--- /dev/null
+/*
+ * Device Tree file for OpenBlocks AX3-4 board
+ *
+ * Copyright (C) 2012 Marvell
+ *
+ * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include "armada-xp-mv78260.dtsi"
+
+/ {
+ model = "PlatHome OpenBlocks AX3-4 board";
+ compatible = "plathome,openblocks-ax3-4", "marvell,armadaxp-mv78260", "marvell,armadaxp", "marvell,armada-370-xp";
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0 0x00000000 0 0x40000000>; /* 1 GB soldered on */
+ };
+
+ soc {
+ ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xd0000000 0x100000
+ MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000
+ MBUS_ID(0x01, 0x2f) 0 0 0xf0000000 0x8000000>;
+
+ devbus-bootcs {
+ status = "okay";
+
+ /* Device Bus parameters are required */
+
+ /* Read parameters */
+ devbus,bus-width = <16>;
+ devbus,turn-off-ps = <60000>;
+ devbus,badr-skew-ps = <0>;
+ devbus,acc-first-ps = <124000>;
+ devbus,acc-next-ps = <248000>;
+ devbus,rd-setup-ps = <0>;
+ devbus,rd-hold-ps = <0>;
+
+ /* Write parameters */
+ devbus,sync-enable = <0>;
+ devbus,wr-high-ps = <60000>;
+ devbus,wr-low-ps = <60000>;
+ devbus,ale-wr-ps = <60000>;
+
+ /* NOR 128 MiB */
+ nor@0 {
+ compatible = "cfi-flash";
+ reg = <0 0x8000000>;
+ bank-width = <2>;
+ };
+ };
+
+ pcie-controller {
+ status = "okay";
+ /* Internal mini-PCIe connector */
+ pcie@1,0 {
+ /* Port 0, Lane 0 */
+ status = "okay";
+ };
+ };
+
+ internal-regs {
+ rtc@10300 {
+ /* No crystal connected to the internal RTC */
+ status = "disabled";
+ };
+ serial@12000 {
+ status = "okay";
+ };
+ serial@12100 {
+ status = "okay";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins>;
+
+ red_led {
+ label = "red_led";
+ gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+
+ yellow_led {
+ label = "yellow_led";
+ gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+
+ green_led {
+ label = "green_led";
+ gpios = <&gpio1 21 GPIO_ACTIVE_LOW>;
+ default-state = "keep";
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ button@1 {
+ label = "Init Button";
+ linux,code = <KEY_POWER>;
+ gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ mdio {
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ };
+
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+
+ phy2: ethernet-phy@2 {
+ reg = <2>;
+ };
+
+ phy3: ethernet-phy@3 {
+ reg = <3>;
+ };
+ };
+
+ ethernet@70000 {
+ status = "okay";
+ phy = <&phy0>;
+ phy-mode = "sgmii";
+ };
+ ethernet@74000 {
+ status = "okay";
+ phy = <&phy1>;
+ phy-mode = "sgmii";
+ };
+ ethernet@30000 {
+ status = "okay";
+ phy = <&phy2>;
+ phy-mode = "sgmii";
+ };
+ ethernet@34000 {
+ status = "okay";
+ phy = <&phy3>;
+ phy-mode = "sgmii";
+ };
+ i2c@11000 {
+ status = "okay";
+ clock-frequency = <400000>;
+ };
+ i2c@11100 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ s35390a: s35390a@30 {
+ compatible = "s35390a";
+ reg = <0x30>;
+ };
+ };
+ sata@a0000 {
+ nr-ports = <2>;
+ status = "okay";
+ };
+
+ /* Front side USB 0 */
+ usb@50000 {
+ status = "okay";
+ };
+
+ /* Front side USB 1 */
+ usb@51000 {
+ status = "okay";
+ };
+ };
+ };
+};
+
+&pinctrl {
+ led_pins: led-pins-0 {
+ marvell,pins = "mpp49", "mpp51", "mpp53";
+ marvell,function = "gpio";
+ };
+};
Code Review / kvmfornfv.git / blobdiff