--- /dev/null
+/*
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+#include "imx28.dtsi"
+
+/ {
+ model = "Freescale i.MX28 Evaluation Kit";
+ compatible = "fsl,imx28-evk", "fsl,imx28";
+
+ memory {
+ reg = <0x40000000 0x08000000>;
+ };
+
+ apb@80000000 {
+ apbh@80000000 {
+ gpmi-nand@8000c000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg
+ &gpmi_pins_evk>;
+ status = "okay";
+ };
+
+ ssp0: ssp@80010000 {
+ compatible = "fsl,imx28-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_8bit_pins_a
+ &mmc0_cd_cfg &mmc0_sck_cfg>;
+ bus-width = <8>;
+ wp-gpios = <&gpio2 12 0>;
+ vmmc-supply = <®_vddio_sd0>;
+ status = "okay";
+ };
+
+ ssp1: ssp@80012000 {
+ compatible = "fsl,imx28-mmc";
+ bus-width = <8>;
+ wp-gpios = <&gpio0 28 0>;
+ };
+
+ ssp2: ssp@80014000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx28-spi";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi2_pins_a>;
+ status = "okay";
+
+ flash: m25p80@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "sst,sst25vf016b";
+ spi-max-frequency = <40000000>;
+ reg = <0>;
+ };
+ };
+
+ pinctrl@80018000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hog_pins_a>;
+
+ hog_pins_a: hog@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_SSP1_CMD__GPIO_2_13
+ MX28_PAD_SSP1_DATA3__GPIO_2_15
+ MX28_PAD_ENET0_RX_CLK__GPIO_4_13
+ MX28_PAD_SSP1_SCK__GPIO_2_12
+ MX28_PAD_PWM3__GPIO_3_28
+ MX28_PAD_LCD_RESET__GPIO_3_30
+ MX28_PAD_AUART2_RX__GPIO_3_8
+ MX28_PAD_AUART2_TX__GPIO_3_9
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ led_pin_gpio3_5: led_gpio3_5@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_AUART1_TX__GPIO_3_5
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ gpmi_pins_evk: gpmi-nand-evk@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_GPMI_CE1N__GPMI_CE1N
+ MX28_PAD_GPMI_RDY1__GPMI_READY1
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ lcdif_pins_evk: lcdif-evk@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_RD_E__LCD_VSYNC
+ MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+ MX28_PAD_LCD_RS__LCD_DOTCLK
+ MX28_PAD_LCD_CS__LCD_ENABLE
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+ };
+
+ lcdif@80030000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcdif_24bit_pins_a
+ &lcdif_pins_evk>;
+ lcd-supply = <®_lcd_3v3>;
+ display = <&display0>;
+ status = "okay";
+
+ display0: display0 {
+ bits-per-pixel = <32>;
+ bus-width = <24>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing0 {
+ clock-frequency = <33500000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <89>;
+ hfront-porch = <164>;
+ vback-porch = <23>;
+ vfront-porch = <10>;
+ hsync-len = <10>;
+ vsync-len = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+ };
+ };
+ };
+
+ can0: can@80032000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&can0_pins_a>;
+ xceiver-supply = <®_can_3v3>;
+ status = "okay";
+ };
+
+ can1: can@80034000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&can1_pins_a>;
+ xceiver-supply = <®_can_3v3>;
+ status = "okay";
+ };
+ };
+
+ apbx@80040000 {
+ saif0: saif@80042000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&saif0_pins_a>;
+ status = "okay";
+ };
+
+ saif1: saif@80046000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&saif1_pins_a>;
+ fsl,saif-master = <&saif0>;
+ status = "okay";
+ };
+
+ lradc@80050000 {
+ status = "okay";
+ fsl,lradc-touchscreen-wires = <4>;
+ fsl,ave-ctrl = <4>;
+ fsl,ave-delay = <2>;
+ fsl,settling = <10>;
+ };
+
+ i2c0: i2c@80058000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ sgtl5000: codec@0a {
+ compatible = "fsl,sgtl5000";
+ reg = <0x0a>;
+ VDDA-supply = <®_3p3v>;
+ VDDIO-supply = <®_3p3v>;
+ clocks = <&saif0>;
+ };
+
+ at24@51 {
+ compatible = "at24,24c32";
+ pagesize = <32>;
+ reg = <0x51>;
+ };
+ };
+
+ pwm: pwm@80064000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm2_pins_a>;
+ status = "okay";
+ };
+
+ duart: serial@80074000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&duart_pins_a>;
+ status = "okay";
+ };
+
+ auart0: serial@8006a000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&auart0_pins_a>;
+ fsl,uart-has-rtscts;
+ status = "okay";
+ };
+
+ auart3: serial@80070000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&auart3_pins_a>;
+ status = "okay";
+ };
+
+ usbphy0: usbphy@8007c000 {
+ status = "okay";
+ };
+
+ usbphy1: usbphy@8007e000 {
+ status = "okay";
+ };
+ };
+ };
+
+ ahb@80080000 {
+ usb0: usb@80080000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_id_pins_a>;
+ vbus-supply = <®_usb0_vbus>;
+ status = "okay";
+ };
+
+ usb1: usb@80090000 {
+ vbus-supply = <®_usb1_vbus>;
+ status = "okay";
+ };
+
+ mac0: ethernet@800f0000 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac0_pins_a>;
+ phy-supply = <®_fec_3v3>;
+ phy-reset-gpios = <&gpio4 13 0>;
+ phy-reset-duration = <100>;
+ status = "okay";
+ };
+
+ mac1: ethernet@800f4000 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac1_pins_a>;
+ status = "okay";
+ };
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reg_3p3v: regulator@0 {
+ compatible = "regulator-fixed";
+ reg = <0>;
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_vddio_sd0: regulator@1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "vddio-sd0";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio3 28 0>;
+ };
+
+ reg_fec_3v3: regulator@2 {
+ compatible = "regulator-fixed";
+ reg = <2>;
+ regulator-name = "fec-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio2 15 0>;
+ };
+
+ reg_usb0_vbus: regulator@3 {
+ compatible = "regulator-fixed";
+ reg = <3>;
+ regulator-name = "usb0_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio3 9 0>;
+ enable-active-high;
+ };
+
+ reg_usb1_vbus: regulator@4 {
+ compatible = "regulator-fixed";
+ reg = <4>;
+ regulator-name = "usb1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio3 8 0>;
+ enable-active-high;
+ };
+
+ reg_lcd_3v3: regulator@5 {
+ compatible = "regulator-fixed";
+ reg = <5>;
+ regulator-name = "lcd-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio3 30 0>;
+ enable-active-high;
+ };
+
+ reg_can_3v3: regulator@6 {
+ compatible = "regulator-fixed";
+ reg = <6>;
+ regulator-name = "can-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio2 13 0>;
+ enable-active-high;
+ };
+
+ };
+
+ sound {
+ compatible = "fsl,imx28-evk-sgtl5000",
+ "fsl,mxs-audio-sgtl5000";
+ model = "imx28-evk-sgtl5000";
+ saif-controllers = <&saif0 &saif1>;
+ audio-codec = <&sgtl5000>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pin_gpio3_5>;
+
+ user {
+ label = "Heartbeat";
+ gpios = <&gpio3 5 0>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm 2 5000000>;
+ brightness-levels = <0 4 8 16 32 64 128 255>;
+ default-brightness-level = <6>;
+ };
+};
Code Review / kvmfornfv.git / blobdiff