Add the rt linux 4.1.3-rt3 as base

[kvmfornfv.git] / kernel / arch / arm / boot / dts / imx28-eukrea-mbmx283lc.dts

diff --git a/kernel/arch/arm/boot/dts/imx28-eukrea-mbmx283lc.dts b/kernel/arch/arm/boot/dts/imx28-eukrea-mbmx283lc.dts
new file mode 100644 (file)
index 0000000..7c1572c
--- /dev/null
+++ b/kernel/arch/arm/boot/dts/imx28-eukrea-mbmx283lc.dts
@@ -0,0 +1,71 @@
+/*
+ * Copyright 2013 Eukréa Electromatique <eric@eukrea.com>
+ * Copyright 2013 Eukréa Electromatique <denis@eukrea.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+/*
+ * Module contains : i.MX282 + 64MB DDR2 + NAND + Ethernet PHY + RTC
+ */
+
+/dts-v1/;
+#include "imx28-eukrea-mbmx28lc.dtsi"
+
+/ {
+       model = "Eukrea Electromatique MBMX283LC";
+       compatible = "eukrea,mbmx283lc", "eukrea,mbmx28lc", "fsl,imx28";
+
+       memory {
+               reg = <0x40000000 0x04000000>;
+       };
+};
+
+&gpmi {
+       pinctrl-names = "default";
+       pinctrl-0 = <&gpmi_pins_a>;
+       status = "okay";
+};
+
+&i2c0 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&i2c0_pins_a>;
+       status = "okay";
+
+       pcf8563: rtc@51 {
+               compatible = "nxp,pcf8563";
+               reg = <0x51>;
+       };
+};
+
+
+&mac0 {
+       phy-mode = "rmii";
+       pinctrl-names = "default";
+       pinctrl-0 = <&mac0_pins_a>;
+       phy-reset-gpios = <&gpio4 13 GPIO_ACTIVE_LOW>;
+       status = "okay";
+};
+
+&pinctrl{
+       pinctrl-names = "default";
+       pinctrl-0 = <&hog_pins_cpuimx283>;
+
+       hog_pins_cpuimx283: hog-cpuimx283@0 {
+               reg = <0>;
+               fsl,pinmux-ids = <
+                       MX28_PAD_ENET0_RX_CLK__GPIO_4_13
+                       MX28_PAD_ENET0_TX_CLK__GPIO_4_5
+               >;
+               fsl,drive-strength = <MXS_DRIVE_4mA>;
+               fsl,voltage = <MXS_VOLTAGE_HIGH>;
+               fsl,pull-up = <MXS_PULL_ENABLE>;
+       };
+};