Add the rt linux 4.1.3-rt3 as base

[kvmfornfv.git] / kernel / Documentation / devicetree / bindings / phy / apm-xgene-phy.txt

diff --git a/kernel/Documentation/devicetree/bindings/phy/apm-xgene-phy.txt b/kernel/Documentation/devicetree/bindings/phy/apm-xgene-phy.txt
new file mode 100644 (file)
index 0000000..5f3a65a
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/phy/apm-xgene-phy.txt
@@ -0,0 +1,79 @@
+* APM X-Gene 15Gbps Multi-purpose PHY nodes
+
+PHY nodes are defined to describe on-chip 15Gbps Multi-purpose PHY. Each
+PHY (pair of lanes) has its own node.
+
+Required properties:
+- compatible           : Shall be "apm,xgene-phy".
+- reg                  : PHY memory resource is the SDS PHY access resource.
+- #phy-cells           : Shall be 1 as it expects one argument for setting
+                         the mode of the PHY. Possible values are 0 (SATA),
+                         1 (SGMII), 2 (PCIe), 3 (USB), and 4 (XFI).
+
+Optional properties:
+- status               : Shall be "ok" if enabled or "disabled" if disabled.
+                         Default is "ok".
+- clocks               : Reference to the clock entry.
+- apm,tx-eye-tuning    : Manual control to fine tune the capture of the serial
+                         bit lines from the automatic calibrated position.
+                         Two set of 3-tuple setting for each (up to 3)
+                         supported link speed on the host. Range from 0 to
+                         127 in unit of one bit period. Default is 10.
+- apm,tx-eye-direction : Eye tuning manual control direction. 0 means sample
+                         data earlier than the nominal sampling point. 1 means
+                         sample data later than the nominal sampling point.
+                         Two set of 3-tuple setting for each (up to 3)
+                         supported link speed on the host. Default is 0.
+- apm,tx-boost-gain    : Frequency boost AC (LSB 3-bit) and DC (2-bit)
+                         gain control. Two set of 3-tuple setting for each
+                         (up to 3) supported link speed on the host. Range is
+                         between 0 to 31 in unit of dB. Default is 3.
+- apm,tx-amplitude     : Amplitude control. Two set of 3-tuple setting for
+                         each (up to 3) supported link speed on the host.
+                         Range is between 0 to 199500 in unit of uV.
+                         Default is 199500 uV.
+- apm,tx-pre-cursor1   : 1st pre-cursor emphasis taps control. Two set of
+                         3-tuple setting for each (up to 3) supported link
+                         speed on the host. Range is 0 to 273000 in unit of
+                         uV. Default is 0.
+- apm,tx-pre-cursor2   : 2st pre-cursor emphasis taps control. Two set of
+                         3-tuple setting for each (up to 3) supported link
+                         speed on the host. Range is 0 to 127400 in unit uV.
+                         Default is 0x0.
+- apm,tx-post-cursor   : Post-cursor emphasis taps control. Two set of
+                         3-tuple setting for Gen1, Gen2, and Gen3. Range is
+                         between 0 to 0x1f in unit of 18.2mV. Default is 0xf.
+- apm,tx-speed         : Tx operating speed. One set of 3-tuple for each
+                         supported link speed on the host.
+                          0 = 1-2Gbps
+                          1 = 2-4Gbps (1st tuple default)
+                          2 = 4-8Gbps
+                          3 = 8-15Gbps (2nd tuple default)
+                          4 = 2.5-4Gbps
+                          5 = 4-5Gbps
+                          6 = 5-6Gbps
+                          7 = 6-16Gbps (3rd tuple default)
+
+NOTE: PHY override parameters are board specific setting.
+
+Example:
+               phy1: phy@1f21a000 {
+                       compatible = "apm,xgene-phy";
+                       reg = <0x0 0x1f21a000 0x0 0x100>;
+                       #phy-cells = <1>;
+                       status = "disabled";
+               };
+
+               phy2: phy@1f22a000 {
+                       compatible = "apm,xgene-phy";
+                       reg = <0x0 0x1f22a000 0x0 0x100>;
+                       #phy-cells = <1>;
+                       status = "ok";
+               };
+
+               phy3: phy@1f23a000 {
+                       compatible = "apm,xgene-phy";
+                       reg = <0x0 0x1f23a000 0x0 0x100>;
+                       #phy-cells = <1>;
+                       status = "ok";
+               };