Add the rt linux 4.1.3-rt3 as base

[kvmfornfv.git] / kernel / Documentation / devicetree / bindings / pinctrl / meson,pinctrl.txt

diff --git a/kernel/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt b/kernel/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt
new file mode 100644 (file)
index 0000000..3f6a524
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt
@@ -0,0 +1,96 @@
+== Amlogic Meson pinmux controller ==
+
+Required properties for the root node:
+ - compatible: "amlogic,meson8-pinctrl" or "amlogic,meson8b-pinctrl"
+ - reg: address and size of registers controlling irq functionality
+
+=== GPIO sub-nodes ===
+
+The 2 power domains of the controller (regular and always-on) are
+represented as sub-nodes and each of them acts as a GPIO controller.
+
+Required properties for sub-nodes are:
+ - reg: should contain address and size for mux, pull-enable, pull and
+   gpio register sets
+ - reg-names: an array of strings describing the "reg" entries. Must
+   contain "mux", "pull" and "gpio". "pull-enable" is optional and
+   when it is missing the "pull" registers are used instead
+ - gpio-controller: identifies the node as a gpio controller
+ - #gpio-cells: must be 2
+
+Valid sub-node names are:
+ - "banks" for the regular domain
+ - "ao-bank" for the always-on domain
+
+=== Other sub-nodes ===
+
+Child nodes without the "gpio-controller" represent some desired
+configuration for a pin or a group. Those nodes can be pinmux nodes or
+configuration nodes.
+
+Required properties for pinmux nodes are:
+ - groups: a list of pinmux groups. The list of all available groups
+   depends on the SoC and can be found in driver sources.
+ - function: the name of a function to activate for the specified set
+   of groups. The list of all available functions depends on the SoC
+   and can be found in driver sources.
+
+Required properties for configuration nodes:
+ - pins: a list of pin names
+
+Configuration nodes support the generic properties "bias-disable",
+"bias-pull-up" and "bias-pull-down", described in file
+pinctrl-bindings.txt
+
+=== Example ===
+
+       pinctrl: pinctrl@c1109880 {
+               compatible = "amlogic,meson8-pinctrl";
+               reg = <0xc1109880 0x10>;
+               #address-cells = <1>;
+               #size-cells = <1>;
+               ranges;
+
+               gpio: banks@c11080b0 {
+                       reg = <0xc11080b0 0x28>,
+                             <0xc11080e8 0x18>,
+                             <0xc1108120 0x18>,
+                             <0xc1108030 0x30>;
+                       reg-names = "mux", "pull", "pull-enable", "gpio";
+                       gpio-controller;
+                       #gpio-cells = <2>;
+               };
+
+               gpio_ao: ao-bank@c1108030 {
+                       reg = <0xc8100014 0x4>,
+                             <0xc810002c 0x4>,
+                             <0xc8100024 0x8>;
+                       reg-names = "mux", "pull", "gpio";
+                       gpio-controller;
+                       #gpio-cells = <2>;
+               };
+
+               nand {
+                       mux {
+                               groups = "nand_io", "nand_io_ce0", "nand_io_ce1",
+                                        "nand_io_rb0", "nand_ale", "nand_cle",
+                                        "nand_wen_clk", "nand_ren_clk", "nand_dqs",
+                                        "nand_ce2", "nand_ce3";
+                               function = "nand";
+                       };
+               };
+
+               uart_ao_a {
+                       mux {
+                               groups = "uart_tx_ao_a", "uart_rx_ao_a",
+                                        "uart_cts_ao_a", "uart_rts_ao_a";
+                               function = "uart_ao";
+                       };
+
+                       conf {
+                               pins = "GPIOAO_0", "GPIOAO_1",
+                                      "GPIOAO_2", "GPIOAO_3";
+                               bias-disable;
+                       };
+               };
+       };