Add the rt linux 4.1.3-rt3 as base

[kvmfornfv.git] / kernel / Documentation / devicetree / bindings / dma / xilinx / xilinx_vdma.txt

diff --git a/kernel/Documentation/devicetree/bindings/dma/xilinx/xilinx_vdma.txt b/kernel/Documentation/devicetree/bindings/dma/xilinx/xilinx_vdma.txt
new file mode 100644 (file)
index 0000000..e4c4d47
--- /dev/null
+++ b/kernel/Documentation/devicetree/bindings/dma/xilinx/xilinx_vdma.txt
@@ -0,0 +1,75 @@
+Xilinx AXI VDMA engine, it does transfers between memory and video devices.
+It can be configured to have one channel or two channels. If configured
+as two channels, one is to transmit to the video device and another is
+to receive from the video device.
+
+Required properties:
+- compatible: Should be "xlnx,axi-vdma-1.00.a"
+- #dma-cells: Should be <1>, see "dmas" property below
+- reg: Should contain VDMA registers location and length.
+- xlnx,num-fstores: Should be the number of framebuffers as configured in h/w.
+- dma-channel child node: Should have at least one channel and can have up to
+       two channels per device. This node specifies the properties of each
+       DMA channel (see child node properties below).
+
+Optional properties:
+- xlnx,include-sg: Tells configured for Scatter-mode in
+       the hardware.
+- xlnx,flush-fsync: Tells which channel to Flush on Frame sync.
+       It takes following values:
+       {1}, flush both channels
+       {2}, flush mm2s channel
+       {3}, flush s2mm channel
+
+Required child node properties:
+- compatible: It should be either "xlnx,axi-vdma-mm2s-channel" or
+       "xlnx,axi-vdma-s2mm-channel".
+- interrupts: Should contain per channel VDMA interrupts.
+- xlnx,datawidth: Should contain the stream data width, take values
+       {32,64...1024}.
+
+Optional child node properties:
+- xlnx,include-dre: Tells hardware is configured for Data
+       Realignment Engine.
+- xlnx,genlock-mode: Tells Genlock synchronization is
+       enabled/disabled in hardware.
+
+Example:
+++++++++
+
+axi_vdma_0: axivdma@40030000 {
+       compatible = "xlnx,axi-vdma-1.00.a";
+       #dma_cells = <1>;
+       reg = < 0x40030000 0x10000 >;
+       xlnx,num-fstores = <0x8>;
+       xlnx,flush-fsync = <0x1>;
+       dma-channel@40030000 {
+               compatible = "xlnx,axi-vdma-mm2s-channel";
+               interrupts = < 0 54 4 >;
+               xlnx,datawidth = <0x40>;
+       } ;
+       dma-channel@40030030 {
+               compatible = "xlnx,axi-vdma-s2mm-channel";
+               interrupts = < 0 53 4 >;
+               xlnx,datawidth = <0x40>;
+       } ;
+} ;
+
+
+* DMA client
+
+Required properties:
+- dmas: a list of <[Video DMA device phandle] [Channel ID]> pairs,
+       where Channel ID is '0' for write/tx and '1' for read/rx
+       channel.
+- dma-names: a list of DMA channel names, one per "dmas" entry
+
+Example:
+++++++++
+
+vdmatest_0: vdmatest@0 {
+       compatible ="xlnx,axi-vdma-test-1.00.a";
+       dmas = <&axi_vdma_0 0
+               &axi_vdma_0 1>;
+       dma-names = "vdma0", "vdma1";
+} ;