2 * include/linux/mfd/asic3.h
4 * Compaq ASIC3 headers.
6 * This program is free software; you can redistribute it and/or modify
7 * it under the terms of the GNU General Public License version 2 as
8 * published by the Free Software Foundation.
10 * Copyright 2001 Compaq Computer Corporation.
11 * Copyright 2007-2008 OpenedHand Ltd.
17 #include <linux/types.h>
22 const char *default_trigger;
23 struct led_classdev *cdev;
26 struct asic3_platform_data {
28 unsigned int gpio_config_num;
30 unsigned int irq_base;
32 unsigned int gpio_base;
34 unsigned int clock_rate;
36 struct asic3_led *leds;
39 #define ASIC3_NUM_GPIO_BANKS 4
40 #define ASIC3_GPIOS_PER_BANK 16
41 #define ASIC3_NUM_GPIOS 64
42 #define ASIC3_NR_IRQS ASIC3_NUM_GPIOS + 6
44 #define ASIC3_IRQ_LED0 64
45 #define ASIC3_IRQ_LED1 65
46 #define ASIC3_IRQ_LED2 66
47 #define ASIC3_IRQ_SPI 67
48 #define ASIC3_IRQ_SMBUS 68
49 #define ASIC3_IRQ_OWM 69
51 #define ASIC3_TO_GPIO(gpio) (NR_BUILTIN_GPIO + (gpio))
53 #define ASIC3_GPIO_BANK_A 0
54 #define ASIC3_GPIO_BANK_B 1
55 #define ASIC3_GPIO_BANK_C 2
56 #define ASIC3_GPIO_BANK_D 3
58 #define ASIC3_GPIO(bank, gpio) \
59 ((ASIC3_GPIOS_PER_BANK * ASIC3_GPIO_BANK_##bank) + (gpio))
60 #define ASIC3_GPIO_bit(gpio) (1 << (gpio & 0xf))
61 /* All offsets below are specified with this address bus shift */
62 #define ASIC3_DEFAULT_ADDR_SHIFT 2
64 #define ASIC3_OFFSET(base, reg) (ASIC3_##base##_BASE + ASIC3_##base##_##reg)
65 #define ASIC3_GPIO_OFFSET(base, reg) \
66 (ASIC3_GPIO_##base##_BASE + ASIC3_GPIO_##reg)
68 #define ASIC3_GPIO_A_BASE 0x0000
69 #define ASIC3_GPIO_B_BASE 0x0100
70 #define ASIC3_GPIO_C_BASE 0x0200
71 #define ASIC3_GPIO_D_BASE 0x0300
73 #define ASIC3_GPIO_TO_BANK(gpio) ((gpio) >> 4)
74 #define ASIC3_GPIO_TO_BIT(gpio) ((gpio) - \
75 (ASIC3_GPIOS_PER_BANK * ((gpio) >> 4)))
76 #define ASIC3_GPIO_TO_MASK(gpio) (1 << ASIC3_GPIO_TO_BIT(gpio))
77 #define ASIC3_GPIO_TO_BASE(gpio) (ASIC3_GPIO_A_BASE + (((gpio) >> 4) * 0x0100))
78 #define ASIC3_BANK_TO_BASE(bank) (ASIC3_GPIO_A_BASE + ((bank) * 0x100))
80 #define ASIC3_GPIO_MASK 0x00 /* R/W 0:don't mask */
81 #define ASIC3_GPIO_DIRECTION 0x04 /* R/W 0:input */
82 #define ASIC3_GPIO_OUT 0x08 /* R/W 0:output low */
83 #define ASIC3_GPIO_TRIGGER_TYPE 0x0c /* R/W 0:level */
84 #define ASIC3_GPIO_EDGE_TRIGGER 0x10 /* R/W 0:falling */
85 #define ASIC3_GPIO_LEVEL_TRIGGER 0x14 /* R/W 0:low level detect */
86 #define ASIC3_GPIO_SLEEP_MASK 0x18 /* R/W 0:don't mask in sleep mode */
87 #define ASIC3_GPIO_SLEEP_OUT 0x1c /* R/W level 0:low in sleep mode */
88 #define ASIC3_GPIO_BAT_FAULT_OUT 0x20 /* R/W level 0:low in batt_fault */
89 #define ASIC3_GPIO_INT_STATUS 0x24 /* R/W 0:none, 1:detect */
90 #define ASIC3_GPIO_ALT_FUNCTION 0x28 /* R/W 1:LED register control */
91 #define ASIC3_GPIO_SLEEP_CONF 0x2c /*
92 * R/W bit 1: autosleep
93 * 0: disable gposlpout in normal mode,
94 * enable gposlpout in sleep mode.
96 #define ASIC3_GPIO_STATUS 0x30 /* R Pin status */
101 * Bits 0..6 gpio number
102 * Bits 7..13 Alternate function
104 * Bit 15 Initial value
107 #define ASIC3_CONFIG_GPIO_PIN(config) ((config) & 0x7f)
108 #define ASIC3_CONFIG_GPIO_ALT(config) (((config) & (0x7f << 7)) >> 7)
109 #define ASIC3_CONFIG_GPIO_DIR(config) ((config & (1 << 14)) >> 14)
110 #define ASIC3_CONFIG_GPIO_INIT(config) ((config & (1 << 15)) >> 15)
111 #define ASIC3_CONFIG_GPIO(gpio, alt, dir, init) (((gpio) & 0x7f) \
112 | (((alt) & 0x7f) << 7) | (((dir) & 0x1) << 14) \
113 | (((init) & 0x1) << 15))
114 #define ASIC3_CONFIG_GPIO_DEFAULT(gpio, dir, init) \
115 ASIC3_CONFIG_GPIO((gpio), 0, (dir), (init))
116 #define ASIC3_CONFIG_GPIO_DEFAULT_OUT(gpio, init) \
117 ASIC3_CONFIG_GPIO((gpio), 0, 1, (init))
120 * Alternate functions
122 #define ASIC3_GPIOA11_PWM0 ASIC3_CONFIG_GPIO(11, 1, 1, 0)
123 #define ASIC3_GPIOA12_PWM1 ASIC3_CONFIG_GPIO(12, 1, 1, 0)
124 #define ASIC3_GPIOA15_CONTROL_CX ASIC3_CONFIG_GPIO(15, 1, 1, 0)
125 #define ASIC3_GPIOC0_LED0 ASIC3_CONFIG_GPIO(32, 1, 0, 0)
126 #define ASIC3_GPIOC1_LED1 ASIC3_CONFIG_GPIO(33, 1, 0, 0)
127 #define ASIC3_GPIOC2_LED2 ASIC3_CONFIG_GPIO(34, 1, 0, 0)
128 #define ASIC3_GPIOC3_SPI_RXD ASIC3_CONFIG_GPIO(35, 1, 0, 0)
129 #define ASIC3_GPIOC4_CF_nCD ASIC3_CONFIG_GPIO(36, 1, 0, 0)
130 #define ASIC3_GPIOC4_SPI_TXD ASIC3_CONFIG_GPIO(36, 1, 1, 0)
131 #define ASIC3_GPIOC5_SPI_CLK ASIC3_CONFIG_GPIO(37, 1, 1, 0)
132 #define ASIC3_GPIOC5_nCIOW ASIC3_CONFIG_GPIO(37, 1, 1, 0)
133 #define ASIC3_GPIOC6_nCIOR ASIC3_CONFIG_GPIO(38, 1, 1, 0)
134 #define ASIC3_GPIOC7_nPCE_1 ASIC3_CONFIG_GPIO(39, 1, 0, 0)
135 #define ASIC3_GPIOC8_nPCE_2 ASIC3_CONFIG_GPIO(40, 1, 0, 0)
136 #define ASIC3_GPIOC9_nPOE ASIC3_CONFIG_GPIO(41, 1, 0, 0)
137 #define ASIC3_GPIOC10_nPWE ASIC3_CONFIG_GPIO(42, 1, 0, 0)
138 #define ASIC3_GPIOC11_PSKTSEL ASIC3_CONFIG_GPIO(43, 1, 0, 0)
139 #define ASIC3_GPIOC12_nPREG ASIC3_CONFIG_GPIO(44, 1, 0, 0)
140 #define ASIC3_GPIOC13_nPWAIT ASIC3_CONFIG_GPIO(45, 1, 1, 0)
141 #define ASIC3_GPIOC14_nPIOIS16 ASIC3_CONFIG_GPIO(46, 1, 1, 0)
142 #define ASIC3_GPIOC15_nPIOR ASIC3_CONFIG_GPIO(47, 1, 0, 0)
143 #define ASIC3_GPIOD4_CF_nCD ASIC3_CONFIG_GPIO(52, 1, 0, 0)
144 #define ASIC3_GPIOD11_nCIOIS16 ASIC3_CONFIG_GPIO(59, 1, 0, 0)
145 #define ASIC3_GPIOD12_nCWAIT ASIC3_CONFIG_GPIO(60, 1, 0, 0)
146 #define ASIC3_GPIOD15_nPIOW ASIC3_CONFIG_GPIO(63, 1, 0, 0)
149 #define ASIC3_SPI_Base 0x0400
150 #define ASIC3_SPI_Control 0x0000
151 #define ASIC3_SPI_TxData 0x0004
152 #define ASIC3_SPI_RxData 0x0008
153 #define ASIC3_SPI_Int 0x000c
154 #define ASIC3_SPI_Status 0x0010
156 #define SPI_CONTROL_SPR(clk) ((clk) & 0x0f) /* Clock rate */
158 #define ASIC3_PWM_0_Base 0x0500
159 #define ASIC3_PWM_1_Base 0x0600
160 #define ASIC3_PWM_TimeBase 0x0000
161 #define ASIC3_PWM_PeriodTime 0x0004
162 #define ASIC3_PWM_DutyTime 0x0008
164 #define PWM_TIMEBASE_VALUE(x) ((x)&0xf) /* Low 4 bits sets time base */
165 #define PWM_TIMEBASE_ENABLE (1 << 4) /* Enable clock */
167 #define ASIC3_NUM_LEDS 3
168 #define ASIC3_LED_0_Base 0x0700
169 #define ASIC3_LED_1_Base 0x0800
170 #define ASIC3_LED_2_Base 0x0900
171 #define ASIC3_LED_TimeBase 0x0000 /* R/W 7 bits */
172 #define ASIC3_LED_PeriodTime 0x0004 /* R/W 12 bits */
173 #define ASIC3_LED_DutyTime 0x0008 /* R/W 12 bits */
174 #define ASIC3_LED_AutoStopCount 0x000c /* R/W 16 bits */
176 /* LED TimeBase bits - match ASIC2 */
177 #define LED_TBS 0x0f /* Low 4 bits sets time base, max = 13 */
178 /* Note: max = 5 on hx4700 */
179 /* 0: maximum time base */
180 /* 1: maximum time base / 2 */
181 /* n: maximum time base / 2^n */
183 #define LED_EN (1 << 4) /* LED ON/OFF 0:off, 1:on */
184 #define LED_AUTOSTOP (1 << 5) /* LED ON/OFF auto stop 0:disable, 1:enable */
185 #define LED_ALWAYS (1 << 6) /* LED Interrupt Mask 0:No mask, 1:mask */
187 #define ASIC3_CLOCK_BASE 0x0A00
188 #define ASIC3_CLOCK_CDEX 0x00
189 #define ASIC3_CLOCK_SEL 0x04
191 #define CLOCK_CDEX_SOURCE (1 << 0) /* 2 bits */
192 #define CLOCK_CDEX_SOURCE0 (1 << 0)
193 #define CLOCK_CDEX_SOURCE1 (1 << 1)
194 #define CLOCK_CDEX_SPI (1 << 2)
195 #define CLOCK_CDEX_OWM (1 << 3)
196 #define CLOCK_CDEX_PWM0 (1 << 4)
197 #define CLOCK_CDEX_PWM1 (1 << 5)
198 #define CLOCK_CDEX_LED0 (1 << 6)
199 #define CLOCK_CDEX_LED1 (1 << 7)
200 #define CLOCK_CDEX_LED2 (1 << 8)
202 /* Clocks settings: 1 for 24.576 MHz, 0 for 12.288Mhz */
203 #define CLOCK_CDEX_SD_HOST (1 << 9) /* R/W: SD host clock source */
204 #define CLOCK_CDEX_SD_BUS (1 << 10) /* R/W: SD bus clock source ctrl */
205 #define CLOCK_CDEX_SMBUS (1 << 11)
206 #define CLOCK_CDEX_CONTROL_CX (1 << 12)
208 #define CLOCK_CDEX_EX0 (1 << 13) /* R/W: 32.768 kHz crystal */
209 #define CLOCK_CDEX_EX1 (1 << 14) /* R/W: 24.576 MHz crystal */
211 #define CLOCK_SEL_SD_HCLK_SEL (1 << 0) /* R/W: SDIO host clock select */
212 #define CLOCK_SEL_SD_BCLK_SEL (1 << 1) /* R/W: SDIO bus clock select */
214 /* R/W: INT clock source control (32.768 kHz) */
215 #define CLOCK_SEL_CX (1 << 2)
218 #define ASIC3_INTR_BASE 0x0B00
220 #define ASIC3_INTR_INT_MASK 0x00 /* Interrupt mask control */
221 #define ASIC3_INTR_P_INT_STAT 0x04 /* Peripheral interrupt status */
222 #define ASIC3_INTR_INT_CPS 0x08 /* Interrupt timer clock pre-scale */
223 #define ASIC3_INTR_INT_TBS 0x0c /* Interrupt timer set */
225 #define ASIC3_INTMASK_GINTMASK (1 << 0) /* Global INTs mask 1:enable */
226 #define ASIC3_INTMASK_GINTEL (1 << 1) /* 1: rising edge, 0: hi level */
227 #define ASIC3_INTMASK_MASK0 (1 << 2)
228 #define ASIC3_INTMASK_MASK1 (1 << 3)
229 #define ASIC3_INTMASK_MASK2 (1 << 4)
230 #define ASIC3_INTMASK_MASK3 (1 << 5)
231 #define ASIC3_INTMASK_MASK4 (1 << 6)
232 #define ASIC3_INTMASK_MASK5 (1 << 7)
234 #define ASIC3_INTR_PERIPHERAL_A (1 << 0)
235 #define ASIC3_INTR_PERIPHERAL_B (1 << 1)
236 #define ASIC3_INTR_PERIPHERAL_C (1 << 2)
237 #define ASIC3_INTR_PERIPHERAL_D (1 << 3)
238 #define ASIC3_INTR_LED0 (1 << 4)
239 #define ASIC3_INTR_LED1 (1 << 5)
240 #define ASIC3_INTR_LED2 (1 << 6)
241 #define ASIC3_INTR_SPI (1 << 7)
242 #define ASIC3_INTR_SMBUS (1 << 8)
243 #define ASIC3_INTR_OWM (1 << 9)
245 #define ASIC3_INTR_CPS(x) ((x)&0x0f) /* 4 bits, max 14 */
246 #define ASIC3_INTR_CPS_SET (1 << 4) /* Time base enable */
249 /* Basic control of the SD ASIC */
250 #define ASIC3_SDHWCTRL_BASE 0x0E00
251 #define ASIC3_SDHWCTRL_SDCONF 0x00
253 #define ASIC3_SDHWCTRL_SUSPEND (1 << 0) /* 1=suspend all SD operations */
254 #define ASIC3_SDHWCTRL_CLKSEL (1 << 1) /* 1=SDICK, 0=HCLK */
255 #define ASIC3_SDHWCTRL_PCLR (1 << 2) /* All registers of SDIO cleared */
256 #define ASIC3_SDHWCTRL_LEVCD (1 << 3) /* SD card detection: 0:low */
258 /* SD card write protection: 0=high */
259 #define ASIC3_SDHWCTRL_LEVWP (1 << 4)
260 #define ASIC3_SDHWCTRL_SDLED (1 << 5) /* SD card LED signal 0=disable */
262 /* SD card power supply ctrl 1=enable */
263 #define ASIC3_SDHWCTRL_SDPWR (1 << 6)
265 #define ASIC3_EXTCF_BASE 0x1100
267 #define ASIC3_EXTCF_SELECT 0x00
268 #define ASIC3_EXTCF_RESET 0x04
270 #define ASIC3_EXTCF_SMOD0 (1 << 0) /* slot number of mode 0 */
271 #define ASIC3_EXTCF_SMOD1 (1 << 1) /* slot number of mode 1 */
272 #define ASIC3_EXTCF_SMOD2 (1 << 2) /* slot number of mode 2 */
273 #define ASIC3_EXTCF_OWM_EN (1 << 4) /* enable onewire module */
274 #define ASIC3_EXTCF_OWM_SMB (1 << 5) /* OWM bus selection */
275 #define ASIC3_EXTCF_OWM_RESET (1 << 6) /* ?? used by OWM and CF */
276 #define ASIC3_EXTCF_CF0_SLEEP_MODE (1 << 7) /* CF0 sleep state */
277 #define ASIC3_EXTCF_CF1_SLEEP_MODE (1 << 8) /* CF1 sleep state */
278 #define ASIC3_EXTCF_CF0_PWAIT_EN (1 << 10) /* CF0 PWAIT_n control */
279 #define ASIC3_EXTCF_CF1_PWAIT_EN (1 << 11) /* CF1 PWAIT_n control */
280 #define ASIC3_EXTCF_CF0_BUF_EN (1 << 12) /* CF0 buffer control */
281 #define ASIC3_EXTCF_CF1_BUF_EN (1 << 13) /* CF1 buffer control */
282 #define ASIC3_EXTCF_SD_MEM_ENABLE (1 << 14)
283 #define ASIC3_EXTCF_CF_SLEEP (1 << 15) /* CF sleep mode control */
285 /*********************************************
286 * The Onewire interface (DS1WM) is handled
287 * by the ds1wm driver.
289 *********************************************/
291 #define ASIC3_OWM_BASE 0xC00
293 /*****************************************************************************
294 * The SD configuration registers are at a completely different location
295 * in memory. They are divided into three sets of registers:
297 * SD_CONFIG Core configuration register
298 * SD_CTRL Control registers for SD operations
299 * SDIO_CTRL Control registers for SDIO operations
301 *****************************************************************************/
302 #define ASIC3_SD_CONFIG_BASE 0x0400 /* Assumes 32 bit addressing */
303 #define ASIC3_SD_CONFIG_SIZE 0x0200 /* Assumes 32 bit addressing */
304 #define ASIC3_SD_CTRL_BASE 0x1000
305 #define ASIC3_SDIO_CTRL_BASE 0x1200
307 #define ASIC3_MAP_SIZE_32BIT 0x2000
308 #define ASIC3_MAP_SIZE_16BIT 0x1000
310 /* Functions needed by leds-asic3 */
313 extern void asic3_write_register(struct asic3 *asic, unsigned int reg, u32 val);
314 extern u32 asic3_read_register(struct asic3 *asic, unsigned int reg);
316 #endif /* __ASIC3_H__ */