FAULT_RESPONSE                0x50
+#define PMBUS_OT_WARN_LIMIT            0x51
+#define PMBUS_UT_WARN_LIMIT            0x52
+#define PMBUS_UT_FAULT_LIMIT           0x53
+#define PMBUS_UT_FAULT_RESPONSE                0x54
+#define PMBUS_VIN_OV_FAULT_LIMIT       0x55
+#define PMBUS_VIN_OV_FAULT_RESPONSE    0x56
+#define PMBUS_VIN_OV_WARN_LIMIT                0x57
+#define PMBUS_VIN_UV_WARN_LIMIT                0x58
+#define PMBUS_VIN_UV_FAULT_LIMIT       0x59
+
+#define PMBUS_IIN_OC_FAULT_LIMIT       0x5B
+#define PMBUS_IIN_OC_WARN_LIMIT                0x5D
+
+#define PMBUS_POUT_OP_FAULT_LIMIT      0x68
+#define PMBUS_POUT_OP_WARN_LIMIT       0x6A
+#define PMBUS_PIN_OP_WARN_LIMIT                0x6B
+
+#define PMBUS_STATUS_BYTE              0x78
+#define PMBUS_STATUS_WORD              0x79
+#define PMBUS_STATUS_VOUT              0x7A
+#define PMBUS_STATUS_IOUT              0x7B
+#define PMBUS_STATUS_INPUT             0x7C
+#define PMBUS_STATUS_TEMPERATURE       0x7D
+#define PMBUS_STATUS_CML               0x7E
+#define PMBUS_STATUS_OTHER             0x7F
+#define PMBUS_STATUS_MFR_SPECIFIC      0x80
+#define PMBUS_STATUS_FAN_12            0x81
+#define PMBUS_STATUS_FAN_34            0x82
+
+#define PMBUS_READ_VIN                 0x88
+#define PMBUS_READ_IIN                 0x89
+#define PMBUS_READ_VCAP                        0x8A
+#define PMBUS_READ_VOUT                        0x8B
+#define PMBUS_READ_IOUT                        0x8C
+#define PMBUS_READ_TEMPERATURE_1       0x8D
+#define PMBUS_READ_TEMPERATURE_2       0x8E
+#define PMBUS_READ_TEMPERATURE_3       0x8F
+#define PMBUS_READ_FAN_SPEED_1         0x90
+#define PMBUS_READ_FAN_SPEED_2         0x91
+#define PMBUS_READ_FAN_SPEED_3         0x92
+#define PMBUS_READ_FAN_SPEED_4         0x93
+#define PMBUS_READ_DUTY_CYCLE          0x94
+#define PMBUS_READ_FREQUENCY           0x95
+#define PMBUS_READ_POUT                        0x96
+#define PMBUS_READ_PIN                 0x97
+
+#define PMBUS_REVISION                 0x98
+#define PMBUS_MFR_ID                   0x99
+#define PMBUS_MFR_MODEL                        0x9A
+#define PMBUS_MFR_REVISION             0x9B
+#define PMBUS_MFR_LOCATION             0x9C
+#define PMBUS_MFR_DATE                 0x9D
+#define PMBUS_MFR_SERIAL               0x9E
+
+/*
+ * Virtual registers.
+ * Useful to support attributes which are not supported by standard PMBus
+ * registers but exist as manufacturer specific registers on individual chips.
+ * Must be mapped to real registers in device specific code.
+ *
+ * Semantics:
+ * Virtual registers are all word size.
+ * READ registers are read-only; writes are either ignored or return an error.
+ * RESET registers are read/write. Reading reset registers returns zero
+ * (used for detection), writing any value causes the associated history to be
+ * reset.
+ * Virtual registers have to be handled in device specific driver code. Chip
+ * driver code returns non-negative register values if a virtual register is
+ * supported, or a negative error code if not. The chip driver may return
+ * -ENODATA or any other error code in this case, though an error code other
+ * than -ENODATA is handled more efficiently and thus preferred. Either case,
+ * the calling PMBus core code will abort if the chip driver returns an error
+ * code when reading or writing virtual registers.
+ */
+#define PMBUS_VIRT_BASE                        0x100
+#define PMBUS_VIRT_READ_TEMP_AVG       (PMBUS_VIRT_BASE + 0)
+#define PMBUS_VIRT_READ_TEMP_MIN       (PMBUS_VIRT_BASE + 1)
+#define PMBUS_VIRT_READ_TEMP_MAX       (PMBUS_VIRT_BASE + 2)
+#define PMBUS_VIRT_RESET_TEMP_HISTORY  (PMBUS_VIRT_BASE + 3)
+#define PMBUS_VIRT_READ_VIN_AVG                (PMBUS_VIRT_BASE + 4)
+#define PMBUS_VIRT_READ_VIN_MIN                (PMBUS_VIRT_BASE + 5)
+#define PMBUS_VIRT_READ_VIN_MAX                (PMBUS_VIRT_BASE + 6)
+#define PMBUS_VIRT_RESET_VIN_HISTORY   (PMBUS_VIRT_BASE + 7)
+#define PMBUS_VIRT_READ_IIN_AVG                (PMBUS_VIRT_BASE + 8)
+#define PMBUS_VIRT_READ_IIN_MIN                (PMBUS_VIRT_BASE + 9)
+#define PMBUS_VIRT_READ_IIN_MAX                (PMBUS_VIRT_BASE + 10)
+#define PMBUS_VIRT_RESET_IIN_HISTORY   (PMBUS_VIRT_BASE + 11)
+#define PMBUS_VIRT_READ_PIN_AVG                (PMBUS_VIRT_BASE + 12)
+#define PMBUS_VIRT_READ_PIN_MAX                (PMBUS_VIRT_BASE + 13)
+#define PMBUS_VIRT_RESET_PIN_HISTORY   (PMBUS_VIRT_BASE + 14)
+#define PMBUS_VIRT_READ_POUT_AVG       (PMBUS_VIRT_BASE + 15)
+#define PMBUS_VIRT_READ_POUT_MAX       (PMBUS_VIRT_BASE + 16)
+#define PMBUS_VIRT_RESET_POUT_HISTORY  (PMBUS_VIRT_BASE + 17)
+#define PMBUS_VIRT_READ_VOUT_AVG       (PMBUS_VIRT_BASE + 18)
+#define PMBUS_VIRT_READ_VOUT_MIN       (PMBUS_VIRT_BASE + 19)
+#define PMBUS_VIRT_READ_VOUT_MAX       (PMBUS_VIRT_BASE + 20)
+#define PMBUS_VIRT_RESET_VOUT_HISTORY  (PMBUS_VIRT_BASE + 21)
+#define PMBUS_VIRT_READ_IOUT_AVG       (PMBUS_VIRT_BASE + 22)
+#define PMBUS_VIRT_READ_IOUT_MIN       (PMBUS_VIRT_BASE + 23)
+#define PMBUS_VIRT_READ_IOUT_MAX       (PMBUS_VIRT_BASE + 24)
+#define PMBUS_VIRT_RESET_IOUT_HISTORY  (PMBUS_VIRT_BASE + 25)
+#define PMBUS_VIRT_READ_TEMP2_AVG      (PMBUS_VIRT_BASE + 26)
+#define PMBUS_VIRT_READ_TEMP2_MIN      (PMBUS_VIRT_BASE + 27)
+#define PMBUS_VIRT_READ_TEMP2_MAX      (PMBUS_VIRT_BASE + 28)
+#define PMBUS_VIRT_RESET_TEMP2_HISTORY (PMBUS_VIRT_BASE + 29)
+
+#define PMBUS_VIRT_READ_VMON           (PMBUS_VIRT_BASE + 30)
+#define PMBUS_VIRT_VMON_UV_WARN_LIMIT  (PMBUS_VIRT_BASE + 31)
+#define PMBUS_VIRT_VMON_OV_WARN_LIMIT  (PMBUS_VIRT_BASE + 32)
+#define PMBUS_VIRT_VMON_UV_FAULT_LIMIT (PMBUS_VIRT_BASE + 33)
+#define PMBUS_VIRT_VMON_OV_FAULT_LIMIT (PMBUS_VIRT_BASE + 34)
+#define PMBUS_VIRT_STATUS_VMON         (PMBUS_VIRT_BASE + 35)
+
+/*
+ * OPERATION
+ */
+#define PB_OPERATION_CONTROL_ON                (1<<7)
+
+/*
+ * CAPABILITY
+ */
+#define PB_CAPABILITY_SMBALERT         (1<<4)
+#define PB_CAPABILITY_ERROR_CHECK      (1<<7)
+
+/*
+ * VOUT_MODE
+ */
+#define PB_VOUT_MODE_MODE_MASK         0xe0
+#define PB_VOUT_MODE_PARAM_MASK                0x1f
+
+#define PB_VOUT_MODE_LINEAR            0x00
+#define PB_VOUT_MODE_VID               0x20
+#define PB_VOUT_MODE_DIRECT            0x40
+
+/*
+ * Fan configuration
+ */
+#define PB_FAN_2_PULSE_MASK            ((1 << 0) | (1 << 1))
+#define PB_FAN_2_RPM                   (1 << 2)
+#define PB_FAN_2_INSTALLED             (1 << 3)
+#define PB_FAN_1_PULSE_MASK            ((1 << 4) | (1 << 5))
+#define PB_FAN_1_RPM                   (1 << 6)
+#define PB_FAN_1_INSTALLED             (1 << 7)
+
+/*
+ * STATUS_BYTE, STATUS_WORD (lower)
+ */
+#define PB_STATUS_NONE_ABOVE           (1<<0)
+#define PB_STATUS_CML                  (1<<1)
+#define PB_STATUS_TEMPERATURE          (1<<2)
+#define PB_STATUS_VIN_UV               (1<<3)
+#define PB_STATUS_IOUT_OC              (1<<4)
+#define PB_STATUS_VOUT_OV              (1<<5)
+#define PB_STATUS_OFF                  (1<<6)
+#define PB_STATUS_BUSY                 (1<<7)
+
+/*
+ * STATUS_WORD (upper)
+ */
+#define PB_STATUS_UNKNOWN              (1<<8)
+#define PB_STATUS_OTHER                        (1<<9)
+#define PB_STATUS_FANS                 (1<<10)
+#define PB_STATUS_POWER_GOOD_N         (1<<11)
+#define PB_STATUS_WORD_MFR             (1<<12)
+#define PB_STATUS_INPUT                        (1<<13)
+#define PB_STATUS_IOUT_POUT            (1<<14)
+#define PB_STATUS_VOUT                 (1<<15)
+
+/*
+ * STATUS_IOUT
+ */
+#define PB_POUT_OP_WARNING             (1<<0)
+#define PB_POUT_OP_FAULT               (1<<1)
+#define PB_POWER_LIMITING              (1<<2)
+#define PB_CURRENT_SHARE_FAULT         (1<<3)
+#define PB_IOUT_UC_FAULT               (1<<4)
+#define PB_IOUT_OC_WARNING             (1<<5)
+#define PB_IOUT_OC_LV_FAULT            (1<<6)
+#define PB_IOUT_OC_FAULT               (1<<7)
+
+/*
+ * STATUS_VOUT, STATUS_INPUT
+ */
+#define PB_VOLTAGE_UV_FAULT            (1<<4)
+#define PB_VOLTAGE_UV_WARNING          (1<<5)
+#define PB_VOLTAGE_OV_WARNING          (1<<6)
+#define PB_VOLTAGE_OV_FAULT            (1<<7)
+
+/*
+ * STATUS_INPUT
+ */
+#define PB_PIN_OP_WARNING              (1<<0)
+#define PB_IIN_OC_WARNING              (1<<1)
+#define PB_IIN_OC_FAULT                        (1<<2)
+
+/*
+ * STATUS_TEMPERATURE
+ */
+#define PB_TEMP_UT_FAULT               (1<<4)
+#define PB_TEMP_UT_WARNING             (1<<5)
+#define PB_TEMP_OT_WARNING             (1<<6)
+#define PB_TEMP_OT_FAULT               (1<<7)
+
+/*
+ * STATUS_FAN
+ */
+#define PB_FAN_AIRFLOW_WARNING         (1<<0)
+#define PB_FAN_AIRFLOW_FAULT           (1<<1)
+#define PB_FAN_FAN2_SPEED_OVERRIDE     (1<<2)
+#define PB_FAN_FAN1_SPEED_OVERRIDE     (1<<3)
+#define PB_FAN_FAN2_WARNING            (1<<4)
+#define PB_FAN_FAN1_WARNING            (1<<5)
+#define PB_FAN_FAN2_FAULT              (1<<6)
+#define PB_FAN_FAN1_FAULT              (1<<7)
+
+/*
+ * CML_FAULT_STATUS
+ */
+#define PB_CML_FAULT_OTHER_MEM_LOGIC   (1<<0)
+#define PB_CML_FAULT_OTHER_COMM                (1<<1)
+#define PB_CML_FAULT_PROCESSOR         (1<<3)
+#define PB_CML_FAULT_MEMORY            (1<<4)
+#define PB_CML_FAULT_PACKET_ERROR      (1<<5)
+#define PB_CML_FAULT_INVALID_DATA      (1<<6)
+#define PB_CML_FAULT_INVALID_COMMAND   (1<<7)
+
+enum pmbus_sensor_classes {
+       PSC_VOLTAGE_IN = 0,
+       PSC_VOLTAGE_OUT,
+       PSC_CURRENT_IN,
+       PSC_CURRENT_OUT,
+       PSC_POWER,
+       PSC_TEMPERATURE,
+       PSC_FAN,
+       PSC_NUM_CLASSES         /* Number of power sensor classes */
+};
+
+#define PMBUS_PAGES    32      /* Per PMBus specification */
+
+/* Functionality bit mask */
+#define PMBUS_HAVE_VIN         (1 << 0)
+#define PMBUS_HAVE_VCAP                (1 << 1)
+#define PMBUS_HAVE_VOUT                (1 << 2)
+#define PMBUS_HAVE_IIN         (1 << 3)
+#define PMBUS_HAVE_IOUT                (1 << 4)
+#define PMBUS_HAVE_PIN         (1 << 5)
+#define PMBUS_HAVE_POUT                (1 << 6)
+#define PMBUS_HAVE_FAN12       (1 << 7)
+#define PMBUS_HAVE_FAN34       (1 << 8)
+#define PMBUS_HAVE_TEMP                (1 << 9)
+#define PMBUS_HAVE_TEMP2       (1 << 10)
+#define PMBUS_HAVE_TEMP3       (1 << 11)
+#define PMBUS_HAVE_STATUS_VOUT (1 << 12)
+#define PMBUS_HAVE_STATUS_IOUT (1 << 13)
+#define PMBUS_HAVE_STATUS_INPUT        (1 << 14)
+#define PMBUS_HAVE_STATUS_TEMP (1 << 15)
+#define PMBUS_HAVE_STATUS_FAN12        (1 << 16)
+#define PMBUS_HAVE_STATUS_FAN34        (1 << 17)
+#define PMBUS_HAVE_VMON                (1 << 18)
+#define PMBUS_HAVE_STATUS_VMON (1 << 19)
+
+enum pmbus_data_format { linear = 0, direct, vid };
+
+struct pmbus_driver_info {
+       int pages;              /* Total number of pages */
+       enum pmbus_data_format format[PSC_NUM_CLASSES];
+       /*
+        * Support one set of coefficients for each sensor type
+        * Used for chips providing data in direct mode.
+        */
+       int m[PSC_NUM_CLASSES]; /* mantissa for direct data format */
+       int b[PSC_NUM_CLASSES]; /* offset */
+       int R[PSC_NUM_CLASSES]; /* exponent */
+
+       u32 func[PMBUS_PAGES];  /* Functionality, per page */
+       /*
+        * The following functions map manufacturing specific register values
+        * to PMBus standard register values. Specify only if mapping is
+        * necessary.
+        * Functions return the register value (read) or zero (write) if
+        * successful. A return value of -ENODATA indicates that there is no
+        * manufacturer specific register, but that a standard PMBus register
+        * may exist. Any other negative return value indicates that the
+        * register does not exist, and that no attempt should be made to read
+        * the standard register.
+        */
+       int (*read_byte_data)(struct i2c_client *client, int page, int reg);
+       int (*read_word_data)(struct i2c_client *client, int page, int reg);
+       int (*write_word_data)(struct i2c_client *client, int page, int reg,
+                              u16 word);
+       int (*write_byte)(struct i2c_client *client, int page, u8 value);
+       /*
+        * The identify function determines supported PMBus functionality.
+        * This function is only necessary if a chip driver supports multiple
+        * chips, and the chip functionality is not pre-determined.
+        */
+       int (*identify)(struct i2c_client *client,
+                       struct pmbus_driver_info *info);
+
+       /* Regulator functionality, if supported by this chip driver. */
+       int num_regulators;
+       const struct regulator_desc *reg_desc;
+};
+
+/* Regulator ops */
+
+extern struct regulator_ops pmbus_regulator_ops;
+
+/* Macro for filling in array of struct regulator_desc */
+#define PMBUS_REGULATOR(_name, _id)                            \
+       [_id] = {                                               \
+               .name = (_name # _id),                          \
+               .id = (_id),                                    \
+               .of_match = of_match_ptr(_name # _id),          \
+               .regulators_node = of_match_ptr("regulators"),  \
+               .ops = &pmbus_regulator_ops,                    \
+               .owner = THIS_MODULE,                           \
+       }
+
+/* Function declarations */
+
+void pmbus_clear_cache(struct i2c_client *client);
+int pmbus_set_page(struct i2c_client *client, u8 page);
+int pmbus_read_word_data(struct i2c_client *client, u8 page, u8 reg);
+int pmbus_write_word_data(struct i2c_client *client, u8 page, u8 reg, u16 word);
+int pmbus_read_byte_data(struct i2c_client *client, int page, u8 reg);
+int pmbus_write_byte(struct i2c_client *client, int page, u8 value);
+int pmbus_write_byte_data(struct i2c_client *client, int page, u8 reg,
+                         u8 value);
+int pmbus_update_byte_data(struct i2c_client *client, int page, u8 reg,
+                          u8 mask, u8 value);
+void pmbus_clear_faults(struct i2c_client *client);
+bool pmbus_check_byte_register(struct i2c_client *client, int page, int reg);
+bool pmbus_check_word_register(struct i2c_client *client, int page, int reg);
+int pmbus_do_probe(struct i2c_client *client, const struct i2c_device_id *id,
+                  struct pmbus_driver_info *info);
+int pmbus_do_remove(struct i2c_client *client);
+const struct pmbus_driver_info *pmbus_get_driver_info(struct i2c_client
+                                                     *client);
+
+#endif /* PMBUS_H */