--- /dev/null
+* MDIO IO device
+
+The MDIO is a bus to which the PHY devices are connected. For each
+device that exists on this bus, a child node should be created. See
+the definition of the PHY node in booting-without-of.txt for an example
+of how to define a PHY.
+
+Required properties:
+ - reg : Offset and length of the register set for the device
+ - compatible : Should define the compatible device type for the
+ mdio. Currently supported strings/devices are:
+ - "fsl,gianfar-tbi"
+ - "fsl,gianfar-mdio"
+ - "fsl,etsec2-tbi"
+ - "fsl,etsec2-mdio"
+ - "fsl,ucc-mdio"
+ - "fsl,fman-mdio"
+ When device_type is "mdio", the following strings are also considered:
+ - "gianfar"
+ - "ucc_geth_phy"
+
+Example:
+
+ mdio@24520 {
+ reg = <24520 20>;
+ compatible = "fsl,gianfar-mdio";
+
+ ethernet-phy@0 {
+ ......
+ };
+ };
+
+* TBI Internal MDIO bus
+
+As of this writing, every tsec is associated with an internal TBI PHY.
+This PHY is accessed through the local MDIO bus. These buses are defined
+similarly to the mdio buses, except they are compatible with "fsl,gianfar-tbi".
+The TBI PHYs underneath them are similar to normal PHYs, but the reg property
+is considered instructive, rather than descriptive. The reg property should
+be chosen so it doesn't interfere with other PHYs on the bus.
+
+* Gianfar-compatible ethernet nodes
+
+Properties:
+
+ - device_type : Should be "network"
+ - model : Model of the device. Can be "TSEC", "eTSEC", or "FEC"
+ - compatible : Should be "gianfar"
+ - reg : Offset and length of the register set for the device
+ - interrupts : For FEC devices, the first interrupt is the device's
+ interrupt. For TSEC and eTSEC devices, the first interrupt is
+ transmit, the second is receive, and the third is error.
+ - phy-handle : See ethernet.txt file in the same directory.
+ - fixed-link : See fixed-link.txt in the same directory.
+ - phy-connection-type : See ethernet.txt file in the same directory.
+ This property is only really needed if the connection is of type
+ "rgmii-id", as all other connection types are detected by hardware.
+ - fsl,magic-packet : If present, indicates that the hardware supports
+ waking up via magic packet.
+ - bd-stash : If present, indicates that the hardware supports stashing
+ buffer descriptors in the L2.
+ - rx-stash-len : Denotes the number of bytes of a received buffer to stash
+ in the L2.
+ - rx-stash-idx : Denotes the index of the first byte from the received
+ buffer to stash in the L2.
+
+Example:
+ ethernet@24000 {
+ device_type = "network";
+ model = "TSEC";
+ compatible = "gianfar";
+ reg = <0x24000 0x1000>;
+ local-mac-address = [ 00 E0 0C 00 73 00 ];
+ interrupts = <29 2 30 2 34 2>;
+ interrupt-parent = <&mpic>;
+ phy-handle = <&phy0>
+ };
+
+* Gianfar PTP clock nodes
+
+General Properties:
+
+ - compatible Should be "fsl,etsec-ptp"
+ - reg Offset and length of the register set for the device
+ - interrupts There should be at least two interrupts. Some devices
+ have as many as four PTP related interrupts.
+
+Clock Properties:
+
+ - fsl,cksel Timer reference clock source.
+ - fsl,tclk-period Timer reference clock period in nanoseconds.
+ - fsl,tmr-prsc Prescaler, divides the output clock.
+ - fsl,tmr-add Frequency compensation value.
+ - fsl,tmr-fiper1 Fixed interval period pulse generator.
+ - fsl,tmr-fiper2 Fixed interval period pulse generator.
+ - fsl,max-adj Maximum frequency adjustment in parts per billion.
+
+ These properties set the operational parameters for the PTP
+ clock. You must choose these carefully for the clock to work right.
+ Here is how to figure good values:
+
+ TimerOsc = selected reference clock MHz
+ tclk_period = desired clock period nanoseconds
+ NominalFreq = 1000 / tclk_period MHz
+ FreqDivRatio = TimerOsc / NominalFreq (must be greater that 1.0)
+ tmr_add = ceil(2^32 / FreqDivRatio)
+ OutputClock = NominalFreq / tmr_prsc MHz
+ PulseWidth = 1 / OutputClock microseconds
+ FiperFreq1 = desired frequency in Hz
+ FiperDiv1 = 1000000 * OutputClock / FiperFreq1
+ tmr_fiper1 = tmr_prsc * tclk_period * FiperDiv1 - tclk_period
+ max_adj = 1000000000 * (FreqDivRatio - 1.0) - 1
+
+ The calculation for tmr_fiper2 is the same as for tmr_fiper1. The
+ driver expects that tmr_fiper1 will be correctly set to produce a 1
+ Pulse Per Second (PPS) signal, since this will be offered to the PPS
+ subsystem to synchronize the Linux clock.
+
+ Reference clock source is determined by the value, which is holded
+ in CKSEL bits in TMR_CTRL register. "fsl,cksel" property keeps the
+ value, which will be directly written in those bits, that is why,
+ according to reference manual, the next clock sources can be used:
+
+ <0> - external high precision timer reference clock (TSEC_TMR_CLK
+ input is used for this purpose);
+ <1> - eTSEC system clock;
+ <2> - eTSEC1 transmit clock;
+ <3> - RTC clock input.
+
+ When this attribute is not used, eTSEC system clock will serve as
+ IEEE 1588 timer reference clock.
+
+Example:
+
+ ptp_clock@24E00 {
+ compatible = "fsl,etsec-ptp";
+ reg = <0x24E00 0xB0>;
+ interrupts = <12 0x8 13 0x8>;
+ interrupt-parent = < &ipic >;
+ fsl,cksel = <1>;
+ fsl,tclk-period = <10>;
+ fsl,tmr-prsc = <100>;
+ fsl,tmr-add = <0x999999A4>;
+ fsl,tmr-fiper1 = <0x3B9AC9F6>;
+ fsl,tmr-fiper2 = <0x00018696>;
+ fsl,max-adj = <659999998>;
+ };
Code Review / kvmfornfv.git / blobdiff