These changes are the raw update to linux-4.4.6-rt14. Kernel sources

[kvmfornfv.git] / kernel / arch / arm / boot / dts / kizbox.dts

diff --git a/kernel/arch/arm/boot/dts/kizbox.dts b/kernel/arch/arm/boot/dts/kizbox.dts
deleted file mode 100644 (file)
index e83e4f9..0000000
--- a/kernel/arch/arm/boot/dts/kizbox.dts
+++ /dev/null
@@ -1,150 +0,0 @@
-/*
- * kizbox.dts - Device Tree file for Overkiz Kizbox board
- *
- * Copyright (C) 2012 Boris BREZILLON <linux-arm@overkiz.com>
- *
- * Licensed under GPLv2.
- */
-/dts-v1/;
-#include "at91sam9g20.dtsi"
-
-/ {
-
-       model = "Overkiz kizbox";
-       compatible = "overkiz,kizbox", "atmel,at91sam9g20", "atmel,at91sam9";
-
-       chosen {
-               bootargs = "panic=5 ubi.mtd=1 rootfstype=ubifs root=ubi0:root";
-       };
-
-       memory {
-               reg = <0x20000000 0x2000000>;
-       };
-
-       clocks {
-               #address-cells = <1>;
-               #size-cells = <1>;
-               ranges;
-
-               main_clock: clock@0 {
-                       compatible = "atmel,osc", "fixed-clock";
-                       clock-frequency = <18432000>;
-               };
-
-               main_xtal {
-                       clock-frequency = <18432000>;
-               };
-       };
-
-       ahb {
-               apb {
-                       dbgu: serial@fffff200 {
-                               status = "okay";
-                       };
-
-                       usart0: serial@fffb0000 {
-                               status = "okay";
-                       };
-
-                       usart1: serial@fffb4000 {
-                               status = "okay";
-                       };
-
-                       macb0: ethernet@fffc4000 {
-                               phy-mode = "mii";
-                               pinctrl-0 = <&pinctrl_macb_rmii
-                                            &pinctrl_macb_rmii_mii_alt>;
-                               status = "okay";
-                       };
-
-                       watchdog@fffffd40 {
-                               timeout-sec = <15>;
-                               atmel,max-heartbeat-sec = <16>;
-                               atmel,min-heartbeat-sec = <0>;
-                               status = "okay";
-                       };
-               };
-
-               nand0: nand@40000000 {
-                       nand-bus-width = <8>;
-                       nand-ecc-mode = "soft";
-                       status = "okay";
-
-                       bootloaderkernel@0 {
-                               label = "bootloader-kernel";
-                               reg = <0x0 0xc0000>;
-                       };
-
-                       ubi@c0000 {
-                               label = "ubi";
-                               reg = <0xc0000 0x7f40000>;
-                       };
-
-               };
-
-               usb0: ohci@00500000 {
-                       num-ports = <1>;
-                       status = "okay";
-               };
-       };
-
-       i2c@0 {
-               status = "okay";
-
-               pcf8563@51 {
-                       /* nxp pcf8563 rtc */
-                       compatible = "nxp,pcf8563";
-                       reg = <0x51>;
-               };
-
-       };
-
-       leds {
-               compatible = "gpio-leds";
-
-               led1g {
-                       label = "led1:green";
-                       gpios = <&pioB 0 GPIO_ACTIVE_LOW>;
-                       linux,default-trigger = "none";
-               };
-
-               led1r {
-                       label = "led1:red";
-                       gpios = <&pioB 1 GPIO_ACTIVE_LOW>;
-                       linux,default-trigger = "none";
-               };
-
-               led2g {
-                       label = "led2:green";
-                       gpios = <&pioB 2 GPIO_ACTIVE_LOW>;
-                       linux,default-trigger = "none";
-                       default-state = "on";
-               };
-
-               led2r {
-                       label = "led2:red";
-                       gpios = <&pioB 3 GPIO_ACTIVE_LOW>;
-                       linux,default-trigger = "none";
-               };
-       };
-
-       gpio_keys {
-               compatible = "gpio-keys";
-               #address-cells = <1>;
-               #size-cells = <0>;
-
-               reset {
-                       label = "reset";
-                       gpios = <&pioB 30 GPIO_ACTIVE_LOW>;
-                       linux,code = <0x100>;
-                       gpio-key,wakeup;
-               };
-
-               mode {
-                       label = "mode";
-                       gpios = <&pioB 31 GPIO_ACTIVE_LOW>;
-                       linux,code = <0x101>;
-                       gpio-key,wakeup;
-               };
-       };
-};