-static int mv88e6352_setup_port(struct dsa_switch *ds, int p)
-{
- int addr = REG_PORT(p);
- u16 val;
-
- /* MAC Forcing register: don't force link, speed, duplex
- * or flow control state to any particular values on physical
- * ports, but force the CPU port and all DSA ports to 1000 Mb/s
- * full duplex.
- */
- if (dsa_is_cpu_port(ds, p) || ds->dsa_port_mask & (1 << p))
- REG_WRITE(addr, 0x01, 0x003e);
- else
- REG_WRITE(addr, 0x01, 0x0003);
-
- /* Do not limit the period of time that this port can be
- * paused for by the remote end or the period of time that
- * this port can pause the remote end.
- */
- REG_WRITE(addr, 0x02, 0x0000);
-
- /* Port Control: disable Drop-on-Unlock, disable Drop-on-Lock,
- * disable Header mode, enable IGMP/MLD snooping, disable VLAN
- * tunneling, determine priority by looking at 802.1p and IP
- * priority fields (IP prio has precedence), and set STP state
- * to Forwarding.
- *
- * If this is the CPU link, use DSA or EDSA tagging depending
- * on which tagging mode was configured.
- *
- * If this is a link to another switch, use DSA tagging mode.
- *
- * If this is the upstream port for this switch, enable
- * forwarding of unknown unicasts and multicasts.
- */
- val = 0x0433;
- if (dsa_is_cpu_port(ds, p)) {
- if (ds->dst->tag_protocol == DSA_TAG_PROTO_EDSA)
- val |= 0x3300;
- else
- val |= 0x0100;
- }
- if (ds->dsa_port_mask & (1 << p))
- val |= 0x0100;
- if (p == dsa_upstream_port(ds))
- val |= 0x000c;
- REG_WRITE(addr, 0x04, val);
-
- /* Port Control 2: don't force a good FCS, set the maximum
- * frame size to 10240 bytes, don't let the switch add or
- * strip 802.1q tags, don't discard tagged or untagged frames
- * on this port, do a destination address lookup on all
- * received packets as usual, disable ARP mirroring and don't
- * send a copy of all transmitted/received frames on this port
- * to the CPU.
- */
- REG_WRITE(addr, 0x08, 0x2080);
-
- /* Egress rate control: disable egress rate control. */
- REG_WRITE(addr, 0x09, 0x0001);
-
- /* Egress rate control 2: disable egress rate control. */
- REG_WRITE(addr, 0x0a, 0x0000);
-
- /* Port Association Vector: when learning source addresses
- * of packets, add the address to the address database using
- * a port bitmap that has only the bit for this port set and
- * the other bits clear.
- */
- REG_WRITE(addr, 0x0b, 1 << p);
-
- /* Port ATU control: disable limiting the number of address
- * database entries that this port is allowed to use.
- */
- REG_WRITE(addr, 0x0c, 0x0000);
-
- /* Priority Override: disable DA, SA and VTU priority override. */
- REG_WRITE(addr, 0x0d, 0x0000);
-
- /* Port Ethertype: use the Ethertype DSA Ethertype value. */
- REG_WRITE(addr, 0x0f, ETH_P_EDSA);
-
- /* Tag Remap: use an identity 802.1p prio -> switch prio
- * mapping.
- */
- REG_WRITE(addr, 0x18, 0x3210);
-
- /* Tag Remap 2: use an identity 802.1p prio -> switch prio
- * mapping.
- */
- REG_WRITE(addr, 0x19, 0x7654);
-
- return mv88e6xxx_setup_port_common(ds, p);
-}
-
-#ifdef CONFIG_NET_DSA_HWMON
-
-static int mv88e6352_get_temp(struct dsa_switch *ds, int *temp)
-{
- int ret;
-
- *temp = 0;
-
- ret = mv88e6xxx_phy_page_read(ds, 0, 6, 27);
- if (ret < 0)
- return ret;
-
- *temp = (ret & 0xff) - 25;
-
- return 0;
-}
-
-static int mv88e6352_get_temp_limit(struct dsa_switch *ds, int *temp)
-{
- int ret;
-
- *temp = 0;
-
- ret = mv88e6xxx_phy_page_read(ds, 0, 6, 26);
- if (ret < 0)
- return ret;
-
- *temp = (((ret >> 8) & 0x1f) * 5) - 25;
-
- return 0;
-}
-
-static int mv88e6352_set_temp_limit(struct dsa_switch *ds, int temp)
-{
- int ret;
-
- ret = mv88e6xxx_phy_page_read(ds, 0, 6, 26);
- if (ret < 0)
- return ret;
- temp = clamp_val(DIV_ROUND_CLOSEST(temp, 5) + 5, 0, 0x1f);
- return mv88e6xxx_phy_page_write(ds, 0, 6, 26,
- (ret & 0xe0ff) | (temp << 8));
-}
-
-static int mv88e6352_get_temp_alarm(struct dsa_switch *ds, bool *alarm)
-{
- int ret;
-
- *alarm = false;
-
- ret = mv88e6xxx_phy_page_read(ds, 0, 6, 26);
- if (ret < 0)
- return ret;
-
- *alarm = !!(ret & 0x40);
-
- return 0;
-}
-#endif /* CONFIG_NET_DSA_HWMON */
-