These changes are the raw update to linux-4.4.6-rt14. Kernel sources

[kvmfornfv.git] / kernel / Documentation / devicetree / bindings / reset / nxp,lpc1850-rgu.txt

diff --git a/kernel/Documentation/devicetree/bindings/reset/nxp,lpc1850-rgu.txt b/kernel/Documentation/devicetree/bindings/reset/nxp,lpc1850-rgu.txt
new file mode 100644 (file)
index 0000000..b4e96a2
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/reset/nxp,lpc1850-rgu.txt
@@ -0,0 +1,84 @@
+NXP LPC1850  Reset Generation Unit (RGU)
+========================================
+
+Please also refer to reset.txt in this directory for common reset
+controller binding usage.
+
+Required properties:
+- compatible: Should be "nxp,lpc1850-rgu"
+- reg: register base and length
+- clocks: phandle and clock specifier to RGU clocks
+- clock-names: should contain "delay" and "reg"
+- #reset-cells: should be 1
+
+See table below for valid peripheral reset numbers. Numbers not
+in the table below are either reserved or not applicable for
+normal operation.
+
+Reset  Peripheral
+  9    System control unit (SCU)
+ 12    ARM Cortex-M0 subsystem core (LPC43xx only)
+ 13    CPU core
+ 16    LCD controller
+ 17    USB0
+ 18    USB1
+ 19    DMA
+ 20    SDIO
+ 21    External memory controller (EMC)
+ 22    Ethernet
+ 25    Flash bank A
+ 27    EEPROM
+ 28    GPIO
+ 29    Flash bank B
+ 32    Timer0
+ 33    Timer1
+ 34    Timer2
+ 35    Timer3
+ 36    Repetitive Interrupt timer (RIT)
+ 37    State Configurable Timer (SCT)
+ 38    Motor control PWM (MCPWM)
+ 39    QEI
+ 40    ADC0
+ 41    ADC1
+ 42    DAC
+ 44    USART0
+ 45    UART1
+ 46    USART2
+ 47    USART3
+ 48    I2C0
+ 49    I2C1
+ 50    SSP0
+ 51    SSP1
+ 52    I2S0 and I2S1
+ 53    Serial Flash Interface (SPIFI)
+ 54    C_CAN1
+ 55    C_CAN0
+ 56    ARM Cortex-M0 application core (LPC4370 only)
+ 57    SGPIO (LPC43xx only)
+ 58    SPI (LPC43xx only)
+ 60    ADCHS (12-bit ADC) (LPC4370 only)
+
+Refer to NXP LPC18xx or LPC43xx user manual for more details about
+the reset signals and the connected block/peripheral.
+
+Reset provider example:
+rgu: reset-controller@40053000 {
+       compatible = "nxp,lpc1850-rgu";
+       reg = <0x40053000 0x1000>;
+       clocks = <&cgu BASE_SAFE_CLK>, <&ccu1 CLK_CPU_BUS>;
+       clock-names = "delay", "reg";
+       #reset-cells = <1>;
+};
+
+Reset consumer example:
+mac: ethernet@40010000 {
+       compatible = "nxp,lpc1850-dwmac", "snps,dwmac-3.611", "snps,dwmac";
+       reg = <0x40010000 0x2000>;
+       interrupts = <5>;
+       interrupt-names = "macirq";
+       clocks = <&ccu1 CLK_CPU_ETHERNET>;
+       clock-names = "stmmaceth";
+       resets = <&rgu 22>;
+       reset-names = "stmmaceth";
+       status = "disabled";
+};