#CHARACTERIZE VSWITCH PERFORMANCE FOR TELCO NFV USE CASES LEVEL TEST DESIGN ##Table of Contents - [1. Introduction](#Introduction) - [1.1. Document identifier](#DocId) - [1.2. Scope](#Scope) - [1.3. References](#References) - [2. Details of the Level Test Design](#DetailsOfTheLevelTestDesign) - [2.1. Features to be tested](#FeaturesToBeTested) - [2.2. Approach](#Approach) - [2.3. Test identification](#TestIdentification) - [2.3.1 Throughput tests](#ThroughputTests) - [2.3.2 Packet Delay Tests](#PacketDelayTests) - [2.3.3 Scalability Tests](#ScalabilityTests) - [2.3.4 CPU and Memory Consumption Tests](#CPUTests) - [2.3.5 Coupling Between the Control Path and The Datapath Tests](#CPDPTests) - [2.3.6 Time to Establish Flows Tests](#FlowLatencyTests) - [2.3.7 Noisy Neighbour Tests](#NoisyNeighbourTests) - [2.3.8 Overlay Tests](#OverlayTests) - [2.3.9 Summary Test List](#SummaryList) - [2.4. Feature pass/fail criteria](#PassFail) - [2.5. Test deliverables](#TestDeliverables) - [3. General](#General) - [3.1. Glossary](#Glossary) - [3.2. Document change procedures and history](#History) - [3.3. Contributors](#Contributors)
--- ##1. Introduction The objective of the OPNFV project titled **“Characterize vSwitch Performance for Telco NFV Use Cases”**, is to evaluate a virtual switch to identify its suitability for a Telco Network Function Virtualization (NFV) environment. The intention of this Level Test Design (LTD) document is to specify the set of tests to carry out in order to objectively measure the current characteristics of a virtual switch in the Network Function Virtualization Infrastructure (NFVI) as well as the test pass criteria. The detailed test cases will be defined in [Section 2](#DetailsOfTheLevelTestDesign), preceded by the [Document identifier](#DocId) and the [Scope](#Scope). This document is currently in draft form. ###1.1. Document identifier The document id will be used to uniquely identify versions of the LTD. The format for the document id will be: OPNFV\_vswitchperf\_LTD\_ver\_NUM\_MONTH\_YEAR\_STATUS, where by the status is one of: draft, reviewed, corrected or final. The document id for this version of the LTD is: OPNFV\_vswitchperf\_LTD\_ver\_1.6\_Jan\_15\_DRAFT. ###1.2. Scope The main purpose of this project is to specify a suite of performance tests in order to objectively measure the current packet transfer characteristics of a virtual switch in the NFVI. The intent of the project is to facilitate testing of any virtual switch. Thus, a generic suite of tests shall be developed, with no hard dependencies to a single implementation. In addition, the test case suite shall be architecture independent. The test cases developed in this project shall not form part of a separate test framework, all of these tests may be inserted into the Continuous Integration Test Framework and/or the Platform Functionality Test Framework - if a vSwitch becomes a standard component of an OPNFV release. ###1.3. References - [RFC 1242 Benchmarking Terminology for Network Interconnection Devices](http://www.ietf.org/rfc/rfc1242.txt) - [RFC 2544 Benchmarking Methodology for Network Interconnect Devices](http://www.ietf.org/rfc/rfc2544.txt) - [RFC 2285 Benchmarking Terminology for LAN Switching Devices](http://www.ietf.org/rfc/rfc2285.txt) - [RFC 2889 Benchmarking Methodology for LAN Switching Devices](http://www.ietf.org/rfc/rfc2889.txt) - [RFC 3918 Methodology for IP Multicast Benchmarking](http://www.ietf.org/rfc/rfc3918.txt) - [RFC 4737 Packet Reordering Metrics](http://www.ietf.org/rfc/rfc4737.txt) - [RFC 5481 Packet Delay Variation Applicability Statement](http://www.ietf.org/rfc/rfc5481.txt) - [RFC 6201 Device Reset Characterization](http://tools.ietf.org/html/rfc6201)
##2. Details of the Level Test Design This section describes the features to be tested ([cf. 2.1](#FeaturesToBeTested)), the test approach ([cf. 2.2](#Approach)); it also identifies the sets of test cases or scenarios ([cf. 2.3](#TestIdentification)) along with the pass/fail criteria ([cf. 2.4](#PassFail)) and the test deliverables ([cf. 2.5](#TestDeliverables)). ###2.1. Features to be tested Characterizing virtual switches (i.e. Device Under Test (DUT) in this document) includes measuring the following performance metrics: - **Throughput** as defined by [RFC1242]: The maximum rate at which **none** of the offered frames are dropped by the DUT. The maximum frame rate and bit rate that can be transmitted by the DUT without any error should be recorded. Note there is an equivalent bit rate and a specific layer at which the payloads contribute to the bits. Errors and improperly formed frames or packets are dropped. - **Packet delay** introduced by the DUT and its cumulative effect on E2E networks. Frame delay can be measured equivalently. - **Packet delay variation**: measured from the perspective of the VNF/application. Packet delay variation is sometimes called "jitter". However, we will avoid the term "jitter" as the term holds different meaning to different groups of people. In this document we will simply use the term packet delay variation. The preferred form for this metric is the PDV form of delay variation defined in [RFC5481]. - **Packet loss** (within a configured waiting time at the receiver): All packets sent to the DUT should be accounted for. - **Burst behaviour**: measures the ability of the DUT to buffer packets. - **Packet re-ordering**: measures the ability of the device under test to maintain sending order throughout transfer to the destination. - **Packet correctness**: packets or Frames must be well-formed, in that they include all required fields, conform to length requirements, pass integrity checks, etc. - **Availability and capacity** of the DUT i.e. when the DUT is fully “up” and connected: - Includes power consumption of the CPU (in various power states) and system. - Includes CPU utilization. - Includes the number of NIC interfaces supported. - Includes headroom of VM workload processing cores (i.e. available for applications). ###2.2. Approach In order to determine the packet transfer characteristics of a virtual switch, the tests will be broken down into the following categories: - **Throughput Tests** to measure the maximum forwarding rate (in frames per second or fps) and bit rate (in Mbps) for a constant load (as defined by [RFC1242]) without traffic loss. - **Packet and Frame Delay Tests** to measure average, min and max packet and frame delay for constant loads. - **Stream Performance Tests** (TCP, UDP) to measure bulk data transfer performance, i.e. how fast systems can send and receive data through the switch. - **Request/Response Performance** Tests (TCP, UDP) the measure the transaction rate through the switch. - **Packet Delay Tests** to understand latency distribution for different packet sizes and over an extended test run to uncover outliers. - **Scalability Tests** to understand how the virtual switch performs as the number of flows, active ports, complexity of the forwarding logic's configuration... it has to deal with increases. - **Control Path and Datapath Coupling** Tests, to understand how closely coupled the datapath and the control path are as well as the effect of this coupling on the performance of the DUT. - **CPU and Memory Consumption Tests** to understand the virtual switch’s footprint on the system, this includes: - CPU utilization - Cache utilization - Memory footprint - Time To Establish Flows Tests. - **Noisy Neighbour Tests**, to understand the effects of resource sharing on the performance of a virtual switch. **Note:** some of the tests above can be conducted simultaneously where the combined results would be insightful, for example Packet/Frame Delay and Scalability. The following represents possible deployments which can help to determine the performance of both the virtual switch and the datapath into the VNF: - Physical port → virtual switch → physical port.

                                                         __
    +--------------------------------------------------+   |
    |              +--------------------+              |   |
    |              |                    |              |   |
    |              |                    v              |   |  Host
    |   +--------------+            +--------------+   |   |
    |   |   phy port   |  vSwitch   |   phy port   |   |   |
    +---+--------------+------------+--------------+---+ __|
               ^                           :
               |                           |
               :                           v
    +--------------------------------------------------+
    |                                                  |
    |                traffic generator                 |
    |                                                  |
    +--------------------------------------------------+
- Physical port → virtual switch → VNF → virtual switch → physical port.

                                                          __
    +---------------------------------------------------+   |
    |                                                   |   |
    |   +-------------------------------------------+   |   |
    |   |                 Application               |   |   |
    |   +-------------------------------------------+   |   |
    |       ^                                  :        |   |
    |       |                                  |        |   |  Guest
    |       :                                  v        |   |
    |   +---------------+           +---------------+   |   |
    |   | logical port 0|           | logical port 1|   |   |
    +---+---------------+-----------+---------------+---+ __|
            ^                                  :
            |                                  |
            :                                  v         __
    +---+---------------+----------+---------------+---+   |
    |   | logical port 0|          | logical port 1|   |   |
    |   +---------------+          +---------------+   |   |
    |       ^                                  :       |   |
    |       |                                  |       |   |  Host
    |       :                                  v       |   |
    |   +--------------+            +--------------+   |   |
    |   |   phy port   |  vSwitch   |   phy port   |   |   |
    +---+--------------+------------+--------------+---+ __|
               ^                           :
               |                           |
               :                           v
    +--------------------------------------------------+
    |                                                  |
    |                traffic generator                 |
    |                                                  |
    +--------------------------------------------------+
- Physical port → virtual switch → VNF → virtual switch → VNF → virtual switch → physical port.


                                                   __
 +----------------------+  +----------------------+  |
 |   Guest 1            |  |   Guest 2            |  |
 |   +---------------+  |  |   +---------------+  |  |
 |   |  Application  |  |  |   |  Application  |  |  |
 |   +---------------+  |  |   +---------------+  |  |
 |       ^       |      |  |       ^       |      |  |
 |       |       v      |  |       |       v      |  |  Guests
 |   +---------------+  |  |   +---------------+  |  |
 |   | logical ports |  |  |   | logical ports |  |  |
 |   |   0       1   |  |  |   |   0       1   |  |  |
 +---+---------------+--+  +---+---------------+--+__|
         ^       :                 ^       :
         |       |                 |       |
         :       v                 :       v       _
 +---+---------------+---------+---------------+--+ |
 |   |   0       1   |         |   3       4   |  | |
 |   | logical ports |         | logical ports |  | |
 |   +---------------+         +---------------+  | |
 |       ^       |                 ^       |      | |  Host
 |       |       L-----------------+       v      | |
 |   +--------------+          +--------------+   | |
 |   |   phy ports  | vSwitch  |   phy ports  |   | |
 +---+--------------+----------+--------------+---+_|
         ^       :                 ^       :
         |       |                 |       |
         :       v                 :       v
 +--------------------------------------------------+
 |                                                  |
 |                traffic generator                 |
 |                                                  |
 +--------------------------------------------------+

- Physical port → virtual switch → VNF.

                                                          __
    +---------------------------------------------------+   |
    |                                                   |   |
    |   +-------------------------------------------+   |   |
    |   |                 Application               |   |   |
    |   +-------------------------------------------+   |   |
    |       ^                                           |   |
    |       |                                           |   |  Guest
    |       :                                           |   |
    |   +---------------+                               |   |
    |   | logical port 0|                               |   |
    +---+---------------+-------------------------------+ __|
            ^
            |
            :                                            __
    +---+---------------+------------------------------+   |
    |   | logical port 0|                              |   |
    |   +---------------+                              |   |
    |       ^                                          |   |
    |       |                                          |   |  Host
    |       :                                          |   |
    |   +--------------+                               |   |
    |   |   phy port   |  vSwitch                      |   |
    +---+--------------+------------ -------------- ---+ __|
               ^
               |
               :
    +--------------------------------------------------+
    |                                                  |
    |                traffic generator                 |
    |                                                  |
    +--------------------------------------------------+
- VNF → virtual switch → physical port.

                                                          __
    +---------------------------------------------------+   |
    |                                                   |   |
    |   +-------------------------------------------+   |   |
    |   |                 Application               |   |   |
    |   +-------------------------------------------+   |   |
    |                                          :        |   |
    |                                          |        |   |  Guest
    |                                          v        |   |
    |                               +---------------+   |   |
    |                               | logical port  |   |   |
    +-------------------------------+---------------+---+ __|
                                               :
                                               |
                                               v         __
    +------------------------------+---------------+---+   |
    |                              | logical port  |   |   |
    |                              +---------------+   |   |
    |                                          :       |   |
    |                                          |       |   |  Host
    |                                          v       |   |
    |                               +--------------+   |   |
    |                     vSwitch   |   phy port   |   |   |
    +-------------------------------+--------------+---+ __|
                                           :
                                           |
                                           v
    +--------------------------------------------------+
    |                                                  |
    |                traffic generator                 |
    |                                                  |
    +--------------------------------------------------+
- virtual switch → VNF → virtual switch.

                                                                                                                 __
    +---------------------------------------------------+   +---------------------------------------------------+  |
    |   Guest 1                                         |   |   Guest 2                                         |  |
    |   +-------------------------------------------+   |   |   +-------------------------------------------+   |  |
    |   |                 Application               |   |   |   |                 Application               |   |  |
    |   +-------------------------------------------+   |   |   +-------------------------------------------+   |  |
    |                                          :        |   |       ^                                           |  |
    |                                          |        |   |       |                                           |  |  Guest
    |                                          v        |   |       :                                           |  |
    |                               +---------------+   |   |   +---------------+                               |  |
    |                               | logical port 0|   |   |   | logical port 0|                               |  |
    +-------------------------------+---------------+---+   +---+---------------+-------------------------------+__|
                                               :                    ^
                                               |                    |
                                               v                    :                                            __
    +------------------------------+---------------+------------+---------------+-------------------------------+  |
    |                              |     port 0    |            |     port 1    |                               |  |
    |                              +---------------+            +---------------+                               |  |
    |                                          :                    ^                                           |  |
    |                                          |                    |                                           |  |  Host
    |                                          +--------------------+                                           |  |
    |                                                                                                           |  |
    |                                                  vswitch                                                  |  |
    +-----------------------------------------------------------------------------------------------------------+__|
**Note:** For tests where the traffic generator and/or measurement receiver are implemented on VM and connected to the virtual switch through vNIC, the issues of shared resources and interactions between the measurement devices and the device under test must be considered. ####General Methodology: To establish the baseline performance of the virtual switch, tests would initially be run with a simple workload in the VNF (the recommended simple workload VNF would be [DPDK]'s testpmd application forwarding packets in a VM or vloop_vnf a simple kernel module that forwards traffic between two network interfaces inside the virtualized environment while bypassing the networking stack). Subsequently, the tests would also be executed with a real Telco workload running in the VNF, which would exercise the virtual switch in the context of higher level Telco NFV use cases, and prove that its underlying characteristics and behaviour can be measured and validated. Suitable real Telco workload VNFs are yet to be identified. #####Default Test Parameters: The following list identifies the default parameters for suite of tests: - Reference application: Simple forwarding or Open Source VNF. - Frame size (bytes): 64, 128, 256, 512, 1024, 1280, 1518, 2K, 4k OR Packet size based on use-case (e.g. RTP 64B, 256B). - Reordering check: Tests should confirm that packets within a flow are not reordered. - Duplex: Unidirectional / Bidirectional. Default: Full duplex with traffic transmitting in both directions, as network traffic generally does not flow in a single direction. By default the data rate of transmitted traffic should be the same in both directions, please note that asymmetric traffic (e.g. downlink-heavy) tests will be mentioned explicitly for the relevant test cases. - Number of Flows: Default for non scalability tests is a single flow. For scalability tests the goal is to test with maximum supported flows but where possible will test up to 10 Million flows. Start with a single flow and scale up. By default flows should be added sequentially, tests that add flows simultaneously will explicitly call out their flow addition behaviour. Packets are generated across the flows uniformly with no burstiness. - Traffic Types: UDP, SCTP, RTP, GTP and UDP traffic. - Deployment scenarios are: - Physical → virtual switch → physical. - Physical → virtual switch → VNF → virtual switch → physical. - Physical → virtual switch → VNF → virtual switch → VNF → virtual switch → physical. - Physical → virtual switch → VNF. - VNF → virtual switch → Physical. - VNF → virtual switch → VNF. Tests MUST have these parameters unless otherwise stated. **Test cases with non default parameters will be stated explicitly**. **Note**: For throughput tests unless stated otherwise, test configurations should ensure that traffic traverses the installed flows through the switch, i.e. flows are installed and have an appropriate time out that doesn't expire before packet transmission starts. #####Test Priority Tests will be assigned a priority in order to determine which tests should be implemented immediately and which tests implementations can be deferred. Priority can be of following types: - Urgent: Must be implemented immediately. - High: Must be implemented in the next release. - Medium: May be implemented after the release. - Low: May or may not be implemented at all. #####DUT Setup The DUT should be configured to its "default" state. The DUT's configuration or set-up must not change between tests in any way other than what is required to do the test. All supported protocols must be configured and enabled for each test set up. #####Port Configuration The DUT should be configured with n ports where n is a multiple of 2. Half of the ports on the DUT should be used as ingress ports and the other half of the ports on the DUT should be used as egress ports. Where a DUT has more than 2 ports, the ingress data streams should be set-up so that they transmit packets to the egress ports in sequence so that there is an even distribution of traffic across ports. For example, if a DUT has 4 ports 0(ingress), 1(ingress), 2(egress) and 3(egress), the traffic stream directed at port 0 should output a packet to port 2 followed by a packet to port 3. The traffic stream directed at port 1 should also output a packet to port 2 followed by a packet to port 3. #####Frame formats Layer 2 (data link layer) protocols: - Ethernet II


  +-----------------------------+-----------------------------------------------------------------------+---------+
  |       Ethernet Header       |                                Payload                                |Check Sum|
  +-----------------------------+-----------------------------------------------------------------------+---------+
   |___________________________| |_____________________________________________________________________| |_______|
              14 Bytes                                       46 - 1500 Bytes                              4 Bytes

  
Layer 3 (network layer) protocols: - IPv4


  +-----------------------------+-------------------------------------+---------------------------------+---------+
  |       Ethernet Header       |              IP Header              |             Payload             |Check Sum|
  +-----------------------------+-------------------------------------+---------------------------------+---------+
   |___________________________| |___________________________________| |_______________________________| |_______|
              14 Bytes                         20 Bytes                         26 - 1480 Bytes           4 Bytes

  
- IPv6


  +-----------------------------+-------------------------------------+---------------------------------+---------+
  |       Ethernet Header       |              IP Header              |             Payload             |Check Sum|
  +-----------------------------+-------------------------------------+---------------------------------+---------+
   |___________________________| |___________________________________| |_______________________________| |_______|
              14 Bytes                         40 Bytes                         26 - 1460 Bytes           4 Bytes

  
Layer 4 (transport layer) protocols: - TCP - UDP - SCTP


  +-----------------------------+-------------------------------------+-----------------+---------------+---------+
  |       Ethernet Header       |              IP Header              | Layer 4 Header  |    Payload    |Check Sum|
  +-----------------------------+-------------------------------------+-----------------+---------------+---------+
   |___________________________| |___________________________________| |_______________| |_____________| |_______|
              14 Bytes                         20 Bytes                    20 Bytes       6 - 1460 Bytes  4 Bytes

  
Layer 5 (application layer) protocols: - RTP - GTP


  +-----------------------------+-------------------------------------+-----------------+---------------+---------+
  |       Ethernet Header       |              IP Header              | Layer 4 Header  |    Payload    |Check Sum|
  +-----------------------------+-------------------------------------+-----------------+---------------+---------+
   |___________________________| |___________________________________| |_______________| |_____________| |_______|
              14 Bytes                         20 Bytes                    20 Bytes        Min 6 Bytes    4 Bytes

  
#####Packet Throughput There is a difference between an Ethernet frame, an IP packet, and a UDP datagram. In the seven-layer OSI model of computer networking, packet refers to a data unit at layer 3 (network layer). The correct term for a data unit at layer 2 (data link layer) is a frame, and at layer 4 (transport layer) is a segment or datagram. Important concepts related to 10GbE performance are frame rate and throughput. The MAC bit rate of 10GbE, defined in the IEEE standard 802 .3ae, is 10 billion bits per second. Frame rate is based on the bit rate and frame format definitions. Throughput, defined in IETF RFC 1242, is the highest rate at which the system under test can forward the offered load, without loss. The frame rate for 10GbE is determined by a formula that divides the 10 billion bits per second by the preamble + frame length + inter-frame gap. The maximum frame rate is calculated using the minimum values of the following parameters, as described in the IEEE 802 .3ae standard: - Preamble: 8 bytes * 8 = 64 bits - Frame Length: 64 bytes (minimum) * 8 = 512 bits - Inter-frame Gap: 12 bytes (minimum) * 8 = 96 bits Therefore, Maximum Frame Rate (64B Frames) = MAC Transmit Bit Rate / (Preamble + Frame Length + Inter-frame Gap) = 10,000,000,000 / (64 + 512 + 96) = 10,000,000,000 / 672 = 14,880,952.38 frame per second (fps) #####RFC 1242 Benchmarking Terminology for Network Interconnection Devices RFC 1242 defines the terminology that is used in describing performance benchmarking tests and their results. Definitions and discussions covered include: Back-to-back, bridge, bridge/router, constant load, data link frame size, frame loss rate, inter frame gap, latency, and many more. #####RFC 2544 Benchmarking Methodology for Network Interconnect Devices RFC 2544 outlines a benchmarking methodology for network Interconnect Devices. The methodology results in performance metrics such as latency, frame loss percentage, and maximum data throughput. In this document network “throughput” (measured in millions of frames per second) is based on RFC 2544, unless otherwise noted. Frame size refers to Ethernet frames ranging from smallest frames of 64 bytes to largest frames of 4K bytes. Types of tests are: 1. Throughput test defines the maximum number of frames per second that can be transmitted without any error. 2. Latency test measures the time required for a frame to travel from the originating device through the network to the destination device. Please note that note RFC2544 Latency measurement will be superseded with a measurement of average latency over all successfully transferred packets or frames. 3. Frame loss test measures the network’s response in overload conditions - a critical indicator of the network’s ability to support real-time applications in which a large amount of frame loss will rapidly degrade service quality. 4. Burst test assesses the buffering capability of a switch. It measures the maximum number of frames received at full line rate before a frame is lost. In carrier Ethernet networks, this measurement validates the excess information rate (EIR) as defined in many SLAs. 5. System recovery to characterize speed of recovery from an overload condition 6. Reset to characterize speed of recovery from device or software reset. This type of test has been updated by [RFC6201] as such, the methodology defined by this specification will be that of RFC 6201. Although not included in the defined RFC 2544 standard, another crucial measurement in Ethernet networking is packet delay variation. The definition set out by this specification comes from [RFC5481]. #####RFC 2285 Benchmarking Terminology for LAN Switching Devices RFC 2285 defines the terminology that is used to describe the terminology for benchmarking a LAN switching device. It extends RFC 1242 and defines: DUTs, SUTs, Traffic orientation and distribution, bursts, loads, forwarding rates, etc. #####RFC 2889 Benchmarking Methodology for LAN Switching RFC 2889 outlines a benchmarking methodology for LAN switching, it extends RFC 2544. The outlined methodology gathers performance metrics for forwarding, congestion control, latency, address handling and finally filtering. #####RFC 3918 Methodology for IP Multicast Benchmarking RFC 3918 outlines a methodology for IP Multicast benchmarking. #####RFC 4737 Packet Reordering Metrics RFC 4737 describes metrics for identifying and counting re-ordered packets within a stream, and metrics to measure the extent each packet has been re-ordered. #####RFC 5481 Packet Delay Variation Applicability Statement RFC 5481 defined two common, but different forms of delay variation metrics, and compares the metrics over a range of networking circumstances and tasks. The most suitable form for vSwitch benchmarking is the "PDV" form. #####RFC 6201 Device Reset Characterization RFC 6201 extends the methodology for characterizing the speed of recovery of the DUT from device or software reset described in RFC 2544. ###2.3. Test identification ####2.3.1 Throughput tests The following tests aim to determine the maximum forwarding rate that can be achieved with a virtual switch. The following list is not exhaustive but should indicate the type of tests that should be required. It is expected that more will be added. - #####Test ID: LTD.Throughput.RFC2544.PacketLossRatio **Title**: RFC 2544 X% packet loss ratio Throughput and Latency Test **Prerequisite Test**: N/A **Priority**: **Description**: This test determines the DUT's maximum forwarding rate with X% traffic loss for a constant load (fixed length frames at a fixed interval time). The default loss percentages to be tested are: - X = 0% - X = 10^-7% Note: Other values can be tested if required by the user. The selected frame sizes are those previously defined under [Default Test Parameters](#DefaultParams). The test can also be used to determine the average latency of the traffic. Under the [RFC2544] test methodology, the test duration will include a number of trials; each trial should run for a minimum period of 60 seconds. A binary search methodology must be applied for each trial to obtain the final result. **Expected Result**: At the end of each trial, the presence or absence of loss determines the modification of offered load for the next trial, converging on a maximum rate, or [RFC2544] Throughput with X% loss. The Throughput load is re-used in related [RFC2544] tests and other tests. **Metrics Collected**: The following are the metrics collected for this test: - The maximum forwarding rate in Frames Per Second (FPS) and Mbps of the DUT for each frame size with X% packet loss. - The average latency of the traffic flow when passing through the DUT (if testing for latency, note that this average is different from the test specified in Section 26.3 of [RFC2544]). - CPU and memory utilization may also be collected as part of this test, to determine the vSwitch's performance footprint on the system.
- #####Test ID: LTD.Throughput.RFC2544.PacketLossRatioFrameModification **Title**: RFC 2544 X% packet loss Throughput and Latency Test with packet modification **Prerequisite Test**: N\A **Priority**: **Description**: This test determines the DUT's maximum forwarding rate with X% traffic loss for a constant load (fixed length frames at a fixed interval time). The default loss percentages to be tested are: - X = 0% - X = 10^-7% Note: Other values can be tested if required by the user. The selected frame sizes are those previously defined under [Default Test Parameters](#DefaultParams). The test can also be used to determine the average latency of the traffic. Under the [RFC2544] test methodology, the test duration will include a number of trials; each trial should run for a minimum period of 60 seconds. A binary search methodology must be applied for each trial to obtain the final result. During this test, the DUT must perform the following operations on the traffic flow: - Perform packet parsing on the DUT's ingress port. - Perform any relevant address look-ups on the DUT's ingress ports. - Modify the packet header before forwarding the packet to the DUT's egress port. Packet modifications include: - Modifying the Ethernet source or destination MAC address. - Modifying/adding a VLAN tag. - Modifying/adding a MPLS tag. - Modifying the source or destination ip address. - Modifying the TOS/DSCP field. - Modifying the source or destination ports for UDP/TCP/SCTP (Recommended). - Modifying the TTL. **Expected Result**: The Packet parsing/modifications require some additional degree of processing resource, therefore the [RFC2544] Throughput is expected to be somewhat lower than the Throughput level measured without additional steps. The reduction is expected to be greatest on tests with the smallest packet sizes (greatest header processing rates). **Metrics Collected**: The following are the metrics collected for this test: - The maximum forwarding rate in Frames Per Second (FPS) and Mbps of the DUT for each frame size with X% packet loss and packet modification operations being performed by the DUT. - The average latency of the traffic flow when passing through the DUT (if testing for latency, note that this average is different from the test specified in Section 26.3 of [RFC2544]). - The [RFC5481] PDV form of delay variation on the traffic flow, using the 99th percentile. - CPU and memory utilization may also be collected as part of this test, to determine the vSwitch's performance footprint on the system.
- #####Test ID: LTD.Throughput.RFC2544.SystemRecoveryTime **Title**: RFC 2544 System Recovery Time Test **Prerequisite Test** LTD.Throughput.RFC2544.PacketLossRatio **Priority**: **Description**: The aim of this test is to determine the length of time it takes the DUT to recover from an overload condition for a constant load (fixed length frames at a fixed interval time). The selected frame sizes are those previously defined under [Default Test Parameters](#DefaultParams), traffic should be sent to the DUT under normal conditions. During the duration of the test and while the traffic flows are passing though the DUT, at least one situation leading to an overload condition for the DUT should occur. The time from the end of the overload condition to when the DUT returns to normal operations should be measured to determine recovery time. Prior to overloading the DUT, one should record the average latency for 10,000 packets forwarded through the DUT. The overload condition SHOULD be to transmit traffic at a very high frame rate to the DUT (150% of the maximum 0% packet loss rate as determined by LTD.Throughput.RFC2544.PacketLossRatio or line-rate whichever is lower), for at least 60 seconds, then reduce the frame rate to 75% of the maximum 0% packet loss rate. A number of time-stamps should be recorded: - Record the time-stamp at which the frame rate was reduced and record a second time-stamp at the time of the last frame lost. The recovery time is the difference between the two timestamps. - Record the average latency for 10,000 frames after the last frame loss and continue to record average latency measurements for every 10,000 frames, when latency returns to within 10% of pre-overload levels record the time-stamp. **Expected Result**: **Metrics collected** The following are the metrics collected for this test: - The length of time it takes the DUT to recover from an overload condition. - The length of time it takes the DUT to recover the average latency to pre-overload conditions. **Deployment scenario**: - Physical → virtual switch → physical.
- #####Test ID: LTD.Throughput.RFC2544.BackToBackFrames **Title**: RFC 2544 Back To Back Frames Test **Prerequisite Test**: N\A **Priority**: **Description**: The aim of this test is to characterize the ability of the DUT to process back-to-back frames. For each frame size previously defined under [Default Test Parameters](#DefaultParams), a burst of traffic is sent to the DUT with the minimum inter-frame gap between each frame. If the number of received frames equals the number of frames that were transmitted, the burst size should be increased and traffic is sent to the DUT again. The value measured is the back-to-back value, that is the maximum burst size the DUT can handle without any frame loss. **Expected Result**: Tests of back-to-back frames with physical devices have produced unstable results in some cases. All tests should be repeated in multiple test sessions and results stability should be examined. **Metrics collected** The following are the metrics collected for this test: - The back-to-back value, which is the the number of frames in the longest burst that the DUT will handle without the loss of any frames. - CPU and memory utilization may also be collected as part of this test, to determine the vSwitch's performance footprint on the system. **Deployment scenario**: - Physical → virtual switch → physical.
- #####Test ID: LTD.Throughput.RFC2544.Soak **Title**: RFC 2544 X% packet loss Throughput Soak Test **Prerequisite Test** LTD.Throughput.RFC2544.PacketLossRatio **Priority**: **Description**: The aim of this test is to understand the Throughput stability over an extended test duration in order to uncover any outliers. To allow for an extended test duration, the test should ideally run for 24 hours or, if this is not possible, for at least 6 hour. For this test, each frame size must be sent at the highest Throughput with X% packet loss, as determined in the prerequisite test. The default loss percentages to be tested are: - X = 0% - X = 10^-7% Note: Other values can be tested if required by the user. **Expected Result**: **Metrics Collected**: The following are the metrics collected for this test: - Throughput stability of the DUT. - Any outliers in the Throughput stability. - Any unexpected variation in Throughput stability. - CPU and memory utilization may also be collected as part of this test, to determine the vSwitch's performance footprint on the system. - The [RFC5481] PDV form of delay variation on the traffic flow, using the 99th percentile.
- #####Test ID: LTD.Throughput.RFC2544.SoakFrameModification **Title**: RFC 2544 X% packet loss Throughput Soak Test with Frame Modification **Prerequisite Test** LTD.Throughput.RFC2544.PacketLossRatioFrameModification **Priority**: **Description**: The aim of this test is to understand the Throughput stability over an extended test duration in order to uncover any outliers. To allow for an extended test duration, the test should ideally run for 24 hours or, if this is not possible, for at least 6 hour. For this test, each frame size must be sent at the highest Throughput with X% packet loss, as determined in the prerequisite test. The default loss percentages to be tested are: - X = 0% - X = 10^-7% Note: Other values can be tested if required by the user. During this test, the DUT must perform the following operations on the traffic flow: - Perform packet parsing on the DUT's ingress port. - Perform any relevant address look-ups on the DUT's ingress ports. - Modify the packet header before forwarding the packet to the DUT's egress port. Packet modifications include: - Modifying the Ethernet source or destination MAC address. - Modifying/adding a VLAN tag. - Modifying/adding a MPLS tag. - Modifying the source or destination ip address. - Modifying the TOS/DSCP field. - Modifying the source or destination ports for UDP/TCP/SCTP (Recommended). - Modifying the TTL. **Expected Result**: **Metrics Collected**: The following are the metrics collected for this test: - Throughput stability of the DUT. - Any outliers in the Throughput stability. - Any unexpected variation in Throughput stability. - CPU and memory utilization may also be collected as part of this test, to determine the vSwitch's performance footprint on the system. - The [RFC5481] PDV form of delay variation on the traffic flow, using the 99th percentile.
- #####Test ID: LTD.Throughput.RFC6201.ResetTime **Title**: RFC 6201 Reset Time Test **Prerequisite Test**: N\A **Priority**: **Description**: The aim of this test is to determine the length of time it takes the DUT to recover from a reset. For each frame size previously defined under [Default Test Parameters](#DefaultParams), traffic should be sent to the DUT under normal conditions. During the duration of the test and while the traffic flows are passing through the DUT, the DUT should be reset and the Reset time measured. The Reset time is the total time that a device is determined to be out of operation and includes the time to perform the reset and the time to recover from it (cf. [RFC6201]) [RFC6201] defines two methods to measure the Reset time: - Frame-Loss Method: which requires the monitoring of the number of lost frames and calculates the Reset time based on the number of frames lost and the offered rate according to the following formula:

                              Frames_lost (packets)
          Reset_time = -------------------------------------
                         Offered_rate (packets per second)
  
- Timestamp Method: which measures the time from which the last frame is forwarded from the DUT to the time the first frame is forwarded after the reset. This involves time-stamping all transmitted frames and recording the timestamp of the last frame that was received prior to the reset and also measuring the timestamp of the first frame that is received after the reset. The Reset time is the difference between these two timestamps. According to [RFC6201] the choice of method depends on the test tool's capability; the Frame-Loss method SHOULD be used if the test tool supports: - Counting the number of lost frames per stream. - Transmitting test frame despite the physical link status. whereas the Timestamp method SHOULD be used if the test tool supports: - Timestamping each frame. - Monitoring received frame's timestamp. - Transmitting frames only if the physical link status is up. **Expected Result**: **Metrics collected** The following are the metrics collected for this test: - Average Reset Time. Results of this test should include the following information: - Throughput in Fps and Mbps. - Average Frame Loss. - Average Reset Time in milliseconds. - Number of trials. - Protocol: IPv4, IPv6, MPLS, etc. - Frame Size in Octets - Port Media: Ethernet, Gigabit Ethernet (GbE), etc. - Port Speed: 10 Gbps, 40 Gbps etc. - Interface Encapsulation: Ethernet, Ethernet VLAN, etc. **Deployment scenario**: - Physical → virtual switch → physical.
- #####Test ID: LTD.Throughput.RFC2889.ForwardingRate **Title**: RFC2889 Forwarding Rate Test **Prerequisite Test**: LTD.Throughput.RFC2544.PacketLossRatio **Priority**: **Description**: This test measures the DUT's Max Forwarding Rate when the Offered Load is varied between the throughput and the Maximum Offered Load for fixed length frames at a fixed time interval. The selected frame sizes are those previously defined under [Default Test Parameters](#DefaultParams). The throughput is the maximum offered load with 0% frame loss (measured by the prerequisite test), and the Maximum Offered Load (as defined by [RFC2885]) is _"the highest number of frames per second that an external source can transmit to a DUT/SUT for forwarding to a specified output interface or interfaces"_. Traffic should be sent to the DUT at a particular rate (TX rate) starting with TX rate equal to the throughput rate. The rate of successfully received frames at the destination counted (in FPS). If the RX rate is equal to the TX rate, the TX rate should be increased by a fixed step size and the RX rate measured again until the Max Forwarding Rate is found. The trial duration for each iteration should last for the period of time needed for the system to reach steady state for the frame size being tested. Under [RFC2889] test methodology, the test duration should run for a minimum period of 30 seconds, regardless whether the system reaches steady state before the minimum duration ends. **Expected Result**: According to [RFC2889] The Max Forwarding Rate is the highest forwarding rate of a DUT taken from an iterative set of forwarding rate measurements. The iterative set of forwarding rate measurements are made by setting the intended load transmitted from an external source and measuring the offered load (i.e what the DUT is capable of forwarding). If the Throughput == the Maximum Offered Load, it follows that Max Forwarding Rate is equal to the Maximum Offered Load. **Metrics Collected**: The following are the metrics collected for this test: - The Max Forwarding Rate for the DUT for each packet size. - CPU and memory utilization may also be collected as part of this test, to determine the vSwitch's performance footprint on the system.
- #####Test ID: LTD.Throughput.RFC2889.ForwardPressure **Title**: RFC2889 Forward Pressure Test **Prerequisite Test**: LTD.Throughput.RFC2889.ForwardingRate **Priority**: **Description**: The aim of this test is to determine if the DUT transmits frames with an inter-frame gap that is less than 12 bytes. This test overloads the DUT and measures the output for forward pressure. Traffic should be transmitted to the DUT with an inter-frame gap of 11 bytes, this will overload the DUT by 1 byte per frame. The forwarding rate of the DUT should be measured. **Expected Result**: The forwarding rate should not exceed the maximum forwarding rate of the DUT collected by LTD.Throughput.RFC2889.ForwardingRate. **Metrics collected** The following are the metrics collected for this test: - Forwarding rate of the DUT in FPS or Mbps. - CPU and memory utilization may also be collected as part of this test, to determine the vSwitch's performance footprint on the system. **Deployment scenario**: - Physical → virtual switch → physical.
- #####Test ID: LTD.Throughput.RFC2889.AddressCachingCapacity **Title**: RFC2889 Address Caching Capacity Test **Prerequisite Test**: N\A **Priority**: **Description**: The aim of this test is to determine the address caching capacity of the DUT for a constant load (fixed length frames at a fixed interval time). The selected frame sizes are those previously defined under [Default Test Parameters](#DefaultParams). In order to run this test the aging time, that is the maximum time the DUT will keep a learned address in its flow table, and a set of initial addresses, whose value should be >= 1 and <= the max number supported by the implementation must be known. Please note that if the aging time is configurable it must be longer than the time necessary to produce frames from the external source at the specified rate. If the aging time is fixed the frame rate must be brought down to a value that the external source can produce in a time that is less than the aging time. Learning Frames should be sent from an external source to the DUT to install a number of flows. The Learning Frames must have a fixed destination address and must vary the source address of the frames. The DUT should install flows in its flow table based on the varying source addresses. Frames should then be transmitted from an external source at a suitable frame rate to see if the DUT has properly learned all of the addresses. If there is no frame loss and no flooding, the number of addresses sent to the DUT should be increased and the test is repeated until the max number of cached addresses supported by the DUT determined. **Expected Result**: **Metrics collected**: The following are the metrics collected for this test: - Number of cached addresses supported by the DUT. - CPU and memory utilization may also be collected as part of this test, to determine the vSwitch's performance footprint on the system. **Deployment scenario**: - Physical → virtual switch → physical.
- #####Test ID: LTD.Throughput.RFC2889.AddressLearningRate **Title**: RFC2889 Address Learning Rate Test **Prerequisite Test**: LTD.Memory.RFC2889.AddressCachingCapacity **Priority**: **Description**: The aim of this test is to determine the rate of address learning of the DUT for a constant load (fixed length frames at a fixed interval time). The selected frame sizes are those previously defined under [Default Test Parameters](#DefaultParams), traffic should be sent with each IPv4/IPv6 address incremented by one. The rate at which the DUT learns a new address should be measured. The maximum caching capacity from LTD.Memory.RFC2889.AddressCachingCapacity should be taken into consideration as the maximum number of addresses for which the learning rate can be obtained. **Expected Result**: It may be worthwhile to report the behaviour when operating beyond address capacity - some DUTS may be more friendly to new addresses than others. **Metrics collected**: The following are the metrics collected for this test: - The address learning rate of the DUT. **Deployment scenario**: - Physical → virtual switch → physical.
- #####Test ID: LTD.Throughput.RFC2889.ErrorFramesFiltering **Title**: RFC2889 Error Frames Filtering Test **Prerequisite Test**: N\A **Priority**: **Description**: The aim of this test is to determine whether the DUT will propagate any erroneous frames it receives or whether it is capable of filtering out the erroneous frames. Traffic should be sent with erroneous frames included within the flow at random intervals. Illegal frames that must be tested include: - Undersize Frames. - Oversize Frames. - CRC error frames. - Fragment Frames. The traffic flow exiting the DUT should be recorded and checked to determine if the erroneous frames where passed through the DUT. **Expected Result**: Broken frames are not passed! **Metrics collected** No Metrics are collected in this test, instead it determines: - Whether the DUT will propagate erroneous frames. - Or whether the DUT will correctly filter out any erroneous frames from traffic flow with out removing correct frames. **Deployment scenario**: - Physical → virtual switch → physical.
- #####Test ID: LTD.Throughput.RFC2889.BroadcastFrameForwarding **Title**: RFC2889 Broadcast Frame Forwarding Test **Prerequisite Test**: N\A **Priority**: **Description**: The aim of this test is to determine the maximum forwarding rate of the DUT when forwarding broadcast traffic. For each frame previously defined under [Default Test Parameters](#DefaultParams), the traffic should be set up as broadcast traffic. The traffic throughput of the DUT should be measured. **Expected Result**: **Metrics collected** The following are the metrics collected for this test: - The forwarding rate of the DUT when forwarding broadcast traffic.
---- ####2.3.2 Packet Latency tests These tests will measure the store and forward latency as well as the packet delay variation for various packet types through the virtual switch. The following list is not exhaustive but should indicate the type of tests that should be required. It is expected that more will be added. - #####Test ID: LTD.PacketLatency.InitialPacketProcessingLatency **Title**: Initial Packet Processing Latency **Prerequisite Test**: N\A **Priority**: **Description**: In some virtual switch architectures, the first packets of a flow will take the system longer to process than subsequent packets in the flow. This test determines the latency for these packets. The test will measure the latency of the packets as they are processed by the flow-setup-path of the DUT. This test will send a single packet to the DUT after a fixed interval of time. The time interval will be equivalent to the amount of time it takes for a flow to time out in the virtual switch. Average packet latency will be determined over 1,000,000 packets. For this test, only unidirectional traffic is required. **Expected Result**: The average latency for the initial packet of all flows should be greater than the latency of subsequent traffic. **Metrics Collected**: The following are the metrics collected for this test: - Average latency of the initial packets of all flows that are processed by the DUT. **Deployment scenario**: - Physical → Virtual Switch → Physical.
---- ####2.3.3 Scalability tests The general aim of these tests is to understand the impact of large flow table size and flow lookups on throughput. The following list is not exhaustive but should indicate the type of tests that should be required. It is expected that more will be added.
- #####Test ID: LTD.Scalability.RFC2544.0PacketLoss **Title**: RFC 2544 0% loss Scalability throughput test **Prerequisite Test**: **Priority**: **Description**: The aim of this test is to measure how throughput changes as the number of flows in the DUT increases. For each frame size previously defined under [Default Test Parameters](#DefaultParams) and for each of the following number of flows: - 1,000 - 2,000 - 2,000 - 4,000 - 8,000 - 16,000 - 32,000 - 64,000 The maximum 0% packet loss throughput should be determined in a manner identical to LTD.Throughput.RFC2544.PacketLossRatio. **Expected Result**: **Metrics Collected**: The following are the metrics collected for this test: - The maximum number of frames per second that can be forwarded at the specified number of flows and the specified frame size, with zero packet loss.
---- [RFC1242]:(http://www.ietf.org/rfc/rfc1242.txt) [RFC2544]:(http://www.ietf.org/rfc/rfc2544.txt) [RFC2885]:(http://www.ietf.org/rfc/rfc2885.txt) [RFC2889]:(http://www.ietf.org/rfc/rfc2889.txt) [RFC5481]:(http://www.ietf.org/rfc/rfc5481.txt) [RFC6201]:(http://www.ietf.org/rfc/rfc6201.txt) [DPDK]:http://www.dpdk.org/