+ /* Enable override for coefficients. */
+ status = ixgbe_read_iosf_sb_reg_x550(hw,
+ IXGBE_KRM_TX_COEFF_CTRL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val);
+ if (status)
+ return status;
+
+ reg_val |= IXGBE_KRM_TX_COEFF_CTRL_1_OVRRD_EN;
+ reg_val |= IXGBE_KRM_TX_COEFF_CTRL_1_CZERO_EN;
+ reg_val |= IXGBE_KRM_TX_COEFF_CTRL_1_CPLUS1_OVRRD_EN;
+ reg_val |= IXGBE_KRM_TX_COEFF_CTRL_1_CMINUS1_OVRRD_EN;
+ status = ixgbe_write_iosf_sb_reg_x550(hw,
+ IXGBE_KRM_TX_COEFF_CTRL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val);
+ if (status)
+ return status;
+
+ /* Toggle port SW reset by AN reset. */
+ status = ixgbe_read_iosf_sb_reg_x550(hw,
+ IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val);
+ if (status)
+ return status;
+
+ reg_val |= IXGBE_KRM_LINK_CTRL_1_TETH_AN_RESTART;
+ status = ixgbe_write_iosf_sb_reg_x550(hw,
+ IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val);
+
+ return status;
+}
+
+/**
+ * ixgbe_supported_sfp_modules_X550em - Check if SFP module type is supported
+ * @hw: pointer to hardware structure
+ * @linear: true if SFP module is linear
+ */
+static s32 ixgbe_supported_sfp_modules_X550em(struct ixgbe_hw *hw, bool *linear)
+{
+ switch (hw->phy.sfp_type) {
+ case ixgbe_sfp_type_not_present:
+ return IXGBE_ERR_SFP_NOT_PRESENT;
+ case ixgbe_sfp_type_da_cu_core0:
+ case ixgbe_sfp_type_da_cu_core1:
+ *linear = true;
+ break;
+ case ixgbe_sfp_type_srlr_core0:
+ case ixgbe_sfp_type_srlr_core1:
+ case ixgbe_sfp_type_da_act_lmt_core0:
+ case ixgbe_sfp_type_da_act_lmt_core1:
+ case ixgbe_sfp_type_1g_sx_core0:
+ case ixgbe_sfp_type_1g_sx_core1:
+ case ixgbe_sfp_type_1g_lx_core0:
+ case ixgbe_sfp_type_1g_lx_core1:
+ *linear = false;
+ break;
+ case ixgbe_sfp_type_unknown:
+ case ixgbe_sfp_type_1g_cu_core0:
+ case ixgbe_sfp_type_1g_cu_core1:
+ default:
+ return IXGBE_ERR_SFP_NOT_SUPPORTED;
+ }
+
+ return 0;
+}
+
+/**
+ * ixgbe_setup_mac_link_sfp_x550em - Configure the KR PHY for SFP.
+ * @hw: pointer to hardware structure
+ *
+ * Configures the extern PHY and the integrated KR PHY for SFP support.
+ */
+static s32
+ixgbe_setup_mac_link_sfp_x550em(struct ixgbe_hw *hw,
+ ixgbe_link_speed speed,
+ __always_unused bool autoneg_wait_to_complete)
+{
+ s32 status;
+ u16 slice, value;
+ bool setup_linear = false;
+
+ /* Check if SFP module is supported and linear */
+ status = ixgbe_supported_sfp_modules_X550em(hw, &setup_linear);
+
+ /* If no SFP module present, then return success. Return success since
+ * there is no reason to configure CS4227 and SFP not present error is
+ * not accepted in the setup MAC link flow.
+ */
+ if (status == IXGBE_ERR_SFP_NOT_PRESENT)
+ return 0;
+
+ if (status)
+ return status;
+
+ /* Configure CS4227 LINE side to 10G SR. */
+ slice = IXGBE_CS4227_LINE_SPARE22_MSB + (hw->bus.lan_id << 12);
+ value = IXGBE_CS4227_SPEED_10G;
+ status = ixgbe_write_i2c_combined_generic(hw, IXGBE_CS4227, slice,
+ value);
+
+ /* Configure CS4227 for HOST connection rate then type. */
+ slice = IXGBE_CS4227_HOST_SPARE22_MSB + (hw->bus.lan_id << 12);
+ value = speed & IXGBE_LINK_SPEED_10GB_FULL ?
+ IXGBE_CS4227_SPEED_10G : IXGBE_CS4227_SPEED_1G;
+ status = ixgbe_write_i2c_combined_generic(hw, IXGBE_CS4227, slice,
+ value);
+
+ slice = IXGBE_CS4227_HOST_SPARE24_LSB + (hw->bus.lan_id << 12);
+ if (setup_linear)
+ value = (IXGBE_CS4227_EDC_MODE_CX1 << 1) | 1;
+ else
+ value = (IXGBE_CS4227_EDC_MODE_SR << 1) | 1;
+ status = ixgbe_write_i2c_combined_generic(hw, IXGBE_CS4227, slice,
+ value);
+
+ /* If internal link mode is XFI, then setup XFI internal link. */
+ if (!(hw->phy.nw_mng_if_sel & IXGBE_NW_MNG_IF_SEL_INT_PHY_MODE))
+ status = ixgbe_setup_ixfi_x550em(hw, &speed);
+
+ return status;
+}
+
+/**
+ * ixgbe_setup_mac_link_t_X550em - Sets the auto advertised link speed
+ * @hw: pointer to hardware structure
+ * @speed: new link speed
+ * @autoneg_wait_to_complete: true when waiting for completion is needed
+ *
+ * Setup internal/external PHY link speed based on link speed, then set
+ * external PHY auto advertised link speed.
+ *
+ * Returns error status for any failure
+ **/
+static s32 ixgbe_setup_mac_link_t_X550em(struct ixgbe_hw *hw,
+ ixgbe_link_speed speed,
+ bool autoneg_wait)
+{
+ s32 status;
+ ixgbe_link_speed force_speed;
+
+ /* Setup internal/external PHY link speed to iXFI (10G), unless
+ * only 1G is auto advertised then setup KX link.
+ */
+ if (speed & IXGBE_LINK_SPEED_10GB_FULL)
+ force_speed = IXGBE_LINK_SPEED_10GB_FULL;
+ else
+ force_speed = IXGBE_LINK_SPEED_1GB_FULL;
+
+ /* If internal link mode is XFI, then setup XFI internal link. */
+ if (!(hw->phy.nw_mng_if_sel & IXGBE_NW_MNG_IF_SEL_INT_PHY_MODE)) {
+ status = ixgbe_setup_ixfi_x550em(hw, &force_speed);
+
+ if (status)
+ return status;
+ }
+
+ return hw->phy.ops.setup_link_speed(hw, speed, autoneg_wait);
+}
+
+/** ixgbe_check_link_t_X550em - Determine link and speed status
+ * @hw: pointer to hardware structure
+ * @speed: pointer to link speed
+ * @link_up: true when link is up
+ * @link_up_wait_to_complete: bool used to wait for link up or not
+ *
+ * Check that both the MAC and X557 external PHY have link.
+ **/
+static s32 ixgbe_check_link_t_X550em(struct ixgbe_hw *hw,
+ ixgbe_link_speed *speed,
+ bool *link_up,
+ bool link_up_wait_to_complete)
+{
+ u32 status;
+ u16 autoneg_status;
+
+ if (hw->mac.ops.get_media_type(hw) != ixgbe_media_type_copper)
+ return IXGBE_ERR_CONFIG;
+
+ status = ixgbe_check_mac_link_generic(hw, speed, link_up,
+ link_up_wait_to_complete);
+
+ /* If check link fails or MAC link is not up, then return */
+ if (status || !(*link_up))
+ return status;
+
+ /* MAC link is up, so check external PHY link.
+ * Read this twice back to back to indicate current status.
+ */
+ status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_STATUS,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
+ &autoneg_status);
+ if (status)
+ return status;
+
+ /* If external PHY link is not up, then indicate link not up */
+ if (!(autoneg_status & IXGBE_MDIO_AUTO_NEG_LINK_STATUS))
+ *link_up = false;
+
+ return 0;
+}
+
+/** ixgbe_init_mac_link_ops_X550em - init mac link function pointers
+ * @hw: pointer to hardware structure
+ **/
+static void ixgbe_init_mac_link_ops_X550em(struct ixgbe_hw *hw)
+{
+ struct ixgbe_mac_info *mac = &hw->mac;
+
+ switch (mac->ops.get_media_type(hw)) {
+ case ixgbe_media_type_fiber:
+ /* CS4227 does not support autoneg, so disable the laser control
+ * functions for SFP+ fiber
+ */
+ mac->ops.disable_tx_laser = NULL;
+ mac->ops.enable_tx_laser = NULL;
+ mac->ops.flap_tx_laser = NULL;
+ mac->ops.setup_link = ixgbe_setup_mac_link_multispeed_fiber;
+ mac->ops.setup_mac_link = ixgbe_setup_mac_link_sfp_x550em;
+ mac->ops.set_rate_select_speed =
+ ixgbe_set_soft_rate_select_speed;
+ break;
+ case ixgbe_media_type_copper:
+ mac->ops.setup_link = ixgbe_setup_mac_link_t_X550em;
+ mac->ops.check_link = ixgbe_check_link_t_X550em;
+ break;
+ default:
+ break;
+ }
+}
+
+/** ixgbe_setup_sfp_modules_X550em - Setup SFP module
+ * @hw: pointer to hardware structure
+ */
+static s32 ixgbe_setup_sfp_modules_X550em(struct ixgbe_hw *hw)
+{
+ s32 status;
+ bool linear;
+
+ /* Check if SFP module is supported */
+ status = ixgbe_supported_sfp_modules_X550em(hw, &linear);
+ if (status)
+ return status;
+
+ ixgbe_init_mac_link_ops_X550em(hw);
+ hw->phy.ops.reset = NULL;
+
+ return 0;
+}
+
+/** ixgbe_get_link_capabilities_x550em - Determines link capabilities
+ * @hw: pointer to hardware structure
+ * @speed: pointer to link speed
+ * @autoneg: true when autoneg or autotry is enabled
+ **/
+static s32 ixgbe_get_link_capabilities_X550em(struct ixgbe_hw *hw,
+ ixgbe_link_speed *speed,
+ bool *autoneg)
+{
+ /* SFP */
+ if (hw->phy.media_type == ixgbe_media_type_fiber) {
+ /* CS4227 SFP must not enable auto-negotiation */
+ *autoneg = false;
+
+ if (hw->phy.sfp_type == ixgbe_sfp_type_1g_sx_core0 ||
+ hw->phy.sfp_type == ixgbe_sfp_type_1g_sx_core1) {
+ *speed = IXGBE_LINK_SPEED_1GB_FULL;
+ return 0;
+ }
+
+ /* Link capabilities are based on SFP */
+ if (hw->phy.multispeed_fiber)
+ *speed = IXGBE_LINK_SPEED_10GB_FULL |
+ IXGBE_LINK_SPEED_1GB_FULL;
+ else
+ *speed = IXGBE_LINK_SPEED_10GB_FULL;
+ } else {
+ *speed = IXGBE_LINK_SPEED_10GB_FULL |
+ IXGBE_LINK_SPEED_1GB_FULL;
+ *autoneg = true;
+ }
+ return 0;
+}
+
+/**
+ * ixgbe_get_lasi_ext_t_x550em - Determime external Base T PHY interrupt cause
+ * @hw: pointer to hardware structure
+ * @lsc: pointer to boolean flag which indicates whether external Base T
+ * PHY interrupt is lsc
+ *
+ * Determime if external Base T PHY interrupt cause is high temperature
+ * failure alarm or link status change.
+ *
+ * Return IXGBE_ERR_OVERTEMP if interrupt is high temperature
+ * failure alarm, else return PHY access status.
+ **/
+static s32 ixgbe_get_lasi_ext_t_x550em(struct ixgbe_hw *hw, bool *lsc)
+{
+ u32 status;
+ u16 reg;
+
+ *lsc = false;
+
+ /* Vendor alarm triggered */
+ status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_GLOBAL_CHIP_STD_INT_FLAG,
+ IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE,
+ ®);
+
+ if (status || !(reg & IXGBE_MDIO_GLOBAL_VEN_ALM_INT_EN))
+ return status;
+
+ /* Vendor Auto-Neg alarm triggered or Global alarm 1 triggered */
+ status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_GLOBAL_INT_CHIP_VEN_FLAG,
+ IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE,
+ ®);
+
+ if (status || !(reg & (IXGBE_MDIO_GLOBAL_AN_VEN_ALM_INT_EN |
+ IXGBE_MDIO_GLOBAL_ALARM_1_INT)))
+ return status;
+
+ /* High temperature failure alarm triggered */
+ status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_GLOBAL_ALARM_1,
+ IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE,
+ ®);
+
+ if (status)
+ return status;
+
+ /* If high temperature failure, then return over temp error and exit */
+ if (reg & IXGBE_MDIO_GLOBAL_ALM_1_HI_TMP_FAIL) {
+ /* power down the PHY in case the PHY FW didn't already */
+ ixgbe_set_copper_phy_power(hw, false);
+ return IXGBE_ERR_OVERTEMP;
+ }
+
+ /* Vendor alarm 2 triggered */
+ status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_GLOBAL_CHIP_STD_INT_FLAG,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE, ®);
+
+ if (status || !(reg & IXGBE_MDIO_GLOBAL_STD_ALM2_INT))
+ return status;
+
+ /* link connect/disconnect event occurred */
+ status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_VENDOR_TX_ALARM2,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE, ®);
+
+ if (status)
+ return status;
+
+ /* Indicate LSC */
+ if (reg & IXGBE_MDIO_AUTO_NEG_VEN_LSC)
+ *lsc = true;
+
+ return 0;
+}
+
+/**
+ * ixgbe_enable_lasi_ext_t_x550em - Enable external Base T PHY interrupts
+ * @hw: pointer to hardware structure
+ *
+ * Enable link status change and temperature failure alarm for the external
+ * Base T PHY
+ *
+ * Returns PHY access status
+ **/
+static s32 ixgbe_enable_lasi_ext_t_x550em(struct ixgbe_hw *hw)
+{
+ u32 status;
+ u16 reg;
+ bool lsc;
+
+ /* Clear interrupt flags */
+ status = ixgbe_get_lasi_ext_t_x550em(hw, &lsc);
+
+ /* Enable link status change alarm */
+ status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_PMA_TX_VEN_LASI_INT_MASK,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE, ®);
+ if (status)
+ return status;
+
+ reg |= IXGBE_MDIO_PMA_TX_VEN_LASI_INT_EN;
+
+ status = hw->phy.ops.write_reg(hw, IXGBE_MDIO_PMA_TX_VEN_LASI_INT_MASK,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE, reg);
+ if (status)
+ return status;
+
+ /* Enables high temperature failure alarm */
+ status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_GLOBAL_INT_MASK,
+ IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE,
+ ®);
+ if (status)
+ return status;
+
+ reg |= IXGBE_MDIO_GLOBAL_INT_HI_TEMP_EN;
+
+ status = hw->phy.ops.write_reg(hw, IXGBE_MDIO_GLOBAL_INT_MASK,
+ IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE,
+ reg);
+ if (status)
+ return status;
+
+ /* Enable vendor Auto-Neg alarm and Global Interrupt Mask 1 alarm */
+ status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_GLOBAL_INT_CHIP_VEN_MASK,
+ IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE,
+ ®);
+ if (status)
+ return status;
+
+ reg |= (IXGBE_MDIO_GLOBAL_AN_VEN_ALM_INT_EN |
+ IXGBE_MDIO_GLOBAL_ALARM_1_INT);
+
+ status = hw->phy.ops.write_reg(hw, IXGBE_MDIO_GLOBAL_INT_CHIP_VEN_MASK,
+ IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE,
+ reg);
+ if (status)
+ return status;
+
+ /* Enable chip-wide vendor alarm */
+ status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_GLOBAL_INT_CHIP_STD_MASK,
+ IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE,
+ ®);
+ if (status)
+ return status;
+
+ reg |= IXGBE_MDIO_GLOBAL_VEN_ALM_INT_EN;
+
+ status = hw->phy.ops.write_reg(hw, IXGBE_MDIO_GLOBAL_INT_CHIP_STD_MASK,
+ IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE,
+ reg);
+
+ return status;
+}
+
+/**
+ * ixgbe_handle_lasi_ext_t_x550em - Handle external Base T PHY interrupt
+ * @hw: pointer to hardware structure
+ *
+ * Handle external Base T PHY interrupt. If high temperature
+ * failure alarm then return error, else if link status change
+ * then setup internal/external PHY link
+ *
+ * Return IXGBE_ERR_OVERTEMP if interrupt is high temperature
+ * failure alarm, else return PHY access status.
+ **/
+static s32 ixgbe_handle_lasi_ext_t_x550em(struct ixgbe_hw *hw)
+{
+ struct ixgbe_phy_info *phy = &hw->phy;
+ bool lsc;
+ u32 status;
+
+ status = ixgbe_get_lasi_ext_t_x550em(hw, &lsc);