-#. Update the Floating Network configuration.
-
- - Set the Floating IP range start (default 172.16.0.130)
-
- - Set the Floating IP range end (default 172.16.0.254)
-
- - Set the Floating network name (default admin_floating_net)
-
-#. Update the Internal Network configuration.
-
- - Set Internal network CIDR to an appropriate value (default 192.168.111.0/24)
-
- - Set Internal network gateway to an appropriate value
-
- - Set the Internal network name (default admin_internal_net)
-
-#. Update the Guest OS DNS servers.
-
- - Set Guest OS DNS Server values appropriately
-
-#. Save Settings.
-
-#. Select the "Other" Node Networks group on the left pane (see figure below).
-
- .. figure:: img/other.png
-
-#. Update the Public network assignment.
-
- - Check the box for "Assign public network to all nodes" (Required by OpenDaylight)
-
-#. Update Host OS DNS Servers.
-
- - Provide the DNS server settings
-
-#. Update Host OS NTP Servers.
-
- - Provide the NTP server settings
-
-Select Hypervisor type
-======================
-
-#. In the FUEL UI of your Environment, click the "Settings" Tab
-
-#. Select "Compute" on the left side pane (see figure below)
-
- - Check the KVM box and press "Save settings"
-
- .. figure:: img/compute.png
-
-Enable Plugins
-==============
-
-#. In the FUEL UI of your Environment, click the "Settings" Tab
-
-#. Select Other on the left side pane (see figure below)
-
- - Enable and configure the plugins of your choice
-
- .. figure:: img/plugins.png
-
-Allocate nodes to environment and assign functional roles
-=========================================================
-
-#. Click on the "Nodes" Tab in the FUEL WEB UI (see figure below).
-
- .. figure:: img/addnodes.png
-
-#. Assign roles (see figure below).
-
- - Click on the <+Add Nodes> button
-
- - Check <Controller>, <Telemetry - MongoDB> and optionally an SDN Controller role (OpenDaylight controller/ONOS) in the "Assign Roles" Section.
-
- - Check one node which you want to act as a Controller from the bottom half of the screen
-
- - Click <Apply Changes>.
-
- - Click on the <+Add Nodes> button
-
- - Check the <Controller> and <Storage - Ceph OSD> roles.
-
- - Check the two next nodes you want to act as Controllers from the bottom half of the screen
-
- - Click <Apply Changes>
-
- - Click on <+Add Nodes> button
-
- - Check the <Compute> and <Storage - Ceph OSD> roles.
-
- - Check the Nodes you want to act as Computes from the bottom half of the screen
-
- - Click <Apply Changes>.
-
- .. figure:: img/computelist.png
-
-#. Configure interfaces (see figure below).
-
- - Check Select <All> to select all allocated nodes
-
- - Click <Configure Interfaces>
-
- - Assign interfaces (bonded) for mgmt-, admin-, private-, public- and storage networks
-
- - Click <Apply>
-
- .. figure:: img/interfaceconf.png
-
-
-Target specific configuration
-=============================
-
-#. Set up targets for provisioning with non-default "Offloading Modes"
-
- Some target nodes may require additional configuration after they are
- PXE booted (bootstrapped); the most frequent changes are in defaults
- for ethernet devices' "Offloading Modes" settings (e.g. some targets'
- ethernet drivers may strip VLAN traffic by default).
-
- If your target ethernet drivers have wrong "Offloading Modes" defaults,
- in "Configure interfaces" page (described above), expand affected
- interface's "Offloading Modes" and [un]check the relevant settings
- (see figure below):
-
- .. figure:: img/offloadingmodes.png
-
-#. Set up targets for "Verify Networks" with non-default "Offloading Modes"
-
- **NOTE**: Check *Reference 15* for an updated and comprehensive list of
- known issues and/or limitations, including "Offloading Modes" not being
- applied during "Verify Networks" step.
-
- Setting custom "Offloading Modes" in Fuel GUI will only apply those settings
- during provisiong and **not** during "Verify Networks", so if your targets
- need this change, you have to apply "Offloading Modes" settings by hand
- to bootstrapped nodes.
-
- **E.g.**: Our driver has "rx-vlan-filter" default "on" (expected "off") on
- the Openstack interface(s) "eth1", preventing VLAN traffic from passing
- during "Verify Networks".
-
- - From Fuel master console identify target nodes admin IPs (see figure below):
-
- .. code-block:: bash
-
- $ fuel nodes
-
- .. figure:: img/fuelconsole1.png
-
- - SSH into each of the target nodes and disable "rx-vlan-filter" on the
- affected physical interface(s) allocated for OpenStack traffic (eth1):
-
- .. code-block:: bash
-
- $ ssh root@10.20.0.6 ethtool -K eth1 rx-vlan-filter off
-
- - Repeat the step above for all affected nodes/interfaces in the POD.
-
-Verify Networks
-===============
-
-It is important that the Verify Networks action is performed as it will verify
-that communicate works for the networks you have setup, as well as check that
-packages needed for a successful deployment can be fetched.
-
-#. From the FUEL UI in your Environment, Select the Networks Tab and select "Connectivity check" on the left pane (see figure below)
-
- - Select <Verify Networks>
-
- - Continue to fix your topology (physical switch, etc) until the "Verification Succeeded" and "Your network is configured correctly" message is shown
-
- .. figure:: img/verifynet.png
-
-Deploy Your Environment
-=======================
-
-#. Deploy the environment.
-
- - In the Fuel GUI, click on the "Dashboard" Tab.
-
- - Click on <Deploy Changes> in the "Ready to Deploy?" section
-
- - Examine any information notice that pops up and click <Deploy>
-
- Wait for your deployment to complete, you can view the "Dashboard"
- Tab to see the progress and status of your deployment.
-
-=========================
-Installation health-check
-=========================
-
-#. Perform system health-check (see figure below)
-
- - Click the "Health Check" tab inside your Environment in the FUEL Web UI
-
- - Check <Select All> and Click <Run Tests>
-
- - Allow tests to run and investigate results where appropriate
-
- .. figure:: img/health.png
Code Review / fuel.git / blobdiff