--- /dev/null
+/*
+ * PHYTEC phyCORE-LPC3250 board
+ *
+ * Copyright 2012 Roland Stigge <stigge@antcom.de>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+/include/ "lpc32xx.dtsi"
+
+/ {
+ model = "PHYTEC phyCORE-LPC3250 board based on NXP LPC3250";
+ compatible = "phytec,phy3250", "nxp,lpc3250";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ memory {
+ device_type = "memory";
+ reg = <0 0x4000000>;
+ };
+
+ ahb {
+ mac: ethernet@31060000 {
+ phy-mode = "rmii";
+ use-iram;
+ };
+
+ /* Here, choose exactly one from: ohci, usbd */
+ ohci@31020000 {
+ transceiver = <&isp1301>;
+ status = "okay";
+ };
+
+/*
+ usbd@31020000 {
+ transceiver = <&isp1301>;
+ status = "okay";
+ };
+*/
+
+ clcd@31040000 {
+ status = "okay";
+ };
+
+ /* 64MB Flash via SLC NAND controller */
+ slc: flash@20020000 {
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ nxp,wdr-clks = <14>;
+ nxp,wwidth = <40000000>;
+ nxp,whold = <100000000>;
+ nxp,wsetup = <100000000>;
+ nxp,rdr-clks = <14>;
+ nxp,rwidth = <40000000>;
+ nxp,rhold = <66666666>;
+ nxp,rsetup = <100000000>;
+ nand-on-flash-bbt;
+ gpios = <&gpio 5 19 1>; /* GPO_P3 19, active low */
+
+ mtd0@00000000 {
+ label = "phy3250-boot";
+ reg = <0x00000000 0x00064000>;
+ read-only;
+ };
+
+ mtd1@00064000 {
+ label = "phy3250-uboot";
+ reg = <0x00064000 0x00190000>;
+ read-only;
+ };
+
+ mtd2@001f4000 {
+ label = "phy3250-ubt-prms";
+ reg = <0x001f4000 0x00010000>;
+ };
+
+ mtd3@00204000 {
+ label = "phy3250-kernel";
+ reg = <0x00204000 0x00400000>;
+ };
+
+ mtd4@00604000 {
+ label = "phy3250-rootfs";
+ reg = <0x00604000 0x039fc000>;
+ };
+ };
+
+ apb {
+ uart5: serial@40090000 {
+ status = "okay";
+ };
+
+ uart3: serial@40080000 {
+ status = "okay";
+ };
+
+ i2c1: i2c@400A0000 {
+ clock-frequency = <100000>;
+
+ pcf8563: rtc@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+
+ uda1380: uda1380@18 {
+ compatible = "nxp,uda1380";
+ reg = <0x18>;
+ power-gpio = <&gpio 0x59 0>;
+ reset-gpio = <&gpio 0x51 0>;
+ dac-clk = "wspll";
+ };
+ };
+
+ i2c2: i2c@400A8000 {
+ clock-frequency = <100000>;
+ };
+
+ i2cusb: i2c@31020300 {
+ clock-frequency = <100000>;
+
+ isp1301: usb-transceiver@2c {
+ compatible = "nxp,isp1301";
+ reg = <0x2c>;
+ };
+ };
+
+ ssp0: ssp@20084000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ num-cs = <1>;
+ cs-gpios = <&gpio 3 5 0>;
+
+ eeprom: at25@0 {
+ pl022,interface = <0>;
+ pl022,com-mode = <0>;
+ pl022,rx-level-trig = <1>;
+ pl022,tx-level-trig = <1>;
+ pl022,ctrl-len = <11>;
+ pl022,wait-state = <0>;
+ pl022,duplex = <0>;
+
+ at25,byte-len = <0x8000>;
+ at25,addr-mode = <2>;
+ at25,page-size = <64>;
+
+ compatible = "atmel,at25";
+ reg = <0>;
+ spi-max-frequency = <5000000>;
+ };
+ };
+
+ sd@20098000 {
+ wp-gpios = <&gpio 3 0 0>;
+ cd-gpios = <&gpio 3 1 0>;
+ cd-inverted;
+ bus-width = <4>;
+ status = "okay";
+ };
+ };
+
+ fab {
+ uart2: serial@40018000 {
+ status = "okay";
+ };
+
+ tsc@40048000 {
+ status = "okay";
+ };
+
+ key@40050000 {
+ status = "okay";
+ keypad,num-rows = <1>;
+ keypad,num-columns = <1>;
+ nxp,debounce-delay-ms = <3>;
+ nxp,scan-delay-ms = <34>;
+ linux,keymap = <0x00000002>;
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led0 { /* red */
+ gpios = <&gpio 5 1 0>; /* GPO_P3 1, GPIO 80, active high */
+ default-state = "off";
+ };
+
+ led1 { /* green */
+ gpios = <&gpio 5 14 0>; /* GPO_P3 14, GPIO 93, active high */
+ linux,default-trigger = "heartbeat";
+ };
+ };
+};
Code Review / kvmfornfv.git / blobdiff