--- /dev/null
+* Mediatek MT65XX Pin Controller
+
+The Mediatek's Pin controller is used to control SoC pins.
+
+Required properties:
+- compatible: value should be either of the following.
+ (a) "mediatek,mt8135-pinctrl", compatible with mt8135 pinctrl.
+- mediatek,pctl-regmap: Should be a phandle of the syscfg node.
+- pins-are-numbered: Specify the subnodes are using numbered pinmux to
+ specify pins.
+- gpio-controller : Marks the device node as a gpio controller.
+- #gpio-cells: number of cells in GPIO specifier. Since the generic GPIO
+ binding is used, the amount of cells must be specified as 2. See the below
+ mentioned gpio binding representation for description of particular cells.
+
+ Eg: <&pio 6 0>
+ <[phandle of the gpio controller node]
+ [line number within the gpio controller]
+ [flags]>
+
+ Values for gpio specifier:
+ - Line number: is a value between 0 to 202.
+ - Flags: bit field of flags, as defined in <dt-bindings/gpio/gpio.h>.
+ Only the following flags are supported:
+ 0 - GPIO_ACTIVE_HIGH
+ 1 - GPIO_ACTIVE_LOW
+- reg: physicall address base for EINT registers
+- interrupt-controller: Marks the device node as an interrupt controller
+- #interrupt-cells: Should be two.
+- interrupts : The interrupt outputs from the controller.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices.
+
+Subnode format
+A pinctrl node should contain at least one subnodes representing the
+pinctrl groups available on the machine. Each subnode will list the
+pins it needs, and how they should be configured, with regard to muxer
+configuration, pullups, drive strength, input enable/disable and input schmitt.
+
+ node {
+ pinmux = <PIN_NUMBER_PINMUX>;
+ GENERIC_PINCONFIG;
+ };
+
+Required properties:
+- pinmux: integer array, represents gpio pin number and mux setting.
+ Supported pin number and mux varies for different SoCs, and are defined
+ as macros in boot/dts/<soc>-pinfunc.h directly.
+
+Optional properties:
+- GENERIC_PINCONFIG: is the generic pinconfig options to use, bias-disable,
+ bias-pull-down, bias-pull-up, input-enable, input-disable, output-low, output-high,
+ input-schmitt-enable, input-schmitt-disable and drive-strength are valid.
+
+ Some special pins have extra pull up strength, there are R0 and R1 pull-up
+ resistors available, but for user, it's only need to set R1R0 as 00, 01, 10 or 11.
+ So when config bias-pull-up, it support arguments for those special pins.
+ Some macros have been defined for this usage, such as MTK_PUPD_SET_R1R0_00.
+ See dt-bindings/pinctrl/mt65xx.h.
+
+ When config drive-strength, it can support some arguments, such as
+ MTK_DRIVE_4mA, MTK_DRIVE_6mA, etc. See dt-bindings/pinctrl/mt65xx.h.
+
+Examples:
+
+#include "mt8135-pinfunc.h"
+
+...
+{
+ syscfg_pctl_a: syscfg_pctl_a@10005000 {
+ compatible = "mediatek,mt8135-pctl-a-syscfg", "syscon";
+ reg = <0 0x10005000 0 0x1000>;
+ };
+
+ syscfg_pctl_b: syscfg_pctl_b@1020C020 {
+ compatible = "mediatek,mt8135-pctl-b-syscfg", "syscon";
+ reg = <0 0x1020C020 0 0x1000>;
+ };
+
+ pinctrl@01c20800 {
+ compatible = "mediatek,mt8135-pinctrl";
+ reg = <0 0x1000B000 0 0x1000>;
+ mediatek,pctl-regmap = <&syscfg_pctl_a &syscfg_pctl_b>;
+ pins-are-numbered;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
+
+ i2c0_pins_a: i2c0@0 {
+ pins1 {
+ pinmux = <MT8135_PIN_100_SDA0__FUNC_SDA0>,
+ <MT8135_PIN_101_SCL0__FUNC_SCL0>;
+ bias-disable;
+ };
+ };
+
+ i2c1_pins_a: i2c1@0 {
+ pins {
+ pinmux = <MT8135_PIN_195_SDA1__FUNC_SDA1>,
+ <MT8135_PIN_196_SCL1__FUNC_SCL1>;
+ bias-pull-up = <55>;
+ };
+ };
+
+ i2c2_pins_a: i2c2@0 {
+ pins1 {
+ pinmux = <MT8135_PIN_193_SDA2__FUNC_SDA2>;
+ bias-pull-down;
+ };
+
+ pins2 {
+ pinmux = <MT8135_PIN_49_WATCHDOG__FUNC_GPIO49>;
+ bias-pull-up;
+ };
+ };
+
+ i2c3_pins_a: i2c3@0 {
+ pins1 {
+ pinmux = <MT8135_PIN_40_DAC_CLK__FUNC_GPIO40>,
+ <MT8135_PIN_41_DAC_WS__FUNC_GPIO41>;
+ bias-pull-up = <55>;
+ };
+
+ pins2 {
+ pinmux = <MT8135_PIN_35_SCL3__FUNC_SCL3>,
+ <MT8135_PIN_36_SDA3__FUNC_SDA3>;
+ output-low;
+ bias-pull-up = <55>;
+ };
+
+ pins3 {
+ pinmux = <MT8135_PIN_57_JTCK__FUNC_GPIO57>,
+ <MT8135_PIN_60_JTDI__FUNC_JTDI>;
+ drive-strength = <32>;
+ };
+ };
+
+ ...
+ }
+};
Code Review / kvmfornfv.git / blobdiff