1 =================================================================================================
2 OPNFV Build instruction for the Brahmaputra release of OPNFV when using Fuel as a deployment tool
3 =================================================================================================
8 This work is licensed under a Creative Commons Attribution 4.0
9 International License. .. http://creativecommons.org/licenses/by/4.0 ..
10 (c) Jonas Bjurel (Ericsson AB) and others
15 This document describes how to build the Fuel deployment tool for the
16 Brahmaputra release of OPNFV build system, dependencies and required
22 This document describes the build system used to build the Fuel
23 deployment tool for the Brahmaputra release of OPNFV, required
24 dependencies and minimum requirements on the host to be used for the
27 The Fuel build system is designed around Docker containers such that
28 dependencies outside of the build system can be kept to a minimum. It
29 also shields the host from any potential dangerous operations
30 performed by the build system.
32 The audience of this document is assumed to have good knowledge in
33 network and Unix/Linux administration.
38 Minimum Hardware Requirements
39 -----------------------------
41 - ~30 GB available disc
45 Minimum Software Requirements
46 -----------------------------
48 The build host should run Ubuntu 14.04 operating system.
50 On the host, the following packages must be installed:
52 - An x86_64 host (Bare-metal or VM) with Ubuntu 14.04 LTS installed
54 - A kernel equal- or later than 3.19 (Vivid) (simply available through sudo apt-get install linux-generic-lts-vivid)
56 - **Note:** Builds on Wily (Ubuntu 15.x) are currently not supported
58 - docker - see https://docs.docker.com/engine/installation/ubuntulinux/ for installation notes for Ubuntu 14.04. Tested against version 1.9.x and greater
60 - git (simply available through $ sudo apt-get install git)
62 - make (simply available through $ sudo apt-get install make)
64 - curl (simply available through $ sudo apt-get install curl)
69 Setting up the Docker build container
70 -------------------------------------
71 After having installed Docker, add yourself to the docker group:
73 $ sudo usermod -a -G docker [userid]
75 Also make sure to define relevant DNS servers part of the global
76 DNS chain in your </etc/default/docker> configuration file.
77 Uncomment, and modify the values appropriately.
81 <DOCKER_OPTS=" --dns=8.8.8.8 --dns=8.8.8.4">
85 .. code-block:: console
87 $ sudo service docker restart
89 Setting up OPNFV Gerrit in order to being able to clone the code
90 ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
91 - Start setting up OPNFV gerrit by creating a SSH key (unless you
92 don't already have one), create one with ssh-keygen
94 - Add your generated public key in OPNFV Gerrit <https://gerrit.opnfv.org/>
95 (this requires a Linux foundation account, create one if you do not
98 - Select "SSH Public Keys" to the left and then "Add Key" and paste
101 Clone the OPNFV code Git repository with your SSH key
102 ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
103 Now it is time to clone the code repository:
105 $ git clone ssh://<Linux foundation user>@gerrit.opnfv.org:29418/fuel
107 Now you should have the OPNFV fuel repository with the Fuel
108 directories stored locally on your build host.
110 Check out the Brahmaputra release:
112 $ git checkout brahmaputra.1.0
114 Clone the OPNFV code Git repository without a SSH key
115 ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
116 You can also opt to clone the code repository without a SSH key:
118 $ git clone https://gerrit.opnfv.org:29418/gerrit/fuel
120 Make sure to checkout the release tag as described above.
122 Support for building behind a http/https/rsync proxy
123 ----------------------------------------------------
125 The build system is able to make use of a web proxy setup if the
126 http_proxy, https_proxy, no_proxy (if needed) and RSYNC_PROXY or
127 RSYNC_CONNECT_PROG environment variables have been set before invoking make.
129 The proxy setup must permit port 80 (http), 443 (https) and 873
132 Important note about the host Docker daemon settings
133 ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
135 The Docker daemon on the host must be configured to use the http proxy
136 for it to be able to pull the base Ubuntu 14.04 image from the Docker
137 registry before invoking make! In Ubuntu this is done by adding a line
140 export http_proxy="http://10.0.0.1:8888/"
142 to /etc/default/docker and restarting the Docker daemon.
144 Setting proxy environment variables prior to build
145 ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
147 The build system will make use the following environment variables
148 that needs to be exported to subshells by using export (bash) or
151 | http_proxy (or HTTP_PROXY)
152 | https_proxy (or HTTP_PROXY)
153 | no_proxy (or NO_PROXY)
157 As an example, these are the settings that were put in the user's
158 .bashrc when verifying the proxy build functionality:
160 | export RSYNC_PROXY=10.0.0.1:8888
161 | export http_proxy=http://10.0.0.1:8888
162 | export https_proxy=http://10.0.0.1:8888
163 | export no_proxy=localhost,127.0.0.1,.consultron.com,.sock
165 Using a ssh proxy for the rsync connection
166 ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
168 If the proxy setup is not allowing the rsync protocol, an alternative
169 solution is to use a SSH tunnel to a machine capable of accessing the
170 outbound port 873. Set the RSYNC_CONNECT_PROG according to the rsync
171 manual page (for example to "ssh <username>@<hostname> nc %H 873")
172 to enable this. Also note that netcat needs to be installed on the
175 Make sure that the ssh command also refers to the user on the remote
176 system, as the command itself will be run from the Docker build container
177 as the root user (but with the invoking user's SSH keys).
179 Disabling the Ubuntu repo cache if rsync is not allowed
180 ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
182 During the build phase, a local Ubuntu package repository is fetched
183 from upstream in order to be added to the OPNFV Fuel ISO and for parts
184 of this process rsync is used.
186 If neither of the two available methods for proxying rsync are
187 available, the last resort is to turn off the caching of the Ubuntu
188 packages in the build system. This is done by removing the
189 "f_repobuild" from SUBDIRS in the beginning of
190 the fuel/build/f_isoroot/Makefile.
192 Note! Doing this will require the Fuel master node to have Internet
193 access when installing the ISO artifact built as no Ubuntu package
194 cache will be on the ISO!
196 Configure your build environment
197 --------------------------------
199 ** Configuring the build environment should not be performed if building
200 standard Brahmaputra release **
202 Select the versions of the components you want to build by editing the
203 fuel/build/config.mk file.
205 Non official build: Selecting which plugins to build
206 ----------------------------------------------------
207 In order to cut the build time for unofficial builds (made by an
208 individual developer locally), the selection if which Fuel plugins to
209 build (if any) can be done by environment variable
210 "BUILD_FUEL_PLUGINS" prior to building.
212 Only the plugin targets from fuel/build/f_isoroot/Makefile that are
213 specified in the environment variable will then be built. In order to
214 completely disable the building of plugins, the environment variable
215 is set to " ". When using this functionality, the resulting iso file
216 will be prepended with the prefix "unofficial-" to clearly indicate
217 that this is not a full build.
219 This method of plugin selection is not meant to be used from within
225 There are two methods available for building Fuel:
227 - A low level method using Make
229 - An abstracted method using build.sh
231 Low level build method using make
232 ---------------------------------
233 The low level method is based on Make:
235 From the <fuel/build> directory, invoke <make [target]>
237 Following targets exist:
239 - none/all - this will:
241 - Initialize the docker build environment
243 - Build Fuel from upstream (as defined by fuel-build/config-spec)
245 - Build the OPNFV defined plugins/features from upstream
247 - Build the defined additions to fuel (as defined by the structure
250 - Apply changes and patches to fuel (as defined by the structure of
253 - Reconstruct a fuel .iso image
255 - clean - this will remove all artifacts from earlier builds.
257 - debug - this will simply enter the build container without starting a build, from here you can start a build by enter "make iso"
259 If the build is successful, you will find the generated ISO file in
260 the <fuel/build/release> subdirectory!
262 Abstracted build method using build.sh
263 --------------------------------------
264 The abstracted build method uses the <fuel/ci/build.sh> script which
267 - Create and use a build cache - significantly speeding up the
268 build time if upstream repositories have not changed.
270 - push/pull cache and artifacts to an arbitrary URI (http(s):, file:, ftp:)
272 For more info type <fuel/ci/build.sh -h>.
277 The artifacts produced are:
279 - <OPNFV_XXXX.iso> - Which represents the bootable Fuel image, XXXX is
280 replaced with the build identity provided to the build system
282 - <OPNFV_XXXX.iso.txt> - Which holds version metadata.
287 1) OPNFV Installation instruction for the Brahmaputra release of OPNFV when using Fuel as a deployment tool
289 2) OPNFV Build instruction for the Brahmaputra release of OPNFV when using Fuel as a deployment tool
291 3) OPNFV Release Note for the Brahmaputra release of OPNFV when using Fuel as a deployment tool