--- /dev/null
+/*
+ * Freescale Lite5200 board support
+ *
+ * Written by: Grant Likely <grant.likely@secretlab.ca>
+ *
+ * Copyright (C) Secret Lab Technologies Ltd. 2006. All rights reserved.
+ * Copyright 2006 Freescale Semiconductor, Inc. All rights reserved.
+ *
+ * Description:
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#undef DEBUG
+
+#include <linux/init.h>
+#include <linux/pci.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/root_dev.h>
+#include <linux/initrd.h>
+#include <asm/time.h>
+#include <asm/io.h>
+#include <asm/machdep.h>
+#include <asm/prom.h>
+#include <asm/mpc52xx.h>
+
+/* ************************************************************************
+ *
+ * Setup the architecture
+ *
+ */
+
+/* mpc5200 device tree match tables */
+static const struct of_device_id mpc5200_cdm_ids[] __initconst = {
+ { .compatible = "fsl,mpc5200-cdm", },
+ { .compatible = "mpc5200-cdm", },
+ {}
+};
+
+static const struct of_device_id mpc5200_gpio_ids[] __initconst = {
+ { .compatible = "fsl,mpc5200-gpio", },
+ { .compatible = "mpc5200-gpio", },
+ {}
+};
+
+/*
+ * Fix clock configuration.
+ *
+ * Firmware is supposed to be responsible for this. If you are creating a
+ * new board port, do *NOT* duplicate this code. Fix your boot firmware
+ * to set it correctly in the first place
+ */
+static void __init
+lite5200_fix_clock_config(void)
+{
+ struct device_node *np;
+ struct mpc52xx_cdm __iomem *cdm;
+ /* Map zones */
+ np = of_find_matching_node(NULL, mpc5200_cdm_ids);
+ cdm = of_iomap(np, 0);
+ of_node_put(np);
+ if (!cdm) {
+ printk(KERN_ERR "%s() failed; expect abnormal behaviour\n",
+ __func__);
+ return;
+ }
+
+ /* Use internal 48 Mhz */
+ out_8(&cdm->ext_48mhz_en, 0x00);
+ out_8(&cdm->fd_enable, 0x01);
+ if (in_be32(&cdm->rstcfg) & 0x40) /* Assumes 33Mhz clock */
+ out_be16(&cdm->fd_counters, 0x0001);
+ else
+ out_be16(&cdm->fd_counters, 0x5555);
+
+ /* Unmap the regs */
+ iounmap(cdm);
+}
+
+/*
+ * Fix setting of port_config register.
+ *
+ * Firmware is supposed to be responsible for this. If you are creating a
+ * new board port, do *NOT* duplicate this code. Fix your boot firmware
+ * to set it correctly in the first place
+ */
+static void __init
+lite5200_fix_port_config(void)
+{
+ struct device_node *np;
+ struct mpc52xx_gpio __iomem *gpio;
+ u32 port_config;
+
+ np = of_find_matching_node(NULL, mpc5200_gpio_ids);
+ gpio = of_iomap(np, 0);
+ of_node_put(np);
+ if (!gpio) {
+ printk(KERN_ERR "%s() failed. expect abnormal behavior\n",
+ __func__);
+ return;
+ }
+
+ /* Set port config */
+ port_config = in_be32(&gpio->port_config);
+
+ port_config &= ~0x00800000; /* 48Mhz internal, pin is GPIO */
+
+ port_config &= ~0x00007000; /* USB port : Differential mode */
+ port_config |= 0x00001000; /* USB 1 only */
+
+ port_config &= ~0x03000000; /* ATA CS is on csb_4/5 */
+ port_config |= 0x01000000;
+
+ pr_debug("port_config: old:%x new:%x\n",
+ in_be32(&gpio->port_config), port_config);
+ out_be32(&gpio->port_config, port_config);
+
+ /* Unmap zone */
+ iounmap(gpio);
+}
+
+#ifdef CONFIG_PM
+static void lite5200_suspend_prepare(void __iomem *mbar)
+{
+ u8 pin = 1; /* GPIO_WKUP_1 (GPIO_PSC2_4) */
+ u8 level = 0; /* wakeup on low level */
+ mpc52xx_set_wakeup_gpio(pin, level);
+
+ /*
+ * power down usb port
+ * this needs to be called before of-ohci suspend code
+ */
+
+ /* set ports to "power switched" and "powered at the same time"
+ * USB Rh descriptor A: NPS = 0, PSM = 0 */
+ out_be32(mbar + 0x1048, in_be32(mbar + 0x1048) & ~0x300);
+ /* USB Rh status: LPS = 1 - turn off power */
+ out_be32(mbar + 0x1050, 0x00000001);
+}
+
+static void lite5200_resume_finish(void __iomem *mbar)
+{
+ /* USB Rh status: LPSC = 1 - turn on power */
+ out_be32(mbar + 0x1050, 0x00010000);
+}
+#endif
+
+static void __init lite5200_setup_arch(void)
+{
+ if (ppc_md.progress)
+ ppc_md.progress("lite5200_setup_arch()", 0);
+
+ /* Map important registers from the internal memory map */
+ mpc52xx_map_common_devices();
+
+ /* Some mpc5200 & mpc5200b related configuration */
+ mpc5200_setup_xlb_arbiter();
+
+ /* Fix things that firmware should have done. */
+ lite5200_fix_clock_config();
+ lite5200_fix_port_config();
+
+#ifdef CONFIG_PM
+ mpc52xx_suspend.board_suspend_prepare = lite5200_suspend_prepare;
+ mpc52xx_suspend.board_resume_finish = lite5200_resume_finish;
+ lite5200_pm_init();
+#endif
+
+ mpc52xx_setup_pci();
+}
+
+static const char * const board[] __initconst = {
+ "fsl,lite5200",
+ "fsl,lite5200b",
+ NULL,
+};
+
+/*
+ * Called very early, MMU is off, device-tree isn't unflattened
+ */
+static int __init lite5200_probe(void)
+{
+ return of_flat_dt_match(of_get_flat_dt_root(), board);
+}
+
+define_machine(lite5200) {
+ .name = "lite5200",
+ .probe = lite5200_probe,
+ .setup_arch = lite5200_setup_arch,
+ .init = mpc52xx_declare_of_platform_devices,
+ .init_IRQ = mpc52xx_init_irq,
+ .get_irq = mpc52xx_get_irq,
+ .restart = mpc52xx_restart,
+ .calibrate_decr = generic_calibrate_decr,
+};
Code Review / kvmfornfv.git / blobdiff