1d17b5872dd1f266625891b600d673c98a8cfa0f
[kvmfornfv.git] / kernel / drivers / net / ethernet / intel / ixgbe / ixgbe_sriov.c
1 /*******************************************************************************
2
3   Intel 10 Gigabit PCI Express Linux driver
4   Copyright(c) 1999 - 2014 Intel Corporation.
5
6   This program is free software; you can redistribute it and/or modify it
7   under the terms and conditions of the GNU General Public License,
8   version 2, as published by the Free Software Foundation.
9
10   This program is distributed in the hope it will be useful, but WITHOUT
11   ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
12   FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
13   more details.
14
15   You should have received a copy of the GNU General Public License along with
16   this program; if not, write to the Free Software Foundation, Inc.,
17   51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
18
19   The full GNU General Public License is included in this distribution in
20   the file called "COPYING".
21
22   Contact Information:
23   Linux NICS <linux.nics@intel.com>
24   e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
25   Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
26
27 *******************************************************************************/
28
29 #include <linux/types.h>
30 #include <linux/module.h>
31 #include <linux/pci.h>
32 #include <linux/netdevice.h>
33 #include <linux/vmalloc.h>
34 #include <linux/string.h>
35 #include <linux/in.h>
36 #include <linux/ip.h>
37 #include <linux/tcp.h>
38 #include <linux/ipv6.h>
39 #include <linux/if_bridge.h>
40 #ifdef NETIF_F_HW_VLAN_CTAG_TX
41 #include <linux/if_vlan.h>
42 #endif
43
44 #include "ixgbe.h"
45 #include "ixgbe_type.h"
46 #include "ixgbe_sriov.h"
47
48 #ifdef CONFIG_PCI_IOV
49 static int __ixgbe_enable_sriov(struct ixgbe_adapter *adapter)
50 {
51         struct ixgbe_hw *hw = &adapter->hw;
52         int num_vf_macvlans, i;
53         struct vf_macvlans *mv_list;
54
55         adapter->flags |= IXGBE_FLAG_SRIOV_ENABLED;
56         e_info(probe, "SR-IOV enabled with %d VFs\n", adapter->num_vfs);
57
58         /* Enable VMDq flag so device will be set in VM mode */
59         adapter->flags |= IXGBE_FLAG_VMDQ_ENABLED;
60         if (!adapter->ring_feature[RING_F_VMDQ].limit)
61                 adapter->ring_feature[RING_F_VMDQ].limit = 1;
62         adapter->ring_feature[RING_F_VMDQ].offset = adapter->num_vfs;
63
64         num_vf_macvlans = hw->mac.num_rar_entries -
65         (IXGBE_MAX_PF_MACVLANS + 1 + adapter->num_vfs);
66
67         adapter->mv_list = mv_list = kcalloc(num_vf_macvlans,
68                                              sizeof(struct vf_macvlans),
69                                              GFP_KERNEL);
70         if (mv_list) {
71                 /* Initialize list of VF macvlans */
72                 INIT_LIST_HEAD(&adapter->vf_mvs.l);
73                 for (i = 0; i < num_vf_macvlans; i++) {
74                         mv_list->vf = -1;
75                         mv_list->free = true;
76                         list_add(&mv_list->l, &adapter->vf_mvs.l);
77                         mv_list++;
78                 }
79         }
80
81         /* Initialize default switching mode VEB */
82         IXGBE_WRITE_REG(hw, IXGBE_PFDTXGSWC, IXGBE_PFDTXGSWC_VT_LBEN);
83         adapter->bridge_mode = BRIDGE_MODE_VEB;
84
85         /* If call to enable VFs succeeded then allocate memory
86          * for per VF control structures.
87          */
88         adapter->vfinfo =
89                 kcalloc(adapter->num_vfs,
90                         sizeof(struct vf_data_storage), GFP_KERNEL);
91         if (adapter->vfinfo) {
92                 /* limit trafffic classes based on VFs enabled */
93                 if ((adapter->hw.mac.type == ixgbe_mac_82599EB) &&
94                     (adapter->num_vfs < 16)) {
95                         adapter->dcb_cfg.num_tcs.pg_tcs = MAX_TRAFFIC_CLASS;
96                         adapter->dcb_cfg.num_tcs.pfc_tcs = MAX_TRAFFIC_CLASS;
97                 } else if (adapter->num_vfs < 32) {
98                         adapter->dcb_cfg.num_tcs.pg_tcs = 4;
99                         adapter->dcb_cfg.num_tcs.pfc_tcs = 4;
100                 } else {
101                         adapter->dcb_cfg.num_tcs.pg_tcs = 1;
102                         adapter->dcb_cfg.num_tcs.pfc_tcs = 1;
103                 }
104
105                 /* Disable RSC when in SR-IOV mode */
106                 adapter->flags2 &= ~(IXGBE_FLAG2_RSC_CAPABLE |
107                                      IXGBE_FLAG2_RSC_ENABLED);
108
109                 for (i = 0; i < adapter->num_vfs; i++) {
110                         /* enable spoof checking for all VFs */
111                         adapter->vfinfo[i].spoofchk_enabled = true;
112
113                         /* We support VF RSS querying only for 82599 and x540
114                          * devices at the moment. These devices share RSS
115                          * indirection table and RSS hash key with PF therefore
116                          * we want to disable the querying by default.
117                          */
118                         adapter->vfinfo[i].rss_query_enabled = 0;
119                 }
120
121                 return 0;
122         }
123
124         return -ENOMEM;
125 }
126
127 /* Note this function is called when the user wants to enable SR-IOV
128  * VFs using the now deprecated module parameter
129  */
130 void ixgbe_enable_sriov(struct ixgbe_adapter *adapter)
131 {
132         int pre_existing_vfs = 0;
133
134         pre_existing_vfs = pci_num_vf(adapter->pdev);
135         if (!pre_existing_vfs && !adapter->num_vfs)
136                 return;
137
138         /* If there are pre-existing VFs then we have to force
139          * use of that many - over ride any module parameter value.
140          * This may result from the user unloading the PF driver
141          * while VFs were assigned to guest VMs or because the VFs
142          * have been created via the new PCI SR-IOV sysfs interface.
143          */
144         if (pre_existing_vfs) {
145                 adapter->num_vfs = pre_existing_vfs;
146                 dev_warn(&adapter->pdev->dev,
147                          "Virtual Functions already enabled for this device - Please reload all VF drivers to avoid spoofed packet errors\n");
148         } else {
149                 int err;
150                 /*
151                  * The 82599 supports up to 64 VFs per physical function
152                  * but this implementation limits allocation to 63 so that
153                  * basic networking resources are still available to the
154                  * physical function.  If the user requests greater than
155                  * 63 VFs then it is an error - reset to default of zero.
156                  */
157                 adapter->num_vfs = min_t(unsigned int, adapter->num_vfs, IXGBE_MAX_VFS_DRV_LIMIT);
158
159                 err = pci_enable_sriov(adapter->pdev, adapter->num_vfs);
160                 if (err) {
161                         e_err(probe, "Failed to enable PCI sriov: %d\n", err);
162                         adapter->num_vfs = 0;
163                         return;
164                 }
165         }
166
167         if (!__ixgbe_enable_sriov(adapter))
168                 return;
169
170         /* If we have gotten to this point then there is no memory available
171          * to manage the VF devices - print message and bail.
172          */
173         e_err(probe, "Unable to allocate memory for VF Data Storage - "
174               "SRIOV disabled\n");
175         ixgbe_disable_sriov(adapter);
176 }
177
178 #endif /* #ifdef CONFIG_PCI_IOV */
179 int ixgbe_disable_sriov(struct ixgbe_adapter *adapter)
180 {
181         struct ixgbe_hw *hw = &adapter->hw;
182         u32 gpie;
183         u32 vmdctl;
184         int rss;
185
186         /* set num VFs to 0 to prevent access to vfinfo */
187         adapter->num_vfs = 0;
188
189         /* free VF control structures */
190         kfree(adapter->vfinfo);
191         adapter->vfinfo = NULL;
192
193         /* free macvlan list */
194         kfree(adapter->mv_list);
195         adapter->mv_list = NULL;
196
197         /* if SR-IOV is already disabled then there is nothing to do */
198         if (!(adapter->flags & IXGBE_FLAG_SRIOV_ENABLED))
199                 return 0;
200
201 #ifdef CONFIG_PCI_IOV
202         /*
203          * If our VFs are assigned we cannot shut down SR-IOV
204          * without causing issues, so just leave the hardware
205          * available but disabled
206          */
207         if (pci_vfs_assigned(adapter->pdev)) {
208                 e_dev_warn("Unloading driver while VFs are assigned - VFs will not be deallocated\n");
209                 return -EPERM;
210         }
211         /* disable iov and allow time for transactions to clear */
212         pci_disable_sriov(adapter->pdev);
213 #endif
214
215         /* turn off device IOV mode */
216         IXGBE_WRITE_REG(hw, IXGBE_GCR_EXT, 0);
217         gpie = IXGBE_READ_REG(hw, IXGBE_GPIE);
218         gpie &= ~IXGBE_GPIE_VTMODE_MASK;
219         IXGBE_WRITE_REG(hw, IXGBE_GPIE, gpie);
220
221         /* set default pool back to 0 */
222         vmdctl = IXGBE_READ_REG(hw, IXGBE_VT_CTL);
223         vmdctl &= ~IXGBE_VT_CTL_POOL_MASK;
224         IXGBE_WRITE_REG(hw, IXGBE_VT_CTL, vmdctl);
225         IXGBE_WRITE_FLUSH(hw);
226
227         /* Disable VMDq flag so device will be set in VM mode */
228         if (adapter->ring_feature[RING_F_VMDQ].limit == 1) {
229                 adapter->flags &= ~IXGBE_FLAG_VMDQ_ENABLED;
230                 adapter->flags &= ~IXGBE_FLAG_SRIOV_ENABLED;
231                 rss = min_t(int, ixgbe_max_rss_indices(adapter),
232                             num_online_cpus());
233         } else {
234                 rss = min_t(int, IXGBE_MAX_L2A_QUEUES, num_online_cpus());
235         }
236
237         adapter->ring_feature[RING_F_VMDQ].offset = 0;
238         adapter->ring_feature[RING_F_RSS].limit = rss;
239
240         /* take a breather then clean up driver data */
241         msleep(100);
242         return 0;
243 }
244
245 static int ixgbe_pci_sriov_enable(struct pci_dev *dev, int num_vfs)
246 {
247 #ifdef CONFIG_PCI_IOV
248         struct ixgbe_adapter *adapter = pci_get_drvdata(dev);
249         int err = 0;
250         int i;
251         int pre_existing_vfs = pci_num_vf(dev);
252
253         if (pre_existing_vfs && pre_existing_vfs != num_vfs)
254                 err = ixgbe_disable_sriov(adapter);
255         else if (pre_existing_vfs && pre_existing_vfs == num_vfs)
256                 return num_vfs;
257
258         if (err)
259                 return err;
260
261         /* While the SR-IOV capability structure reports total VFs to be 64,
262          * we have to limit the actual number allocated based on two factors.
263          * First, we reserve some transmit/receive resources for the PF.
264          * Second, VMDQ also uses the same pools that SR-IOV does. We need to
265          * account for this, so that we don't accidentally allocate more VFs
266          * than we have available pools. The PCI bus driver already checks for
267          * other values out of range.
268          */
269         if ((num_vfs + adapter->num_rx_pools) > IXGBE_MAX_VF_FUNCTIONS)
270                 return -EPERM;
271
272         adapter->num_vfs = num_vfs;
273
274         err = __ixgbe_enable_sriov(adapter);
275         if (err)
276                 return  err;
277
278         for (i = 0; i < adapter->num_vfs; i++)
279                 ixgbe_vf_configuration(dev, (i | 0x10000000));
280
281         err = pci_enable_sriov(dev, num_vfs);
282         if (err) {
283                 e_dev_warn("Failed to enable PCI sriov: %d\n", err);
284                 return err;
285         }
286         ixgbe_sriov_reinit(adapter);
287
288         return num_vfs;
289 #else
290         return 0;
291 #endif
292 }
293
294 static int ixgbe_pci_sriov_disable(struct pci_dev *dev)
295 {
296         struct ixgbe_adapter *adapter = pci_get_drvdata(dev);
297         int err;
298 #ifdef CONFIG_PCI_IOV
299         u32 current_flags = adapter->flags;
300 #endif
301
302         err = ixgbe_disable_sriov(adapter);
303
304         /* Only reinit if no error and state changed */
305 #ifdef CONFIG_PCI_IOV
306         if (!err && current_flags != adapter->flags)
307                 ixgbe_sriov_reinit(adapter);
308 #endif
309
310         return err;
311 }
312
313 int ixgbe_pci_sriov_configure(struct pci_dev *dev, int num_vfs)
314 {
315         if (num_vfs == 0)
316                 return ixgbe_pci_sriov_disable(dev);
317         else
318                 return ixgbe_pci_sriov_enable(dev, num_vfs);
319 }
320
321 static int ixgbe_set_vf_multicasts(struct ixgbe_adapter *adapter,
322                                    u32 *msgbuf, u32 vf)
323 {
324         int entries = (msgbuf[0] & IXGBE_VT_MSGINFO_MASK)
325                        >> IXGBE_VT_MSGINFO_SHIFT;
326         u16 *hash_list = (u16 *)&msgbuf[1];
327         struct vf_data_storage *vfinfo = &adapter->vfinfo[vf];
328         struct ixgbe_hw *hw = &adapter->hw;
329         int i;
330         u32 vector_bit;
331         u32 vector_reg;
332         u32 mta_reg;
333         u32 vmolr = IXGBE_READ_REG(hw, IXGBE_VMOLR(vf));
334
335         /* only so many hash values supported */
336         entries = min(entries, IXGBE_MAX_VF_MC_ENTRIES);
337
338         /*
339          * salt away the number of multi cast addresses assigned
340          * to this VF for later use to restore when the PF multi cast
341          * list changes
342          */
343         vfinfo->num_vf_mc_hashes = entries;
344
345         /*
346          * VFs are limited to using the MTA hash table for their multicast
347          * addresses
348          */
349         for (i = 0; i < entries; i++) {
350                 vfinfo->vf_mc_hashes[i] = hash_list[i];
351         }
352
353         for (i = 0; i < vfinfo->num_vf_mc_hashes; i++) {
354                 vector_reg = (vfinfo->vf_mc_hashes[i] >> 5) & 0x7F;
355                 vector_bit = vfinfo->vf_mc_hashes[i] & 0x1F;
356                 mta_reg = IXGBE_READ_REG(hw, IXGBE_MTA(vector_reg));
357                 mta_reg |= (1 << vector_bit);
358                 IXGBE_WRITE_REG(hw, IXGBE_MTA(vector_reg), mta_reg);
359         }
360         vmolr |= IXGBE_VMOLR_ROMPE;
361         IXGBE_WRITE_REG(hw, IXGBE_VMOLR(vf), vmolr);
362
363         return 0;
364 }
365
366 #ifdef CONFIG_PCI_IOV
367 void ixgbe_restore_vf_multicasts(struct ixgbe_adapter *adapter)
368 {
369         struct ixgbe_hw *hw = &adapter->hw;
370         struct vf_data_storage *vfinfo;
371         int i, j;
372         u32 vector_bit;
373         u32 vector_reg;
374         u32 mta_reg;
375
376         for (i = 0; i < adapter->num_vfs; i++) {
377                 u32 vmolr = IXGBE_READ_REG(hw, IXGBE_VMOLR(i));
378                 vfinfo = &adapter->vfinfo[i];
379                 for (j = 0; j < vfinfo->num_vf_mc_hashes; j++) {
380                         hw->addr_ctrl.mta_in_use++;
381                         vector_reg = (vfinfo->vf_mc_hashes[j] >> 5) & 0x7F;
382                         vector_bit = vfinfo->vf_mc_hashes[j] & 0x1F;
383                         mta_reg = IXGBE_READ_REG(hw, IXGBE_MTA(vector_reg));
384                         mta_reg |= (1 << vector_bit);
385                         IXGBE_WRITE_REG(hw, IXGBE_MTA(vector_reg), mta_reg);
386                 }
387
388                 if (vfinfo->num_vf_mc_hashes)
389                         vmolr |= IXGBE_VMOLR_ROMPE;
390                 else
391                         vmolr &= ~IXGBE_VMOLR_ROMPE;
392                 IXGBE_WRITE_REG(hw, IXGBE_VMOLR(i), vmolr);
393         }
394
395         /* Restore any VF macvlans */
396         ixgbe_full_sync_mac_table(adapter);
397 }
398 #endif
399
400 static int ixgbe_set_vf_vlan(struct ixgbe_adapter *adapter, int add, int vid,
401                              u32 vf)
402 {
403         /* VLAN 0 is a special case, don't allow it to be removed */
404         if (!vid && !add)
405                 return 0;
406
407         return adapter->hw.mac.ops.set_vfta(&adapter->hw, vid, vf, (bool)add);
408 }
409
410 static s32 ixgbe_set_vf_lpe(struct ixgbe_adapter *adapter, u32 *msgbuf, u32 vf)
411 {
412         struct ixgbe_hw *hw = &adapter->hw;
413         int max_frame = msgbuf[1];
414         u32 max_frs;
415
416         /*
417          * For 82599EB we have to keep all PFs and VFs operating with
418          * the same max_frame value in order to avoid sending an oversize
419          * frame to a VF.  In order to guarantee this is handled correctly
420          * for all cases we have several special exceptions to take into
421          * account before we can enable the VF for receive
422          */
423         if (adapter->hw.mac.type == ixgbe_mac_82599EB) {
424                 struct net_device *dev = adapter->netdev;
425                 int pf_max_frame = dev->mtu + ETH_HLEN;
426                 u32 reg_offset, vf_shift, vfre;
427                 s32 err = 0;
428
429 #ifdef CONFIG_FCOE
430                 if (dev->features & NETIF_F_FCOE_MTU)
431                         pf_max_frame = max_t(int, pf_max_frame,
432                                              IXGBE_FCOE_JUMBO_FRAME_SIZE);
433
434 #endif /* CONFIG_FCOE */
435                 switch (adapter->vfinfo[vf].vf_api) {
436                 case ixgbe_mbox_api_11:
437                 case ixgbe_mbox_api_12:
438                         /*
439                          * Version 1.1 supports jumbo frames on VFs if PF has
440                          * jumbo frames enabled which means legacy VFs are
441                          * disabled
442                          */
443                         if (pf_max_frame > ETH_FRAME_LEN)
444                                 break;
445                 default:
446                         /*
447                          * If the PF or VF are running w/ jumbo frames enabled
448                          * we need to shut down the VF Rx path as we cannot
449                          * support jumbo frames on legacy VFs
450                          */
451                         if ((pf_max_frame > ETH_FRAME_LEN) ||
452                             (max_frame > (ETH_FRAME_LEN + ETH_FCS_LEN)))
453                                 err = -EINVAL;
454                         break;
455                 }
456
457                 /* determine VF receive enable location */
458                 vf_shift = vf % 32;
459                 reg_offset = vf / 32;
460
461                 /* enable or disable receive depending on error */
462                 vfre = IXGBE_READ_REG(hw, IXGBE_VFRE(reg_offset));
463                 if (err)
464                         vfre &= ~(1 << vf_shift);
465                 else
466                         vfre |= 1 << vf_shift;
467                 IXGBE_WRITE_REG(hw, IXGBE_VFRE(reg_offset), vfre);
468
469                 if (err) {
470                         e_err(drv, "VF max_frame %d out of range\n", max_frame);
471                         return err;
472                 }
473         }
474
475         /* MTU < 68 is an error and causes problems on some kernels */
476         if (max_frame > IXGBE_MAX_JUMBO_FRAME_SIZE) {
477                 e_err(drv, "VF max_frame %d out of range\n", max_frame);
478                 return -EINVAL;
479         }
480
481         /* pull current max frame size from hardware */
482         max_frs = IXGBE_READ_REG(hw, IXGBE_MAXFRS);
483         max_frs &= IXGBE_MHADD_MFS_MASK;
484         max_frs >>= IXGBE_MHADD_MFS_SHIFT;
485
486         if (max_frs < max_frame) {
487                 max_frs = max_frame << IXGBE_MHADD_MFS_SHIFT;
488                 IXGBE_WRITE_REG(hw, IXGBE_MAXFRS, max_frs);
489         }
490
491         e_info(hw, "VF requests change max MTU to %d\n", max_frame);
492
493         return 0;
494 }
495
496 static void ixgbe_set_vmolr(struct ixgbe_hw *hw, u32 vf, bool aupe)
497 {
498         u32 vmolr = IXGBE_READ_REG(hw, IXGBE_VMOLR(vf));
499         vmolr |= IXGBE_VMOLR_BAM;
500         if (aupe)
501                 vmolr |= IXGBE_VMOLR_AUPE;
502         else
503                 vmolr &= ~IXGBE_VMOLR_AUPE;
504         IXGBE_WRITE_REG(hw, IXGBE_VMOLR(vf), vmolr);
505 }
506
507 static void ixgbe_clear_vmvir(struct ixgbe_adapter *adapter, u32 vf)
508 {
509         struct ixgbe_hw *hw = &adapter->hw;
510
511         IXGBE_WRITE_REG(hw, IXGBE_VMVIR(vf), 0);
512 }
513 static inline void ixgbe_vf_reset_event(struct ixgbe_adapter *adapter, u32 vf)
514 {
515         struct ixgbe_hw *hw = &adapter->hw;
516         struct vf_data_storage *vfinfo = &adapter->vfinfo[vf];
517         u8 num_tcs = netdev_get_num_tc(adapter->netdev);
518
519         /* add PF assigned VLAN or VLAN 0 */
520         ixgbe_set_vf_vlan(adapter, true, vfinfo->pf_vlan, vf);
521
522         /* reset offloads to defaults */
523         ixgbe_set_vmolr(hw, vf, !vfinfo->pf_vlan);
524
525         /* set outgoing tags for VFs */
526         if (!vfinfo->pf_vlan && !vfinfo->pf_qos && !num_tcs) {
527                 ixgbe_clear_vmvir(adapter, vf);
528         } else {
529                 if (vfinfo->pf_qos || !num_tcs)
530                         ixgbe_set_vmvir(adapter, vfinfo->pf_vlan,
531                                         vfinfo->pf_qos, vf);
532                 else
533                         ixgbe_set_vmvir(adapter, vfinfo->pf_vlan,
534                                         adapter->default_up, vf);
535
536                 if (vfinfo->spoofchk_enabled)
537                         hw->mac.ops.set_vlan_anti_spoofing(hw, true, vf);
538         }
539
540         /* reset multicast table array for vf */
541         adapter->vfinfo[vf].num_vf_mc_hashes = 0;
542
543         /* Flush and reset the mta with the new values */
544         ixgbe_set_rx_mode(adapter->netdev);
545
546         ixgbe_del_mac_filter(adapter, adapter->vfinfo[vf].vf_mac_addresses, vf);
547
548         /* reset VF api back to unknown */
549         adapter->vfinfo[vf].vf_api = ixgbe_mbox_api_10;
550 }
551
552 static int ixgbe_set_vf_mac(struct ixgbe_adapter *adapter,
553                             int vf, unsigned char *mac_addr)
554 {
555         ixgbe_del_mac_filter(adapter, adapter->vfinfo[vf].vf_mac_addresses, vf);
556         memcpy(adapter->vfinfo[vf].vf_mac_addresses, mac_addr, ETH_ALEN);
557         ixgbe_add_mac_filter(adapter, adapter->vfinfo[vf].vf_mac_addresses, vf);
558
559         return 0;
560 }
561
562 static int ixgbe_set_vf_macvlan(struct ixgbe_adapter *adapter,
563                                 int vf, int index, unsigned char *mac_addr)
564 {
565         struct list_head *pos;
566         struct vf_macvlans *entry;
567
568         if (index <= 1) {
569                 list_for_each(pos, &adapter->vf_mvs.l) {
570                         entry = list_entry(pos, struct vf_macvlans, l);
571                         if (entry->vf == vf) {
572                                 entry->vf = -1;
573                                 entry->free = true;
574                                 entry->is_macvlan = false;
575                                 ixgbe_del_mac_filter(adapter,
576                                                      entry->vf_macvlan, vf);
577                         }
578                 }
579         }
580
581         /*
582          * If index was zero then we were asked to clear the uc list
583          * for the VF.  We're done.
584          */
585         if (!index)
586                 return 0;
587
588         entry = NULL;
589
590         list_for_each(pos, &adapter->vf_mvs.l) {
591                 entry = list_entry(pos, struct vf_macvlans, l);
592                 if (entry->free)
593                         break;
594         }
595
596         /*
597          * If we traversed the entire list and didn't find a free entry
598          * then we're out of space on the RAR table.  Also entry may
599          * be NULL because the original memory allocation for the list
600          * failed, which is not fatal but does mean we can't support
601          * VF requests for MACVLAN because we couldn't allocate
602          * memory for the list management required.
603          */
604         if (!entry || !entry->free)
605                 return -ENOSPC;
606
607         entry->free = false;
608         entry->is_macvlan = true;
609         entry->vf = vf;
610         memcpy(entry->vf_macvlan, mac_addr, ETH_ALEN);
611
612         ixgbe_add_mac_filter(adapter, mac_addr, vf);
613
614         return 0;
615 }
616
617 int ixgbe_vf_configuration(struct pci_dev *pdev, unsigned int event_mask)
618 {
619         struct ixgbe_adapter *adapter = pci_get_drvdata(pdev);
620         unsigned int vfn = (event_mask & 0x3f);
621
622         bool enable = ((event_mask & 0x10000000U) != 0);
623
624         if (enable)
625                 eth_zero_addr(adapter->vfinfo[vfn].vf_mac_addresses);
626
627         return 0;
628 }
629
630 static inline void ixgbe_write_qde(struct ixgbe_adapter *adapter, u32 vf,
631                                    u32 qde)
632 {
633         struct ixgbe_hw *hw = &adapter->hw;
634         struct ixgbe_ring_feature *vmdq = &adapter->ring_feature[RING_F_VMDQ];
635         u32 q_per_pool = __ALIGN_MASK(1, ~vmdq->mask);
636         int i;
637
638         for (i = vf * q_per_pool; i < ((vf + 1) * q_per_pool); i++) {
639                 u32 reg;
640
641                 /* flush previous write */
642                 IXGBE_WRITE_FLUSH(hw);
643
644                 /* indicate to hardware that we want to set drop enable */
645                 reg = IXGBE_QDE_WRITE | IXGBE_QDE_ENABLE;
646                 reg |= i <<  IXGBE_QDE_IDX_SHIFT;
647                 IXGBE_WRITE_REG(hw, IXGBE_QDE, reg);
648         }
649 }
650
651 static int ixgbe_vf_reset_msg(struct ixgbe_adapter *adapter, u32 vf)
652 {
653         struct ixgbe_ring_feature *vmdq = &adapter->ring_feature[RING_F_VMDQ];
654         struct ixgbe_hw *hw = &adapter->hw;
655         unsigned char *vf_mac = adapter->vfinfo[vf].vf_mac_addresses;
656         u32 reg, reg_offset, vf_shift;
657         u32 msgbuf[4] = {0, 0, 0, 0};
658         u8 *addr = (u8 *)(&msgbuf[1]);
659         u32 q_per_pool = __ALIGN_MASK(1, ~vmdq->mask);
660         int i;
661
662         e_info(probe, "VF Reset msg received from vf %d\n", vf);
663
664         /* reset the filters for the device */
665         ixgbe_vf_reset_event(adapter, vf);
666
667         /* set vf mac address */
668         if (!is_zero_ether_addr(vf_mac))
669                 ixgbe_set_vf_mac(adapter, vf, vf_mac);
670
671         vf_shift = vf % 32;
672         reg_offset = vf / 32;
673
674         /* enable transmit for vf */
675         reg = IXGBE_READ_REG(hw, IXGBE_VFTE(reg_offset));
676         reg |= 1 << vf_shift;
677         IXGBE_WRITE_REG(hw, IXGBE_VFTE(reg_offset), reg);
678
679         /* force drop enable for all VF Rx queues */
680         ixgbe_write_qde(adapter, vf, IXGBE_QDE_ENABLE);
681
682         /* enable receive for vf */
683         reg = IXGBE_READ_REG(hw, IXGBE_VFRE(reg_offset));
684         reg |= 1 << vf_shift;
685         /*
686          * The 82599 cannot support a mix of jumbo and non-jumbo PF/VFs.
687          * For more info take a look at ixgbe_set_vf_lpe
688          */
689         if (adapter->hw.mac.type == ixgbe_mac_82599EB) {
690                 struct net_device *dev = adapter->netdev;
691                 int pf_max_frame = dev->mtu + ETH_HLEN;
692
693 #ifdef CONFIG_FCOE
694                 if (dev->features & NETIF_F_FCOE_MTU)
695                         pf_max_frame = max_t(int, pf_max_frame,
696                                              IXGBE_FCOE_JUMBO_FRAME_SIZE);
697
698 #endif /* CONFIG_FCOE */
699                 if (pf_max_frame > ETH_FRAME_LEN)
700                         reg &= ~(1 << vf_shift);
701         }
702         IXGBE_WRITE_REG(hw, IXGBE_VFRE(reg_offset), reg);
703
704         /* enable VF mailbox for further messages */
705         adapter->vfinfo[vf].clear_to_send = true;
706
707         /* Enable counting of spoofed packets in the SSVPC register */
708         reg = IXGBE_READ_REG(hw, IXGBE_VMECM(reg_offset));
709         reg |= (1 << vf_shift);
710         IXGBE_WRITE_REG(hw, IXGBE_VMECM(reg_offset), reg);
711
712         /*
713          * Reset the VFs TDWBAL and TDWBAH registers
714          * which are not cleared by an FLR
715          */
716         for (i = 0; i < q_per_pool; i++) {
717                 IXGBE_WRITE_REG(hw, IXGBE_PVFTDWBAHn(q_per_pool, vf, i), 0);
718                 IXGBE_WRITE_REG(hw, IXGBE_PVFTDWBALn(q_per_pool, vf, i), 0);
719         }
720
721         /* reply to reset with ack and vf mac address */
722         msgbuf[0] = IXGBE_VF_RESET;
723         if (!is_zero_ether_addr(vf_mac)) {
724                 msgbuf[0] |= IXGBE_VT_MSGTYPE_ACK;
725                 memcpy(addr, vf_mac, ETH_ALEN);
726         } else {
727                 msgbuf[0] |= IXGBE_VT_MSGTYPE_NACK;
728                 dev_warn(&adapter->pdev->dev,
729                          "VF %d has no MAC address assigned, you may have to assign one manually\n",
730                          vf);
731         }
732
733         /*
734          * Piggyback the multicast filter type so VF can compute the
735          * correct vectors
736          */
737         msgbuf[3] = hw->mac.mc_filter_type;
738         ixgbe_write_mbx(hw, msgbuf, IXGBE_VF_PERMADDR_MSG_LEN, vf);
739
740         return 0;
741 }
742
743 static int ixgbe_set_vf_mac_addr(struct ixgbe_adapter *adapter,
744                                  u32 *msgbuf, u32 vf)
745 {
746         u8 *new_mac = ((u8 *)(&msgbuf[1]));
747
748         if (!is_valid_ether_addr(new_mac)) {
749                 e_warn(drv, "VF %d attempted to set invalid mac\n", vf);
750                 return -1;
751         }
752
753         if (adapter->vfinfo[vf].pf_set_mac &&
754             !ether_addr_equal(adapter->vfinfo[vf].vf_mac_addresses, new_mac)) {
755                 e_warn(drv,
756                        "VF %d attempted to override administratively set MAC address\n"
757                        "Reload the VF driver to resume operations\n",
758                        vf);
759                 return -1;
760         }
761
762         return ixgbe_set_vf_mac(adapter, vf, new_mac) < 0;
763 }
764
765 static int ixgbe_find_vlvf_entry(struct ixgbe_hw *hw, u32 vlan)
766 {
767         u32 vlvf;
768         s32 regindex;
769
770         /* short cut the special case */
771         if (vlan == 0)
772                 return 0;
773
774         /* Search for the vlan id in the VLVF entries */
775         for (regindex = 1; regindex < IXGBE_VLVF_ENTRIES; regindex++) {
776                 vlvf = IXGBE_READ_REG(hw, IXGBE_VLVF(regindex));
777                 if ((vlvf & VLAN_VID_MASK) == vlan)
778                         break;
779         }
780
781         /* Return a negative value if not found */
782         if (regindex >= IXGBE_VLVF_ENTRIES)
783                 regindex = -1;
784
785         return regindex;
786 }
787
788 static int ixgbe_set_vf_vlan_msg(struct ixgbe_adapter *adapter,
789                                  u32 *msgbuf, u32 vf)
790 {
791         struct ixgbe_hw *hw = &adapter->hw;
792         int add = (msgbuf[0] & IXGBE_VT_MSGINFO_MASK) >> IXGBE_VT_MSGINFO_SHIFT;
793         int vid = (msgbuf[1] & IXGBE_VLVF_VLANID_MASK);
794         int err;
795         s32 reg_ndx;
796         u32 vlvf;
797         u32 bits;
798         u8 tcs = netdev_get_num_tc(adapter->netdev);
799
800         if (adapter->vfinfo[vf].pf_vlan || tcs) {
801                 e_warn(drv,
802                        "VF %d attempted to override administratively set VLAN configuration\n"
803                        "Reload the VF driver to resume operations\n",
804                        vf);
805                 return -1;
806         }
807
808         if (add)
809                 adapter->vfinfo[vf].vlan_count++;
810         else if (adapter->vfinfo[vf].vlan_count)
811                 adapter->vfinfo[vf].vlan_count--;
812
813         /* in case of promiscuous mode any VLAN filter set for a VF must
814          * also have the PF pool added to it.
815          */
816         if (add && adapter->netdev->flags & IFF_PROMISC)
817                 err = ixgbe_set_vf_vlan(adapter, add, vid, VMDQ_P(0));
818
819         err = ixgbe_set_vf_vlan(adapter, add, vid, vf);
820         if (!err && adapter->vfinfo[vf].spoofchk_enabled)
821                 hw->mac.ops.set_vlan_anti_spoofing(hw, true, vf);
822
823         /* Go through all the checks to see if the VLAN filter should
824          * be wiped completely.
825          */
826         if (!add && adapter->netdev->flags & IFF_PROMISC) {
827                 reg_ndx = ixgbe_find_vlvf_entry(hw, vid);
828                 if (reg_ndx < 0)
829                         return err;
830                 vlvf = IXGBE_READ_REG(hw, IXGBE_VLVF(reg_ndx));
831                 /* See if any other pools are set for this VLAN filter
832                  * entry other than the PF.
833                  */
834                 if (VMDQ_P(0) < 32) {
835                         bits = IXGBE_READ_REG(hw, IXGBE_VLVFB(reg_ndx * 2));
836                         bits &= ~(1 << VMDQ_P(0));
837                         bits |= IXGBE_READ_REG(hw,
838                                                IXGBE_VLVFB(reg_ndx * 2) + 1);
839                 } else {
840                         bits = IXGBE_READ_REG(hw,
841                                               IXGBE_VLVFB(reg_ndx * 2) + 1);
842                         bits &= ~(1 << (VMDQ_P(0) - 32));
843                         bits |= IXGBE_READ_REG(hw, IXGBE_VLVFB(reg_ndx * 2));
844                 }
845
846                 /* If the filter was removed then ensure PF pool bit
847                  * is cleared if the PF only added itself to the pool
848                  * because the PF is in promiscuous mode.
849                  */
850                 if ((vlvf & VLAN_VID_MASK) == vid &&
851                     !test_bit(vid, adapter->active_vlans) && !bits)
852                         ixgbe_set_vf_vlan(adapter, add, vid, VMDQ_P(0));
853         }
854
855         return err;
856 }
857
858 static int ixgbe_set_vf_macvlan_msg(struct ixgbe_adapter *adapter,
859                                     u32 *msgbuf, u32 vf)
860 {
861         u8 *new_mac = ((u8 *)(&msgbuf[1]));
862         int index = (msgbuf[0] & IXGBE_VT_MSGINFO_MASK) >>
863                     IXGBE_VT_MSGINFO_SHIFT;
864         int err;
865
866         if (adapter->vfinfo[vf].pf_set_mac && index > 0) {
867                 e_warn(drv,
868                        "VF %d requested MACVLAN filter but is administratively denied\n",
869                        vf);
870                 return -1;
871         }
872
873         /* An non-zero index indicates the VF is setting a filter */
874         if (index) {
875                 if (!is_valid_ether_addr(new_mac)) {
876                         e_warn(drv, "VF %d attempted to set invalid mac\n", vf);
877                         return -1;
878                 }
879
880                 /*
881                  * If the VF is allowed to set MAC filters then turn off
882                  * anti-spoofing to avoid false positives.
883                  */
884                 if (adapter->vfinfo[vf].spoofchk_enabled)
885                         ixgbe_ndo_set_vf_spoofchk(adapter->netdev, vf, false);
886         }
887
888         err = ixgbe_set_vf_macvlan(adapter, vf, index, new_mac);
889         if (err == -ENOSPC)
890                 e_warn(drv,
891                        "VF %d has requested a MACVLAN filter but there is no space for it\n",
892                        vf);
893
894         return err < 0;
895 }
896
897 static int ixgbe_negotiate_vf_api(struct ixgbe_adapter *adapter,
898                                   u32 *msgbuf, u32 vf)
899 {
900         int api = msgbuf[1];
901
902         switch (api) {
903         case ixgbe_mbox_api_10:
904         case ixgbe_mbox_api_11:
905         case ixgbe_mbox_api_12:
906                 adapter->vfinfo[vf].vf_api = api;
907                 return 0;
908         default:
909                 break;
910         }
911
912         e_info(drv, "VF %d requested invalid api version %u\n", vf, api);
913
914         return -1;
915 }
916
917 static int ixgbe_get_vf_queues(struct ixgbe_adapter *adapter,
918                                u32 *msgbuf, u32 vf)
919 {
920         struct net_device *dev = adapter->netdev;
921         struct ixgbe_ring_feature *vmdq = &adapter->ring_feature[RING_F_VMDQ];
922         unsigned int default_tc = 0;
923         u8 num_tcs = netdev_get_num_tc(dev);
924
925         /* verify the PF is supporting the correct APIs */
926         switch (adapter->vfinfo[vf].vf_api) {
927         case ixgbe_mbox_api_20:
928         case ixgbe_mbox_api_11:
929         case ixgbe_mbox_api_12:
930                 break;
931         default:
932                 return -1;
933         }
934
935         /* only allow 1 Tx queue for bandwidth limiting */
936         msgbuf[IXGBE_VF_TX_QUEUES] = __ALIGN_MASK(1, ~vmdq->mask);
937         msgbuf[IXGBE_VF_RX_QUEUES] = __ALIGN_MASK(1, ~vmdq->mask);
938
939         /* if TCs > 1 determine which TC belongs to default user priority */
940         if (num_tcs > 1)
941                 default_tc = netdev_get_prio_tc_map(dev, adapter->default_up);
942
943         /* notify VF of need for VLAN tag stripping, and correct queue */
944         if (num_tcs)
945                 msgbuf[IXGBE_VF_TRANS_VLAN] = num_tcs;
946         else if (adapter->vfinfo[vf].pf_vlan || adapter->vfinfo[vf].pf_qos)
947                 msgbuf[IXGBE_VF_TRANS_VLAN] = 1;
948         else
949                 msgbuf[IXGBE_VF_TRANS_VLAN] = 0;
950
951         /* notify VF of default queue */
952         msgbuf[IXGBE_VF_DEF_QUEUE] = default_tc;
953
954         return 0;
955 }
956
957 static int ixgbe_get_vf_reta(struct ixgbe_adapter *adapter, u32 *msgbuf, u32 vf)
958 {
959         u32 i, j;
960         u32 *out_buf = &msgbuf[1];
961         const u8 *reta = adapter->rss_indir_tbl;
962         u32 reta_size = ixgbe_rss_indir_tbl_entries(adapter);
963
964         /* Check if operation is permitted */
965         if (!adapter->vfinfo[vf].rss_query_enabled)
966                 return -EPERM;
967
968         /* verify the PF is supporting the correct API */
969         if (adapter->vfinfo[vf].vf_api != ixgbe_mbox_api_12)
970                 return -EOPNOTSUPP;
971
972         /* This mailbox command is supported (required) only for 82599 and x540
973          * VFs which support up to 4 RSS queues. Therefore we will compress the
974          * RETA by saving only 2 bits from each entry. This way we will be able
975          * to transfer the whole RETA in a single mailbox operation.
976          */
977         for (i = 0; i < reta_size / 16; i++) {
978                 out_buf[i] = 0;
979                 for (j = 0; j < 16; j++)
980                         out_buf[i] |= (u32)(reta[16 * i + j] & 0x3) << (2 * j);
981         }
982
983         return 0;
984 }
985
986 static int ixgbe_get_vf_rss_key(struct ixgbe_adapter *adapter,
987                                 u32 *msgbuf, u32 vf)
988 {
989         u32 *rss_key = &msgbuf[1];
990
991         /* Check if the operation is permitted */
992         if (!adapter->vfinfo[vf].rss_query_enabled)
993                 return -EPERM;
994
995         /* verify the PF is supporting the correct API */
996         if (adapter->vfinfo[vf].vf_api != ixgbe_mbox_api_12)
997                 return -EOPNOTSUPP;
998
999         memcpy(rss_key, adapter->rss_key, sizeof(adapter->rss_key));
1000
1001         return 0;
1002 }
1003
1004 static int ixgbe_rcv_msg_from_vf(struct ixgbe_adapter *adapter, u32 vf)
1005 {
1006         u32 mbx_size = IXGBE_VFMAILBOX_SIZE;
1007         u32 msgbuf[IXGBE_VFMAILBOX_SIZE];
1008         struct ixgbe_hw *hw = &adapter->hw;
1009         s32 retval;
1010
1011         retval = ixgbe_read_mbx(hw, msgbuf, mbx_size, vf);
1012
1013         if (retval) {
1014                 pr_err("Error receiving message from VF\n");
1015                 return retval;
1016         }
1017
1018         /* this is a message we already processed, do nothing */
1019         if (msgbuf[0] & (IXGBE_VT_MSGTYPE_ACK | IXGBE_VT_MSGTYPE_NACK))
1020                 return 0;
1021
1022         /* flush the ack before we write any messages back */
1023         IXGBE_WRITE_FLUSH(hw);
1024
1025         if (msgbuf[0] == IXGBE_VF_RESET)
1026                 return ixgbe_vf_reset_msg(adapter, vf);
1027
1028         /*
1029          * until the vf completes a virtual function reset it should not be
1030          * allowed to start any configuration.
1031          */
1032         if (!adapter->vfinfo[vf].clear_to_send) {
1033                 msgbuf[0] |= IXGBE_VT_MSGTYPE_NACK;
1034                 ixgbe_write_mbx(hw, msgbuf, 1, vf);
1035                 return 0;
1036         }
1037
1038         switch ((msgbuf[0] & 0xFFFF)) {
1039         case IXGBE_VF_SET_MAC_ADDR:
1040                 retval = ixgbe_set_vf_mac_addr(adapter, msgbuf, vf);
1041                 break;
1042         case IXGBE_VF_SET_MULTICAST:
1043                 retval = ixgbe_set_vf_multicasts(adapter, msgbuf, vf);
1044                 break;
1045         case IXGBE_VF_SET_VLAN:
1046                 retval = ixgbe_set_vf_vlan_msg(adapter, msgbuf, vf);
1047                 break;
1048         case IXGBE_VF_SET_LPE:
1049                 retval = ixgbe_set_vf_lpe(adapter, msgbuf, vf);
1050                 break;
1051         case IXGBE_VF_SET_MACVLAN:
1052                 retval = ixgbe_set_vf_macvlan_msg(adapter, msgbuf, vf);
1053                 break;
1054         case IXGBE_VF_API_NEGOTIATE:
1055                 retval = ixgbe_negotiate_vf_api(adapter, msgbuf, vf);
1056                 break;
1057         case IXGBE_VF_GET_QUEUES:
1058                 retval = ixgbe_get_vf_queues(adapter, msgbuf, vf);
1059                 break;
1060         case IXGBE_VF_GET_RETA:
1061                 retval = ixgbe_get_vf_reta(adapter, msgbuf, vf);
1062                 break;
1063         case IXGBE_VF_GET_RSS_KEY:
1064                 retval = ixgbe_get_vf_rss_key(adapter, msgbuf, vf);
1065                 break;
1066         default:
1067                 e_err(drv, "Unhandled Msg %8.8x\n", msgbuf[0]);
1068                 retval = IXGBE_ERR_MBX;
1069                 break;
1070         }
1071
1072         /* notify the VF of the results of what it sent us */
1073         if (retval)
1074                 msgbuf[0] |= IXGBE_VT_MSGTYPE_NACK;
1075         else
1076                 msgbuf[0] |= IXGBE_VT_MSGTYPE_ACK;
1077
1078         msgbuf[0] |= IXGBE_VT_MSGTYPE_CTS;
1079
1080         ixgbe_write_mbx(hw, msgbuf, mbx_size, vf);
1081
1082         return retval;
1083 }
1084
1085 static void ixgbe_rcv_ack_from_vf(struct ixgbe_adapter *adapter, u32 vf)
1086 {
1087         struct ixgbe_hw *hw = &adapter->hw;
1088         u32 msg = IXGBE_VT_MSGTYPE_NACK;
1089
1090         /* if device isn't clear to send it shouldn't be reading either */
1091         if (!adapter->vfinfo[vf].clear_to_send)
1092                 ixgbe_write_mbx(hw, &msg, 1, vf);
1093 }
1094
1095 void ixgbe_msg_task(struct ixgbe_adapter *adapter)
1096 {
1097         struct ixgbe_hw *hw = &adapter->hw;
1098         u32 vf;
1099
1100         for (vf = 0; vf < adapter->num_vfs; vf++) {
1101                 /* process any reset requests */
1102                 if (!ixgbe_check_for_rst(hw, vf))
1103                         ixgbe_vf_reset_event(adapter, vf);
1104
1105                 /* process any messages pending */
1106                 if (!ixgbe_check_for_msg(hw, vf))
1107                         ixgbe_rcv_msg_from_vf(adapter, vf);
1108
1109                 /* process any acks */
1110                 if (!ixgbe_check_for_ack(hw, vf))
1111                         ixgbe_rcv_ack_from_vf(adapter, vf);
1112         }
1113 }
1114
1115 void ixgbe_disable_tx_rx(struct ixgbe_adapter *adapter)
1116 {
1117         struct ixgbe_hw *hw = &adapter->hw;
1118
1119         /* disable transmit and receive for all vfs */
1120         IXGBE_WRITE_REG(hw, IXGBE_VFTE(0), 0);
1121         IXGBE_WRITE_REG(hw, IXGBE_VFTE(1), 0);
1122
1123         IXGBE_WRITE_REG(hw, IXGBE_VFRE(0), 0);
1124         IXGBE_WRITE_REG(hw, IXGBE_VFRE(1), 0);
1125 }
1126
1127 void ixgbe_ping_all_vfs(struct ixgbe_adapter *adapter)
1128 {
1129         struct ixgbe_hw *hw = &adapter->hw;
1130         u32 ping;
1131         int i;
1132
1133         for (i = 0 ; i < adapter->num_vfs; i++) {
1134                 ping = IXGBE_PF_CONTROL_MSG;
1135                 if (adapter->vfinfo[i].clear_to_send)
1136                         ping |= IXGBE_VT_MSGTYPE_CTS;
1137                 ixgbe_write_mbx(hw, &ping, 1, i);
1138         }
1139 }
1140
1141 int ixgbe_ndo_set_vf_mac(struct net_device *netdev, int vf, u8 *mac)
1142 {
1143         struct ixgbe_adapter *adapter = netdev_priv(netdev);
1144         if (!is_valid_ether_addr(mac) || (vf >= adapter->num_vfs))
1145                 return -EINVAL;
1146         adapter->vfinfo[vf].pf_set_mac = true;
1147         dev_info(&adapter->pdev->dev, "setting MAC %pM on VF %d\n", mac, vf);
1148         dev_info(&adapter->pdev->dev, "Reload the VF driver to make this"
1149                                       " change effective.");
1150         if (test_bit(__IXGBE_DOWN, &adapter->state)) {
1151                 dev_warn(&adapter->pdev->dev, "The VF MAC address has been set,"
1152                          " but the PF device is not up.\n");
1153                 dev_warn(&adapter->pdev->dev, "Bring the PF device up before"
1154                          " attempting to use the VF device.\n");
1155         }
1156         return ixgbe_set_vf_mac(adapter, vf, mac);
1157 }
1158
1159 static int ixgbe_enable_port_vlan(struct ixgbe_adapter *adapter, int vf,
1160                                   u16 vlan, u8 qos)
1161 {
1162         struct ixgbe_hw *hw = &adapter->hw;
1163         int err;
1164
1165         err = ixgbe_set_vf_vlan(adapter, true, vlan, vf);
1166         if (err)
1167                 goto out;
1168
1169         ixgbe_set_vmvir(adapter, vlan, qos, vf);
1170         ixgbe_set_vmolr(hw, vf, false);
1171         if (adapter->vfinfo[vf].spoofchk_enabled)
1172                 hw->mac.ops.set_vlan_anti_spoofing(hw, true, vf);
1173         adapter->vfinfo[vf].vlan_count++;
1174
1175         /* enable hide vlan on X550 */
1176         if (hw->mac.type >= ixgbe_mac_X550)
1177                 ixgbe_write_qde(adapter, vf, IXGBE_QDE_ENABLE |
1178                                 IXGBE_QDE_HIDE_VLAN);
1179
1180         adapter->vfinfo[vf].pf_vlan = vlan;
1181         adapter->vfinfo[vf].pf_qos = qos;
1182         dev_info(&adapter->pdev->dev,
1183                  "Setting VLAN %d, QOS 0x%x on VF %d\n", vlan, qos, vf);
1184         if (test_bit(__IXGBE_DOWN, &adapter->state)) {
1185                 dev_warn(&adapter->pdev->dev,
1186                          "The VF VLAN has been set, but the PF device is not up.\n");
1187                 dev_warn(&adapter->pdev->dev,
1188                          "Bring the PF device up before attempting to use the VF device.\n");
1189         }
1190
1191 out:
1192         return err;
1193 }
1194
1195 static int ixgbe_disable_port_vlan(struct ixgbe_adapter *adapter, int vf)
1196 {
1197         struct ixgbe_hw *hw = &adapter->hw;
1198         int err;
1199
1200         err = ixgbe_set_vf_vlan(adapter, false,
1201                                 adapter->vfinfo[vf].pf_vlan, vf);
1202         ixgbe_clear_vmvir(adapter, vf);
1203         ixgbe_set_vmolr(hw, vf, true);
1204         hw->mac.ops.set_vlan_anti_spoofing(hw, false, vf);
1205         if (adapter->vfinfo[vf].vlan_count)
1206                 adapter->vfinfo[vf].vlan_count--;
1207
1208         /* disable hide VLAN on X550 */
1209         if (hw->mac.type >= ixgbe_mac_X550)
1210                 ixgbe_write_qde(adapter, vf, IXGBE_QDE_ENABLE);
1211
1212         adapter->vfinfo[vf].pf_vlan = 0;
1213         adapter->vfinfo[vf].pf_qos = 0;
1214
1215         return err;
1216 }
1217
1218 int ixgbe_ndo_set_vf_vlan(struct net_device *netdev, int vf, u16 vlan, u8 qos)
1219 {
1220         int err = 0;
1221         struct ixgbe_adapter *adapter = netdev_priv(netdev);
1222
1223         if ((vf >= adapter->num_vfs) || (vlan > 4095) || (qos > 7))
1224                 return -EINVAL;
1225         if (vlan || qos) {
1226                 /* Check if there is already a port VLAN set, if so
1227                  * we have to delete the old one first before we
1228                  * can set the new one.  The usage model had
1229                  * previously assumed the user would delete the
1230                  * old port VLAN before setting a new one but this
1231                  * is not necessarily the case.
1232                  */
1233                 if (adapter->vfinfo[vf].pf_vlan)
1234                         err = ixgbe_disable_port_vlan(adapter, vf);
1235                 if (err)
1236                         goto out;
1237                 err = ixgbe_enable_port_vlan(adapter, vf, vlan, qos);
1238         } else {
1239                 err = ixgbe_disable_port_vlan(adapter, vf);
1240         }
1241
1242 out:
1243         return err;
1244 }
1245
1246 static int ixgbe_link_mbps(struct ixgbe_adapter *adapter)
1247 {
1248         switch (adapter->link_speed) {
1249         case IXGBE_LINK_SPEED_100_FULL:
1250                 return 100;
1251         case IXGBE_LINK_SPEED_1GB_FULL:
1252                 return 1000;
1253         case IXGBE_LINK_SPEED_10GB_FULL:
1254                 return 10000;
1255         default:
1256                 return 0;
1257         }
1258 }
1259
1260 static void ixgbe_set_vf_rate_limit(struct ixgbe_adapter *adapter, int vf)
1261 {
1262         struct ixgbe_ring_feature *vmdq = &adapter->ring_feature[RING_F_VMDQ];
1263         struct ixgbe_hw *hw = &adapter->hw;
1264         u32 bcnrc_val = 0;
1265         u16 queue, queues_per_pool;
1266         u16 tx_rate = adapter->vfinfo[vf].tx_rate;
1267
1268         if (tx_rate) {
1269                 /* start with base link speed value */
1270                 bcnrc_val = adapter->vf_rate_link_speed;
1271
1272                 /* Calculate the rate factor values to set */
1273                 bcnrc_val <<= IXGBE_RTTBCNRC_RF_INT_SHIFT;
1274                 bcnrc_val /= tx_rate;
1275
1276                 /* clear everything but the rate factor */
1277                 bcnrc_val &= IXGBE_RTTBCNRC_RF_INT_MASK |
1278                              IXGBE_RTTBCNRC_RF_DEC_MASK;
1279
1280                 /* enable the rate scheduler */
1281                 bcnrc_val |= IXGBE_RTTBCNRC_RS_ENA;
1282         }
1283
1284         /*
1285          * Set global transmit compensation time to the MMW_SIZE in RTTBCNRM
1286          * register. Typically MMW_SIZE=0x014 if 9728-byte jumbo is supported
1287          * and 0x004 otherwise.
1288          */
1289         switch (hw->mac.type) {
1290         case ixgbe_mac_82599EB:
1291                 IXGBE_WRITE_REG(hw, IXGBE_RTTBCNRM, 0x4);
1292                 break;
1293         case ixgbe_mac_X540:
1294                 IXGBE_WRITE_REG(hw, IXGBE_RTTBCNRM, 0x14);
1295                 break;
1296         default:
1297                 break;
1298         }
1299
1300         /* determine how many queues per pool based on VMDq mask */
1301         queues_per_pool = __ALIGN_MASK(1, ~vmdq->mask);
1302
1303         /* write value for all Tx queues belonging to VF */
1304         for (queue = 0; queue < queues_per_pool; queue++) {
1305                 unsigned int reg_idx = (vf * queues_per_pool) + queue;
1306
1307                 IXGBE_WRITE_REG(hw, IXGBE_RTTDQSEL, reg_idx);
1308                 IXGBE_WRITE_REG(hw, IXGBE_RTTBCNRC, bcnrc_val);
1309         }
1310 }
1311
1312 void ixgbe_check_vf_rate_limit(struct ixgbe_adapter *adapter)
1313 {
1314         int i;
1315
1316         /* VF Tx rate limit was not set */
1317         if (!adapter->vf_rate_link_speed)
1318                 return;
1319
1320         if (ixgbe_link_mbps(adapter) != adapter->vf_rate_link_speed) {
1321                 adapter->vf_rate_link_speed = 0;
1322                 dev_info(&adapter->pdev->dev,
1323                          "Link speed has been changed. VF Transmit rate is disabled\n");
1324         }
1325
1326         for (i = 0; i < adapter->num_vfs; i++) {
1327                 if (!adapter->vf_rate_link_speed)
1328                         adapter->vfinfo[i].tx_rate = 0;
1329
1330                 ixgbe_set_vf_rate_limit(adapter, i);
1331         }
1332 }
1333
1334 int ixgbe_ndo_set_vf_bw(struct net_device *netdev, int vf, int min_tx_rate,
1335                         int max_tx_rate)
1336 {
1337         struct ixgbe_adapter *adapter = netdev_priv(netdev);
1338         int link_speed;
1339
1340         /* verify VF is active */
1341         if (vf >= adapter->num_vfs)
1342                 return -EINVAL;
1343
1344         /* verify link is up */
1345         if (!adapter->link_up)
1346                 return -EINVAL;
1347
1348         /* verify we are linked at 10Gbps */
1349         link_speed = ixgbe_link_mbps(adapter);
1350         if (link_speed != 10000)
1351                 return -EINVAL;
1352
1353         if (min_tx_rate)
1354                 return -EINVAL;
1355
1356         /* rate limit cannot be less than 10Mbs or greater than link speed */
1357         if (max_tx_rate && ((max_tx_rate <= 10) || (max_tx_rate > link_speed)))
1358                 return -EINVAL;
1359
1360         /* store values */
1361         adapter->vf_rate_link_speed = link_speed;
1362         adapter->vfinfo[vf].tx_rate = max_tx_rate;
1363
1364         /* update hardware configuration */
1365         ixgbe_set_vf_rate_limit(adapter, vf);
1366
1367         return 0;
1368 }
1369
1370 int ixgbe_ndo_set_vf_spoofchk(struct net_device *netdev, int vf, bool setting)
1371 {
1372         struct ixgbe_adapter *adapter = netdev_priv(netdev);
1373         int vf_target_reg = vf >> 3;
1374         int vf_target_shift = vf % 8;
1375         struct ixgbe_hw *hw = &adapter->hw;
1376         u32 regval;
1377
1378         if (vf >= adapter->num_vfs)
1379                 return -EINVAL;
1380
1381         adapter->vfinfo[vf].spoofchk_enabled = setting;
1382
1383         regval = IXGBE_READ_REG(hw, IXGBE_PFVFSPOOF(vf_target_reg));
1384         regval &= ~(1 << vf_target_shift);
1385         regval |= (setting << vf_target_shift);
1386         IXGBE_WRITE_REG(hw, IXGBE_PFVFSPOOF(vf_target_reg), regval);
1387
1388         if (adapter->vfinfo[vf].vlan_count) {
1389                 vf_target_shift += IXGBE_SPOOF_VLANAS_SHIFT;
1390                 regval = IXGBE_READ_REG(hw, IXGBE_PFVFSPOOF(vf_target_reg));
1391                 regval &= ~(1 << vf_target_shift);
1392                 regval |= (setting << vf_target_shift);
1393                 IXGBE_WRITE_REG(hw, IXGBE_PFVFSPOOF(vf_target_reg), regval);
1394         }
1395
1396         return 0;
1397 }
1398
1399 int ixgbe_ndo_set_vf_rss_query_en(struct net_device *netdev, int vf,
1400                                   bool setting)
1401 {
1402         struct ixgbe_adapter *adapter = netdev_priv(netdev);
1403
1404         /* This operation is currently supported only for 82599 and x540
1405          * devices.
1406          */
1407         if (adapter->hw.mac.type < ixgbe_mac_82599EB ||
1408             adapter->hw.mac.type >= ixgbe_mac_X550)
1409                 return -EOPNOTSUPP;
1410
1411         if (vf >= adapter->num_vfs)
1412                 return -EINVAL;
1413
1414         adapter->vfinfo[vf].rss_query_enabled = setting;
1415
1416         return 0;
1417 }
1418
1419 int ixgbe_ndo_get_vf_config(struct net_device *netdev,
1420                             int vf, struct ifla_vf_info *ivi)
1421 {
1422         struct ixgbe_adapter *adapter = netdev_priv(netdev);
1423         if (vf >= adapter->num_vfs)
1424                 return -EINVAL;
1425         ivi->vf = vf;
1426         memcpy(&ivi->mac, adapter->vfinfo[vf].vf_mac_addresses, ETH_ALEN);
1427         ivi->max_tx_rate = adapter->vfinfo[vf].tx_rate;
1428         ivi->min_tx_rate = 0;
1429         ivi->vlan = adapter->vfinfo[vf].pf_vlan;
1430         ivi->qos = adapter->vfinfo[vf].pf_qos;
1431         ivi->spoofchk = adapter->vfinfo[vf].spoofchk_enabled;
1432         ivi->rss_query_en = adapter->vfinfo[vf].rss_query_enabled;
1433         return 0;
1434 }