These changes are the raw update to linux-4.4.6-rt14. Kernel sources

[kvmfornfv.git] / kernel / Documentation / devicetree / bindings / video / adi,adv7511.txt

diff --git a/kernel/Documentation/devicetree/bindings/video/adi,adv7511.txt b/kernel/Documentation/devicetree/bindings/video/adi,adv7511.txt
deleted file mode 100644 (file)
index 96c25ee..0000000
--- a/kernel/Documentation/devicetree/bindings/video/adi,adv7511.txt
+++ /dev/null
@@ -1,88 +0,0 @@
-Analog Device ADV7511(W)/13 HDMI Encoders
------------------------------------------
-
-The ADV7511, ADV7511W and ADV7513 are HDMI audio and video transmitters
-compatible with HDMI 1.4 and DVI 1.0. They support color space conversion,
-S/PDIF, CEC and HDCP.
-
-Required properties:
-
-- compatible: Should be one of "adi,adv7511", "adi,adv7511w" or "adi,adv7513"
-- reg: I2C slave address
-
-The ADV7511 supports a large number of input data formats that differ by their
-color depth, color format, clock mode, bit justification and random
-arrangement of components on the data bus. The combination of the following
-properties describe the input and map directly to the video input tables of the
-ADV7511 datasheet that document all the supported combinations.
-
-- adi,input-depth: Number of bits per color component at the input (8, 10 or
-  12).
-- adi,input-colorspace: The input color space, one of "rgb", "yuv422" or
-  "yuv444".
-- adi,input-clock: The input clock type, one of "1x" (one clock cycle per
-  pixel), "2x" (two clock cycles per pixel), "ddr" (one clock cycle per pixel,
-  data driven on both edges).
-
-The following input format properties are required except in "rgb 1x" and
-"yuv444 1x" modes, in which case they must not be specified.
-
-- adi,input-style: The input components arrangement variant (1, 2 or 3), as
-  listed in the input format tables in the datasheet.
-- adi,input-justification: The input bit justification ("left", "evenly",
-  "right").
-
-Optional properties:
-
-- interrupts: Specifier for the ADV7511 interrupt
-- pd-gpios: Specifier for the GPIO connected to the power down signal
-
-- adi,clock-delay: Video data clock delay relative to the pixel clock, in ps
-  (-1200 ps .. 1600 ps). Defaults to no delay.
-- adi,embedded-sync: The input uses synchronization signals embedded in the
-  data stream (similar to BT.656). Defaults to separate H/V synchronization
-  signals.
-
-Required nodes:
-
-The ADV7511 has two video ports. Their connections are modelled using the OF
-graph bindings specified in Documentation/devicetree/bindings/graph.txt.
-
-- Video port 0 for the RGB or YUV input
-- Video port 1 for the HDMI output
-
-
-Example
--------
-
-       adv7511w: hdmi@39 {
-               compatible = "adi,adv7511w";
-               reg = <39>;
-               interrupt-parent = <&gpio3>;
-               interrupts = <29 IRQ_TYPE_EDGE_FALLING>;
-
-               adi,input-depth = <8>;
-               adi,input-colorspace = "rgb";
-               adi,input-clock = "1x";
-               adi,input-style = <1>;
-               adi,input-justification = "evenly";
-
-               ports {
-                       #address-cells = <1>;
-                       #size-cells = <0>;
-
-                       port@0 {
-                               reg = <0>;
-                               adv7511w_in: endpoint {
-                                       remote-endpoint = <&dpi_out>;
-                               };
-                       };
-
-                       port@1 {
-                               reg = <1>;
-                               adv7511_out: endpoint {
-                                       remote-endpoint = <&hdmi_connector_in>;
-                               };
-                       };
-               };
-       };